Novel fixed‐site–carrier polyvinylamine membrane for carbon dioxide capture

Fixed‐site–carrier membranes were prepared for the facilitated transport of CO₂ by casting polyvinylamine (PVAm) on various supports, such as poly(ether sulfone) (PES), polyacrylonitrile (PAN), cellulose acetate (CA), and polysulfone (PSO). The cast PVAm on the support was crosslinked by various methods with glutaraldehyde, hydrochloric acid, sulfuric acid, and ammonium fluoride. Among the membranes tested, the PVAm cast on polysulfone and crosslinked by ammonium fluoride showed the highest selectivity of CO₂ over CH₄ (>1000). The permeance of CO₂ was then measured to be 0.014 m³ (STP)/(m² bar h) for a 20 μm thick membrane. The effect of the molecular weight of PVAm and feed pressure on the permeance was also investigated. The selectivity increased remarkably with increasing molecular weight and decreased slightly with increased pressure in the range of 1 to 4 bar. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4326–4336, 2004     

Pressure and temperature dependence of the gas‐transport properties of dense poly[2,6‐toluene‐2,2‐bis(3,4‐dicarboxylphenyl)hexafluoropropane diimide] membranes

The gas‐transport properties of poly[2,6‐toluene‐2,2‐bis(3,4‐dicarboxylphenyl)hexafluoropropane diimide] (6FDA‐2,6‐DAT) have been investigated. The sorption behavior of dense 6FDA‐2,6‐DAT membranes is well described by the dual‐mode sorption model and has certain relationships with the critical temperatures of the penetrants. The solubility coefficient decreases with an increase in either the pressure or temperature. The temperature dependence of the diffusivity coefficient increases with an increase in the penetrant size, as the order of the activation energy for the diffusion jump is CH₄ > N₂ > O₂ > CO₂. Also, the average diffusion coefficient increases with increasing pressure for all the gases tested. As a combined contribution from sorption and diffusion, permeability decreases with increases in the pressure and the kinetic diameter of the penetrant molecules. Even up to 32.7 atm, no plasticization phenomenon can be observed on flat dense 6FDA‐2,6‐DAT membranes from their permeability–pressure curves. However, just as for other gases, the absolute value of the heat of sorption of CO₂ decreases with increasing pressure at a low‐pressure range, but the trend changes when the feed pressure is greater than 10 atm. This implies that CO₂‐induced plasticization may occur and reduce the positive enthalpy required to create a site into which a penetrant can be sorbed. Therefore, a better diagnosis of the inherent threshold pressure for the plasticization of a glassy polymer membrane may involve examining the absolute value of the heat of sorption as a function of pressure and identifying the turning point at which the gradient of the absolute value of the heat of sorption against pressure turns from a negative value to a positive one. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 354–364, 2004     

Relationship between the dynamic softening transition and wet sliding friction of elastomer compounds

For properly chosen elastomer compounds, thermorheological characterization is combined with an examination of the variation of the wet sliding friction with temperature. A conceptual argument leads to the assumption that the wet sliding friction should maximize at the energy dissipation peak associated with the dynamic softening transition at a characteristic frequency determined by the sliding speed and the effective smallest surface asperity scale. The dynamic softening transition is characterized with the peak in tan δ/G′ⁿ, where tan δ is the loss tangent, G′ is the elastic modulus, and n is a constant between 0 and 1. The William–Landel–Ferry transform is uncritically applied for extrapolating the position of the peak in tan δ/G′ⁿ at high frequencies. Even based on the criterion of tan δ, the results obtained on a concrete surface indicate that the effective smallest asperity scale is of order of 100 μm. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2467–2478, 2004     

Differential scanning calorimetry and thermogravimetric analysis investigation of the thermal properties and degradation of some radiation‐grafted films and membranes

The influence of irradiation and grafting on the crystallinity of three base polymers has been investigated with differential scanning calorimetry. Grafting has the largest effect on the base polymer crystallinity and results in a reduction of the crystallinity. The thermal degradation of the base polymers and grafted films has been investigated with thermogravimetric analysis. The extent of the fluorination of the base polymer, the irradiation method, and the graft level all influence the thermal degradation and its activation energy. It is proposed that the variation of the chain lengths of the grafted polystyrene chains is actually a primary underlying factor responsible for the influence of these various parameters on the degradation process. The first results of a comparative thermal analysis of some fuel‐cell membranes are also presented, and the promise and shortcomings of this method are discussed. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2612–2624, 2004     

Estimation of kinetics parameters for the adsorption of human serum albumin onto hydroxyapatite-modified silver electrodes by piezoelectric quartz crystal impedance analysis.

