Melt block copolymerization of ϵ-caprolactone and L-lactide

AB block copolymers of ϵ-caprolactone and (L )-lactide could be prepared by ring-opening polymerization in the melt at 110°C using stannous octoate as a catalyst and ethanol as an initiator provided ϵ-caprolactone was polymerized first. Ethanol initiated the polymerization of ϵ-caprolactone producing a polymer with ϵ-caprolactone derived hydroxyl end groups which after addition of L -lactide in the second step of the polymerization initiated the ring-opening copolymerization of L -lactide. The number-average molecular weights of the poly(ϵ-caprolactone) blocks varied from 1.5 to 5.2 × 10³, while those of the poly(L -lactide) blocks ranged from 17.4 to 49.7 × 10³. The polydispersities of the block copolymers varied from 1.16 to 1.27. The number-average molecular weights of the polymers were controlled by the monomer/hydroxyl group ratio, and were independent on the monomer/stannous octoate ratio within the range of experimental conditions studied. When L -lactide was polymerized first, followed by copolymerization of ϵ-caprolactone, random copolymers were obtained. The formation of random copolymers was attributed to the occurrence of transesterification reactions. These side reactions were caused by the ϵ-caprolactone derived hydroxyl end groups generated during the copolymerization of ϵ-caprolactone with pre-polymers of L -lactide. The polymerization proceeds through an ester alcoholysis reaction mechanism, in which the stannous octoate activated ester groups of the monomers react with hydroxyl groups. © 1997 John Wiley & Sons, Inc.     

Synthesis and characterization of poly(L‐lactide‐co‐ε‐caprolactone) (B)‐poly(L‐lactide) (A) ABA block copolymers

ABA triblock copolymers of L ‐lactide (LL) and ε‐caprolactone (CL), designated as PLL‐P(LL‐co‐CL)‐PLL, were synthesized via a two‐step ring‐opening polymerization in bulk using diethylene glycol and stannous octoate as the initiating system. In the first‐step reaction, an approximately 50:50 mol% P(LL‐co‐CL) random copolymer (prepolymer) was prepared as the middle (B) block. This was then chain extended in the second‐step reaction by terminal block polymerization with more L ‐lactide. The percentage yields of the triblock copolymers were in excess of 95%. The prepolymers and triblock copolymers were characterized using a combination of dilute‐solution viscometry, gel permeation chromatography (GPC), ¹H‐ and ¹³C‐NMR, and differential scanning calorimetry (DSC). It was found that the molecular weight of the prepolymer was controlled primarily by the diethylene glycol concentration. All of the triblock copolymers had molecular weights higher than their respective prepolymers. ¹³C‐NMR analysis confirmed that the prepolymers contained at least some random character and that the triblock copolymers consisted of additional terminal PLL end (A) blocks. From their DSC curves, the triblock copolymers were seen to be semi‐crystalline in morphology. Their glass transition, solid‐state crystallization, and melting temperature ranges, together with their heats of melting, all increased as the PLL end (A) block length increased. Copyright © 2005 John Wiley & Sons, Ltd.     

Synthesis and characterization of tercopolymers derived from ε‐caprolactone,trimethylene carbonate,and lactide

A series of tri‐components copolymers with different molar ratios were synthesized via bulk ring‐opening copolymerization of trimethylene carbonate (TMC), L ‐lactide (LLA), and ε‐caprolactone (ε‐CL), using stannous octoate as catalyst. The sequence structure of the tercopolymer chain was characterized by ¹H and ¹³C nuclear magnetic resonance (NMR), Fourier transform infrared (FTIR), and gel permeation chromatography (GPC). The results showed that although block sequence of the corresponding monomers still existed in the tercopolymer chain, the random tercopolymers were ultimately obtained due to the transesterification during polymerization. For the samples TP1 and TP2, longer sequence of LLA existed in the molecular chains. The thermal properties of tercopolymers were investigated by differential scanning calorimetry (DSC) and the mechanical properties of the resulting copolymers were studied by using a tensile tester. The results indicated that the properties of these copolymers could be adjusted by changing the compositions of the copolymers. The resulting tercopolymers are expected to have potential uses as nerve regeneration and other biomedicine materials. Copyright © 2007 John Wiley & Sons, Ltd.     

