EPR evidence for 17O− on molybdenum oxide supported by silica-gel

The EPR spectrum of ¹⁷O^? on partially reduced molybdenum oxide supported on silica-gel has been observed following adsorption of N₂O at room temperature. The spectrum is chracterized by g_⊥=2.019 and g_|=2.002 with a_|¹⁷O^?=96±1 G and a_|⁹⁵MO,⁹⁷MO=7.5±0.5 G. The O ^?ion appears to undergo exchange with oxide ions at the surface.     

Characteristics of immunosorbents used as a new approach to selective solid-phase extraction in environmental analysis

Summary The trace-level determination of organic pollutants in complex matrices is difficult and often not reliable because theccurrent extraction procedures are non-selective. New extraction sorbents involving antigen-antibody interactions, called immunosorbents (ISs), have been synthesised in order to trap a group of structurally related pollutants. The IS capacity is always high for the analyte-antigen used to make the antibodies, but can be low for some related compounds. In this work, we show the relationship that exists between capacity, break-through volume and recovery of analytes because of the competition between the structurally related compounds for antibody sites. Breakthrough due to the overloading of the column should be avoided because calibration curves are no longer linear. The capacity of two ISs, one made for trapping the triazine pesticide group and the second for the phenylurea, group, have been optimised by selecting silica with 50 nm pore size. Calibration curves are linear for all the compounds in a mixture of ten phenylureas up to a concentration of 5 to 10 μg L⁻¹ for each compound when handling 50 mL water samples through a precolumn packed with 0.22 g of IS. Under these conditions, reliable quantitative results are obtained because calibration curves are similar when compounds are alone or in a mixture. Application to the clean-up of soil extracts illustrates the high selectivity and the high potential of these new sorbents in environmental analysis. Presented at the 21^st ISC held in Stuttgart, Germany, 15^th–20^th September, 1996     

Quantitative effect of nonionic surfactant partitioning on the hydrophile-lipophile balance temperature

Phase behaviors of water/nonionic surfactants/isooctane systems are determined experimentally in temperature-global surfactant concentration diagrams. The surfactants are monodistributed polyoxyethylene glycol n-dodecyl ether. They are used as model mixtures of two, three, or five compounds or as constituents of a commercial surfactant. It is found that the phase diagrams of these systems are bent gradually toward the highest temperatures as the global surfactant concentration decreases. Each phase diagram is well-characterized by the curve of the HLB (hydrophile-lipophile balance) temperature versus the global surfactant concentration. For any fixed global surfactant concentration, this temperature is the middle temperature of the three-phase region; it can be calculated from an additive rule of the HLB temperatures of the surfactants weighted by their mole fractions at the water/oil interface. These mole fractions are determined through the pseudophase model using surfactant partitioning. Calculations require the knowledge of the critical micelle concentration, the partition coefficient between water and oil, and the HLB temperature of each surfactant of the mixture. This treatment can be used to correctly predict the variation of the HLB temperatures of the surfactant mixtures studied versus the global surfactant concentration. Furthermore, these calculations show that the observed curvature of the phase diagrams at the lowest global concentrations is due to the most favorable partitioning toward the oil of the lowest ethoxylated surfactant molecules.     

Tracking the optical mass centroid of single electroactive nanoparticles reveals the electrochemically inactive zone

The inevitable microstructural defects, including cracks, grain boundaries and cavities, make a portion of the material inaccessible to electrons and ions, becoming the incentives for electrochemically inactive zones in single entity. Herein, we introduced dark field microscopy to study the variation of scattering spectrum and optical mass centroid (OMC) of single Prussian blue nanoparticles during electrochemical reaction. The “dark zone” embedded in a single electroactive nanoparticle resulted in the incomplete reaction, and consequently led to the misalignment of OMC for different electrochemical intermediate states. We further revealed the dark zones such as lattice defects in the same entity, which were externally manifested as the fixed pathway for OMC for the migration of potassium ions. This method opens up enormous potentiality to optically access the heterogeneous intraparticle dark zones, with implications for evaluating the crystallinity and electrochemical recyclability of single electroactive nano-objects.

The schematic of single cubic-shaped Prussian blue (PB) mesocrystals formed by the oriented aggregation of small nanocrystals. The dark-field images of single PB nanoparticle at PB and Prussian white (PW) states, respectively.     

4,4′‐Bipyridyl N,N′‐dioxide–3‐hydroxy‐2‐naphthoic acid (1/2)

4,4′‐Bipyridyl N,N′‐dioxide crystallizes with 3‐hydr­oxy‐2‐naphthoic acid to give a centrosymmetric three‐component adduct, C₁₀H₈N₂O₂·2C₁₁H₈O₃, which is engineered into a two‐dimensional layer structure by two kinds of π–π inter­actions. Weak C—H⋯O inter­actions further link the two‐dimensional structure into a three‐dimensional structure.     

Etude de phosphates condenses diagramme d’equilibre du systeme AgPO3−Pr(PO3)3 Données sur AgPr(PO3)4

The AgPO₃?Pr(PO₃)₃ system has been studied for the first time by differential thermal analysis, X-ray diffraction and IR spectroscopy. The system shows one compound AgPr(PO₃)₄ which melts in a peritectic decomposition at 1069 K. An eutectic appears at 761 K. AgPr(PO₃)₄ belongs to the monoclinic system with space group P2_t/c,Z=4. The parameters of the unit cell are:a=12.000(9),b=13.177(4),c=7.046(5) Å and β=123^o,81(6),Z=4. Its IR absorption spectrum is typical of chain phosphates.     

