镧、铒共掺杂压敏漆的制备及荧光特性

以联吡啶,氯化钌,氯化镧,氯化铒为原料合成了镧、铒共掺杂的探针分子.将探针分子加入到硅溶胶基质中获得了镧、铒共掺杂的压敏漆样品.采用IR,SEM,XPS及荧光发射光谱对探针分子和压敏漆进行了测试分析.红外光谱测试结果表明,探针分子中联吡啶的结构没有被破坏.扫描电镜观察发现探针分子呈花瓣状,XPS测试发现压敏漆中含有Er,La,Ru等元素,说明稀土元素确实被掺入到压敏漆中.紫外吸收光谱表明压敏漆的最佳吸收波段位于200 ～ 500 nm处,选择410 nm作为激发光源,压敏漆在590 nm处有很强的荧光发射,并且随着空气压力的增大即氧分子浓度的增加,压敏漆的荧光强度降低,说明压敏漆具有较好的氧猝灭特性.     

Eu0.5La0.5（TTA）3/PMMA温敏漆的制备及性能研究

以氯化铕、氯化镧、噻吩甲酰基三氟丙酮(TTA)为原料合成了Eu0.5La0.5(TTA)3探针分子,将探针分子与甲基丙烯酸甲酯(MMA)混合后聚合,获得Eu0.5La0.5(TTA)3/PMMA温敏漆。采用红外光谱、扫描电镜、紫外吸收光谱及荧光光谱对探针分子及温敏漆性能进行了表征。红外光谱表明,Eu(La)与TTA形成配位键,且镧的掺入并未改变Eu(TTA)3结构;SEM照片显示探针分子为片状晶体;紫外吸收光谱表明,探针分子的最佳吸收波段位于226～381 nm处。340 nm激发下,发现温敏漆在613 nm处具有最强荧光发射峰,且镧的掺杂对Eu(TTA)3发光存在增益作用;不同温度下荧光光谱表明,随着温度的升高,温敏漆荧光发射强度逐渐减弱,说明温敏漆具有良好的温度猝灭特性。     

不同稀土掺杂温敏漆的制备及性能研究

以RuCl3,联吡啶为原料,并在其中分别加入氯化铒、氯化钕和氯化钆,制备了铒掺杂、钕掺杂及钆掺杂联吡啶钌探针分子,将三种探针分子分别加入到MMA中,在引发剂引发下进行聚合,获得三种稀土掺杂的温敏漆样品.对探针分子及温敏漆进行了红外光谱、紫外吸收和荧光光谱测试.红外光谱测试结果表明,探针分子中联吡啶钌的结构没有被破坏.紫外吸收光谱表明温敏漆的最佳吸收波段位于200～550 nm范围内.选择410 nm作为激发光源,发现三种温敏漆在610 nm左右有很强的荧光发射峰,并且随着温度的升高,三种温敏漆的荧光强度均减弱,说明具有良好的温度猝灭特性,其中钆掺杂温敏漆灵敏度最强.     

稀土钇掺杂Eu(TTA)3/PMMA温敏漆的制备及性能分析

本文以氯化铕、氯化钇、噻吩甲酰基三氟丙酮(TTA)为原料合成了钇掺杂Eu(TTA)3探针分子。将探针分子掺杂到聚甲基丙烯酸甲酯(PMMA)基质中,获得稀土钇掺杂Eu(TTA)3/PMMA温敏漆。采用IR、紫外吸收光谱和激发发射光谱对探针分子结构及温敏漆荧光特性进行了表征。红外光谱表明,稀土Eu(Y)与TTA形成配位键,且钇的掺入未改变Eu(TTA)3结构。紫外吸收光谱表明,探针分子的最佳吸收波段位于290~376 nm处。激发发射光谱表明,在340 nm激发下,温敏漆在614 nm处有最强发射峰,且钇对Eu(TTA)3发光具有增益作用,当钇含量为50%时,增益作用最强。不同温度下发射光谱表明,随着温度的升高,温敏漆的荧光发射强度逐渐减弱,说明温敏漆具有良好的温度猝灭特性,且掺入钇后温敏漆的测温灵敏度有所提高。     