Preparation of novel poly(ethylene oxide‐co‐glycidol)‐graft‐poly(ε‐caprolactone) copolymers and inclusion complexation of the grafted chains with α‐cyclodextrin

A well‐defined comblike copolymer of poly(ethylene oxide‐co‐glycidol) [(poly(EO‐co‐Gly)] as the main chain and poly(ε‐caprolactone) (PCL) as the side chain was successfully prepared by the combination of anionic polymerization and ring‐opening polymerization. The glycidol was protected by ethyl vinyl ether to form 2,3‐epoxypropyl‐1‐ethoxyethyl ether (EPEE) first, and then ethylene oxide was copolymerized with EPEE by an anionic mechanism. The EPEE segments of the copolymer were deprotected by formic acid, and the glycidol segments of the copolymers were recovered after saponification. Poly(EO‐co‐Gly) with multihydroxyls was used further to initiate the ring‐opening polymerization of ε‐caprolactone in the presence of stannous octoate. When the grafted copolymer was mixed with α‐cyclodextrin, crystalline inclusion complexes (ICs) were formed, and the intermediate and final products, poly(ethylene oxide‐co‐glycidol)‐graft‐poly(ε‐caprolactone) and ICs, were characterized with gel permeation chromatography, NMR, differential scanning calorimetry, X‐ray diffraction, and thermogravimetric analysis in detail. The obtained ICs had a channel‐type crystalline structure, and the ratio of ε‐caprolactone units to α‐cyclodextrin for the ICs was higher than 1:1. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3684–3691, 2006     

Hydrolyzable poly(ester-urethane) networks from L-lysine diisocyanate and D,L-lactide/ϵ-caprolactone homo- and copolyester triols

Bioabsorbable poly(ester-urethane) networks were synthesized from ethyl 2,6-diisocyanatohexanoate (L -lysine diisocyanate) (LDI) and a series of polyester triols. LDI was synthesized by refluxing L-lysine monohydrochloride with ethanol to form the ester, which was subsequently refluxed with 1,1,1,3,3,3-hexamethyldisilazane to yield a silazane-protected intermediate. This product was then phosgenated using triphosgene. Polyester triols were synthesized from D,L-lactide, ?-caprolactone, or comonomer mixtures thereof, using glycerol as initiator and stannous octoate as catalyst. Polyurethane networks were cured using [NCO]/[OH] = 1.05 and stannous octoate (0.05 wt %) for 24 h at room temperature and pressure and 24 h at 50°C and 0.1 mm Hg. LDI-based polyurethane networks were totally amorphous and possessed very low sol contents. Networks based on poly (D,L-lactide) triols were rigid (T_g ∽ 60°C) with ultimate tensile strengths of ～ 40–70 MPa, tensile moduli of ～ 1.2–2.0 GPa, and ultimate elongations of ～ 4–10%. Networks based on ?-caprolactone triols were low-modulus elastomers with tensile strengths and moduli of ～ 1–4 MPa and ～ 3–6 GPa, respectively, and ultimate elongations of ～ 50–300%. Networks based on copolymers displayed physical properties consistent with monomer composition and were tougher than the networks based on the homopolymers. Tensile strengths for the copolymers were ～ 3–25 MPa with ultimate elongations up to 600%. Hydrolytic degradation under simulated physiological conditions showed that D ,L -lactide homopolymer networks were the most resistant to degradation, undergoing virtually no change in mass or physical properties for 60 days. ?-Caprolactone-based networks were resistant to degradation for 40 days, and high-lactide copolymer-based networks suffered substantial losses in physical properties after only 3 days. © 1994 John Wiley & Sons, Inc.     

