侧链含氨基的PLGA-(PEGA-SP)_n共聚物的合成与表征

以聚乙二醇(PEG)和N -苄氧羰基 -L- 天冬氨酸酐为原料,通过溶液缩聚法制备了聚(聚乙二醇 -co -L -天冬氨酸)交替预聚物(PEG- ASP) n;进一步以辛酸亚锡为催化剂、(PEG- ASP) n 为共引发剂引发D ,L- LA和GA开环共聚合成了带有侧氨基功能基团的PLGA (PEG- ASP) n 共聚物.用GPC、FT -IR、1 H -NMR、DSC等研究了共聚物的结构和性能.结果表明,共聚物表现为典型的无定形聚合物;(PEG- ASP) n 的含量对共聚物的性能有显著影响,随(PEG- ASP) n 含量增加,共聚物的亲水性增强,玻璃化转变温度(Tg)下降;以Pd(5wt% ) C为催化剂,采用催化加氢方法可完全脱除共聚物侧氨基上的保护基团;脱除侧氨基上的保护基团后,共聚物的分子量和Tg 值均略有增大,亲水性有所提高.     

丙交酯-乙交酯共聚中的酯交换及共聚物结构和性质研究

以辛酸亚锡为催化剂 ,通过本体开环聚合合成了不同摩尔比的DL 丙交酯 乙交酯 (DL LA GA)共聚物 (PDL LGA) .1 H和1 3C NMR以及DSC结果表明 ,共聚物中GA结构单元的含量略高于按GA投料比计算的结果 ,聚合过程中存在二级酯交换反应 .当聚合温度为 16 0℃时 , GG 序列的平均长度 (lGG)随GA摩尔投料比增大而增长 ,而 LL 序列的平均长度 (lLL)则相反 .研究发现 ,随着GA摩尔投料比降低 , LL 单元的二级酯交换系数 (TⅡ[GLG])下降 ,至GA摩尔投料比达到为 5 0 %时最小 ,而后却逐渐增大 .L LA与GA在同样的条件下聚合 ,TⅡ[GLG]和lGG 都比DL LA与GA聚合的大 .聚合温度升高 ,TⅡ[GLG]增大 ,意味着二级酯交换反应加剧 ,但DL LA GA摩尔投料比较高 (75 2 5 )的共聚物的lGG 值有所下降 ,lLL值变化不大 ,而DL LA GA摩尔投料比较低 (5 0 5 0 )的共聚物的lGG值则变化不大 ,lLL值有所下降 ,说明聚合反应还受共聚单体的投料比和其它因素影响 .升高聚合温度比在较低温度下延长反应时间更有效改变共聚物的链结构 .在一定温度下聚合 ,共聚产物的Tg 随GA摩尔投料比增大而有规律降低和在氯仿中的溶解性下降 ;而DL LA GA摩尔投料比一定时 ,聚合温度对共聚物的Tg 的影响较为复杂 ,这与聚合温度对共聚物的链结构影响较大有关 .     

L-丙交酯-β-苹果酸共聚物的体外降解及细胞亲和性研究

研究了具有功能侧基的新型生物降解高分子——— [聚 (L 丙交酯 co β 苹果酸 ) ](PLMA)在pH 7 4的磷酸缓冲溶液中的降解和鼠的 3T3成纤维细胞在共聚物膜表面的贴附及生长 .研究了不同组成的共聚物在降解过程中的失重、表面形貌、组成及分子量变化 ,发现PLMA为本体降解 ,共聚物中苹果酸含量的提高可以加速降解 ,降解过程中聚苹果酸 (PMA)链段附近的酯键先水解断裂 .鼠的 3T3成纤维细胞在聚L 丙交酯 (PLLA)均聚物和苹果酸含量为 4mol% ,8mol%和 13mol%的共聚物膜上培养 5h ,细胞贴附率分别为 4 3%、71%、80 %和 4 3% .3T3成纤维细胞在苹果酸含量为 4mol%和 8mol%的共聚物膜上的生长情况好于在PLLA均聚物和苹果酸含量为 13mol%含量的共聚物膜上的生长 .     

