首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 78 毫秒
1.
采用在苯乙烯 (St)悬浮聚合过程中滴加甲基丙烯酸甲酯 (MMA)乳液聚合组分的悬浮 乳液复合聚合方法 ,制备大粒径聚苯乙烯 聚甲基丙烯酸甲酯 (PS PMMA)复合粒子 .研究聚合物粒径分布和颗粒形态的变化发现 ,在St悬浮反应中期滴加MMA乳液聚合组分后 ,聚合体系逐渐由悬浮粒子与乳胶粒子并存向形成单峰分布复合粒子转变 ,最终形成核 壳结构完整的大粒径PS PMMA复合粒子 ;在St悬浮反应初期滴加MMA乳液聚合组分 ,St与MMA一起分散成更小液滴 ,反应后期凝并成非核 壳结构复合粒子 ;在St悬浮反应后期滴加MMA乳液聚合组分 ,PMMA乳胶粒子与PS悬浮粒子基本独立存在 .根据以上结果 ,提出了St MMA悬浮 乳液复合聚合的成粒机理 .  相似文献   

2.
以甲基丙烯酸三氟乙酯(TFMA)、苯乙烯(St)和丙烯酸丁酯(BA)为共聚单体,在十二烷基硫酸钠(SDS)/磺酸盐型阴离子氟表面活性剂(S100)/辛基苯基聚氧乙烯醚(OP-10)组成的乳化体系中,采用预聚物和十六醇(HDL)共同组成的复合助稳定剂,对细乳液聚合制备St/BA/TFMA三元共聚物的过程进行了研究.通过F...  相似文献   

3.
以苯乙烯(St)和丙烯酸(AA)为单体,过硫酸钾(KPS)为引发剂,采用无皂乳液聚合法合成了单分散阴离子聚苯乙烯(PS)微球,并对微球结构和影响单分散性的因素进行了研究。结果表明,AA单体也已共聚到聚合物链上,AA的加入使PS微球粒径减小,并赋予PS微球表面负电性;聚合反应的活化能为42.95kJ/mol,升高聚合温度提高了反应速率;随着KPS用量的增加,PS微球粒径减小,在用量为0.6%时呈现最好单分散性;随着反应介质中丙酮含量增加,聚合物在介质中溶解度增加,使PS微球粒径有所减小,但微球粒径分布有所变宽。  相似文献   

4.
溶剂热法制备小粒径无皂MMA/St共聚纳米胶乳粒子   总被引:3,自引:0,他引:3  
溶剂热法制备小粒径无皂MMA/St共聚纳米胶乳粒子;溶剂热法;无皂乳液聚合;纳米粒子;聚(苯乙烯甲基丙烯酸甲酯)  相似文献   

5.
高表面电荷密度单分散苯乙烯磺酸钠纳米微球的制备   总被引:5,自引:0,他引:5  
利用无皂乳液聚合 ,在苯乙烯 (St)的反应体系中引入适量的苯乙烯磺酸钠 (NaSS)参加共聚合 ,在聚合过程中分两阶段加料 ,第一阶段中NaSS浓度是决定乳胶粒粒径及单分散性的关键因素。当反应达到较高转化率 ( >90 % )时加入第二阶段单体混合物 ,此阶段中NaSS与St的比例决定了最终胶粒的表面电荷密度。利用上述两阶段无皂乳液聚合法成功地制备了粒径小于 10 0nm、单分散性指数小于 1.0 5以及表面电荷密度大于 3 0 μC·cm-2 的一系列乳胶粒  相似文献   