Fast degradable poly(L‐lactide‐co‐ε‐caprolactone) microspheres for tissue engineering: Synthesis,characterization, and degradation behavior

Polymeric scaffolds play a crucial role in engineering process of new tissues and effect the cell growth and viability. PLCL copolymers are found to be very useful during cell growth due to their elastic behavior and mechanical strength. Thus, low molecular weight PLCL copolymers of various ratios viz. PLCL(90/10), PLCL(75/25), PLCL(50/50) and PCL were synthesized by ring opening polymerization using stannous octoate as a catalyst. Synthesized polymers were characterized by GPC, ¹H‐NMR, FTIR and XRD. The thermal properties of the copolymers were studied using TGA and DSC. Microspheres of about 100 μm diameter were prepared for different copolymers and their in vitro degradation behaviors were studied up to 108 days. It was observed that degradation of PLA content in polymer backbone occurs faster than PCL component which is also indicated by corresponding change in ratios of PLA/PCL, as determined by ¹H‐NMR. SEM images of microspheres depicted the surface morphology during degradation and suggested the faster degradation for PLCL (50:50). Copolymers of different thermal, mechanical properties and different degradation behaviors can be prepared by adjusting the composition of copolymers. Various synthesized polymers from this work have been tested in our laboratory as polymeric scaffold for soft tissue engineering. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2755–2764, 2007     

Hydrolytic degradation of polyester–polyether block copolymer based on polycaprolactone/poly(ethylene glycol)/polylactide

Polyester–polyether block copolymers based on polycaprolactone/poly(ethylene glycol)/polylactide (PCEL) with various compositions were synthesized by direct copolymerization of ϵ‐caprolactone, L ‐lactide and PEG (6000) in the presence of stannous octoate at 130 °C for 56 hr. The degradation behavior of the copolymers was investigated in a pH 7.4 phosphate buffer solution at 37 ±1 °C. Various techniques such as weight, gel permeation chromatography, ¹H nuclear magnetic resonance, differential scanning calorimetry and X‐ray diffractometry were used to monitor the changes in water absorption, weight loss, molar mass, molar mass distribution, thermal properties and compositions. The results show that the hydrophilicity of copolymer was enhanced with increasing poly(ethylene oxide) content, which led to the PEG sequences fast release and an increase in weight loss of the copolymer. Bimodal chromatograms were detected in the degradation, which were attributed to the degradation mechanism of the partial crystalline polymer proceeding predominantly in amorphous zones. Copyright © 2000 John Wiley & Sons, Ltd.     

Microstructure analysis and thermal property of copolymers made of glycolide and ϵ‐caprolactone by stannous octoate

Glycolide (GL) and ?‐caprolactone (CL) were copolymerized in bulk at relatively high temperatures using stannous octoate as a catalyst. To investigate the relationship among microstructure, thermal properties, and crystallinity, three series of copolymers prepared at various reaction temperatures, times, and comonomer feed ratios were prepared and characterized by ¹H and ¹³C NMR, DSC, and wide‐angle X‐ray diffraction (WAXD). The 600‐MHz ¹H NMR spectra provided information about not only the copolymer compositions but also about the chain microstructure. The reactivity ratios (r_G and r_C) were calculated from the monomer sequences and were 6.84 and 0.13, respectively. In terms of overall feed compositions, the sequence lengths of the glycolyl units calculated from the reactivity ratios exceeded those measured from the polymeric products. Mechanistic considerations based on reactivity ratios, monomer consumption data, and average sequence lengths are discussed. The unusual phase diagram of GL/CL copolymers implies that the copolymer melting temperature does not depend on its composition alone but rather on the nature of the sequence distribution. The DSC and WAXD measurements show a close relationship between polymer crystallinity and the nature of the polymer sequence. © 2002 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 544–554, 2002; DOI 10.1002/pola.10123     

Synthesis and Characterization of Poly(ε-caprolactone-co-δ-valerolactone) with Pendant Carboxylic Functional Groups

