Capillary electrophoresis analysis of gentamicin sulphate with UV detection after pre-capillary derivatization with 1,2-phthalic dicarboxaldehyde and mercaptoacetic acid

A selective, sensitive, and rapid pre-capillary derivatization method for determination of the multicomponent aminoglycoside antibiotic gentamicin is described. The derivatization reagents 1,2-phthalic dicarboxaldehyde and mercaptoacetic acid were used and the thioisoindole derivative was UV detected at 330 nm. A central composite experimental design was performed to optimize selectivity and derivatization conditions. Baseline separation of gentamicin C1, C1a, C2, C2a, C2b, sisomicin and several minor components was achieved with a background electrolyte containing 30 mM sodium tetraborate, 7.5 mM beta-cyclodextrin and 12.5% (v/v) methanol at pH 10. Quantitative analysis was performed and illustrated the potential use of capillary electrophoresis for the identification and quantitation of gentamicin as an alternative to methods prescribed in the United States Pharmacopeia and European Pharmacopoeia.     

Direct optical emission spectroscopy of liquid analytes using an electrolyte as a cathode discharge source (ELCAD) integrated on a micro-fluidic chip

Atomic emission detection of metallic species in aqueous solutions has been performed using a miniaturised plasma created within a planar, glass micro-fluidic chip. Detection was achieved using an Electrolyte as a Cathode Discharge source (ELCAD) in which the sample solution itself is used as the cathode for the discharge. To realise the ELCAD technique within a micro-fluidic device, a parallel liquid-gas flow was set up in a micro-channel and a glow discharge ignited between the flowing liquid sample surface and a metal wire anode. The detection of copper and sodium was achieved, using atmospheric pressure air as a carrier gas, by observation of atomic emission lines of copper at 324 nm, 327 nm, 511 nm, 515 nm and 522 nm and an atomic emission line of sodium at 589 nm using a commercially available miniaturised spectrometer. A total electrical power of less than 70 mW was required to sustain the discharge. A semi-quantitative, absolute detection limit of 17 nmol s(-1) was obtained for sodium with a sample flow rate of 100 microL min(-1) and an integration time of 100 ms in air at atmospheric pressure. The volume required for such detection is approximately 170 nL. Further analysis was performed with an Echelle spectrometer using both argon and air as a carrier gas. The geometry and flow rates used demonstrate the feasibility of integrating such micro-plasmas into other micro-fluidic devices, such as miniaturised CE devices, as a method of detection. The potential for using such micro-plasmas within highly portable miniaturised systems and mu-TAS devices is presented and discussed.     

Development and application of an integrated system for monitoring ethanol content of fuels

An automated flow injection analysis (FIA) system for quantifying ethanol was developed using alcohol oxidase, horseradish peroxidase, 4-aminophenazone, and phenol. A colorimetric detection method was developed using two different methods of analysis, with free and immobilized enzymes. The system with free enzymes permitted analysis of standard ethanol solution in a range of 0.05–1.0 g of ethanol/L without external dilution, a sampling frequency of 15 analyses/h, and relative SD of 3.5%. A new system was designed consisting of a microreactor with a 0.91-mL internal volume filled with alcohol oxidase immobilized on glass beads and an addition of free peroxidase, adapted in an FIA line, for continued reuse. This integrated biosensor-FIA system is being used for quality control of biofuels, gasohol, and hydrated ethanol. The FIA system integrated with the microreactor showed a calibration curve in the range of 0.05–1.5 g of ethanol/L, and good results were obtained compared with the ethanol content measured by high-performance liquid chromatography and gas chromatography standard methods.     

Comparison of chemical properties of food products processed by conventional and ohmic heating

The effect of ohmic and conventional heat processing of different food products on their chemical and physical parameters was studied. Depending on the food being analysed, parameters such as pH, total solids, ash, titratable acidity, ascorbic acid, total sugars, total fatty acids, total phenolic compounds, and anthocyanins content were determined before and after ohmic and conventional pasteurization techniques and the results were compared using one-way analysis of variance. In goat milk samples treated by ohmic technology the pH value (6.58) and total fatty acids content in milk fat (86.5 mass %) were comparable to those found in milk treated by conventional process, however, ohmically treated samples presented a lower content of lactic acid, 0.13 %. In cloudberry jam samples treated by ohmic technology the results of some of the main parameters tested, such as total sugar content 46.1 mass %, ascorbic acid content 2.83 mass %, and titratable acidity 6.01 mass % (as citric acid) did not show significant differences when compared with samples treated by conventional technology. Presented at the 33rd International Conference of the Slovak Society of Chemical Engineering, Tatranské Matliare, 22–26 May 2006.     

A Three-Dimensional Two-Phase Model for Thermal Plasma Chemical Vapor Deposition with Liquid Feedstock Injection

In this paper, a comprehensive model for thermal plasma chemical vapor deposition (TPCVD) with liquid feedstock injection is documented. The gas flow is assumed to be steady, of a single temperature. Radiation and charged species contributions are excluded, but extensive homogeneous and heterogeneous chemistry is included. The liquid phase is traced by considering individual droplets. Discussion on the model's application to diamond production from acetone in a hydrogen–argon plasma is included. The major conclusions are: (1) Liquid injection possesses a capability to deliver the hydrocarbon precursor directly onto the deposition target. (2) For the case of complete evaporation of the droplet before reaching the substrate, the deposition rate is similar to that obtained with gaseous precursors. (3) The computational results compare well with experimental data. The modeling results can be used to optimize the injection parameters with regard to the deposition rate.     

Review: mass spectrometry of step-growth polymers

For at least two decades different mass spectrometric techniques have been applied for polymer analysis, including the qualitative determination of chemical compositions, end group identification, functionality type distribution and the determination of the cyclisation extend at each degree of polymerisation. Molecular weights exceeding 100 KDa are provable by MALDI-ToF mass spectrometry. Further, molecular weight distributions are determined by MADLI-ToF. However, there are some hints that, there is a discrimination against higher molecular weight species in samples with polydispersity of more than 1.2. Furthermore, pathways for dendritic and hyper-branched polymers, supramolecular polymers and nano condensates are analysed by help of mass spectrometry.     

Randregularität des\bar \partial -Problems für die Halbkugel in ℂn

Let f be a -closed (0, q+1)-form defined on the half ball B₊ in ⁿ, which is of class C^k on ¯B. We prove the existence with C^k-estimates of a solution u of the equation .

---

---

Die Anregung zu dieser Arbeit verdanke ich auch Herrn Piotr Jakóbczak aus Krakau, der sich eine gewisse Zeit am Max-Planck-Institut für Mathematik in Bonn aufhielt. Während dieser Zeit untersuchten wir die C⁰-Abschätzungen für die Halbkugel in ⁿ     

Development of a capillary electrophoretic method for the separation of diastereoisomers of a new human immunodeficiency virus protease inhibitor

A capillary electrophoretic (CE) method was developed for the separation of diastereoisomers of a new human immunodeficiency virus (HIV) protease inhibitor TMC114. In total 16 isomers of this drug have been synthesized (eight pairs of enantiomers). We succeeded in the separation of the eight diastereoisomers, but no enantiomers could be separated. Because of the high similarity and water-insolubility of these isomers, the separation is a real challenge. Different CE modes were tried out: capillary zone electrophoresis (CZE), nonaqueous capillary electrophoresis (NACE), micellar electrokinetic capillary chromatography (MEKC), and microemulsion electrokinetic capillary chromatography (MEEKC). Only MEEKC offered resolution of these compounds.