6.
用二氧化硅 (SiO2 )存在下的乳液聚合法制备了聚苯乙烯 (PSt) 纳米SiO2 复合材料 ,研究了苯乙烯(St)乳液聚合过程中团聚纳米SiO2 的解离与再分散过程及分散的机理 .发现商品纳米SiO2 粒子以团聚体形式存在 ,团聚体大小远超出纳米级范围 .随聚合时间的延长 ,St的转化率逐渐增加 ,而PSt SiO2 复合微胶囊的粒径逐渐减小 ,反应 12 0min后 ,转化率和复合微胶囊粒子的粒径趋于稳定 .透射电镜 (TEM)也显示PSt SiO2 复合微胶囊粒子具有海岛结构 ,而SiO2 粒子的粒径在纳米范围内 ,表明在乳液聚合过程中SiO2 团聚体被逐渐解离 ,并重新分散到纳米尺度 .红外光谱研究发现 ,在乳液聚合过程中 ,除生成PSt均聚物外 ,还在纳米SiO2 表面生成了PSt接枝共聚物 ,改善了无机纳米粒子与聚合物之间的界面相容性 .聚合过程中的反应热和剪切搅拌是团聚体被解离和重新分散的主要原因 ,而生成的聚合物起到隔离作用  相似文献   

7.
PU-St超浓乳液聚合动力学及聚合物性质的研究   总被引:3,自引:0,他引:3  
采用一步法制备聚氨酯预聚体 ( PU)苯乙烯 ( St)超浓乳液 ,探讨了稳定的超浓乳液的 NCO/OH和 St/PU最佳比例范围。研究了乳化剂和引发剂浓度对超浓乳液聚合的稳定性及聚合动力学的影响 ,并制得了用 PU改性的聚苯乙烯 ( PS)粉状树脂。测定了乳胶粒子大小、粒径分布、分子量和聚合物膜的动态力学性质。发现乳胶粒子大小及其单分散性随聚合转化率的增加而增加 ;与本体聚合比较 ,聚合物的分子量有明显增大 ;PU- PS复合聚合物具有优良性能。  相似文献   

8.
将超声技术引入到无皂乳液聚合方法中,在不加入任何引发剂和乳化剂的情况下,制备了丙烯酸丁酯(BA)/苯乙烯(St)/丙烯酰胺(AM)三元共聚纳米乳胶粒.研究了不同超声时间对单体转化率、乳胶粒粒径以及乳液粘度的影响.同时还探讨了超声无皂乳液聚合机理,认为AM在聚合过程中起到了引发和稳定的作用.TEM照片表明,乳胶粒直径大约在80nm左右,FTIR及DSC分析表明产物为三元共聚物,而不是共混物.  相似文献   

9.
首先用无皂乳液聚合法制备了单分散聚苯乙烯(PSt)乳液,以此为种子乳液,使用N,N-亚甲基双丙烯酰胺(MBA)为交联剂,过硫酸钾(KPS)为引发剂,进行苯乙烯和N-乙烯基吡咯烷酮(NVP)共聚合制备了以PSt为核、St和NVP共聚物为壳的具有核-壳结构的聚合物微球(P(St-NVP)).以此微球为模板通过化学沉积法得到了粒径分布均匀、单分散的P(St-NVP)/Ag复合微球.傅里叶红外光谱、X-射线衍射、扫描电镜、透射电镜、激光粒度仪和紫外-可见光谱对复合微球的结构、形貌、物相及催化性能进行了表征.结果表明,P(St-NVP)/Ag复合微球具有规则的球形结构,粒径在400~700 nm之间,随交联剂浓度或种子乳液浓度的增加,复合微球粒径减小.粒径在十几个纳米左右的银粒子均匀分布在微球表面和内部.载银复合微球在NaBH4还原4-硝基苯酚为4-氨基苯酚的模型反应中表现出较高的催化活性.  相似文献   

10.
通过乳液聚合法和无皂乳液聚合法制备了苯乙烯/丙烯酸正丁酯/丙烯酸共聚微球.讨论了乳化剂用量、引发剂用量、功能单体、软硬单体用量比等对微球粒径和形态的影响.利用扫描电子显微镜(SEM)、傅立叶变换红外光谱仪(FTIR)对微球的粒径、形貌和表面基团进行分析.红外光谱表明,实验室所制备的苯乙烯/丙烯酸正丁酯/丙烯酸共聚微球表面存在丰富的羧基.利用竖片生长法得到自组装的多层胶体微球薄膜.通过对薄膜的反射光谱测量,发现随着湿度的增加,峰位会产生3nm左右的红移.  相似文献   

