Properties of ITO films prepared by reactive magnetron sputtering

Indium tin oxide (ITO) thin films were deposited by mid frequency pulsed dual magnetron sputtering using a metallic alloy target with 10 wt.% tin in an atmosphere of argon and oxygen. The aim of the work was to study the interdependence of structural, electrical and optical properties of ITO films deposited in the reactive and transition target mode, respectively. The deposition rate in the transition mode exceeds the deposition rate in the reactive mode by a factor of six, a maximum value of 100 nm·m min⁻¹ could be achieved. This corresponds to a static deposition rate of 200 nm min⁻¹. The lowest electrical resistivity of 1.1·10⁻³ Ω cm was measured at samples deposited in the high oxygen flow range in the transition mode. The samples show a good transparency in the visible range corresponding to extinction coefficients being below 10⁻². X-ray diffraction was used to characterise crystalline structure as well as film stress. ITO films prepared in the transition mode show a slightly preferred orientation in (211) direction, whereas films deposited in the reactive mode are strongly (222) oriented. Compared to undoped In₂O₃ all samples have an enlarged lattice. The lattice strain perpendicular to the surface is about 0.8% and 2.0% for films grown in the transition and the reactive mode, respectively. Deposition in the transition mode introduces a biaxial film stress in the range of −300 MPa, while stress in reactive mode samples is −1500 MPa.     

MECHANISM OF PHOTOOXYGENATION OF THE CD (II) COMPLEX OF PYROPHEOPHORBIDE A METHYL ESTER

Photooxygenation of (pyropheophorbidato a methyl ester)cadmium (II) was studied using ^18,18O₂ labeling of the molecular oxygen required for cleavage of the macrocycle. After reductive demetallation of the primary oxidation product (4,5-dioxo-4,5-secopyropheophorbidato a methyl ester)cadmium (II), the isotope content of formylbilinone 4a was analyzed by repeated-scan fast atom bombardment mass spectrometry. Comparison of the spectroscopic data of the labeled pigment 4a with the statistical probabilities of¹⁸ O isotope incorporation calculated for four possible reaction mechanisms clearly proves that photooxidative ring cleavage occurred by the one-molecule mechanism, i.e. the terminal oxygen atoms of 4a were derived from one oxygen molecule. Furthermore, a study of the exchange of the¹⁸ O-labeled atoms revealed that no exchange occurs within the pH 4.5–9.5 range. In stronger alkaline or acidic solutions, only the oxygen atom of the formyl group is exchanged. Hydrolysis of the methyl ester group of 4a was achieved, without loss of the¹⁸ O label on the formyl group, at pH 7.2 in the presence of pig liver esterase.     

Mixtures of charged colloid and neutral polymer: influence of electrostatic interactions on demixing and interfacial tension

The equilibrium phase behavior of a binary mixture of charged colloids and neutral, nonadsorbing polymers is studied within free-volume theory. A model mixture of charged hard-sphere macroions and ideal, coarse-grained, effective-sphere polymers is mapped first onto a binary hard-sphere mixture with nonadditive diameters and then onto an effective Asakura-Oosawa model [S. Asakura and F. Oosawa, J. Chem. Phys. 22, 1255 (1954)]. The effective model is defined by a single dimensionless parameter-the ratio of the polymer diameter to the effective colloid diameter. For high salt-to-counterion concentration ratios, a free-volume approximation for the free energy is used to compute the fluid phase diagram, which describes demixing into colloid-rich (liquid) and colloid-poor (vapor) phases. Increasing the range of electrostatic interactions shifts the demixing binodal toward higher polymer concentration, stabilizing the mixture. The enhanced stability is attributed to a weakening of polymer depletion-induced attraction between electrostatically repelling macroions. Comparison with predictions of density-functional theory reveals a corresponding increase in the liquid-vapor interfacial tension. The predicted trends in phase stability are consistent with observed behavior of protein-polysaccharide mixtures in food colloids.     

Trace analysis of rapamycin in human blood by micellar electrokinetic chromatography

A capillary electrophoretic method with UV detection at 278 nm has been developed for analysis of the immunosuppressant rapamycin (sirolimus) in human blood at low microgram per liter levels. Separation has been achieved in an acidic carrier electrolyte containing sodium dodecylsulfate and 30% (v/v) acetonitrile. For sample clean-up and preconcentration, an off-line solid-phase extraction step using a silica-based reversed-phase material and an on-capillary focussing technique were employed. The latter allows the injection of increased sample volumes without excessive band broadening. Although this new method is less sensitive than existing liquid chromatographic procedures combined with mass spectrometry, it is fully suited to routine analysis of rapamycin in blood from patients treated with this drug. Last but not least the low costs make it an attractive alternative to established methods.     

Kinetic versus thermodynamic control during the formation of [2]rotaxanes by a dynamic template-directed clipping process

A template-directed dynamic clipping procedure has generated a library of nine [2]rotaxanes that have been formed from three dialkylammonium salts-acting as the dumbbell-shaped components-and three dynamic, imino bond-containing, [24]crown-8-like macrocycles-acting as the ring-shaped components-which are themselves assembled from three dialdehydes and one diamine. The rates of formation of these [2]rotaxanes differ dramatically, from minutes to days depending on the choice of dialkylammonium ion and dialdehyde, as do their thermodynamic stabilities. Generally, [2]rotaxanes formed by using 2,6-diformylpyridine as the dialdehyde component, or bis(3,5-bis(trifluoromethyl)benzyl)ammonium hexafluorophosphate as the dumbbell-shaped component, assembled the most rapidly. Those rotaxanes containing this particular electron-deficient dumbbell-shaped unit, or 2,5-diformylfuran units in the macroring, were the most stable thermodynamically. The relative thermodynamic stabilities of all nine of the [2]rotaxanes were determined by competition experiments that were monitored by (1)H NMR spectroscopy.     

Deposition of Oral Bacteria and Polystyrene Particles to Quartz and Dental Enamel in a Parallel Plate and Stagnation Point Flow Chamber

The aim of this paper is to determine to what extent (i) deposition of oral bacteria and polystyrene particles, (ii) onto quartz and dental enamel with and without a salivary conditioning film, (iii) in a parallel plate (PP) and stagnation point (SP) flow chamber and at common Peclet numbers are comparable. All three bacterial strains showed different adhesion behaviors, and even Streptococcus mitis BMS, possessing a similar cell surface hydrophobicity as polystyrene particles, did not mimic polystyrene particles in its adhesion behavior, possibly as a result of the more negative ζ potentials of the polystyrene particles. The stationary endpoint adhesion of all strains, including polystyrene particles, was lower in the presence of a salivary conditioning film, while also desorption probabilities under flow were higher in the presence of a conditioning film than in its absence. Deposition onto quartz and enamel surfaces was different, but without a consistent trend valid for all strains and polystyrene particles. It is concluded that differences in experimental results exist, and the process of bacterial deposition to enamel surfaces cannot be modeled by using polystyrene particles and quartz collector surfaces.