Structure Evolution upon Uniaxial Drawing Skin‐ and Core‐Layers of Injection‐Molded Isotactic Polypropylene by In Situ Synchrotron X‐ray Scattering

The structure evolution of the oriented layer (skin) and unoriented layer (core) from injection‐molded isotactic polypropylene samples upon uniaxial drawing is probed by in situ synchrotron X‐ray scattering. The X‐ray data analysis approach, called “halo method”, is used to semiquantitatively identify the transformation process of crystal phase upon uniaxial drawing. The results verify the validation of the stress‐induced crystal fragmentation and recrystallization process in the deformation of the injection‐molded samples under different temperatures. Furthermore, the end of strain softening region in the engineering stress‐strain curves explicitly corresponds to the transition point from the stress‐induced crystal fragmentation to recrystallization process. Basically, the skin and core layers of the injection‐molded parts share the similar deformation mechanism as aforementioned. The stretching temperature which dramatically affects the relative strength between the entanglement‐induced tie chains and the adjacent crystalline lamellae determines the crystal structural evolution upon drawing. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013, 51, 1618–1631     

Crystallization behavior of isotactic propylene‐1‐hexene random copolymer revealed by time‐resolved SAXS/WAXD techniques

The crystallization behavior of isotactic propylene‐1‐hexene (PH) random copolymer having 5.7% mole fraction of hexene content was investigated using simultaneous time‐resolved small‐angle X‐ray scattering (SAXS) and wide‐angle X‐ray diffraction (WAXD) techniques. For this copolymer, the hexene component cannot be incorporated into the unit cell structure of isotactic polypropylene (iPP). Only α‐phase crystal form of iPP was observed when samples were melt crystallized at temperatures of 40 °C, 60 °C, 80 °C, and 100 °C. Comprehensive analysis of SAXS and WAXD profiles indicated that the crystalline morphology is correlated with crystallization temperature. At high temperatures (e.g., 100 °C) the dominant morphology is the lamellar structure; while at low temperatures (e.g., 40 °C) only highly disordered small crystal blocks can be formed. These morphologies are kinetically controlled. Under a small degree of supercooling (the corresponding iPP crystallization rate is slow), a segmental segregation between iPP and hexene components probably takes place, leading to the formation of iPP lamellar crystals with a higher degree of order. In contrast, under a large degree of supercooling (the corresponding iPP crystallization rate is fast), defective small crystal blocks are favored due to the large thermodynamic driving force and low chain mobility. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 26–32, 2010     

Aligned and molecularly oriented semihollow ultrafine polymer fiber yarns by a facile method

In this work, aligned and molecularly oriented bone‐like PLLA semihollow fiber yarns were manufactured continuously from an optimized homogeneous polymer‐solvent‐nonsolvent system [PLLA, CH₂Cl₂, and dimethyl formamide (DMF)] by a single capillary electrospinning via self‐bundling technique. Here, it should be emphasized that the self‐bundling electrospinning technique, a very facile electrospinning technique with a grounded needle (which is to induce the self‐bundling of polymer nanofibers at the beginning of electrospinning process), is used for the alignment and molecular orientation of the polymer fiber, and the take‐up speed of the rotating drum for the electrospun fiber yarn collection is very low (0.5 m/s). PLLA can be dissolved in DMF and CH₂Cl₂ mixed solvent with different ratios. By varying the ratios of mixed solvent system, PLLA electrospun semihollow fiber with the porous inner structure and compact shell wall could be formed, the thickness of the shell and the size of inner pores could be adjusted. The results of polarized FTIR and wide angle X‐ray diffraction investigations verified that as‐prepared PLLA semihollow fiber yarns were well‐aligned and molecularly oriented. Both the formation mechanism of semihollow fibers with core‐shell structure and the orientation mechanism of polymer chains within the polymer fibers were all discussed. The as‐prepared self‐bundling electrospun PLLA fiber yarns possessed enhanced mechanical performance compared with the corresponding conventional electrospun PLLA fibrous nonwoven membranes. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1118–1125, 2010     

Assessment of conservative weighting scheme in simulating chemical vapour deposition with trace species

Low‐pressure or ultra‐high vacuum chemical vapour deposition often involves important trace species in both gas‐phase and surface reactions. The conservative weighting scheme (J. Thermophys. Heat Transfer 1996; 10 (4) : 579) has been used to deal with the trace species often involved in some non‐reactive physical processes, which is otherwise considered computationally impossible using the conventional DSMC method. This conservative weighting scheme (CWS) improves greatly the statistical uncertainties by decreasing the weighting factors of trace‐species particles and ensures the conservation of both momentum and energy between two colliding particles with large difference of weighting factors. This CWS is further extended to treat reactive processes for gas‐phase and surface reactions with trace species, which is called extended conservative weighting scheme (ECWS). A single‐cell equilibrium simulation is performed for verifying both the CWS and ECWS in treating trace species. The results of using CWS show that it is most efficient and accurate for weight ratio (trace to non‐trace) equal to or less than 0.01 for flows with two and three species. The results of a single‐cell simulation using ECWS for gas‐phase reaction and surface reactions show that only ECWS can produce acceptable results with reasonable computational time. Copyright © 2003 John Wiley & Sons, Ltd.     