以Eu(DBM)3Bipy为荧光探针的温敏漆的制备及性能表征

利用氯化铕(EuCl_3)、二苯甲酰甲烷(DBM)和联吡啶(Bipy)为原料合成了Eu(DBM)_3Bipy探针分子,并将探针分子掺入到甲基丙烯酸甲酯(MMA)中,在过氧化苯甲酰(BPO)引发剂的作用下聚合,获得温敏漆Eu(DBM)_3Bipy/PMMA。采用红外光谱仪、紫外吸收光谱仪、扫描电子显微镜和荧光光谱仪对探针分子的结构、形貌、发光性能和温敏漆的温度猝灭性能进行了表征。红外及紫外吸收光谱分析发现稀土离子Eu3+与配体配位成键,成功合成Eu(DBM)_3Bipy探针分子;扫描电镜及能谱分析表明Eu(DBM)_3Bipy探针分子呈碎片状,大小约为150 nm,且主要由C、N、O和Eu四种元素组成;荧光光谱表明,在367 nm激发下,Eu(DBM)_3Bipy探针分子的最佳发射波长位于612 nm,且第二配体Bipy对Eu(DBM)_3的荧光发射具有增益作用。在不同温度下测试温敏漆的荧光发射特性,发现温敏漆Eu(DBM)_3Bipy/PMMA在40~90℃温度区间内具有良好的荧光温度猝灭特性,测温灵敏度最高的温度区间位于40~60℃。     

以Eu(DBM)3Bipy为荧光探针的温敏漆的制备及性能表征

利用氯化铕（EuCl₃）、二苯甲酰甲烷（DBM）和联吡啶（Bipy）为原料合成了Eu（DBM）₃Bipy探针分子,并将探针分子掺入到甲基丙烯酸甲酯（MMA）中,在过氧化苯甲酰（BPO）引发剂的作用下聚合,获得温敏漆Eu（DBM）₃Bipy/PMMA。采用红外光谱仪、紫外吸收光谱仪、扫描电子显微镜和荧光光谱仪对探针分子的结构、形貌、发光性能和温敏漆的温度猝灭性能进行了表征。红外及紫外吸收光谱分析发现稀土离子Eu³⁺与配体配位成键,成功合成Eu（DBM）₃Bipy探针分子;扫描电镜及能谱分析表明Eu（DBM）₃ Bipy探针分子呈碎片状,大小约为150 nm,且主要由C、N、O和Eu四种元素组成;荧光光谱表明,在367 nm激发下,Eu（DBM）₃ Bipy探针分子的最佳发射波长位于612 nm,且第二配体Bipy对Eu（DBM）₃的荧光发射具有增益作用。在不同温度下测试温敏漆的荧光发射特性,发现温敏漆Eu（DBM）₃Bipy/PMMA在40~90℃温度区间内具有良好的荧光温度猝灭特性,测温灵敏度最高的温度区间位于40~60℃。     

以[Eu(PBrBA)3phen]和[Eu(PCBA)3phen]为探针的温敏漆制备及其性能对比

以氧化铕(Eu_2O_3)、对氯苯甲酸(PCBA)、对溴苯甲酸(PBrBA)和菲咯啉(phen)为原料制备了菲咯啉对氯苯甲酸铕[Eu(PCBA)_3phen]、菲咯啉对溴苯甲酸铕[Eu(PBrBA)_3phen]两种探针分子,并将这2种探针分子掺杂在甲基丙烯酸甲酯(MMA)中,以过氧化苯甲酰(BPO)为引发剂,制得Eu(PCBA)_3phen/PMMA和Eu(PBrBA)_3phen/PMMA温敏漆样品。利用红外光谱仪、扫描电子显微镜、紫外-可见分度光度计和荧光光谱仪对探针分子的组成结构、发光性能、形貌和温敏漆的温度敏感性进行了测试分析,研究了不同配体对探针分子发光性能和温敏漆性能的影响。结果表明,Eu~(3+)分别与对氯苯甲酸(PCBA)和对溴苯甲酸(PBrBA) 2种主配体配位,并且第二配体菲咯啉(phen)均参与了配位,成功合成了2种配合物。2种配合物均发出Eu~(3+)的特征荧光,其中以PBrBA为主配体的菲咯啉铕三元配合物具有更好的发光性能。此外,基于这2种探针分子制备的温敏漆在50～90℃范围内均具有温度猝灭性能,以Eu(PCBA)_3phen为探针制成的温敏漆温度敏感性更强。     

