首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 46 毫秒
1.
研究了几种AB5非化学计量贮氢合金的电化学性能 ,及在低电流密度与高电流密度放电下取代元素对放电比容量、活化性能及循环寿命的影响。Sn ,Co,Mn的加入有利于提高合金的电化学贮氢容量 ,La(NiSn) 5.14 ,La(NiSnCo) 5.12 和La(NiSnMn) 5.12 具有相同的电化学贮氢容量与活化特性。尽管La(NiSn) 5.14 大电流放电性能优于La(NiSnCo) 5.12 和La(NiSnMn) 5.12 ,但其寿命短。Mn ,Co和Al可大大提高合金的使用寿命。La(NiSnCo) 5.12 被认为是一种理想的贮氢合金。  相似文献   

2.
为了获得既具有较高电化学容量又具有良好循环稳定性的低钴AB5型贮氢合金,研究了Fe部分替代Cu对低钴AB5型贮氢合金相结构和电化学性能的影响.采用真空感应熔炼方法,制备了一系列含Cu和Fe的低钴AB5型贮氢合金LaNi3.55Mn0.35Co0.20Al0.20Cu0.85-xFex(x=0.10,0.20,0.25,0.40,0.60).粉末X射线衍射(XRD)分析表明,合金含有单一CaCu5型六方结构的LaNi5相,Fe部分替代Cu并没有改变合金的本体相结构,但随着Fe含量的增大,晶格参数a,c和晶胞体积V增大.电化学性能测试表明,随着x增加,合金的放电容量和高倍率放电能力降低,但是循环稳定性得到了显著提高.当x从0.10增加到0.60时,合金的200周循环稳定性(S200)从77.6%提高到89.9%.Fe替代Cu有利于提高合金的循环稳定性,这主要是随着Fe替代量增大,晶胞体积增大,晶格体积膨胀率明显减小,合金的抗粉化能力增强.  相似文献   

3.
含锡AB5型非化学计量贮氢合金Ⅱ.电化学性能   总被引:3,自引:3,他引:0  
研究了几种AB5非化学计量贮氢合金的电化学性能,及在低电流密度与电高流密度放电下了代元素对放电比容量、活化性能及循环寿命的影响。Sn,Co,Mn的加入有利于提高合金的电化学氢容量,La(NiSn)5.14,La(NiSnCo)5.12和(NiSnMn)5.12具有相同的电化学贮氢容量与活性特性。尽管La(NiSn)5.14大电流电性能优于La(NiSnCo)5.12和La(NiSnMn)5.12,  相似文献   

4.
研究了用B掺杂替代Al对AB5型稀土贮氢合金相结构和电化学性能的影响。对M1Ni3.55Co0.75Mn0.4Al0.3-xBx(x=0,0.1,0.2,0.3)合金的研究结果表明:掺B后贮氢合金出现了CeCo4B第二相,导致贮氢合金的电化学容量下降;随B含量的增加和Al含量的减少,氢的扩散系数明显上升,合金的极化电阻减小,合金的高倍率放电性能和低温性能得到明显改善。  相似文献   

5.
研究了用B掺杂替代A1对AB5型稀土贮氢合金相结构和电化学性能的影响.对M1Ni3.55Co0.75Mn0.4Al0.3-xBx(x=0,0.1,0.2,0.3)合金的研究结果表明:掺B后贮氢合金出现了CeCo4B第二相,导致贮氢合金的电化学容量下降;随B含量的增加和A1含量的减少,氢的扩散系数明显上升,合金的极化电阻减小,合金的高倍率放电性能和低温性能得到明显改善.  相似文献   

6.
提高AB5型贮氢电极合金低温电化学性能研究   总被引:2,自引:0,他引:2  
叶辉  吴铸  李志林  张宏 《电化学》2002,8(4):460-462
采用优化稀土成分并添加适量的硼改善AB5型贮氢合金的低温性能。实验表明,含富Ce稀土及添加适量硼的AB5型合金,其低温电化学性能优良,能满足Ni/MH电池在低至-35℃小倍率电流密度放电的要求,贮氢合金低温性能的改善与合金的微结构、热力学和动力学性能相一致。  相似文献   

7.
本文对镍氢动力电池用AB5型纳米晶贮氢合金热处理工艺进行了研究.分别采用X射线衍射、金相、PCI测试手段分析热处理后贮氢合金的微观结构与吸放氢动力学性能.贮氢合金的电性能测试结果表明,经过950℃×6 h热处理的贮氢合金,10C放电比容量可以达到241mAh/g,循环寿命大于500次,分别以7C,10C放电,高倍率放电率(HRD)为92.5%,85.2%.将贮氢合金粉组装成电池进行测试,2min后,放电平台电压为1.143V,以10C放电,300次循环后,电池容量衰减率较小.  相似文献   

