Electrochemical Preparation of Poly(Malachite Green) Film Modified Nafion‐Coated Glassy Carbon Electrode and Its Electrocatalytic Behavior Towards NADH,Dopamine and Ascorbic Acid

Poly(malachite green) film modified Nafion‐coated glassy carbon electrodes have been prepared by potentiodynamic cycling in malachite green solution. The pH of polymerisation solution has only minor effect on film formation. Electrochemical quartz crystal microbalance (EQCM) was used to monitor the growth of the poly(malachite green) film. Cyclic voltammogram of the poly(malachite green) film shows a redox couple with well‐defined peaks. The redox response of the modified electrode was found to be depending on the pH of the contacting solution. The peak potentials were shifted to a less positive region with increasing pH and the dependence of the peak potential was found to be 56 mV per pH unit. The electrocatalytic behavior of poly(malachite green) film modified Nafion‐coated glassy carbon electrodes was tested towards oxidation of NADH, dopamine, and ascorbic acid. The oxidation of dopamine and ascorbic acid occurred at less positive potential on poly(malachite green) film compared to bare glassy carbon electrode. In the case of NADH, the overpotential was reduced substantially on modified electrode. Finally, the feasibility of utilizing poly(malachite green) film electrode in analytical estimation of ascorbic acid was demonstrated in flow injection analysis.     

NADH Oxidation Catalyzed by Electropolymerized Azines on Carbon Nanotube Modified Electrodes

Electropolymerizing azines on a carbon nanotube (CNT) modified electrode yields a high‐surface area interface with excellent electrocatalytic activity towards NADH oxidation. Electrodeposition of poly(methylene green) (PMG) and poly(toluidine blue) (PTBO) on the carboxylated CNT‐modified electrodes was achieved by cyclic voltammetry. The PMG‐CNT interface demonstrates 5.0 mA cm^?2 current density for NADH oxidation at 50 mV vs. Ag|AgCl in 20 mM NADH solution. The kinetics of NADH electrocatalysis were analyzed using a quantitative mass‐transport‐corrected model with NADH bulk concentration and applied potential as independent variables. This high‐rate poly(azine)‐CNT interface is potentially applicable to high‐performance bioconversion, bioenergy and biosensors involving NADH‐dependent dehydrogenases.     

Exploring the electrocatalytic sites of carbon nanotubes for NADH detection: an edge plane pyrolytic graphite electrode study

The electrocatalytic properties of multi-walled carbon nanotube modified electrodes toward the oxidation of NADH are critically evaluated. Carbon nanotube modified electrodes are examined and compared with boron-doped diamond and glassy carbon electrodes, and most importantly, edge plane and basal pyrolytic graphite electrodes. It is found that CNT modified electrodes are no more reactive than edge plane pyrolytic graphite electrodes with the comparison with edge plane and basal plane pyrolytic graphite electrodes allowing the electroactive sites for the electrochemical oxidation of NADH to be unambiguously determined as due to edge plane sites. Using these highly reactive edge plane sites, edge plane pyrolytic graphite electrodes are examined with cyclic voltammetry and amperometry for the electroanalytical determination of NADH. It is demonstrated that a detection limit of 5 microM is possible with cyclic voltammetry or 0.3 microM using amperometry suggesting that edge plane pyrolytic graphite electrodes can conveniently replace carbon nanotube modified glassy carbon electrodes for biosensing applications with the relative advantages of reactivity, cost and simplicity of preparation. We advocate the routine use of edge plane and basal plane pyrolytic graphite electrodes in studies utilising carbon nanotubes particularly if 'electrocatalytic' properties are claimed for the latter.     

Enhanced NADH Oxidation Using Polytyramine/Carbon Nanotube Modified Electrodes for Ethanol Biosensing

Polytyramine (PT) has been electro‐deposited onto multi‐walled carbon nanotube (MWCNT) modified glassy carbon (GC) electrodes via oxidation of tyramine in 0.1 M H₃PO₄ by cycling the potential over the range of −400 mV to 1300 mV (versus Ag/AgCl). The reactivity of the resulting chemically‐modified electrodes was characterized using cyclic voltammetry in the presence and absence of reduced nicotinamide adenine dinucleotide (NADH). The modified electrodes displayed electrochemical activity due to the formation of quinone species and were catalytically active towards NADH oxidation by lowering the oxidation peak potential by 170 mV compared to the value of the MWCNT modified electrode with a peak potential of 180±10 mV (versus Ag/AgCl). The MWCNT/PT surface was further characterized using SEM and XPS methods, which indicated that a thin polymeric film had been formed on the electrode surface. The present work demonstrates the advantage of using PT as a platform that combines both the immobilization of alcohol dehydrogenase (ADH) and the mediation of NADH oxidation at a low overpotential essential to the design of high performance ethanol biosensors, all within an easily electropolymerizable film. The resulting biosensor displayed an ethanol sensitivity of 4.28±0.06 μA mM⁻¹ cm⁻², a linear range between 0.1 mM and 0.5 mM and a detection limit of 10 μM.     