In this paper, aliphatic polyesters functionalized with pendant carboxylic groups were synthesized via several steps. Firstly, substituted cyclic ketone, 2‐(benzyloxycarbonyl methyl)cyclopentanone (BCP) was prepared through the reaction of enamine with benzyl‐2‐bromoacetate, and subsequently converted into the relevant functionalized δ‐valerolactone derivative, 5‐(benzyloxy carbonylmethyl)‐δ‐valerolactone (BVL) by the Baeyer‐Villiger oxidation. Secondly, the ring‐opening polymerization of BVL with ε‐caprolactone was carried out in bulk using stannous octoate as the catalyst to produce poly(ε‐caprolactone‐co‐δ‐valerolactone) bearing the benzyl‐protected carboxyl functional groups [P(CL‐co‐BVL)]. Finally, the benzyl‐protecting groups of P(CL‐co‐BVL) were effectively removed by H₂ using Pd/C as the catalyst to obtain poly(ε‐caprolactone‐co‐δ‐valerolactone) bearing pendant carboxylic acids [P(CL‐co‐CVL)]. The structure and the properties of the polymer have been studied by Nuclear Magnetic Resonance (NMR), Fourier Infrared Spectroscopy (FT‐IR) and Differential Scan Calorimetry (DSC) etc. The NMR and FT‐IR results confirmed the polymer structure, and the ¹³C NMR spectra have clearly interpreted the sequence of ε‐caprolactone and 5‐(benzyloxycarbonylmethyl)‐δ‐valerolactone in the copolymer. When the benzyl‐protecting groups were removed, the aliphatic polyesters bearing carboxylic groups were obtained. Moreover, the hydrophilicity of the polymer was improved. Thus, poly(ε‐caprolactone‐co‐δ‐valerolactone) might have great potential in biomedical fields.     

Synthesis and characterization of poly(β‐hydroxybutyrate) and poly(ϵ‐caprolactone) copolyester by transesterification

To synthesize the copolyester of poly(β‐hydroxybutyrate) (PHB) and poly(?‐caprolactone) (PCL), the transesterification of PHB and PCL was carried out in the liquid phase with stannous octoate as the catalyzer. The effects of reaction conditions on the transesterification, including catalyzer concentration, reaction temperature, and reaction time, were investigated. The results showed that both rising reaction temperature and increasing reaction time were advantageous to the transesterification. The sequence distribution, thermal behavior, and thermal stability of the copolyesters were investigated by ¹³C NMR, Fourier transform infrared spectroscopy, differential scanning calorimetry, wide‐angle X‐ray diffraction, optical microscopy, and thermogravimetric analysis. The transesterification of PHB and PCL was confirmed to produce the block copolymers. With an increasing PCL content in the copolyesters, the thermal behavior of the copolyesters changed evidently. However, the introduction of PCL segments into PHB chains did not affect its crystalline structure. Moreover, thermal stability of the copolyesters was little improved in air as compared with that of pure PHB. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1893–1903, 2002     

Synthesis and characterization of amphiphilic copolymer of linear poly(ethylene oxide) linked with [poly(styrene‐co‐2‐hydroxyethyl methacrylate)‐graft‐poly(ε‐caprolactone)] using sequential controlled polymerization