The adsorption of human serum albumin onto hydroxyapatite-modified silver electrodes has been in situ investigated by utilizing the piezoelectric quartz crystal impedance technique. The changes of equivalent circuit parameters were used to interpret the adsorption process. A kinetic model of two consecutive steps was derived to describe the process and compared with a first-order kinetic model by using residual analysis. The experimental data of frequency shift fitted to the model and kinetics parameters, k1, k2, psi1, psi2 and qr, were obtained. All fitted results were in reasonable agreement with the corresponding experimental results. Two adsorption constants (7.19 kJ mol(-1) and 22.89 kJ mol(-1)) were calculated according to the Arrhenius formula.     

掺氢与激励电路对钡蒸气激光输出特性的影响

对用Blumlein电路放电激励的钡蒸气激光在掺氢和不掺氢时的输出特性进行了实验研究.结果表明，用掺氢1.5%的氖气作缓冲气体能使激光功率增加近2倍.在此基础上，进一步比较了相互作用电路与Blumlein电路时钡蒸气激光的输出特性，发现相互作用电路能显著提高钡蒸气激光的输出功率和效率，获得了3W最大功率和0.4%效率的1.5μm波长激光输出.测量并分析了各工作参量与激光功率之间的关系，定性解释了掺氢与相互作用电路的作用机理 . 关键词： Blumlein电路 相互作用电路 掺氢 钡蒸气激光     

Yb:FAP和Yb:C_3S_2-FAP晶体光谱的温度特性和选择激发

报导了Yb :FAP和Yb :C3S2 _FAP晶体在不同温度下的吸收光谱和荧光光谱实验结果 ,研究发现由于电子_声子近共振耦合作用 ,Yb :FAP和Yb :C3S2 _FAP晶体均存在有明显的振动谱 ,Yb :FAP晶体的零声子线在低温下还劈裂为相差 10cm- 1 的两条线 .采用激光选择激发技术研究了Yb3 离子在FAP和C3S2 _FAP晶体中的格位特征 ,结果表明Yb3 离子在这两种基质中都只占据Ca(Ⅱ )格位 ,但由于CaF2 的挥发 ,导致了Ca(Ⅱ )格位的局部畸变 .     

ns脉冲激光对K9玻璃的破坏实验

 采用高速PIN光电探测器和高带宽的数字存储示波器，实时检测透射光脉冲和散射光脉冲的变化特征，并将之用作材料破坏的光学判据，测量得到K9玻璃在1.06μm纳秒脉冲激光作用下的能量损伤阈值约18mJ，相应的能量密度阈值为1.0kJ/cm²。通过分析透射光脉冲和散射光脉冲的特征，给出了材料的破坏时刻，并推断出K9玻璃所能承受的极限光强为10¹⁵W/m²。研究了能量透过率与泵浦能量的关系，并初步探讨了透明材料的破坏机理。结果表明：在多纵模激光的作用下，透明光学材料破坏是电离击穿与自聚焦效应综合作用的结果。     

连续照明时成像对比度与气象条件的关系

 通过同轴激光连续照明成像模型分析了大气后向散射对成像对比度的影响，得出了考虑散射因素时成像对比度的计算公式。基于不同气象条件下大气粒子散射特点，讨论了霾和雾两种不同天气时成像对比度随照明距离的变化规律，并与实验结果进行了对比，计算结果与实验吻合较好。     

喷气Z箍缩内爆等离子体的雪铲模型

 在喷气Z pinch内爆等离子体研究中，雪铲模型是一种常用的、比较简单的物理模型。根据实验中提供的电流波形，负载线质量和初始半径，可以通过雪铲模型来估算内爆到心的时刻。根据一维运动方程和不同构形下的解析解以及部分实验结果相结合，讨论了雪铲模型的适用范围。数值计算的内爆时间和实验（Gamble II, Double EAGLE, BLACKJACK 5）测量值符合得较好。结果表明，雪铲模型在喷气Z pinch实验的负载优化设计研究中是很有参考价值的方法。