可分散性纳米SiO2/尼龙1010复合材料的结晶行为

采用熔融共混法制备了可分散性纳米SiO2/尼龙1010复合材料.通过X射线衍射和差示扫描量热法对尼龙1010及其复合材料的结晶行为进行了研究.结果表明,SiO2的加入作为结晶的异相成核点,使复合材料的结晶温度升高,熔融温度降低,使其结晶度稍有降低;SiO2的加入并没有改变尼龙1010的结晶形态,只是使尼龙1010的晶格尺寸发生了一定程度的改变.     

超临界CO2溶胀聚合法制备聚丙烯酸/尼龙1313及聚苯乙烯/尼龙1313共混物

超临界CO2溶胀聚合法制备聚丙烯酸/尼龙1313及聚苯乙烯/尼龙1313共混物;超临界CO2;聚丙烯酸;聚苯乙烯;尼龙1313;共混     

尼龙-1010非等温结晶动力学

<正> 尼龙-1010是我国独创的工程塑料品种,已被较广泛地应用于精密机械零件、仪表制造、家用电器、航空等方面。有关尼龙-1010的基础研究大多在我国学者中间进行,由于在实际加工生产过程中,如通常的融熔纺丝、注射、模压等工艺均是在非等温条件下进行,有关它的非等温结晶动力学尚未见报道,本文用几种理论方法对尼龙-1010的非等温结晶动力学过程进行研究。     

碳纤维-尼龙1010界面形态的研究

通过偏光显微镜,研究了碳纤维-尼龙1010的界面形态,发现石墨、高模量碳纤维(M40)诱发尼龙1010形成横晶的能力大于高强度、中强度碳纤维;界面横晶形态强烈地依赖于结晶温度。     

聚合物在高压CO2条件下的结晶行为

高压CO2，包括超临界CO2，为人们研究聚合物的结晶行为提供了新的思路和方法。本文综述了聚合物在高压CO2条件下的吸收及其结晶行为等方面的研究进展。     

马来酸酐改性聚乙烯／尼龙1010共混体系的结晶行为

在尼龙-1010与马来酸酐改性聚乙烯共混体系中,马来酸酐起结晶成核剂的作用,可显著加快共混物中尼龙-1010组份的结晶。共混物的混容性也略有改善。     

超临界CO_2下的聚合物结晶形态和动力学研究现状北大核心CSCD

聚合物结晶一直以来是高分子凝聚态研究的热点,随着超临界流体尤其是超临界CO2(scCO2)在聚合物方面应用日益增加,对超临界条件下的聚合物结晶研究显得更加重要。scCO2在聚合物中溶解度较高,增塑效果好,能显著降低玻璃化温度(Tg)和熔点(Tm),改变聚合物的晶体形态,并对动力学过程产生较大影响。因此,聚合物在scCO2条件下结晶行为的深入研究,在实际应用中起着重要的指导作用。本文对scCO2作用下的链型、晶体形态、共混物特点和结晶动力学过程的研究现状进行综述。     

尼龙1010骤冷退火样品的晶体结构

尼龙1010的晶体结构属三斜晶系.作者最近导出了X射线衍射法(WAXD)测定尼龙1010结晶度的公式,进而考查了等温结晶时结晶温度T_C对结晶度X_C、晶粒尺寸L_(100)和氢键面相对衍射强度R的影响.发现X_C和L_(100)均随T_C升高而增大,达196℃后又减小;而R与T_C的关系则相反,呈线性降低.结晶速率快有利于分子链在垂直于氢键面的(100)晶面生长,但R值却降低了.本文利用WAXD考查了尼龙1010不同骤冷退火条件样品的晶体结构.     

尼龙1010等温结晶球晶形态与生成条件研究

 本文利用偏光显微镜研究了等温结晶时尼龙1010球晶的形态与生成条件,发现在原始样品熔点附近或高于原始熔点以上温度结晶,主要生成暗、亮与带正环的负光性放射状球晶;熔点以下至195℃主要生成正放射状球晶;在较宽的温度范围内可生成混合光性放射状球晶,与少量的六瓣、两瓣、不对称四瓣形三种异常光性球晶;181℃以下主要生成正环状球晶.     

尼龙1010的拉伸结晶行为及Brill转变

通过示差扫描量热分析、广角X射线衍射及二维广角X射线衍射等手段研究了尼龙1010在不同的拉伸比率(λ)及拉伸温度(T<,b>)下拉伸诱导的晶体转变及结晶取向行为.结果表明.在拉伸条件下,尼龙1010易于从a晶型向δ'晶型转变,而拉伸比率的提高,有利于促进这种Brill转变.在相同的拉伸比率下,随着拉伸温度的提高,尼龙1...     