A well‐defined amphiphilic copolymer of ‐poly(ethylene oxide) (PEO) linked with comb‐shaped [poly(styrene‐co‐2‐hydeoxyethyl methacrylate)‐graft‐poly(ε‐caprolactone)] (PEO‐b‐P(St‐co‐HEMA)‐g‐PCL) was successfully synthesized by combination of reversible addition‐fragmentation chain transfer polymerization (RAFT) with ring‐opening anionic polymerization and coordination–insertion ring‐opening polymerization (ROP). The α‐methoxy poly(ethylene oxide) (mPEO) with ω,3‐benzylsulfanylthiocarbonylsufanylpropionic acid (BSPA) end group (mPEO‐BSPA) was prepared by the reaction of mPEO with 3‐benzylsulfanylthiocarbonylsufanyl propionic acid chloride (BSPAC), and the reaction efficiency was close to 100%; then the mPEO‐BSPA was used as a macro‐RAFT agent for the copolymerization of styrene (St) and 2‐hydroxyethyl methacrylate (HEMA) using 2,2‐azobisisobutyronitrile as initiator. The molecular weight of copolymer PEO‐b‐P(St‐co‐HEMA) increased with the monomer conversion, but the molecular weight distribution was a little wide. The influence of molecular weight of macro‐RAFT agent on the polymerization procedure was discussed. The ROP of ε‐caprolactone was then completed by initiation of hydroxyl groups of the PEO‐b‐P(St‐co‐HEMA) precursors in the presence of stannous octoate (Sn(Oct)₂). Thus, the amphiphilic copolymer of linear PEO linked with comb‐like P(St‐co‐HEMA)‐g‐PCL was obtained. The final and intermediate products were characterized in detail by NMR, GPC, and UV. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 467–476, 2006     

Stannous oxalate: An efficient catalyst for poly(trimethylene terephthalate) synthesis

A complete study on the catalytic activity of stannous oxalate for poly(trimethylene terephthalate) (PTT) synthesis via esterification method is carried out by comparison to the well known catalysts (tetrabutyl titanate (TBT), dibutyltin oxide (Bu2SnO), and stannous octoate (SOC)). Their catalytic activity in the esterification process is monitored by measuring the amount of water generated, while intrinsic viscosity (IV) and content of terminal carboxyl groups (CTCG) are used as the index in the polycondensation process. Stannous oxalate shows higher activity than the other catalysts. Decrease in reaction time and improvements in PTT property are observed. The higher catalytic activity of stannous oxalate is attributed to its chelate molecular structure.     

Efficient zinc initiators supported by NNO‐tridentate ketiminate ligands for cyclic esters polymerization

A series of zinc benzylalkoxide complexes, [LⁿZn(μ‐OBn)]₂ (L = L ¹ H – L ⁵ H ), supported by NNO‐tridentate ketiminate ligands with various electron withdrawing‐donating subsituents have been synthesized and characterized. X‐ray crystal structural studies revealed that complexes 2b and 4b are dinuclear bridging through the benzylalkoxy oxygen atoms with penta‐coordinated metal centers. All the metal complexes have acted as efficient initiators for the ring‐opening polymerization of L ‐lactide (within 12 min, 0 °C). Remarkably, a molecular weight of PLLA up to 580,000 can be achieved using [(L⁵Zn(μ‐OBn)]₂ ( 5b ) as an initiator. The kinetic studies for the polymerization of L ‐lactide with complex 3b at ?10 °C corresponded to first‐order reactions in the monomer. The ring‐opening polymerization (ROP) of ε‐caprolactone, ε‐decalactone, β‐butyrolactone and their copolymer with complex 3b was investigated. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Polymer-Attached Thiazolium Salts-Catalyzed Addition of Aldehydes to α, β-Unsaturated Carbonyl Compounds

A homogeneous catalyst, 3-benzyl-5-(2-hydroxyethyl)-4-methyl-1,3-thiazolium chloride, for addition of aldehydes to activated double bond, was attached to 20% cross-linked polystyrene-divinylbenzene copolymer. The attached catalysts could be easily removed from the reaction mixture. Polymer-attached thiazolium salts in the presence of triethylamine are active catalysts for addition of aromatic and aliphatic aldehydes to α,β-unsaturated ketones to yield γ-diketones.     