Carbon nanofiber vs. carbon microparticles as modifiers of glassy carbon and gold electrodes applied in electrochemical sensing of NADH

Carbon materials (CMs), such as carbon nanotubes (CNTs), carbon nanofibers (CNFs), and carbon microparticles (CMPs) are used as doping materials for electrochemical sensors. The efficiency of these materials (either before or after acidic treatments) while being used as electrocatalysts in electrochemical sensors is discussed for β-nicotinamide adenine dinucleotide (NADH) detection using cyclic voltammetry (CV). The sensitivity of the electrodes (glassy carbon (GC) and gold (Au)) modified with both treated and untreated materials have been deeply studied. The response efficiencies of the GC and Au electrodes modified with CNF and CMP, using dimethylformamide (DMF) as dispersing agent are significantly different due to the peculiar physical and chemical characteristics of each doping material. Several differences between the electrocatalytic activities of CMs modified electrodes upon NADH oxidation have been observed. The CNF film promotes better the electron transfer of NADH minimizing the oxidation potential at +0.352 V. Moreover higher currents for the NADH oxidation peak have been observed for these electrodes. The shown differences in the electrochemical reactivities of CNF and CMP modified electrodes should be with interest for future applications in biosensors.     

聚灿烂甲酚蓝修饰玻碳电极的制备及电化学性质

在含灿烂甲酚蓝的磷酸缓冲溶液中,用循环伏安法扫描.在经预处理的玻碳电极上形成了聚合物薄膜.在-0.7V-+0.9V(vsSCE)的扫描电位范围和弱碱性介质中形成的薄膜具有较高电活性和稳定性.制备好的聚灿烂甲酚蓝修饰电极在磷酸缓冲溶液的循环伏安曲线有两对氧化还原峰,峰电位随pH升高而向负电位方向移动.该电极对NADH的电化学氧化有催化作用,使其氧化电位负移了270mV并增大了氧化峰电流.     

Exploring Multiwalled Carbon Nanotubes for Naproxen Detection

The electrochemical oxidation of naproxen was investigated at a multiwalled carbon nanotube (MWCNT)‐modified electrode. A decrease (200 mV) in the overpotential of the naproxen oxidation reaction and considerable (4‐fold) current increase (compared to the bare glassy‐carbon electrode) was observed. Two one‐electron transfers were verified at both bare and MWCNT‐modified electrodes and thus a new mechanism for the electrochemical oxidation of naproxen is proposed. Indicative of a mass transport regime that includes a thin‐layer diffusional process (entrapment of naproxen species within the MWCNT film) is presented as a possible explanation for the lowered oxidation potential and substantial current increase. The anti‐fouling properties of MWCNTs on the amperometric detection of naproxen using a batch‐injection analysis (BIA) system is demonstrated.     

Electrochemical Preparation of Brilliant‐Blue‐Modified Poly(diallyldimethylammonium Chloride) and Nafion‐Coated Glassy Carbon Electrodes and Their Electrocatalytic Behavior Towards Oxygen and L‐Cysteine

Brilliant blue FCF‐modified glassy carbon electrodes have been prepared by cycling the Nafion (or poly(diallyldimethylammonium chloride) (PDDAC)) coated electrodes repeatedly 15 cycles in brilliant blue FCF (BB FCF) dye solution. The BB FCF molecules are incorporated into Nafion coating by cycling the film‐covered electrode between +0.3 to 1.2 V (vs. Ag/AgCl) in pH 1.5 BB FCF solution while PDDAC‐coated electrode cycled between 0 to ?1.0 V (vs. Ag/AgCl) in pH 6.5 BB FCF solution to immobilize the dye. Electrostatic interaction between dye molecule and PDDAC was predominant in PDDAC coating whereas immobilization of dye in Nafion film attributed to the combined effect of electrostatic and hydrophobic interactions. The voltammetric features of BB FCF‐modified electrodes resemble that of surface‐confined redox couples. The peak potentials of BB FCF‐incorporated PDDAC‐coated electrode were shifted to more positive potential region with decreasing pH of contacting solution. BB FCF‐modified electrodes showed electrocatalytic activity towards reduction of oxygen and oxidation of L ‐cysteine with significant decease of overvoltage compared to unmodified electrode. The BB FCF‐modified Nafion‐coated electrode was tested for its analytical applications toward determination of L ‐cysteine. The linear range of calibration plot at BB FCF‐modified Nafion‐coated electrode is 10 to 100 μM, which coincides with L ‐cysteine levels in biological fluids. Sensitivity and detection limit of the electrode are 111 nA μM^?1 and 0.5 μM, respectively.     

