A new VOF‐based numerical scheme for the simulation of fluid flow with free surface. Part II: application to the cavity filling and sloshing problems

Finite element analysis of fluid flow with moving free surface has been performed in 2‐D and 3‐D. The new VOF‐based numerical algorithm that has been proposed by the present authors (Int. J. Numer. Meth. Fluids, submitted) was applied to several 2‐D and 3‐D free surface flow problems. The proposed free surface tracking scheme is based on two numerical tools; the orientation vector to represent the free surface orientation in each cell and the baby‐cell to determine the fluid volume flux at each cell boundary. The proposed numerical algorithm has been applied to 2‐D and 3‐D cavity filling and sloshing problems in order to demonstrate the versatility and effectiveness of the scheme. The proposed numerical algorithm resolved successfully the free surfaces interacting with each other. The simulated results demonstrated applicability of the proposed numerical algorithm to the practical problems of large free surface motion. It has been also demonstrated that the proposed free surface tracking scheme can be easily implemented in any irregular non‐uniform grid systems and can be extended to 3‐D free surface flow problems without additional efforts. Copyright © 2003 John Wiley & Sons, Ltd.     

Investigation of chemometric calibration performance based on different chemical matrix and signal-to-noise ratio.

The chemometric calibration performance was systematically investigated by two parameters (changing the chemical matrix as well as the signal-to-noise ratio) of the NIR (near-infrared) spectrum. Three different analytes (hexane, cyclohexane, toluene) were selected and heptane was used as a solvent. The degree of spectral difference significantly affected the calibration performance. The largest structural difference between the analyte and the solvent provided the best calibration result for a given signal-to-noise ratio. Additionally, the signal-to-noise ratio of the spectra also directly influenced the calibration performance. Overall, the spectral difference and signal-to-noise ratio were the major factors for governing the chemometric calibration performance, especially in the low-concentration range.     

SEQUENTIAL QUADRATIC PROGRAMMING METHODS FOR OPTIMAL CONTROL PROBLEMS WITH STATE CONSTRAINTS

A Kind of direct methods is presented for the solution of optimal control problems with state constraints.These methods are sequential quadratic programming methods.At every iteration a quadratic programming which is obtained by quadratic approximation to Lagrangian function and Linear approximations to constraints is solved to get a search direction for a merit function.The merit function is formulated by augmenting the Lagrangian funetion with a penalty term.A line search is carried out along the search direction to determine a step length such that the merit function is decreased.The methods presented in this paper include continuous sequential quadratic programming methods and discreate sequential quadrade programming methods.     

Synthesis of 5‐Radioiodoarabinosyl Uridine Analog for Probing the HSV‐1 Thymidine Kinase Gene

Tumor cells transduced with herpes simplex virus thymidine kinase gene have been intensively applied to the field of positron emission tomography via imaging of its substrate. As a pilot synthesis approach, a facile preparation of 5‐[¹²⁵I] iodoarabinosyl uridine starting from commercially available uridine is reported herein.     

Preparation of Fe–Si–B–Nb amorphous powder cores with excellent high-frequency magnetic properties

FeSiBNb amorphous powder cores were prepared with the amorphous powder by gas atomization and subsequent hot pressing of resulting powder after creating oxide layers on the amorphous powder. Fully amorphous FeSiBNb powders with good soft magnetic properties were successfully obtained in the particle size range below 100 μm. FeSiBNb amorphous powder cores exhibit stable permeability up to 10 MHz, showing excellent high-frequency characteristics.     

Singlewall carbon nanotubes covered with polystyrene nanoparticles by in‐situ miniemulsion polymerization

This work is to make carbon nanotubes dispersible in both water and organic solvents without oxidation and cutting nanotube threads. Polystyrene‐singlewall carbon nanotube (PS‐SWNT) composites were prepared with three different methods: miniemulsion polymerization, conventional emulsion polymerization, and mixing SWNT with PS latex. The two factors, crosslinking and surface coverage of PS are important factors for the mechanical and electrical properties, including dispersion states of SWNT in various solvents. The PS‐SWNT composite prepared via a conventional emulsion polymerization showed SWNT bundles entirely covered with PS, whereas the PS‐SWNT composite prepared via a miniemulsion polymerization showed SWNT partially covered with crosslinked PS nanoparticles. The method of mixing SWNTs with PS latex did not show the well dispersed state of carbon nanotubes because PS was not crosslinked and was dissolved in a solvent, and nanotubes separated from PS precipitated. So the PS nanoparticle‐SWNT composite had lower electrical resistance, and higher mechanical strength than the other composites made by the latter two methods. As the amount of SWNT increases, the bare surface area of SWNT increases and the electrical conductivity increases in the composite made by the miniemulsion polymerization. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 573–584, 2006     

Cascade Grating Structure for Increasing the Channel Number on Holographic Demultiplexer

The expansion capability of the channel number in the optical demultiplexer using two cascaded photopolymer volume gratings is reported. It could be accomplished by designing of two gratings with different spectral range. As a result of the experiment, a 0.4-nm-spaced 130-channel demultiplexer with the channel uniformity of 3.5 dB, the 3 riB-bandwidth of 0.12nm, and the channel crosstalk of-20 dB is experimentally demonstrated.     

A Dynamic location problem for graphs

We introduce a class of optimization problems, calleddynamic location problems, involving the processing of requests that occur sequentially at the nodes of a graphG. This leads to the definition of a new parameter of graphs, called the window indexWX(G), that measures how large a window into the future is needed to solve every instance of the dynamic location problem onG optimally on-line. We completely characterize this parameter:WX(G)k if and only ifG is a weak retract of a product of complete graphs of size at mostk. As a byproduct, we obtain two (polynomially recognizable) structural characterizations of such graphs, extending a result of Bandelt.