([Ru(bpy)_3]~(2+)-Eu(TTA)_3Phen)/PMMA温敏漆的制备及性能研究

合成了[Ru(bpy)3]2+和Eu(TTA)3Phen两种探针分子,并将两者与甲基丙烯酸甲酯(MMA)混合,在引发剂BPO作用下进行聚合,获得具有温度响应性能的([Ru(bpy)3]2+-Eu(TTA)3Phen)/PMMA温敏漆。采用IR、紫外吸收光谱和荧光光谱对探针分子的结构及温敏漆的荧光特性进行了表征。红外光谱和紫外吸收光谱表明:Ru与2,2'-联吡啶分子通过双氮配位,有O→Eu配位键形成。荧光光谱表明:温敏漆样品的温度猝灭性能较好,并且在不同温度范围内测温灵敏度不同,由452 nm激发时,温敏漆样品在25~45℃范围内测温灵敏度高,最强的荧光发射峰位于584 nm;由342 nm激发时,在45~65℃范围内测温灵敏度高,最强的荧光发射峰位于612 nm。     

脂肪酸铕配合物掺杂聚乙烯、聚丙烯和聚苯乙烯光致发光复合材料

合成了正己酸铕、正辛酸铕、月桂酸铕和硬脂酸铕4种不同碳链链长的脂肪酸铕配合物,通过哈克转矩流变仪将铕配合物(质量分数1%)机械掺杂于3种不同透明度的聚乙烯(PE)、聚丙烯(PP)和聚苯乙烯(PS)通用树脂中,制备了系列铕配合物掺杂聚合物光致发光复合材料,考察了配体、配合物、聚合物基体对复合材料的外观、透明性及其荧光性能的影响。 结果表明,4种脂肪酸铕配合物及其掺杂的复合材料在紫外光的激发下均在593、617 nm处发射强的Eu3+离子5D0→7F1、5D0→7F2跃迁的特征荧光;脂肪酸配体的碳链长短对铕配合物及复合材料的发光影响较小;PE、PP复合材料发光颜色与红光铕配合物相同,PS复合材料因基体PS和Eu3+离子的发光共同作用而呈现了玫瑰红的荧光发射。     

不同探针分子温敏漆的制备及性能对比研究

利用氯化铕(Eu Cl3)、苯甲酸(BA)、菲咯啉(Phen)和2,2′-联吡啶(Bipy)为原料合成了Eu(BA)_3Phen和Eu(BA)_3Bipy两种配合物,并将两种配合物分别掺入甲基丙烯酸甲酯(MMA)中,在过氧化苯甲酰(BPO)作用下引发聚合,获得不同探针分子的两种温敏漆Eu(BA)_3Phen/PMMA和Eu(BA)_3Bipy/PMMA。利用红外光谱、紫外吸收光谱和荧光光谱对两种探针分子及温敏漆的特性进行了表征,分析结果表明,探针分子Eu(BA)_3Phen的荧光强度明显强于Eu(BA)_3Bipy,相对应的两种温敏漆Eu(BA)_3Phen/PMMA与Eu(BA)_3Bipy/PMMA均有较好的温度猝灭特性,但是对比分析发现在25~35℃和35~45℃温度区间内温敏漆Eu(BA)_3Phen/PMMA的灵敏度较高,而在45~55℃和55~65℃温度区间内温敏漆Eu(BA)_3Bipy/PMMA的灵敏度较高,可见温敏漆在不同温度区间的测温灵敏度是不同的。     

铋酸盐铒玻璃在1.54 μm处的荧光特性研究

The bismuth glasses with Er3+ and Er3+/Yb3+ co doped were fabricated by the technique of high temperature melting. The absorption and fluorescence spectra, fluorescence lifetime and FWHM were measured. The explanation of concentration quenching in case of high level Er3＋ doped the bismuth glasses is given. The sensitizing of Yb3＋ to Er3＋ in Er3＋/Yb3＋ co doped bismuth glasses is discussed. The explanation of the influence on absorption and fluorescence spectra, fluorescence lifetime and FWHM in case of the change of Er3+ or Yb3+ in bismuth glasses with Er3+/Yb3+ co doped is given. It is found that the change of Er3+ content has obviously influenced the fluorescence lifetime and FWHM while the change of Yb3+ content has remarkably influenced the absorption and fluorescence intensity. The band at around 1.54 μm in Er3+/Yb3+ co doped bismuth glass reaches 76 nm and the fluorescence lifetime is 0.55 ms.     