Amperometric Sensor for Detection of the Reduced Form of Nicotinamide Adenine Dinucleotide Using a Poly(pyronin B) Film Modified Electrode

An electrochemical method for the preparation of poly(pyronin B) film was proposed in this paper. A poly(pyronin B) (poly(PyB)) film modified glassy carbon electrode (GCE) has been fabricated via an electrochemical oxidation procedure and applied to the electrocatalytic oxidation of reduced form of nicotinamide adenine dinucleotide (NADH). The poly(PyB) film modified electrode surface has been characterized by atomic force microscope (AFM), scanning electron microscope (SEM), electrochemical impedance spectroscopy (EIS), UV‐visible absorption spectrophotometry (UV‐vis) and cyclic voltammetry (CV). These studies have been used to investigate the poly(PyB) film, which demonstrates the formation of the polymer film and the excellent electroactivity of poly(PyB) in neutral and even in alkaline media. Due to its potent catalytic effects towards the electrooxidation of NADH at lower potential (0.0 V), poly(PyB) film modified electrode can be used for the selective determination of NADH in real samples because of dopamine, ascorbic acid and uric acid oxidation can be avoided at this potential. The catalytic peak currents are linearly dependent on the concentrations of NADH in the range of 1.0×10^?6 to 5.0×10^?4 mol/L with correlation coefficients of 0.999. The detection limits for NADH is 0.5×10^?6 mol/L. Poly(PyB) modified electrode also shows good stability and reproducibility due to the irreversible attachment of polymer film at GCE surface.     

A Mediator‐Free Bienzyme Amperometric Biosensor Based on Horseradish Peroxidase and Glucose Oxidase Immobilized on Carbon Nanotube Modified Electrode

Multiwalled carbon nanotube (CNT) modified glassy carbon electrode immobilized with horseradish peroxidase (HRP) in Nafion coating showed direct electron transfer between HRP enzyme and the CNT‐modified electrode. A mediator‐free bienzyme glucose biosensor based on horseradish peroxidase and glucose oxidase was constructed. The bienzyme biosensor exhibited a high sensitivity for glucose detection at zero applied potential.     

Glucose Biosensor Based on Multi‐Walled Carbon Nanotube Modified Glassy Carbon Electrode

An amperometric glucose biosensor based on multi‐walled carbon nanotube (MWCNT) modified glassy carbon electrode has been developed. MWCNT‐modified glassy carbon electrode was obtained by casting the electrode surface with multi‐walled carbon nanotube materials. Glucose oxidase was co‐immobilized on the MWCNT‐modified glassy carbon surface by electrochemical deposition of poly(o‐phenylenediamine) film. Enhanced catalytic electroreduction behavior of oxygen at MWCNT‐modified electrode surface was observed at a potential of ?0.40 V (vs. Ag|AgCl) in neutral medium. The steady‐state amperometric response to glucose was determined at a selected potential of ?0.30 V by means of the reduction of dissolved oxygen consumed by the enzymatic reaction. Common interferents such as ascorbic acid, 4‐acetamidophenol, and uric acid did not interfere in the glucose determination. The linear range for glucose determination extended to 2.0 mM and the detection limit was estimated to be about 0.03 mM.     

Electro-oxidative polymerization of phenothiazine dyes into a multilayer-containing carbon nanotube on a glassy carbon electrode for the sensitive and low-potential detection of NADH

