Synthesis of a eta 2-2,3-diphosphabutadiene complex of zerovalent platinum from the corresponding eta 2-phosphaalkyne complex

Hydrozirconation of the eta 2-phosphaalkyne complex [Pt(dppe)(eta 2-tBuCP)] with [ZrHCl(eta 5-C5H5)2], followed by treatment with the chlorophosphaalkene ClP=C(SiMe3)2 affords the eta 2-2,3-diphosphabutadiene complex [Pt(dppe)(eta 2-tBuC(H)=PP=C(SiMe3)2]. In the presence of [Pt(PPh3)2] the latter undergoes an addition reaction with water to afford the structurally characterised Pt(II) complex [Pt(dppe)(tBuCH2P(O)HPC(SiMe3)2].     

Thermal conductivity of lightweight aggregate based on coal fly ash

The article presents the results of physical and chemical properties of lightweight aggregates (LWA) obtained by the thermal treatments of raw composition based on fly ash, supplied by electric plants from Serbia. The production process of LWA consists of raw material preparation, plastic shaping?Cextrusion, granulation, and thermal treatment at three temperatures: 1100, 1150, and 1200?°C. The final firing temperature (T?=?1150?°C) is chosen based on the mechanical and physical properties of the designed aggregates. The particle-size distribution of the LWAs is unimodal (d????16?mm) while the density value varies from 0.98 to 1.99?g/cm³. The water absorption values are determined by use of two methods: 24?h of soaking in cold water and 5?h of boiling. The thermal conductivity of unbound, fired LWA particles is determined by measuring the amount of axially transferred heat in the stationary state. The obtained value of the LWA thermal conductivity (???=?0.0872?W/mK, T?=?1150?°C) is suitable for the production of structural concrete blocks with improved thermal insulating properties. Because of their high-porosity and -compressive strength values, the designed LWA could be used instead of the conventional aggregates in the production of concrete blocks. Consequently, a real valorization of the waste material such as fly ash in Serbia was established.     

Consecutive customer losses in oscillating GIX/M//n systems with state dependent services rates

We address the probability that k or more Consecutive Customer Losses take place during a busy period of a queue, the so-called k-CCL probability, for oscillating GI ^X /M//n systems with state dependent services rates, also denoted as GI ^X /M(m)−M(m)//n systems, in which the service rates oscillate between two forms according to the evolution of the number of customers in the system. We derive an efficient algorithm to compute k-CCL probabilities in these systems starting with an arbitrary number of customers in the system that involves solving a linear system of equations. The results derived are illustrated for specific sets of parameters.     

Consecutive customer losses in regular and oscillating <Emphasis Type="Italic">M</Emphasis><Superscript><Emphasis Type="Italic">X</Emphasis></Superscript>/<Emphasis Type="Italic">G</Emphasis>/1/<Emphasis Type="Italic">n</Emphasis> systems

We derive fast recursions to compute the probability that k or more consecutive customer losses take place during a busy period of a queue, the so called k-CCL probability, for regular and oscillating M ^X /G/1/n systems.     

A New Indirect Electroanalytical Method to Monitor the Contamination of Natural Waters with 4‐Nitrophenol Using Multiwall Carbon Nanotubes

The electrochemical detection of the hazardous pollutant 4‐nitrophenol (4‐NP) at low potentials, in order to avoid matrix interferences, is an important research challenge. This study describes the development, electrochemical characterization and utilization of a multiwall carbon nanotube (MWCNT) film electrode for the quantitative determination of 4‐NP in natural water. Electrochemical impedance spectroscopy measurements showed that the modified surface exhibits a decrease of ca. 13 times in the charge transfer resistance when compared with a bare glassy carbon (GC) surface. Voltammetric experiments showed the possibility to oxidize a hydroxylamine layer (produced by the electrochemical reduction of 4‐NP on the GC/MWNCT surface) in a potential region which is approximately 700 mV less positive than that needed to oxidize 4‐NP, thus minimizing the interference of matrix components. The limit of detection for 4‐NP obtained using square‐wave voltammetry (0.12 μmol L^?1) was lower than the value advised by EPA. A natural water sample from a dam located in São Carlos (Brazil) was spiked with 4‐NP and analyzed by the standard addition method using the GC/MWCNT electrode, without any further purification step. The recovery procedure yielded a value of 96.5% for such sample, thus confirming the suitability of the developed method to determine 4‐NP in natural water samples. The electrochemical determination was compared with that obtained by HPLC with UV‐vis detection.     

Design of 1060nm tapered lasers with separate contacts

Numerical simulations have been used to produce advanced designs of high brightness gain guided tapered lasers emitting at 1,060 nm. The simulations predicted high modulation efficiency in devices with separate contacts and low front facet reflectivity. The devices fabricated following these design guidelines demonstrated high internal quantum efficiency in Broad Area lasers, output power of 3 W with good beam quality in tapered lasers with common contacts, and modulation efficiencies up to 20 W/A in tapered lasers with separate contacts, in good agreement with the simulation predictions.     

Preparation and characterization of KTa0.9Fe0.1O3– δ perovskite electrodes

The effect of the partial substitution of tantalum by iron on the structural and electrical properties of the KTaO₃ perovskite-type oxide powders has been studied. The powders were prepared by the standard ceramic method, and the respective structural characterization performed by X-ray powder diffraction. From the synthesized oxide samples, iron-coated electrodes were fabricated and tested as the anode for the oxygen evolution reaction in alkaline medium. An estimation of the electrode's capacity has been calculated from the charging currents and the corresponding roughness factor evaluated. The electrocatalytic activity/stability of the oxide electrodes in alkaline solutions has been analysed through the kinetic parameters. Electronic Publication