Correlation between the Mechanical Properties and the Amount of Desorbed Water for Composites Based on Low-Density Polyethylene and Linen Yarn Production Waste

The effect of the amount of desorbed water on the mechanical properties of composites based on low-density polyethylene and linen yarn production waste (LW) is analyzed by statistical methods. It is shown that the amount of absorbed water decreases during the desorption process at room temperature both for specimens modified and unmodified with diphenylmethane diisocyanate (DIC.) The most sensitive to the action of water is the elastic modulus, which decreases considerably under the effect of water and is fully restored in the desorption process. The tensile strain also increases with the amount of absorbed water. It is found that the elastic modulus of the unmodified composite correlates linearly with the amount of desorbed water. Between the amount of desorbed water and the tensile strain, as well the specific work of deformation, a negative linear correlation is revealed. After water desorption, all strength and deformation characteristics of both the modified and unmodified composites are fully recovered.__________Translated from Mekhanika Kompozitnykh Materialov, Vol. 41, No. 4, pp. 515–524, July–August, 2005.     

Restrictions of Quadratic Forms to Lagrangian Planes,Quadratic Matrix Equations,and Gyroscopic Stabilization

We discuss the symplectic geometry of linear Hamiltonian systems with nondegenerate Hamiltonians. These systems can be reduced to linear second-order differential equations characteristic of linear oscillation theory. This reduction is related to the problem on the signatures of restrictions of quadratic forms to Lagrangian planes. We study vortex symplectic planes invariant with respect to linear Hamiltonian systems. These planes are determined by the solutions of quadratic matrix equations of a special form. New conditions for gyroscopic stabilization are found.     

Investigation of organic impurities adsorbed on and incorporated into electroplated copper layers

At room temperature electroplated copper layers exhibit changes in resistivity, residual stress, and microstructure. This process, known as self-annealing, is intimately linked to the release of organic impurities, which stem from the incorporation of organic additives into the Cu layer in the course of the electroplating process. The behavior of these impurities during self-annealing, represented by the carbon content, could be detected by analytical radio frequency glow discharge optical emission spectrometry (GD-OES) and carrier gas hot extraction (CGHE). The precondition of a quantitative determination is a surface cleaning procedure to remove adsorbed organics from the copper surface. It was observed that at first almost all impurities have to leave the Cu metallization before an accelerated abnormal grain growth can start. The small amount of remaining organic species after self-annealing could be quantified by both examination techniques, GD-OES and CGHE.     

Post deposition purification of PTCDA thin films

The decomposition of perylene-3,4,9,10-tetracarboxylic dianhydride (PTCDA) molecules during evaporation of unpurified raw material in ultra high vacuum was studied. The fragments were identified by mass spectrometry and the influence of these fragments and further contaminations of the raw material on the electronic structure of PTCDA thin films was measured by photoemission spectroscopy. Annealing of contaminated PTCDA films was tested as cheap and easy to perform method for (partial) post deposition purification of the contaminated films.     

Rietveld refinement of CdSe phases annealed under argon atmosphere

Hexagonal and cubic cadmium selenide were prepared from a chemical route by using cadmium chloride and potassium selenium hydride obtained from reaction of selenium powder and potassium boron hydride. The product obtained was thermally treated under argon flux at 300, 500 and 600 °C for 2 h and characterized by X-ray photoelectron spectroscopy and X-ray diffraction. The X-ray diffraction data were refined by Rietveld method and the structural parameters were determined for the phases of each annealed samples. At 300 °C five phases were identified: Cubic and hexagonal cadmium selenides and the contaminants: Potassium chloride, boron oxide and cadmium boron oxide. At 500 and 600 °C only the hexagonal cadmium selenide phase was identified besides the other above mentioned contaminant.     

Nanoclusteration of DNA with dendronized polymer in terms of free energy

A thermodynamic cycle for the nanoclusteration between DNA and dendronized polymer is proposed and electrostatic free energies of a series of DNA- dendronized polymer nanoclusteration processes are calculated. The free energies for assembling fixed charges and mobile ions, and the bending energies of the DNA chain wrapped around the dendronized polymer are taken into consideration. The free energies of nanoclusteration are calculated for a number of nanoclusters with different conformations at constant temperature and constant ionic strength. The effects of temperature and ionic strength on the free energy of nanoclusteration and stability of their conformations are also investigated.     

Zur Analyse der Frauenmilch

Ohne Zusammenfassung