乙交酯、L-丙交酯均聚物及其共聚物的制备和性能研究

以辛酸亚锡为催化剂、1,4-丁二醇为引发剂,在高温、高真空条件下本体熔融开环聚合制备了聚乙交酯(PGA)、聚L-丙交酯(PLLA)及其不同比例的共聚物(PLGA).通过红外光谱(IR)、核磁共振(1H-NMR)对聚合物的结构进行了表征,用乌氏黏度计、凝胶渗透色谱仪(GPC)、示差扫描量热仪(DSC)、热重分析仪(TGA)、X射线粉末衍射仪(XRD)、流变仪等对聚合物的特性黏数、分子量与分子量分布、热性能、结晶性、流变性能进行了研究.结果表明PLGA和PLLA具有较高的分子量和窄的分子量分布;PGA、PLLA、PLGA均具有较高的热稳定性,随着PLGA中PGA单元的增加,分解温度逐渐升高.直接熔融合成的PGA在各有机溶剂中溶解性都不理想,用二甲基亚砜(DMSO)重结晶后的PGA在六氟异丙醇(HFIP)中的溶解度增大;PGA、PLLA具有较高的结晶度,而PLGA以非晶态存在,DMSO重结晶后的PGA的结晶度降低.PGA、PLLA、PLGA的熔体均是剪切变稀流体,但PGA、PLLA具有较高的储能模量,PLGA具有较高的损耗模量.相对于PGA和PLLA,无规共聚的PLGA易纯化,并且柔性较好,更易加工,因此PLGA是更适宜的生物可降解材料.     

聚乙二醇-b-聚(D,L-丙交酯-co-碳酸丙二酯)的胶束化及其药物控释研究

通过开环共聚合成了由D,L-丙交酯、碳酸丙二酯和聚乙二醇构成的两亲性嵌段共聚物(PETLA),研究了PETLA胶束化及药物控释行为.嵌段共聚物和胶束通过核磁共振(1H-NMR)、荧光分光光度计、凝胶渗透色谱(GPC)、动态光散射(DLS)、透射电镜(TEM)和紫外光谱(UV)表征.实验结果发现临界胶束浓度随共聚物疏水链段长度增加而减小,胶束直径随疏水链段长度增加而增大.透射电镜照片表明载药胶束MT1直径为30~40nm,呈规则球形.体外释药表明9-NC以可控方式释放,突释后药物释放速率接近零级恒速.     

表面接枝嵌段共聚物刷实现内皮细胞的选择性黏附

利用表面引发原子转移自由基聚合(SI-ATRP)技术将聚(甲基丙烯酸寡聚乙二醇酯)和聚(甲基丙烯酸缩水甘油酯)的双嵌段共聚物刷(POEGMA-b-PGMA)接枝在材料表面,并通过PGMA中丰富的环氧基团开环固定可特异性黏附内皮细胞的多肽GREDVY.静态水接触角、接枝层厚度、X射线光电子能谱(XPS)以及原子力显微镜(AFM)的测试结果证明了各步接枝反应的成功性.细胞培养研究表明这种连接有GREDVY的双嵌段共聚物表面能够有效的促进血管内皮细胞的黏附,同时排斥成纤维细胞的黏附,从而实现了内皮细胞的选择性黏附.     

