Effects of Post-Thermal Treatment on Quality of SiC Grown by PVT Method

We report the effects of post-thermal treatment on the quality of 2-inch 6H-SiC wafer cut from a crystal boule grown by physical vapour transportation method. The full widths at half maximum of x-ray diffraction rocking curves measured on sites across the 2-inch wafer become narrower, indicating the quality improvement after a three-step post-thermal treatment. It is found that the most common defects such as micropipes and inclusions can be significantly reduced after the treatment. Our results show that the post-thermal treatment is an effective route to improve the quality of SiC single crystals.     

用二维复式晶格有限集团模型计算聚乙炔的电子结构

以二维复式晶格作为有限系统的集团模型,在紧束缚近似下,计算了π电子在最近邻及次近邻跳跃集团的态密度.讨论了不同结构参数对态密度及带宽的影响.     

Poly[[diaqua(N,N‐dimethylformamide‐κO)manganese(II)]‐μ3‐sulfato]

In the title complex, [Mn(SO₄)(C₃H₇NO)(H₂O)₂]_n, each Mn^II ion has a distorted octahedral geometry formed by three O atoms of three different sulfate groups, one O atom of a dimethylformamide ligand and two water molecules. The sulfate groups act as tridentate bridging ligands connecting the Mn^II ions into a two‐dimensional layer structure which can be regraded as a 4.8² network.     

纯锆上离子注入钇和镧后的表面分析

用金属蒸汽真空弧源，以40kV加速电压对纯锆样品分别进行了10¹⁶—10¹⁷/cm²的钇、镧离子注入，注入温度约为130℃.然后对注入样品进行表面分析.x射线光电子能谱分析表明，注入的钇以Y₂O₃形式存在，镧以La₂O₃形式存在.俄歇电子能谱表明，纯锆基体表面的氧化膜厚度随着离子注入剂量的增加而增加，当离子注入剂量达到10¹⁷/cm²时，氧化膜的厚度达到了最大值.卢瑟福背散射显示镧层的厚度约为30nm，同时直接观察到当离子注入剂量为(La+Y)10¹⁷/cm²时，纯锆样品表面发生了严重的溅射. 关键词： 纯锆 钇和镧离子共注入 卢瑟福背散射 x射线光电子能谱     

中立型时滞差分方程的振性与正解存在性

本文研究了一类中立型时滞差分方程的振动性和正解存在性，获得了该方程所有解振动的“Sharp”条件及存在正解的一个充分条件．     

混合纤芯光子晶体光纤超平坦色散的研究

利用平面波展开法，系统地研究了一种具有混合纤芯结构的光子晶体光纤的色散特性. 数值计算结果表明，通过优化结构参量，这种新型结构的光子晶体光纤在通信窗口1.55 μm 附近可以获得带宽超过800 nm的超平坦色散区域（色散曲线的变化范围不超过 ±0.6 ps·km－1·nm－1）.     

具有突变结构开放腔的矩阵分析

利用模式展开与场匹配原理，建立了突变波导的散射矩阵(S参数矩阵)，在此基础上分析研究了具有突变结构的波导开放式谐振腔，并由矩阵级联建立了开放腔总的S参数矩阵.通过Matlab编制计算程序对具有多级突变结构的开放式输出腔进行了数值计算和分析，并通过与实验数据和软件模拟的结果比较对该方法得到的数据结果进行了验证. 关键词： 回旋管 开放式谐振腔 突变结构 S参数矩阵     

Investigation of sulfonated poly(ether ether ketone sulfone)/heteropolyacid composite membranes for high temperature fuel cell applications

The sulfonated poly(ether ether ketone sulfone) (SPEEKS)/heteropolyacid (HPA) composite membranes with different HPA content in SPEEKS copolymers matrix with different degree of sulfonation (DS) were investigated for high temperature proton exchange membrane fuel cells. Composite membranes were characterized by Fourier transfer infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). FTIR band shifts suggested that the sulfonic acid groups on the copolymer backbone strongly interact with HPA particles. SEM pictures showed that the HPA particles were uniformly distributed throughout the SPEEKS membranes matrix and particle sizes decreased with the increment of copolymers' DS. The holes were not found in SPEEKS‐4/HPA30 (consisting of 70% SPEEKS copolymers with DS = 0.8 and 30% HPA) composite membrane after composite membranes were treated with boiling water for 24 h. Thermal stabilities of the composite membranes were better than those of pure sulfonated copolymers membranes. Although the composite membranes possessed lower water uptake, it exhibited higher proton conductivity for SPEEKS‐4/HPA30 especially at high temperature (above 100 °C). Its proton conductivity linearly increased from 0.068 S/cm at 25 °C to 0.095 S/cm at 120 °C, which was higher than 0.06 S/cm of Nafion 117. In contrast, proton conductivity of pure SPEEKS‐4 membrane only increased from 0.062 S/cm at 25 °C to 0.078 S/cm at 80 °C. At 120 °C, proton conductivity decreased to poor 0.073 S/cm. The result indicated that composite membranes exhibited high proton conductivity at high temperature. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1967–1978, 2006     

聚甲基丙烯酸甲酯掺杂Ce3+的飞秒激光三维信息存储

用飞秒激光(200 fs,1 kHz,800 nm)脉冲在掺杂稀土离子Ce3 的聚甲基丙烯酸甲酯(PMMA)膜中进行了光存储实验研究,包括对样品的吸收光谱、激光照射前后的电子旋转共振(Electron spin resonance,ESR)光谱的测量和讨论。结果表明掺杂稀土离子Ce3 的聚甲基丙烯酸甲酯膜具有较低的写入阈值,有利于高速、并行的三维光存储。实验结果采用传统光学显微镜并行读出。给出了四层存储结果(点间距和层间距分别是4μm和16μm),并讨论了脉冲能量的大小对空腔尺寸的影响,进行高密度存储时,在保证读出信号灰度值足够大的情况下,应选择尽量小的激光脉冲写入能量。实验结果表明这种材料可以应用于三维光信息存储。