8.
本文较为详细地介绍了研究稀土贮氢合金性能过程中几种常用的测试技术.在贮氢合金组织结构方面,应用XRD、SEM和金相测试技术,研究贮氢合金的相结构,通过有关公式计算合金晶粒尺寸,以及反映热处理工艺前后相结构、晶粒形貌、晶界的变化情况.在贮氢合金吸放氢机理方面,通过将贮氢合金粉制作成微电极,采用恒电位阶跃、交流阻抗、循环伏安电化学测试技术,研究稀土贮氢合金电极反应的动力学性能,计算合金电极的交换电流密度、氢扩散系数及固/液界面电荷传递电阻等参数;采用PCT测试仪,研究贮氢合金的储氢量、平衡氢压等性能.在贮氢合金电化学性能方面,通过采用模拟电池测试技术,研究贮氢合金的活化、放电容量、放电平台、循环等性能.  相似文献   

9.
本文较为详细地介绍了研究稀土贮氢合金性能过程中几种常用的测试技术。在贮氢合金组织结构方面,应用XRD、SEM和金相测试技术,研究贮氢合金的相结构,通过有关公式计算合金晶粒尺寸,以及反映热处理工艺前后相结构、晶粒形貌、晶界的变化情况。在贮氢合金吸放氢机理方面,通过将贮氢合金粉制作成微电极,采用恒电位阶跃、交流阻抗、循环伏安电化学测试技术,研究稀土贮氢合金电极反应的动力学性能,计算合金电极的交换电流密度、氢扩散系数及固/液界面电荷传递电阻等参数;采用PCT测试仪,研究贮氢合金的储氢量、平衡氢压等性能。在贮氢合金电化学性能方面,通过采用模拟电池测试技术,研究贮氢合金的活化、放电容量、放电平台、循环等性能。  相似文献   

10.
添加元素对AB2型Laves相合金电化学性能的影响   总被引:3,自引:0,他引:3  
比较系统地研究了AB2型Laves相合金Zr0.9Ti0.1Ni0.1Mn0.7V0.3M0.1(M=None,Ni.Mn.V.Co.Cr.Al.Fe,Mo.Si.C.Zn,Cu和B)的相结构和电化学性能以及高温和低温放电性能等.结果表明.14种合金均具有六方C14型Laves相的主相晶体结构.同时,含有少量立方Cl5型Laves相和一些由Zr9Ni11及ZrNi组成的非Laves相;添加V和Mn可提高AB2合金的放电容量;添加B和Mn则显著提高了AB2合金的高倍率放电性能和低温放电容量;添加Al,C.Si和Co对合金电极的循环稳定性改善明显;而Mn.Ni.V.Fe.Cu.Mo和B等却不同程度地降低了循环稳定性;添加Si.Mo,V,Cr和Al可明显改善合金电极的自放电性能;添加Si.Cr.V可显著改善AB2合金电极的高温放电性能.讨论了各种添加元素影响合金性能的可能原因.  相似文献   

11.
随着信息技术的高速发展和大数据时代的到来,有效存储和管理海量数据的要求对数据存储技术提出了严峻挑战。光存储技术在能耗、容量、成本、寿命、安全等方面的优势,使其正逐渐成为未来数据存储的主流技术。本文围绕光存储技术的维度展开论述,纵向介绍了几种常用的光存储技术。目前以光盘为代表的二维面存储技术,存储容量已接近其理论存储极限(23.5 GB/disc);以双光子吸收技术、全息存储技术为代表的三维体存储技术,其存储容量相较二维存储技术提升了2~4个数量级;五维存储技术进一步扩展了数据存储的维度。可以预见,未来光存储技术会在大存储容量、超高存取速度、高性能存储材料、多维度存储技术等方面取得突破和进展。  相似文献   

12.
An overview of the importance of and methods available for heat storage in the form of sensible and latent heat is followed by a discussion of the advantages and disadvantages of reversible thermochemical energy storage compared to conventional energy sources such as fuels, i.e. irreversible chemical energy carriers. Of the reversible metal-hydride–metal systems, the MgH2? Mg system is particularly attractive as a hydrogen and a high-temperature heat storage material because of its high hydrogen content and the high energy content of the Mg–H bond. The advances made in this area over the past few years, namely in catalytic hydrogenation and the doping of magnesium powders, have led to the development of “active MgH2? Mg systems” for energy storage. The first experimental results on high-temperature heat storage (also with cooling) by coupling a MgH2? Mg storage system with a low-temperature metal hydride storage system are presented.  相似文献   

13.
光子存储原理与光致变色材料   总被引:14,自引:0,他引:14  
樊美公 《化学进展》1997,9(2):170-178
光子存储是信息科学中的一个前沿课题。本文主要包括以下内容: 光子存储的4种方式; 光子烧孔、电子捕获、光折变和光致变色存储的原理和材料; 双光子三维光存储原理和材料; 可能的发展方向。  相似文献   