聚(碳酸酯-co-磷酸酯)的酶促合成及性能

以猪胰脂肪酶或假丝酵母皱褶酶为催化剂, 100℃下通过本体聚合成功地合成了三亚甲基碳酸酯(TMC)和2-乙氧基-2-氧-1,3-二氧磷杂环戊烷(EEP)的无规共聚物(poly(TMC-co-EEP)). 研究了酶浓度, 聚合反应时间以及共聚单体投料比等因素对共聚物分子量和产率的影响. 随着酶(PPL或CL)浓度的增加, 共聚物分子量降低. 同时, 随着EEP投料比的增加, 共聚物的分子量也降低. 共聚物数均分子量最大可达到10200. 随着共聚单体投料摩尔比(EEP/TMC)从0增加到5︰10, 共聚物的玻璃化温度从-28℃降低到-41.7℃. 体外降解实验表明: 共聚物中磷酸酯含量越高, 降解速率越快.     

聚(L-丙交酯)/聚(DL-丙交酯)的结晶性能及相溶性

用共溶液沉淀法制备了聚 (L 丙交酯 ) 聚 (DL 丙交酯 )共混物 (PLLA PDLLA) ,然后用成纤模压法压制成3 2mm的棒材 .用差示扫描量热法研究了共混物的结晶性能和相溶性 .结果表明 ,PLLA组分在共溶液沉淀过程中可生成结晶 ,共混物中PDLLA含量直到 30 %时 ,PLLA组分的结晶熔融温度和结晶度与纯PLLA相同 ,但PDLLA含量为 5 0 %时 ,PLLA组分的结晶熔融温度和结晶度明显下降 .由于加工成型条件的不一致性 ,共混物棒材中的PLLA组分的结晶熔融温度和结晶度呈较大的分散性 .共混物从熔体降温 ,在其后的升温DSC扫描中出现分别相应于PDLLA和PLLA的玻璃化转变 ,表明PDLLA与未结晶的PLLA形成的非晶相是不相溶的     

溶解沉淀后进样-气相色谱法测定缓释制剂载体丙交酯乙交酯共聚物中单体的残留量北大核心CSCD

为了降低丙交酯乙交酯共聚物(PLGA)对单体残留量测定结果的影响,以二氯甲烷为溶剂,正己烷为沉淀剂,进行了题示项目的研究.取样品约0.1 g,加7 mL二氯甲烷(溶剂)溶解后,置于10 mL容量瓶中,加正己烷(沉淀剂)稀释至刻度.摇匀并离心后,取上清液作为供试品溶液.以Agilent HP-INNOWax毛细管色谱柱进行分离,氢火焰离子化检测器(FID)进行检测,采用气相色谱法测定上述溶液中乙交酯和丙交酯两种单体的含量.结果表明,采用溶解沉淀法,有效降低直接进样法所带来的系统污染,也大幅提高了检测准确度.两种单体的质量浓度在0.005~0.060 g·L^(-1)内均与对应的峰面积呈线性关系,乙交酯和丙交酯的检出限(3S/N)分别为2.0,1.0 mg·L^(-1),加标回收率分别为97.0%,101%.对混合对照品溶液和供试品溶液进行精密度试验,测定值的相对标准偏差(n=6)均小于3.0%.方法用于分析3批样品,两种单体残留量均小于0.050%.     

聚对苯二甲酸丁二酯/聚对苯二甲酸乙二酯固态缩聚的研究

研究了聚对苯二甲酸丁二酯(PBT)/聚对苯二甲酸乙二酯(PET)共混物的固态缩聚反应,从反应动力学过程的测定结果,表明与纯PET或PBT不同,其反应速度较快,并呈超加和的相对分子质量(以特性粘数[η]表征)增长。从反应发生在液相的基本观点出发,说明温度、共混等使液相增多,将加速反应的进行,加上共混物之间的相互缩聚和酯交换,生成嵌段共聚物的结果,导致超加和效应。     

Thermal,crystallization, mechanical,and rheological characteristics of poly(trimethylene terephthalate)/poly(ethylene terephthalate) blends