Effect of EVM/EVA‐g‐MAH ratio on the structure and properties of nylon 1010 blends

The nylon 1010/ethylene‐vinyl acetate rubber (EVM)/maleated ethylene‐vinyl acetate copolymers (EVA‐g‐MAH) ternary blends were prepared. The effect of EVM/EVA‐g‐MAH ratio on the toughness of blends was examined. A super tough nylon 1010 blends were obtained by the incorporation of both EVM and EVA‐g‐MAH. Impact essential work of fracture (EWF) model was used to characterize the fracture behavior of the blends. The nylon/EVM/EVA‐g‐MAH (80/15/5) blend had the highest total fracture energy at a given ligament length (5 mm) and the highest dissipative energy density among all the studied blends. Scanning electron microscopy images showed the EVM and EVA‐g‐MAH existed as spherical particles in nylon 1010 matrix and their size decreased gradually with increasing EVA‐g‐MAH content. Large plastic deformation was observed on the impact fracture surface of the nylon/EVM/EVA‐g‐MAH (80/15/5) blend and related to its high impact strength. Then with increasing EVA‐g‐MAH proportion, the matrix shear yielding of nylon/EVM/EVA‐g‐MAH blends became less obvious. EVM and EVA‐g‐MAH greatly increased the apparent viscosity of nylon 1010, especially at low shear rates. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 877–887, 2009     

Radiation effects on the immiscible polymer blend of nylon1010 and high-impact strength polystyrene (II): mechanical properties and morphology

The paper studies the morphology and mechanical properties of immiscible binary blends of the nylon 1010 and HIPS through the radiation crosslinking method. In this blend, the HIPS particles were the dispersed phases in the nylon1010 matrix. With increasing of dose, the elastic modulus increased. However, the tensile strength, elongation at break and the energy of fracture increased to a maximum at a dose of 0.34 MGy, then reduced with the increasing of dose. SEM photographs show that the hole sizes are not changed obviously at low dose and at high dose, remnants that cannot be dissolved in formic acid and THF can be observed in the holes and on the surface. TEM photographs showed that radiation destroys the rubber phases in the polymer blend.     

Toughening effect of ethylene‐vinyl acetate rubber on nylon 1010 compatibilized by maleated ethylene‐vinyl acetate copolymers

The toughening effect of ethylene‐vinyl acetate rubbers (EVM) with maleated ethylene‐vinyl acetate copolymers (EVA‐g‐MAH) on the nylon 1010 was investigated. The addition of 5 phr (per hundred nylon 1010) EVM increased the elongation at break of nylon 1010 to a great extent. The notched Izod impact strength of nylon/EVM blends increased with increasing EVM content. Scanning electron microscope showed that the EVM particle size was around 0.5 μm when the EVM content was 5 phr and increased with increasing EVM content. After the addition of EVA‐g‐MAH to nylon/EVM (100/20) blend, the average diameter of EVM particles decreased from more than 1 μm to 0.5–0.6 μm. EVA‐g‐MAH could improve the adhesion between nylon 1010 and EVM. A sharp brittle‐ductile transition (BDT) was observed when the interparticle distance was about 0.2 μm, independent of the addition of EVA‐g‐MAH. The notched Izod impact strength of nylon/EVM blends at low temperatures was measured and the BDT shifted toward low temperatures with increasing EVM or EVA‐g‐MAH content. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 434–444, 2009     

尼龙1010／尼龙6共聚物的表观相图研究

采用显微熔点法和ＤＳＣ测定了尼龙１０１０／尼龙６共聚物的表观相图；分析了投料比与链节结构单元含量的关系。最低熔点时尼龙１０１０／尼龙６的理论重量投料比为６０／４０，摩尔比为３３．３／６６．７，实验结果与此相近。     

Preparation of microcellular polypropylene/polystyrene blend foams with tunable cell structure