Synthesis, characterization and photoluminescence properties of CaSiO3:Eu3+ red phosphor

CaSiO3:Eu3+ (1-5 mol%) red emitting phosphors have been synthesized by a low-temperature solution combustion method. The phosphors have been well characterized by powder X-ray diffraction (PXRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and optical spectroscopy. PXRD patterns reveal monoclinic CaSiO3 phase can be obtained at 900°C. The SEM micrographs show the crystallites with irregular shape, mostly angular. Upon 254 nm excitation, the phosphor show characteristic fluorescence 5D0→7FJ (J=0, 1, 2, 3, 4) of the Eu3+ ions. The electronic transition located at 614 nm corresponding to 5D0→7F2 of Eu3+ ions, which is stronger than the magnetic dipole transition located at 593 nm corresponding to 5D0→7F1 of Eu3+ ions. Different pathways involved in emission process have been studied. Concentration quenching has been observed for Eu3+ concentration>4 mol%. UV-visible absorption shows an intense band at 240 nm in undoped and 270 nm in Eu3+ doped CaSiO3 which is attributed to oxygen to silicon (O-Si) ligand-to-metal charge-transfer (LMCT) band in the SiO3(2-) group. The optical energy band gap is widened with increase of Eu3+ ion dopant.     

硅掺杂碳量子点荧光猝灭法测定水样中铜(Ⅱ)

3-氨丙基三甲氧基硅烷(APTMS)与戊二醛(GA)混合前驱物合成的硅掺杂碳量子点(SDCQDs),其最大吸收、激发和发射波长分别为259,245,395 nm,量子产率为13.60%,XPS谱图表明碳量子点掺杂Si,且富含甲亚胺基团和硅氧键。Cu~(2+)对碳量子点荧光产生猝灭作用,依据Cu~(2+)浓度与碳量子点荧光强度猝灭率的相关性,建立碳量子点荧光探针测定水样中Cu~(2+)的分析方法,其它金属离子对Cu~(2+)干扰程度较小,回收率为91.4%~100.8%,检出限为0.13μmol/L,相对标准偏差为0.20%~0.92%。     

对—苯二甲酸邻菲罗啉铕镧配合物的红外光谱及荧光光谱研究

用对-苯二甲酸铵和邻菲罗啉与氯化铕和氯化镧在乙醇-水溶液中反应,合成了对-苯二甲酸邻菲罗啉铕镧异核稀土配合物,测定了配合物的C,H,N和稀土元素的含量、红外光谱、紫外光谱及荧光光谱,确定了配合物的组成。结果表明,羧基氧和邻菲罗啉氮原子均与稀土离子配位,桥联配体对-苯二甲酸根可有效的传送能量,不发光的镧离子对铕离子的发光有明显的增强作用。     

Novel class of aeschynite structure LaNbTiO6-based orange-red phosphors via a modified combustion approach

A novel class of orange-red phosphors based on Eu(3+)-activated LaNbTiO(6) was successfully fabricated by a wet chemical method, called a modified combustion approach. XRD, TG-DTA, SEM, and EDS results show that the heat-treatment of the powders above 1000 degrees C is enough to obtain highly crystallized and phase-pure LaNbTiO(6) and Eu(3+)-doped samples, which is of prime importance in investigating the optical properties of the novel phosphors using LaNbTiO(6) as the host material. UV-vis diffuse reflectance spectroscopy reveals that the direct band gap of LaNbTiO(6) with large grains (above 200 nm) is calculated to be 3.27 eV, while the absorption edge of the small particles shows an obvious blue-shift. Two blue emission bands centered at 440 and 470 nm ascribed to the self-trapped exciton emission of the distorted NbO(6) and TiO(6) groups for the pure LaNbTiO(6) can be obtained. Photoluminescence spectra of the Eu(3+)-doped phosphor particles illuminated the simultaneous occurrence of several intense orange-red band emissions due to the characteristic transitions of (5)D(0,1) --> (7)F(J) (J = 0, 1, 2, 3, 4) of Eu(3+) under 395 nm excitation. The mechanism of these multiplets possibly arising from the odd-parity distortions of the Eu(3+) ion environment and the effect of crystallanity of the compounds on luminescence were discussed, respectively. The highly bright and color-uniform fluorescence images of the doped samples with short luminescence decay times (nanosecond magnitude) confirmed the potential applications of the phosphors in luminescence and display devices.     