11.
光散射法研究丙烯酸十八酯和苯乙烯微乳液 共聚机理   总被引:25,自引:0,他引:25  
在十六烷基溴化吡啶/叔丁醇/15%丙烯酸十八酯和苯乙烯/水体系的O/W微乳液中,使用动态光散射法,研究其中两种单体共聚反应的成核机理。结果表明,聚合过程中乳胶粒成核位置主要在增溶胶囊的单体微珠中,乳胶粒主要依靠单体微珠不断提供单体而长大。  相似文献   

12.
The mechanism of surfactant-free emulsion polymerization of styrene   总被引:1,自引:0,他引:1  
New experimental data on the mechanism of particle formation in the surfactant-free emulsion polymerization of styrene under static conditions are described. It is shown that the concentration of styrene in the aqueous phase affects the mechanism of particle nucleation and changes in the dispersity of systems during polymerization and nucleation of particles with different properties.  相似文献   

13.
The emulsifier-free emulsion polymerizations of styrene in the presence of about 0.33–2.7% (relative to styrene) of the water soluble comonomer, 2-hydroxyethyl methacrylate (HEMA), and of the initiator, potassium persulfate (KPS), were carried out. It was found that KPS plays a predominant role in the particle nucleation process, since the number density of polymer particles (Np) was dependent on the 0.97-power of [KPS]. The nucleation ability of HEMA was weak, since Np was dependent only on the 0.17-power of [HEMA]. The particle nucleation stage ceased quite early before 1% conversion, leading to nearly monodispersed polymer particles. The nucleation is suggested to be via the homogeneous nucleation mechanism. The particles grow via the core-shell structure mechanism (shell region polymerization), since the particle size is rather large—from 1500 to 6000 Å. The amount of HEMA can affect the shell thickness and physical properties of the shell, such as the monomer swelling capacity and monomer diffusion rate.  相似文献   

14.
The kinetics of the emulsifier-free emulsion copolymerization of styrene and sodium styrene sulfonate have been examined over a range of comonomer compositions. The rate of polymerization was found to increase dramatically in the presence of small amounts of sodium styrene sulfonate. This increase is attributed to the increased number of particles formed when sodium styrene sulfonate was present and to a gel effect enhanced by ion association. At low concentrations of functional comonomer, where a monodisperse product was obtained, a homogeneous nucleation mechanism of particle generation is proposed. At higher concentrations, broader and then bimodal size distributions were obtained, and this is ascribed to significant aqueous phase polymerization of sodium styrene sulfonate. The water-soluble homopolymer is supposed to act as a locus of polymerization. The occurrence of this aqueous phase side reaction and the generation of secondary particles makes impossible the preparation of highly sulfonated polystyrene latexes by batch or seeded batch emulsion copolymerization.  相似文献   

15.
The effects of concentrations of surfactant (sodium lauryl sulfate [SLS]) and initiator (sodium persulfate [SPS]) on the polymerization of homogenized styrene emulsions, stabilized by SLS/lauryl methacrylate (LMA) or SLS/stearyl methacrylate (SMA), were studied. The rate of polymerization increases with increasing [SLS] or [SPS]. In addition to monomer droplet nucleation, the formation of particle nuclei in the aqueous phase (homogeneous nucleation) plays a crucial role in the polymerization kinetics. In comparison with the LMA containing polymerization system, monomer droplet nucleation becomes more important when the more hydrophobic SMA was used as the costabilizer. Furthermore, the degree of homogeneous nucleation increases with increasing [SPS].  相似文献   