An electrochemical sensing platform was developed for the amperometric detection of β-nicotinamide adenine dinucleotide (NADH) through the integration of a multi-walled carbon nanotube (MWCNT) into electropolymerized phenothiazine dyes. The composite containing MWCNT and poly(phenothiazine) was prepared by electro-oxidative polymerization of phenothiazine derivatives, Azure B, Azure A and thionine, into an MWCNT/ poly(diallyldimethylammonium chloride) (PDDA) multilayer, which was constructed by electrostatic layer-by-layer assembly on a glassy carbon electrode. The three phenothiazine monomers used in this study exhibited similar electrochemical behaviors. Azure B was used extensively as a model monomer for the investigation. Electrochemical techniques and scanning electron microscopy were used to demonstrate that the porous composite was formed and that the carbon nanotube served as a nano-sized backbone for the loading of polymeric phenothiazine. The electrocatalytic current for NADH oxidation was enhanced as the number of layers increased, implying that the increase of NADH-accessible poly(phenothiazine) and the three-dimensional arrangement of the poly(phenothiazine)-coated MWCNT in the composite facilitated electron and NADH transfer. Under optimal conditions, the detection limit for NADH decreases to 7.0 × 10^?8?M at a potential of 0.1 V (versus Ag/AgCl) using a {MWCNT/PDDA}₈?poly(Azure B) composite modified glassy carbon electrode, with a response time of about 5 s. This work demonstrates that the electropolymerization of the phenothiazine monomer into a pre-formed multilayer containing MWCNT can be used for the controllable preparation of stable MWCNT/poly(phenothiazine) composites on electrode surfaces, which have the potential to provide a platform for electrochemical biosensors based on NAD⁺-dependent dehydrogenase enzymes.     

Selective Determination of Quercetin Using Carbon Nanotube‐Modified Electrodes

Electrochemical detection of quercetin has been carried out on glassy carbon electrodes modified with carbon nanotubes and Nafion (GC/Nafion‐CNT). GC/Nafion‐CNT electrodes did not show passivation effect that occurs on the unmodified electrodes and displayed better stability and reproducibility. Quercetin oxidation was most favorable in acidic conditions and current gradually decreased as the solution pH increased. No oxidation was observed when two ? OH groups in a catechol moiety were fully deprotonated. These electrodes enabled selective determination of quercetin in the presence of interfering species such as ascorbic acid, uric acid, glucose, and catechol in large excess. Quantification of quercetin in a yellow onion has been made and favorably compared with reported values. Good selectivity and high sensitivity obtained by Osteryoung sSquare‐wave voltammetry can open new possibilities of direct quercetin determination in vegetables with a minimal sample treatment.     

Demonstration of the advantages of using bamboo-like nanotubes for electrochemical biosensor applications compared with single walled carbon nanotubes

The modification of glassy carbon electrodes with random dispersions of nanotubes is currently the most popular approach to the preparation of carbon nanotube modified electrodes. The performance of glassy carbon electrodes modified with a random dispersion of bamboo type carbon nanotubes was compared with single walled carbon nanotubes modified glassy carbon electrodes and bare glassy carbon electrodes. The electrochemical performance of all three types for electrode were compared by investigating the electrochemistry with solution species and the oxidation of guanine and adenine bases of surface adsorbed DNA. The presence of edge planes of graphene at regular intervals along the walls of the bamboo nanotubes resulted in superior electrochemical performance relative to SWNT modified electrodes from two aspects. Firstly, with solution species the peak separation of the oxidation and reduction waves were smaller indicating more rapid rates of electron transfer. Secondly, a greater number of electroactive sites along the walls of the bamboo-carbon nanotubes (BCNTs) resulted in larger current signals and a broader dynamic range for the oxidation of DNA bases.     

Comparative Studies on Electrocatalytic Activities of Chemically Reduced Graphene Oxide and Electrochemically Reduced Graphene Oxide Noncovalently Functionalized with Poly(methylene blue)

This study compares the electrocatalytic activities of chemically reduced graphene oxide (crGO) and electrochemically reduced graphene oxide (erGO), which are both noncovalently functionalized with a polyaromatic dye, poly(methylene blue) (polyMB), toward the oxidation of β‐nicotinamide adenine dinucleotide (NADH). PolyMB‐crGO and polyMB‐erGO composites were obtained via electropolymerization of methylene blue on crGO and GO modified glassy carbon (GC) electrodes, respectively. Cyclic voltammetry (CV) results indicate that these two types of integrated electrodes reveal different electrocatalytic activities. PolyMB‐crGO integrated electrode possesses lower catalytic oxidation potential, suggesting higher catalytic activity. The present study is helpful for the understanding and screening of graphene‐based advanced carbon nanomaterials for potential electrochemical applications.     

Low potential detection of nicotine at multiwalled carbon nanotube–alumina-coated silica nanocomposite

Electrocatalytic oxidation of nicotine at multiwalled carbon nanotube (MWCNT)–alumina-coated silica (ACS) nanocomposite modified glassy carbon electrode are described. The sensing performance of the MWCNT–ACS nanocomposite modified glassy carbon electrode for the electrooxidation of nicotine was investigated using cyclic voltammetry and amperometry in 0.1 M phosphate buffer solution (pH 8). The MWCNT–ACS nanocomposite modified glassy carbon electrode exhibited the abilities to decrease the electrooxidation potential, to prevent the electrode surface fouling, and to raise the current responses. The MWCNT–ACS nanocomposite responded rapidly to nicotine with a sensitivity of 1.786 A M^?1 cm^?2 and a detection limit of 1.42 μM (according to 3σ criterion). A signal almost 180 times more sensitive was obtained at MWCNT–ACS nanocomposite modified glassy carbon electrodes as compared to bare glassy carbon electrode. The nicotine oxidation potential obtained in this study is much lower than that at boron-doped diamond electrodes.     