14.
贮氢材料及其应用研究进展   总被引:1,自引:0,他引:1  
贮氢材料是一类新型高性能材料。本文对现有贮氢材料进行了合理的分类,对贮氢材料及其应用研究进展进行了综述。  相似文献   

15.
The utilization of simple photochemical reactions for the storage of solar energy in the form of chemical energy in energy-rich products has often been considered in the further development and improvement of e. g. simple thermosolar techniques. The hitherto proposed criteria for the qualification of an abiotic photochemical system are, however, mostly of a qualitative nature, so a mutal comparison of the systems is not precise enough. In this article it is shown how a useful correlation on the basis of time-independent experimental data can be achieved and how, from the viewpoint of photochemistry, a comparative classification of known reactions is possible. The following reactions are compared: the [2 + 2]-photocycloadditions of norbornadiene, dimethyl 2,3-norbornadienedicarboxylate, and dicyclopentadienone, the photoisomerization of trans- to cis-diacetylindigo, the photodissociation of nitrosyl chloride as well as a photocatalytic redox reaction. The quantity of material required and storage efficiency are by far the most favorable in the case of trans-diacetylindigo. The main disadvantage of the latter however, is that the energy-rich cis-from rapidly reverts to the stable trans-form at elevated temperatures.  相似文献   

16.
在贮氢合金MmNi3.8Co0.5Mn0.4Al0.3(Mm为混合希土)粉末表面分别进行化学镀Cu,Co,Ni,Ni-Co,Ni-Sn,Ni-W。结果表明不同化学镀对合金贮氢性能有很大影响。  相似文献   

17.
当今社会,电化学储能器件在人类的社会活动中变得越来越重要。电极材料作为电化学储能器件的核心部分,一直是人们研究的焦点。石墨炔是一种新型的二维平面结构的全碳材料,它宽的层间距、大的比表面积、独特的三维孔隙结构和好的导电性使其在能源存储器件电极材料应用中具有巨大的潜力。基于石墨炔温和的制备方法与独特的结构特征,本文详细介绍了近年来石墨炔在储能方面的理论分析和实验进展。通过研究锂/钠在单层、多层石墨炔上的迁移率和存储,理论分析石墨炔基电池具有很好的储锂储钠性能。实验方面,石墨炔作为电极材料在储钠储锂方面的容量与理论值相近。此外石墨炔作为电极材料成功应用于超级电容器和金属-硫电池,并表现出了优异的容量存储性能。石墨炔纳米形貌的调控、石墨炔的热处理,以及异原子的掺杂等均可以有效地提高石墨炔在这些储能器件中的性能。  相似文献   

18.
混合高级醇固-液相变储热材料的研究   总被引:1,自引:0,他引:1  
相变储热材料研究与开发是国内外的一个新兴领域[1-6]。为了解决一些仪器的内部散热问题,本文研究了混合高级醇固-液相变储热材料的凝固和熔化特性、相变焓值、固液相体积以及石墨粉对材料的导热性能。1实验部分1·1试剂与仪器CDR-1型差动热分析仪-配微机处理系统,上海天平仪器  相似文献   

19.
The outstanding feature of materials research in the eighties has been the convergence of basic research and practical application, leading to ever shorter cycles of innovation. This is especially true of materials which form the basis of key technologies. The mass storage units of the next generations of computers will be based on optical processes having a storage density which exceeds that of all hitherto known storage techniques that are practicable from the technical standpoint. In view of the fact that since 1982 read-only memories in the form of compact discs (CD-ROM) have become very successful in the field of audio electronics, research and development are now concentrated on materials for write-once (WORM) and erasable (EDRAW) storage systems. Suitable materials for optical data storage are substances in which data markings can be recorded and deleted respectively using semiconductor lasers. Materials development is centered on the synthesis of infrared-absorbing dyes for WORM memories and the production of rare earth/transition metal alloys for magneto-optical data recording. An introduction to CD-ROM technology will be followed by an overview of the state of development of the most important storage materials which are currently available commercially, and then the properties of these materials will be discussed with reference to selected examples.  相似文献   

20.
Hierarchical hollow CoP and carbon composites were obtained through a facile synthetic method, where carbonization and phosphorization of the precursor were completed within one single step. The composites are composed of hollow CoP@C spheres, which are further made up of CoP nanoparticles with a thin outer carbon layer. Electrochemical performances of the prepared CoP@C composites as anodes for sodium and potassium storage were evaluated and compared. In situ TEM, in situ synchrotron XRD, and DFT calculations were conducted to study the structural evolution and the interaction between Na/K and CoP during cycling processes. Benefiting from the synergistic effect of conductive carbon layer and hierarchical hollow structure, the as‐prepared CoP@C composites demonstrate superior sodium and potassium storage capability as anode materials for rechargeable batteries.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号