Blends of poly(trimethylene terephthalate) (PTT) and poly(ethylene terephthalate) in the amorphous state were miscible in all of the blend compositions studied, as evidenced by a single, composition‐dependent glass‐transition temperature observed for each blend composition. The variation in the glass‐transition temperature with the blend composition was well predicted by the Gordon–Taylor equation, with the fitting parameter being 0.91. The cold‐crystallization (peak) temperature decreased with an increasing PTT content, whereas the melt‐crystallization (peak) temperature decreased with an increasing amount of the minor component. The subsequent melting behavior after both cold and melt crystallizations exhibited melting point depression behavior in which the observed melting temperatures decreased with an increasing amount of the minor component of the blends. During crystallization, the pure components crystallized simultaneously just to form their own crystals. The blend having 50 wt % of PTT showed the lowest apparent degree of crystallinity and the lowest tensile‐strength values. The steady shear viscosity values for the pure components and the blends decreased slightly with an increasing shear rate (within the shear rate range of 0.25–25 s^?1); those of the blends were lower than those of the pure components. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 676–686, 2004     

New family of highly emissive,soluble poly(1,4‐fluorenylenevinylene) derivatives: Synthesis and characterization

A new poly(arylene vinylene) derivative, poly(1,4‐fluorenylenevinylene), with the advantages of poly(p‐phenylene vinylene) and polyfluorene (PF), was designed, synthesized, and characterized. The polymer showed a defect‐free structure and a number‐average molecular weight of 32,600. The resulting polymer was thermally stable with a high glass‐transition temperature (200 °C) and was readily soluble in common organic solvents. The polymer film showed a maximum emission at 515 nm and had a photoluminescence quantum yield of 58 ± 5%. A cyclic voltammetry study revealed that the highest occupied molecular orbital and lowest unoccupied molecular orbital energy levels of the polymer were 2.9 and 5.51 eV, respectively. The double‐layer light‐emitting‐diode devices fabricated from the polymer emitted bright green light with a maximum around 515 nm. The device showed a maximum luminous efficiency of 0.13 cd/A and a maximum luminance value of 600 cd/m² at 17 V. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 6515–6523, 2005     

New Approach to Determine the Phase Transition Temperature,Cloud Point,of Thermoresponsive Polymers

In this study, a novel method to determine the cloud point temperature variation in aqueous solutions of thermoresponsive homo- and copolymers was developed. Poly(N-vinylcaprolactam) (PVCL) and triblock copolymers of poly(t-butyl acrylate-co-acrylic acid)-b-poly(N-vinylcaprolactam)-b-(t-butyl acrylate-co-acrylic acid) (P[(tBA-co-AA)-b-PVCL-b-P(tBA-co-AA)] were synthesized by reversible addition-fragmentation chain transfer (RAFT) polymerization and used as models. The incorporation of AA units (hydrophilic segments) into the polymeric chain of PVCL influenced the phase transition, increasing the cloud point temperature of the final copolymer. The cloud point temperatures of the PVCL and the triblock copolymer P(tBA-co-AA)-b-PVCL-b-P(tBA-co-AA) were determined by measuring the transmittance of aqueous solutions of the polymers in a Turbiscan Lab instrument in the range of 29 to 40 C. This is the first study in which Turbiscan Lab is used to determine the cloud point temperature.     

Porous,bicontinuous, and cationic polyelectrolyte obtained by high internal phase emulsion polymerization

In this work, a cationic polyelectrolyte was synthesized through oil‐in‐water high internal phase emulsion polymerization. The porous polymer was obtained using the monomer (4‐vinyl benzyl)trimethylammonium chloride and cross‐linked with N,N‐methylene‐bis‐acrylamide; additionally, ethylene glycol dimethacrylate (EGDMA) was used as the second cross‐linker, which was solubilized in the discontinuous phase leading to a bicontinuous‐like HIPE system because of the characteristics of this cross‐linker and the phase, where polymerized several effects on the polyHIPE were expected. In this way, the effect of the emulsifier and EGDMA content on the pore size, swelling, and rheological properties was assessed. It was observed that an increased concentration of the emulsifier in the polymerization decreased the pore size, narrowed its size distribution, and diminished the swelling capacity of the polymer. Additionally, the poly (HIPE) displayed a close‐cell structure explained by the locus of initiation starting from the droplets of the emulsion. After the addition of EGDMA, the polymer exhibited a major decrease in pore size and a significant decrease in swelling attributed to the polymerized skin layer on the droplet and hydrophobicity provided by the polyEGDMA, respectively. Rheological assays revealed an increase in the complex modulus and shear stress as the pore size decreased, but the addition of EGDMA did not produce an increase in the modulus, as expected. Finally, the sorption capabilities of the cationic porous polymers were evaluated through kinetic and isotherm sorption experiments using the anionic dye Acid Black 24.     