Preparation and characterization of biodegradable poly(trimethylenecarbonate‐ε‐caprolactone)‐block‐poly(p‐dioxanone) copolymers

A series of poly(trimethylenecarbonate‐ε‐caprolactone)‐block‐poly(p‐dioxanone) copolymers were prepared with varying feed rations by using two step polymerization reactions. Poly(trimethylenecarbonate)(ε‐caprolactone) random copolymer was synthesized with stannous‐2‐ethylhexanoate and followed by adding p‐dioxanone monomer as the other block. The ring opening polymerization was carried out at high temperature and long reaction time to get high molecular weight polymers. The monofilament fibers were obtained using conventional melting spun methods. The copolymers were identified by ¹H and ¹³C NMR spectroscopy and gel permeation chromatography (GPC). The physicochemical properties, such as viscosity, molecular weight, melting point, glass transition temperature, and crystallinity, were studied. The hydrolytic degradation of copolymers was studied in a phosphate buffer solution, pH = 7.2, 37 °C, and a biological absorbable test was performed in rats. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2790–2799, 2005     

Mixed iridium(III) and ruthenium(II) polypyridyl complexes containing poly(ε‐caprolactone)‐bipyridine macroligands

A hydroxy‐functionalized bipyridine ligand was polymerized with ε‐caprolactone utilizing the controlled ring‐opening polymerization of ε‐caprolactone in the presence of stannous octoate. The resulting poly(ε‐caprolactone)‐containing bipyridine was characterized by ¹H NMR and IR spectroscopy, and gel permeation chromatography, as well as matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry, revealing the successful incorporation of the bipyridine ligand into the polymer chain. Coordination to iridium(III) and ruthenium(II) precursor complexes yielded two macroligand complexes, which were characterized by NMR, gel permeation chromatography, matrix‐assisted laser desorption/ionization time‐of‐flight MS, cyclic voltammetry, and differential scanning calorimetry. In addition, both photophysical and electrochemical properties of the metal‐containing polymers proved the formation of a trisruthenium(II) and a trisiridium(III) polypyridyl species, respectively. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4153–4160, 2004     

Synthesis and characterization of well‐defined poly(2‐hydroxyethyl methacrylate‐co‐styrene)‐graft‐poly(ε‐caprolactone) by sequential controlled polymerization

A new graft copolymer, poly(2‐hydroxyethyl methacrylate‐co‐styrene) ‐graft‐poly(?‐caprolactone), was prepared by combination of reversible addition‐fragmentation chain transfer polymerization (RAFT) with coordination‐insertion ring‐opening polymerization (ROP). The copolymerization of styrene (St) and 2‐hydroxyethyl methacrylate (HEMA) was carried out at 60 °C in the presence of 2‐phenylprop‐2‐yl dithiobenzoate (PPDTB) using AIBN as initiator. The molecular weight of poly (2‐hydroxyethyl methacrylate‐co‐styrene) [poly(HEMA‐co‐St)] increased with the monomer conversion, and the molecular weight distribution was in the range of 1.09 ～ 1.39. The ring‐opening polymerization (ROP) of ?‐caprolactone was then initiated by the hydroxyl groups of the poly(HEMA‐co‐St) precursors in the presence of stannous octoate (Sn(Oct)₂). GPC and ¹H‐NMR data demonstrated the polymerization courses are under control, and nearly all hydroxyl groups took part in the initiation. The efficiency of grafting was very high. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5523–5529, 2004     

One‐pot inimer promoted ROCP synthesis of branched copolyesters using α‐hydroxy‐γ‐butyrolactone as the branching reagent

An array of branched poly(?‐caprolactone)s was successfully synthesized using an one‐pot inimer promoted ring‐opening multibranching copolymerization (ROCP) reaction. The biorenewable, commercially available yet unexploited comonomer and initiator 2‐hydroxy‐γ‐butyrolactone was chosen as the inimer to extend the use of 5‐membered lactones to branched structures and simultaneously avoiding the typical tedious work involved in the inimer preparation. Reactions were carried out both in bulk and in solution using stannous octoate (Sn(Oct)₂) as the catalyst. Polymerizations with inimer equivalents varying from 0.01 to 0.2 were conducted which resulted in polymers with a degree of branching ranging from 0.049 to 0.124. Detailed ROCP kinetics of different inimer systems were compared to illustrate the branch formation mechanism. The resulting polymer structures were confirmed by ¹H, ¹³C, and ₁H‐₁₃C HSQC NMR and SEC (RI detector and triple detectors). The thermal properties of polymers with different degree of branching were investigated by DSC, confirming the branch formation. Through this work, we have extended the current use of the non‐homopolymerizable γ‐butyrolactone to the branched polymers and thoroughly examined its behaviors in ROCP. © 2016 The Authors. Journal of Polymer Science Part A: Polymer Chemistry Published by Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1908–1918     