By using supercritical carbon dioxide (sc‐CO₂) as the physical foaming agent, microcellular foaming was carried out in a batch process from a wide range of immiscible polypropylene/polystyrene (PP/PS) blends with 10–70 wt% PS. The blends were prepared via melt processing in a twin‐screw extruder. The cell structure, cell size, and cell density of foamed PP/PS blends were investigated and explained by combining the blend phase morphology and morphological parameters with the foaming principle. It was demonstrated that all PP/PS blends exhibit much dramatically improved foamability than the PP, and significantly decreased cell size and obviously increased cell density than the PS. Moreover, the cell structure can be tunable via changing the blend composition. Foamed PP/PS blends with up to 30 wt% PS exhibit a closed‐cell structure. Among them, foamed PP/PS 90:10 and 80:20 blends have very small mean cell diameter (0.4 and 0.7 µm) and high cell density (8.3 × 10¹¹ and 6.4 × 10¹¹ cells/cm³). Both of blends exhibit nonuniform cell structure, in which most of small cells spread as “a string of beads.” Foamed PP/PS 70:30 blend shows the most uniform cell structure. Increase in the PS content to 50 wt% and especially 70 wt% transforms it to an irregular open‐cell structure. The cell structure of foamed PP/PS blends is strongly related to the blend phase morphology and the solubility of CO₂ in PP more than that in PS, which makes the PP serve as a CO₂ reservoir. Copyright © 2009 John Wiley & Sons, Ltd.     

Radiation effects on the immiscible polymer blend of nylon1010 and high-impact polystyrene (HIPS) I: Gel/dose curves,mathematical expectation theorem and thermal behaviour

This paper studies the radiation properties of the immiscible blend of nylon1010 and HIPS. The gel fraction increased with increasing radiation dose. The network was found mostly in nylon1010, the networks were also found in both nylon1010 and HIPS when the dose reaches 0.85 MGy or more. We used the Charleby–Pinner equation and the modified Zhang–Sun-Qian equation to simulate the relationship with the dose and the sol fraction. The latter equation fits well with these polymer blends and the relationship used by it showed better linearity than the one by the Charleby–Pinner equation. We also studied the conditions of formation of the network by the mathematical expectation theorem for the binary system. Thermal properties of polymer blend were observed by DSC curves. The crystallization temperature decreases with increasing dose because the cross-linking reaction inhibited the crystallization procession and destroyed the crystals. The melting temperature also reduced with increasing radiation dose. The dual melting peak gradually shifted to single peak and the high melting peak disappeared at high radiation dose. However, the radiation-induced crystallization was observed by the heat of fusion increasing at low radiation dose. On the other hand, the crystal will be damaged by radiation. A similar conclusion may be drawn by the DSC traces when the polymer blends were crystallized. When the radiation dose increases, the heat of fusion reduces dramatically and so does the heat of crystallization.     

CO2/离子液体体系热力学性质的分子动力学模拟

超临界CO2和离子液体(ILs)是两种绿色溶剂. 离子液体可以溶解超临界CO2, 而超临界CO2不能溶解离子液体. 由此设计构成的CO2/IL二元系统, 同时具备了超临界CO2和离子液体的许多优点: 既可以降低离子液体的粘度, 还便于相分离, 是新型的耦合绿色溶剂. 其物理化学性质对于设计反应、分离等过程非常重要. 因此, 本文以CO2/IL二元系统为研究对象, 通过选择合适的分子力场和系综, 运用分子动力学(MD)模拟方法研究了CO2/[bmim][PF6]、CO2/[bmim][NO3]等体系的热力学性质. 结果表明, CO2对ILs膨胀度的影响非常小, 当CO2摩尔分数为0.5时, ILs膨胀仅为15%. CO2/ILs的扩散系数远小于CO2膨胀甲醇、乙醇溶液的扩散系数. 随着CO2含量的增加, ILs的扩散系数提高, 粘度显著下降, 表明CO2能有效地改善ILs扩散性, 减小其粘度. 因此CO2可用以改善离子液体溶剂体系的传递特性, 增强反应分离过程在其中的进行.     

刚性粒子增韧尼龙1010体系的研究

采用扫描电镜和动态力学等研究了在磺化聚苯乙烯（ＨＳＰＳ）作用下，尼龙１０１０（ＰＡ１０１０）／聚苯乙烯（ＰＳ）共混物的形态及相容性。结果表明，ＨＳＰＳ的加入显著改善了ＰＳ与ＰＡ１０１０的相容性，加强了界面粘结，使共混物缺口冲击明显提高，实现了ＰＳ增韧ＰＡ１０１０的目标。偏光显微竟结盟表明，ＨＳＰＳ的加入对共混物中ＰＡ１０１０的结晶形态有明显影响，使ＰＡ１０１０球晶细化且不完善。