Fluorescent polymer cubosomes and hexosomes with aggregation-induced emission

Fluorescent polymer cubosomes and hexosomes with aggregation-induced emission (AIE) were prepared from amphiphilic block copolymers PEG-b-PTPEMA where the hydrophobic block PTPEMA was a polymethacrylate with tetraphenylethene (TPE) as the AIE side group. Four highly asymmetric block copolymers with hydrophilic block weight ratio f_PEG ≤ 20% were synthesized. Cubosomes and hexosomes with strong fluorescence emission were obtained by nanoprecipitation of polymers with f_PEG < 9% in dioxane/water and THF/water systems. Their ordered internal structures were studied by electron microscopy (cryo-EM, SEM and TEM) and the X-ray scattering technique (SAXS). To elucidate the formation mechanisms of these inverted colloids, other parameters influencing the morphologies, like the water content during self-assembly and the organic solvent composition, were also investigated. This study not only inspires people to design novel building blocks for the preparation of functional cubosomes and hexosomes, but also presents the first AIE fluorescent polymer cubosome and hexosome with potential applications in bio-related fields.

Fluorescent Im$\bar{3}$m cubosome and P6mm hexosome with aggregation-induced emission (AIE) were reported, which were formed by amphiphilic block copolymers PEG-b-PTPEMA. The length of hydrophobic block PTPEMA was adjusted to control morphology formation.     

Large‐scale extrusion processing and characterization of hybrid nylon‐6/SiO2 nanocomposites

Solution impregnations, pulltrusion and film stacking are widely used methods to prepare thermoplastic composite materials. Extruders are used to melt the polymer and to incorporate fibers into the polymer in order to modify physical properties. In this article, the compounding of colloidal silica nanoparticles filled polyamide‐6 (PA‐6) is achieved using a twin‐screw extruder, which has a significant market share due to its low cost and easy maintenance. The experiments were performed at 250 rpm and the bulk throughput was 6 kg h^?1 with a pump pressure of 30 bars. The composites were characterized with nuclear magnetic resonance (NMR), wide angle X‐ray diffraction (WAXD), differential scanning calorimetry (DSC) and transmission electron microscopy (TEM). As determined by WAXD, the PA‐6 showed higher amounts of γ‐phase when compared to other synthesis methods such as in situ polymerization. TEM pictures showed that the silica particles aggregated nevertheless, upon addition of 14% (w/w) silica the E‐modulus increased from 2.7 to 3.9 GPa indicating that an effective mechanical coupling with the polymer was achieved. The behavior, illustrated with dynamic mechanical analysis (DMA) curves, indicated that in general when a filled system is compared to unfilled material, the values of the moduli (E′ and E″) increased and tan δ decreased. Determination of molecular mass distribution of the samples by means of size exclusion chromatography (SEC) coupled to a refractive index (RI), viscosity (DV) and light scattering (LS) detector revealed that the addition of silica did not decrease the average molecular weight of the polymer matrix, which is of importance for composite applications. Copyright © 2004 John Wiley & Sons, Ltd.     

Synthesis and characterization of active ester-functionalized polypyrrole-silica nanoparticles: application to the covalent attachment of proteins

Novel ester-functionalized polypyrrole-silica nanocomposite particles were prepared by oxidative copolymerization of pyrrole and N-succinimidyl ester pyrrole (50/50% initial concentrations), using FeCl3 in the presence of ultrafine silica nanoparticles (20 nm diameter). The N-succinimidyl ester pyrrole monomer was prepared in aqueous solution using 1-(2-carboxyethylpyrrole) and N-hydroxysuccinimide in the presence of 1-ethyl-3-(3-dimethylaminopropyl) carbodiimide. The resulting nanocomposites (N-succinimidyl ester polypyrrole-silica) are raspberry-shaped agglomerates of silica sol particles "glued" together by the insoluble poly(pyrrole-co-N-succinimidyl pyrrole). The N-succinimidyl ester polypyrrole-silica particles were characterized in terms of their size, density, copolymer content, and polydispersity. Scanning electron microscopy and disk centrifuge sedimentometry confirmed that the nanocomposite particles had narrow size distributions. X-ray photoelectron spectroscopy analysis indicated a silica-rich surface and a high surface concentration of N-succinimidyl ester groups. These nanoparticles exhibited good long-term dispersion stability. The chemical stability of the ester functions in aqueous media after several weeks of storage was monitored by FTIR spectroscopy. The functionalized nanocomposites were tested as bioadsorbents of human serum albumin (HSA). The very high amount of immobilized HSA determined by UV-visible spectroscopy is believed to be due to covalent binding. Incubation of the HSA-grafted nanocomposite with anti-HSA resulted in immediate flocculation, an indication that they are alternative candidates for visual diagnostic assays.     

Ring-opening of unsymmetrical 1,2-dioxines using cobalt(II) salen complexes

The regioselectivity of the metal-catalyzed ring opening of unsymmetrical 1,2-dioxines to cis-gamma-hydroxyenones was investigated using two different Co(II) salen complexes. Regioselectivity was determined by direct examination of the enone ratios and by derivitization with a stabilized phosphorus ylide. The steric influence of the substituents on the 1,2-dioxine was the primary influence on regioselectivity. Temperature played little role; however, solvent and selection of Co(II) complex could be used to mildly influence the outcome of the rearrangement for selected substrates. The origins of the selectivity for the reaction are discussed.