The NADH Electrochemical Detection Performed at Carbon Nanofibers Modified Glassy Carbon Electrode

In this work, the capability of carbon nanofibers to be used for the design of catalytic electrochemical biosensors is demonstrated. The direct electrochemistry of NADH was studied at a glassy carbon electrode modified using carbon nanofibers. A decrease of the oxidation potential of NADH by more than 300 mV is observed in the case of the assembled carbon nanofiber‐glassy carbon electrode comparing with a bare glassy carbon electrode. The carbon nanofiber‐modified electrode exhibited a wide linear response range of 3×10^?5 to 2.1×10^?3 mol L^?1 with a correlation coefficient of 0.997 for the detection of NADH, a high specific sensitivity of 3637.65 (μA/M cm²), a low detection of limit (LOD=3σ) of 11 μM, and a fast response time (3 s). These results have confirmed the fact that the carbon nanofibers represent a promising material to assemble electrochemical sensors and biosensors.     

Direct Electrochemistry of Glucose Oxidase at Carbon Nanotube‐gold Colloid Modified Electrode with Poly(diallyldimethylammonium chloride) Coating

Glucose oxidase showed direct electrochemical transfer at glassy carbon electrodes immobilized with carbon nanotube‐gold colloid (CNT‐Au) composites with poly(diallydimethylammonium chloride) (PDDA) coatings. The modified electrode (GC/CNT/Au/PDDA‐GOD) was employed for the amperometric determination of glucose. Under optimal conditions, the biosensor displayed linear response to glucose from 0.5 to 5 mM with a sensitivity of 2.50 mA M^?1 at an applied potential of ?0.3 V (vs. Ag|AgCl reference).     

Influence of Metal Nanoparticles on the Electrocatalytic Oxidation of Glucose by Poly(NiIIteta) Modified Electrodes

Conductive polymeric [Ni^II(teta)]²⁺ (teta=C‐meso‐5,5,7,12,12,14‐hexamethyl‐1,4,8,11‐tetra‐azacyclotetradecane) films (poly(Ni)) have been deposited on the surface of glassy carbon (GC), Nafion (Nf) modified GC (GC/Nf) and Nf stabilized Ag and Au nanoparticles (NPs) modified GC (GC/Ag‐Nf and GC/Au‐Nf) electrodes. The cyclic voltammogram of the resulting electrodes, show a well defined redox peak due to oxidation and reduction of poly(Ni) system in 0.1 M NaOH. They show electrocatalytic activity towards the oxidation of glucose. AFM studies reveal the formation of poly(Ni) film on the modified electrodes. Presence of metal NPs increases electron transfer rate and electrocatalytic oxidation current by improving the communication within the Nf and poly(Ni) films. In the presence of metal NPs, 4 fold increase in current for glucose oxidation was observed.     

Enhanced Hydrogen Peroxide Sensing Based on Tetraruthenated Porphyrins/Nafion/Glassy Carbon‐modified Electrodes via Incorporating of Carbon Nanotubes

The incorporation of carbon nanotubes to a Nafion/tetraruthenated cobalt porphyrin/ glassy carbon electrode (GC/Nf/CoTRP vs GC/Nf/CNTCoTRP) enhanced the amperometric determination of hydrogen peroxide. Both electrodes produced a decrease in the overpotential required for the hydrogen peroxide oxidation in about 100 mV compared to glassy carbon under the same experimental conditions. Nevertheless, for GC/Nf/CNT/CoTRP, the increase in the current is remarkable. The GC/Nf/CoTRP modified electrode gave no significant analitycal signal for hydrogen peroxide reduction. Moreover, a great increase in current is observed with GC/Nf/CNT/CoTRP at ?150mV which suggests a significant increase in the sensitivity of the modified electrode. Scanning electrochemical microscopy (SECM) revealed an enhancement in the electroactivity of the GC/Nf/CNT/CoTRP modified electrode. This fact has been explained in terms of enhanced homogeneity of the electrodic surface as a consecuence of better dispersibility of CNT‐CoTRP produced by a Nafion polyelectrolyte.