Thermal decomposition mechanisms common to polyurethane,epoxy, poly(diallyl phthalate), polycarbonate and poly(phenylene sulfide)

Thermal decomposition of polyurethane, epoxy, poly(diallyl phthalate), polycarbonate, and poly(phenylene sulfide) was examined using a combination of thermal and chemical analysis techniques. Thermal gravimetric analysis with simultaneous analysis of evolved gases by Fourier transform infrared spectroscopy, differential scanning calorimetry, and gas chromatography coupled with Fourier transform infrared spectroscopy were used to obtain rate data, determine enthalpy changes, and identify decomposition products. Examination of the evolved decomposition products indicated a common set of chain scission mechanisms involving the aromatic moieties in each of the polymer materials studied.     

Immiscibility,upper critical solution temperature,and miscibility in blends of poly(vinyl ether)s with polyacrylics: Effects of pendant groups

Various phase behavior of blends of poly(vinyl ether)s with homologous acrylic polymers (polymethacrylates or polyacrylates) were examined using differential scanning calorimetry, optical microscopy (OM), and Fourier‐transformed infrared spectroscopy. Effects of varying the pendant groups of either of constituent polymers on the phase behavior of the blends were analyzed. A series of interestingly different phase behavior in the blends has been revealed in that as the pendant group in the acrylic polymer series gets longer, polymethacrylate/poly(vinyl methyl ether) (PVME) blends exhibit immiscibility, upper critical solution temperature (UCST), and miscibility, respectively. This study found that the true phase behavior of poly(propyl methacrylate)/PVME [and poly(isopropyl methacrylate)/PVME)] blend systems, though immiscible at ambient, actually displayed a rare UCST upon heating to higher temperatures. Similarly, as the methyl pendant group in PVE is lengthened to ethyl (i.e., PVME replaced by PVEE), phase behavior of its blends with series of polymethacrylates or polyacrylates changes correspondingly. Analyses and quantitative comparisons on four series of blends of PVE/acrylic polymer were performed to thoroughly understand the effects of pendant groups in either polyethers (PVE's) or acrylic polymers on the phase behavior of the blends of these two constituents. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1521–1534, 2007     

New polymer syntheses. CIX. Biodegradable,alternating copolyesters of terephthalic acid,aliphatic dicarboxylic acids,and alkane diols

Copolyesters with an alternating sequence of terephthalic acid and aliphatic dicarboxylic acids were prepared with three different methods. First, dicarboxylic acid dichlorides were reacted with bis(2‐hydroxyethyl)terephthalate (BHET) in refluxing 1,2‐dichlorobenzene. Second, the same monomers were polycondensed at 0–20 °C in the presence of pyridine. Third, dicarboxylic acid dichlorides and silylated BHET were polycondensed in bulk. Only this third method gave satisfactory molecular weights. Matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry revealed that the copolyesters prepared by the pyridine and silyl methods might have contained considerable fractions of cyclic oligoesters and polyesters despite the absence of transesterification and backbiting processes. The alternating sequences and thermal properties were characterized with ¹H NMR spectroscopy and differential scanning calorimetry measurements, respectively. In agreement with the alternating sequence, all copolyesters proved to be crystalline, but the crystallization was extremely slow [slower than that of poly(ethylene terephthalate)]. A second series of alternating copolyesters was prepared by the polycondensation of silylated bis(4‐hydroxybut‐ yl)terephthalate with various aliphatic dicarboxylic acid dichlorides. The resulting copolyesters showed significantly higher rates of crystallization, and the melting temperatures were higher than those of the BHET‐based copolyesters. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3371–3382, 2001     