Novel family of triphenylamine‐containing,hole‐transporting,amorphous, aromatic polyamides with stable electrochromic properties

We report the preparation and characterization of a series of novel electrochromic, aromatic poly(amine amide)s with pendent triphenylamine units. The synthesis proceeded via direct phosphorylation polycondensation between a novel diamine, N,N‐bis(4‐aminophenyl)‐N′,N′‐diphenyl‐1,4‐phenylenediamine, and various aromatic dicarboxylic acids. All the poly(amine amide)s were amorphous and readily soluble in many common organic solvents and could be solution‐cast into transparent, tough, and flexible films with good mechanical properties. They exhibited good thermal stability and 10% weight‐loss temperatures above 540 °C. Their glass‐transition temperatures were 263–290 °C. These polymers in N‐methyl‐2‐pyrrolidinone solutions exhibited strong ultraviolet–visible absorption peaks at 307–358 nm and photoluminescence peaks around 532–590 nm in the green region. The hole‐transporting and electrochromic properties were studied with electrochemical and spectroelectrochemical methods. Cyclic voltammograms of poly(amine amide) films prepared by the casting of polymer solutions onto an indium tin oxide coated glass substrate exhibited two reversible oxidation redox couples at 0.65 and 1.03 V versus Ag/AgCl in an acetonitrile solution. All the poly(amine amide)s showed excellent stability with respect to their electrochromic characteristics; the color of the films changed from pale yellow to green and then blue at 0.85 and 1.25 V, respectively. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2085–2098, 2005     

Laser Spectroscopy on the MgH A2Π - X2Σ+ Band System

The A²Π - X²Σ⁺ electronic transition of MgH has been studied by the laser excitation spectroscopy. Some new transitions have been observed for the first time. Rotational parameters of the X and A state have been derived and compared with other experimental values.     

Study of a thermotropic liquid-crystalline polyester at elevated pressures

A thermotropic liquid-crystalline copolyester of 20% hydroxybenzoic acid, 40% isophthalic acid, and 40% hydroquinone polymer was studied at elevated pressures. The characterization techniques at elevated pressures (0–1000 bar) included high-pressure differential thermal analysis and dilatometry; at atmospheric pressure, differential scanning calorimetry, thermal optical analysis, and x-ray analysis were employed. The mechanical properties of the solid specimens prepared at different pressures were studied by compression and dynamic rotation mechanical testing techniques. High-pressure induced a new crystal habit in the solid state and a new mesophase in the melt. These transitions are summarized in a proposed phase diagram. Mechanical tests on the material produced at elevated pressure indicate the possibility of improved properties, implying that the pressure-dependent morphological changes in thermotropic copolyesters could be of practical significance. The finding of a pressure-induced mesophase also confirmed the possibility of extending the range of polymers which might exhibit liquid crystallinity via the application of pressure.     

Silver‐Assisted Chemical Etching on Silicon with Polyvinylpyrrolidone‐Mediated Formation of Silver Dendrites

Metal‐assisted chemical etching (MaCE) on silicon (Si)—mediated by polyvinylpyrrolidone (PVP)—is systematically investigated herein. It is found that the morphologies and crystallographic natures of the grown silver (Ag) dendrites can be significantly modulated, with the presence of PVP in the MaCE process leading to the formation of faceted Ag dendrites preferentially along the (111) crystallographic phase, rather than along the (200) phase. Further explorations of the PVP‐mediated effect on Si etching are also revealed. In contrast to the aligned Si nanowires formed by MaCE without PVP addition, only distributed nanopores with sizes of 200 to 400 nm appear on the Si surfaces in the presence of PVP. The origin of surface polishing on Si in the PVP‐mediated MaCE process can be attributed to the distinct transport pathway of holes supplied by the Ag⁺ ions, where the holes are injected directly into the primary Ag seeds, rather than through Ag dendrites, thus leading to the isotropic etching of the Si surface.     

Ortho‐Quinone Methides as Reactive Intermediates in Asymmetric Brønsted Acid Catalyzed Cycloadditions with Unactivated Alkenes by Exclusive Activation of the Electrophile

An efficient method for the highly enantioselective synthesis of chiral chromanes bearing multiple stereogenic centers was developed. A chiral BINOL‐based N‐triflylphosphoramide proved to be an effective catalyst for the in situ generation of ortho‐quinone methides (o‐QMs) and their subsequent cycloaddition reaction with unactivated alkenes provided chromanes with excellent diastereo‐ and enantioselectivity.