16.
The application of atypical experimental methods such as conductivity measurements, optical microscopy, and nonstirred polymerizations to investigations of the ‘classical’ batch ab initio emulsion polymerization of styrene revealed astonishing facts. The most important result is the discovery of spontaneous emulsification leading to monomer droplets even in the quiescent styrene in water system. These monomer droplets with a size between a few and some hundreds of nanometers, which are formed by spontaneous emulsification as soon as styrene and water are brought into contact, have a strong influence on the particle nucleation, the particle morphology, and the swelling of the particles. Experimental results confirm that micelles of low-molecular-weight surfactants are not a major locus of particle nucleation. Brownian dynamics simulations show that the capture of matter by the particles strongly depends on the polymer volume fraction and the size of the captured species (primary free radicals, oligomers, single monomer molecules, or clusters).  相似文献   

17.
Particle formation in polymerization of styrene induced within two stratified layers of a monomer and water containing an initiator was studied in the absence of emulsifiers and stirring. A polymerization-induced decrease of interfacial surface tension was observed. The particle size distribution was characterized by dynamic light scattering during polymerization. The results confirm particle nucleation through spontaneous emulsification process.  相似文献   

18.
The nucleation mechanism of styrene emulsion polymerization in the presence of the nonionic surfactant Emulphogene BC-840 was investigated. It was found that the conversion-time curves of this system show two rate regions. The change in rate occurs at ca. 40% conversion. Second-stage nucleation leads to a faster rate and consequently to a bimodally dispersed latex. The particle size distribution is relatively narrow before 40% conversion. The bimodally dispersed latex shows a bimodal molecular weight distribution in gel permeation chromatography and the results from fractional “creaming” of the latex indicate that the small-size particles contain the higher-molecular-weight polymer.  相似文献   

19.
Emulsion copolymerizations of styrene were carried out with four structurally different ionic comonomers namely acrylic acid (AAc), methacrylic acid (MAA), 2-hydroxyethyl methacrylate (HEMA), and sodium styrene sulfonate (NaSS) to study the effect of monomer structure on the copolymerization kinetics and size, morphology, charge density, and the self-assembly of the particles. The copolymerization kinetics was found to be highly dependent upon the ionic comonomer structure, and the nature of this dependence altered from homogeneous to micellar nucleation regime. The decrease in particle size (D) with increasing surfactant concentration (S) was observed in all the cases; however, the exponents of D vs. S were not similar for all the cases. In the homogeneous nucleation regime, exponents followed the order as AAc (0.446) > MAA (0.396) > NaSS (0.252) > HEMA (0.241), whereas the order was almost reversed in the micellar nucleation regime as NaSS (0.406) > HEMA (0.228) > AAc (0.206) > MAA (0.172). The hydrophobic/hydrophilic character and the steric factors were found to be the driving force for the variation in D vs. S exponents with ionic comonomer structure. The presence of charges on the particle surface contributed by the ionic comonomers triggered the self-assembly of the particles upon sedimentation and diffracted visible light obeying Bragg's law.  相似文献   

20.
To clarify the mechanism of the nucleation process in the soap-free polymerization of styrene in water, the polymerization process of styrene mainly at a temperature 46 degrees C was investigated on a molecular scale using an atomic force microscope (AFM) as well as a scanning electron microscope (SEM) and a dynamic light scattering apparatus (DLS). A cationic initiator was employed to make polymerized styrene adsorb electrostatically on the negatively charged mica plate with molecular-scale smoothness, and the mechanism was estimated from their AFM measurements in situ in water. The following was found. There exist two streams to produce PSL particles in the polymerization: one is the polymerization in monomer droplets fragmented by mixing from the main monomer reservoir floating above the solution, and the other is the polymerization of monomers dissolved in the solution by initiators. The former is normally neglected or not recognized because of the small contribution. The latter is the main production process of PSL particle, which is investigated in detail on a molecular scale, and a possible mechanism was proposed.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号