Poly (caprolactone)/poly (ethylene glycol) pervaporation blend membranes: Synthesis,characterization, and performance

Poly (caprolactone) membranes with addition of different poly (ethylene glycol) concentrations were prepared for separation of water/isopropanol azeotropic mixture by pervaporation process. Different characterization tests including Fourier transform infrared, scanning electron microscopy, water contact angle, and thermogravimetric analysis were carried out on the prepared membranes. In addition, the effect of poly (ethylene glycol) PEG content on the swelling degree and the performance of the prepared membranes in pervaporation process were investigated. According to the obtained results, all the membranes were water selective and the blend membrane containing 3 wt% PEG exhibited the best pervaporation performance with a water flux of 0.517 kg/m² hour and separation factor of 1642 at the ambient temperature. Hydrophilicity improvement of the blend membranes was confirmed by constant decrease in water contact angle of the membranes as PEG content increased in the casting solution. Scanning electron microscopy cross‐sectional images indicated that the blend membranes containing PEG had a closed cellular structure. Furthermore, mechanical and thermal properties of the membranes decreased by adding PEG.     

Synthesis,thermal characterization,and tensile properties of alipharomatic polyesters derived from 1,3‐propanediol and terephthalic,isophthalic, and 2,6‐naphthalenedicarboxylic acid

In this work, three alipharomatic polyesters—poly(propylene terephthalate) (PPT), poly(propylene isophthalate) (PPI), and poly(propylene naphthalate) (PPN)—were prepared and studied with the aliphatic diol 1,3‐propanediol and the corresponding aromatic diacids. Their synthesis was performed by the two‐stage melt polycondensation method in a glass batch reactor. The thermal characterization of these polyesters was carried out with different thermal techniques such as simultaneous thermogravimetry/differential thermal analysis, thermomechanical analysis (TMA), and dynamic thermomechanical analysis. From the recorded values for the glass‐transition temperature (T_g) and melting temperature with all the aforementioned techniques, it could be said that they were in good agreement. According to the thermogravimetric results, PPT and PPI showed about the same thermal stability, whereas PPN seemed to be somewhere more thermostable. Remarkably, a transition existed immediately after T_g that was realized by the first derivative of TMA, and it was characterized as a midrange transition. For all polyesters, the average coefficient of linear thermal expansion was calculated with TMA. The secondary relaxations T_β and T_γ, recorded with dynamic mechanical thermal analysis, were mainly affected by the kinds of monomers. Concerning the mechanical properties, PPN had the highest tensile strength at break, whereas PPT had the highest elongation at break. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3998–4011, 2005     

Telechelic,Antimicrobial Hydrophilic Polycations with Two Modes of Action

Telechelic antimicrobial poly(2‐oxazoline)s with quaternary ammonium (quat) end groups are shown to be potent antimicrobial polymers against Gram‐positive bacterial strains. In this study, the activity against the Gram‐negative bacterium Escherichia coli is additionally implemented by hydrolyzing the poly(2‐methyl‐2‐oxazoline) with two quart end groups to poly(ethylene imine) (PEI). The resulting telechelic polycations are active against Staphylococcus aureus and E. coli. The contribution of the PEI backbone is determined by measuring the antimicrobial activity in the presence of calcium ions. The influence of PEI on the overall activity strongly depends on the molecular weight and increases with higher mass. The PEI dominates the activity against E. coli at lower masses than against S. aureus. The quart end groups require an alkyl substituent of dodecyl or longer to dominate the antimicrobial activity. Additionally, PEI and quart end groups act synergistically.