Synthesis of star‐shaped poly(D,L‐lactic acid‐alt‐glycolic acid)‐b‐poly(L‐lactic acid) with the poly(D,L‐lactic acid‐alt‐glycolic acid) macroinitiator and stannous octoate catalyst

Two types of three‐arm and four‐arm, star‐shaped poly(D,L ‐lactic acid‐alt‐glycolic acid)‐b‐poly(L ‐lactic acid) (D,L ‐PLGA50‐b‐PLLA) were successfully synthesized via the sequential ring‐opening polymerization of D,L ‐3‐methylglycolide (MG) and L ‐lactide (L ‐LA) with a multifunctional initiator, such as trimethylolpropane and pentaerythritol, and stannous octoate (SnOct₂) as a catalyst. Star‐shaped, hydroxy‐terminated poly(D,L ‐lactic acid‐alt‐glycolic acid) (D,L ‐PLGA50) obtained from the polymerization of MG was used as a macroinitiator to initiate the block polymerization of L ‐LA with the SnOct₂ catalyst in bulk at 130 °C. For the polymerization of L ‐LA with the three‐arm, star‐shaped D,L ‐PLGA50 macroinitiator (number‐average molecular weight = 6800) and the SnOct₂ catalyst, the molecular weight of the resulting D,L ‐PLGA50‐b‐PLLA polymer linearly increased from 12,600 to 27,400 with the increasing molar ratio (1:1 to 3:1) of L ‐LA to MG, and the molecular weight distribution was rather narrow (weight‐average molecular weight/number‐average molecular weight = 1.09–1.15). The ¹H NMR spectrum of the D,L ‐PLGA50‐b‐PLLA block copolymer showed that the molecular weight and unit composition of the block copolymer were controlled by the molar ratio of L ‐LA to the macroinitiator. The ¹³C NMR spectrum of the block copolymer clearly showed its diblock structures, that is, D,L ‐PLGA50 as the first block and poly(L ‐lactic acid) as the second block. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 409–415, 2002     

Drug release and biocompatibility of self‐assembled micelles prepared from poly (ɛ‐caprolactone/glycolide)‐poly (ethylene glycol) block copolymers

A series of poly(?‐caprolactone/glycolide)‐poly(ethylene glycol) (P(CL/GA)‐PEG) diblock copolymers were prepared by ring opening polymerization of a mixture of ?‐caprolactone and glycolide using mPEG as macro‐initiator and stannous octoate as catalyst. Self‐assembled micelles were prepared from the copolymers using nanoprecipitation method. The micelles were spherical in shape. The micelle size was larger for copolymers with longer PEG blocks. In contrast, the critical micelle concentration of copolymers increased with decreasing the overall hydrophobic block length. Drug loading and drug release studies were performed under in vitro conditions, using paclitaxel as a hydrophobic model drug. Higher drug loading was obtained for micelles with longer poly(ε‐caprolactone) blocks. Faster drug release was obtained for micelles of mPEG2000 initiated copolymers than those of mPEG5000 initiated ones. Higher GA content in the copolymers led to faster drug release. Moreover, drug release rate was enhanced in the presence of lipase from Pseudomonas sp., indicating that drug release is facilitated by copolymer degradation. The biocompatibility of copolymers was evaluated from hemolysis, dynamic clotting time, and plasma recalcification time tests, as well as MTT assay and agar diffusion test. Data showed that copolymer micelles present outstanding hemocompatibility and cytocompatibility, thus suggesting that P(CL/GA)‐PEG micelles are promising for prolonged release of hydrophobic drugs.