Highly uniform and monodisperse beta-NaYF(4):Ln(3+) (Ln = Eu, Tb, Yb/Er, and Yb/Tm) hexagonal microprism crystals: hydrothermal synthesis and luminescent properties

beta-NaYF4:Ln3+ (Ln = Eu, Tb, Yb/Er, and Yb/Tm) hexagonal microprisms with remarkably uniform morphology and size have been synthesized via a facile hydrothermal route. X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), and photoluminescence (PL) spectra as well as kinetic decays were used to characterize the samples. It is found that sodium citrate as a shape modifier introduced into the reaction system plays a critical role in the shape evolution of the final products. Furthermore, the shape and size of the products can be further manipulated by adjusting the molar ratio of citrate/RE3+ (RE represents the total amount of Y3+ and the doped rare earth elements such as Eu3+, Tb3+, Yb3+/Er3+, or Yb3+/Tm3+). Under the excitation of 397 nm ultraviolet light, NaYF4:xEu3+ (x = 1.5, 5%) shows the emission lines of Eu3+ corresponding to 5D0-3 --> 7FJ (J = 0-4) transitions from 400 to 700 nm (whole visible spectral region) with different intensity, resulting in yellow and red down-conversion (DC) light emissions, respectively. When doped with 5% Tb3+ ions, the strong DC fluorescence corresponding to 5D4 --> 7FJ (J = 6, 5, 4, 3) transitions with 5D4 --> 7F5 (green emission at 544 nm) being the most prominent group that has been observed. In addition, under 980 nm laser excitation, the Yb3+/Er3+- and Yb3+/Tm3+-codoped beta-NaYF4 samples exhibit bright green and whitish blue up-conversion (UC) luminescence, respectively. The luminescence mechanisms for the doped lanthanide ions were thoroughly analyzed.     

Cd2+掺杂ZnWO4纳米棒的合成和光致发光性能研究

采用简单的水热法合成了Cd2+掺杂ZnWO4纳米棒.通过SEM、TEM、EDX和XRD等手段对产物进行了表征.实验结果表明,产物为直径约20 nm.长300～500 nm的Cd2+掺杂ZnWO4纳米棒.研究了Cd2+掺杂量对ZnWO4纳米棒的光致发光性能的影响,随着Cd2+掺杂量的增加,ZnWO4纳米棒的光致发光强度随之增强.     

Sol–gel synthesis of Eu<Superscript>3+</Superscript>: Tb<Subscript>3</Subscript>Al<Subscript>5</Subscript>O<Subscript>12</Subscript> nanophosphor

Eu (0.1, 0.5 and 1.0 mol%) doped Tb₃Al₅O₁₂ (TAG) was prepared by sol–gel technique through nitrate-citrate route followed by sintering in air (1,100 °C maximum temperature). XRD analysis showed that Eu³⁺ enters the TAG lattice substitutionally replacing the Tb³⁺ ion. Both XRD as well as FTIR investigation showed improvement in crystalline phase with the increase in the sintering temperature. SEM and TEM analysis showed that the powder contains the particles in 5–20 nm size with almost spherical morphology. The excitation spectrum recorded in 300–500 nm showed dominant absorption due to Tb³⁺ while the emission spectra recorded with 380 nm excitation had strong red emission characteristic of Eu³⁺. The intensity of this emission increases with the increase of the Eu concentration from 0.1 to 0.5 mol%. However, the emission intensity decreased on further increase in Eu concentration to 1.0 mol%. This intensity variation with dopant concentration is attributed to well-known “concentration quenching” observed in rare-earth doped materials. Reasonably strong red emission due to Eu was observed when excited with the blue (480 nm) radiation of a Xe lamp indicating the usefulness of the material for the realization of white light LED.     

Microwave synthesis and characterization of europium complexes with cinnamic acid and phenanthroline

We report here the synthesis and characterization of a host of Eu(Phen)L₃ with cinnamic acid (C₆H₅CH = CHCOOH, HL) and phenanthroline (Phen), and employing microwave radiation, where the microwave radiation is used just for the uniform heating of the reaction mixture. Its IR absorption spectra, scanning electron microscopy (SEM), and fluorescence spectra were studied. The results show that the particles of Eu(Phen)L₃ phosphors are basically spherical in shape, with good dispersing. The mean particle size is 1–2 μm. The excitation spectrum is a broad band and the main peak is at 320.0 nm. Moreover, excitation peak at 396.0 nm was found in the excitation spectrum. The emission spectrum shows that Eu(Phen)L₃ has narrow emission peaks. The emission peaks are ascribed to Eu³⁺ ions transition from ⁵ D _J (J = 0) to ⁷ F _J (J = 1, 2, 4). However, the strongest main emission peak locates at 614.0 nm, which corresponds to the electric dipole transition of Eu³⁺(⁵ D ₀ → ⁷ F ₂) The article is published in the original.