Participation of electrolyte cations in albumin adsorption onto negatively charged polymer latices

The participation of electrolyte cations in the adsorption of bovine serum albumin (BSA) onto polymer latices was investigated. The latices used were hydrophobic polystyrene (PS), and hydrophilic copolymers, i.e., styrene (St)/2-hydroxyethyl methacrylate(HEMA) copolymer [P(St/HEMA)] and styrene/acrylamide (AAm) copolymer [P(St/AAm)]. Three kinds of electrolyte cations (Na⁺, Ca²⁺, Mg²⁺) were used as the chloride. The amount of BSA adsorbed in every cation medium showed a maximum near the isoelectric point (iep, pH about 5) of the protein. The amounts of BSA adsorbed onto copolymer latices (except in the acidic pH region lower than the iep) were considerably smaller than that onto PS latex because of the steric repulsion and the decrease in the hydrophobic interaction between BSA and copolymer latices. In the acidic pH region, there was little difference in the amount of BSA adsorbed in every cation medium. However, in the pH region higher than the iep, the amounts of BSA adsorbed (particularly onto PS latex) in divalent cations (Ca²⁺ and Mg²⁺) media were relatively greater compared with that in a monovalent (Na⁺) one. This result was interpreted on the basis of the differences in such effects of electrolyte cations as dehydration power, suppression of the electrostatic repulsion, and binding affinity to BSA molecule. Ion Chromatographic estimation of the amounts of electrolyte cations captured upon BSA adsorption (in pH > 5) revealed that divalent cations were incorporated into the contact interface between the latex and BSA molecule so as to prevent the accumulation of anion charge and facilitate the protein adsorption.     

Electrokinetic characterization of polystyrene–non-ionic surfactant complexes

An experimental study on the electrophoretic mobility (μ_e) of polystyrene particles after the adsorption of non-ionic surfactants with different chain lengths is described. Two sulphate latexes with relatively low surface charge densities (3.2 and 4.8 μC cm⁻²) were used as solid substrate for the adsorption of four non-ionic surfactants, Triton X-100, Triton X-165, Triton X-305 and Triton X-405, each one with 9–10, 16, 30 and 40 molecules of ethylene oxide (EO), respectively. The electrophoretic mobility of the polystyrene–non-ionic surfactant complexes was studied versus the amount of adsorbed surfactant (Γ). The presence of non-ionic surfactant onto particles surface seems to produce a slight shifting of the slipping plane because the mobilities of the different complexes display a very small decreasing. The increase in the number of EO chains in the surfactant molecule seems to operate as a steric impediment which decreases the number of adsorbed large surfactant molecules. The electrophoretic mobilities of the latex–surfactant complexes with maximum adsorption were measured versus the pH and ionic strength of the dispersion. While the different complexes showed a similar qualitative behaviour compared with that of the bare latex against the pH, the adsorption of the surfactant reduces the typical maximum in the μ_e−log[electrolyte].     

Polymer mediated peptide immobilization onto amino-containing N-isopropylacrylamide-styrene core-shell particles

Monodisperse cationic core-shell latex particles have been prepared using a shot polymerization process, with N-(3-aminopropyl)-methacrylamide-hydrochloride (APMH) as the functional monomer. The final latexes were characterized with respect to final polymerization conversion, water soluble polymer formation, particle size and size distribution, surface charge density and electrokinetic properties. Then the covalent grafting of maleic anhydride-alt-methyl vinyl ether (MAMVE) copolymer onto aminated latex particles was investigated. The most efficient conditions to obtain derivatised particles with no alteration of the colloidal stability were to control both polymer amount/latex particles concentration ratio and the mixing method of the two species. The charge inversion of the hydrolysed MAMVE functionalized particles was demonstrated by measuring the electrophoretic mobility as a function of pH. Finally, the covalent binding approach was implemented with peptide-MAMVE conjugates, confirming the great potential of this promising methodology for the preparation of reactive latex particles bearing peptides.     

Hydrophilic magnetic polymer latexes. 1. Adsorption of magnetic iron oxide nanoparticles onto various cationic latexes

With a view to preparing monosized hydrophilic functional magnetic latex particles based on a two-step strategy using anionic iron oxide and cationic polymer latexes, the adsorption step was systematically investigated for a better control of the subsequent encapsulation step. The iron oxide nanoparticles were first obtained according to the classical precipitation method of ferric and ferrous chloride salt using a concentrated sodium hydroxide solution, whereas the polystyrene (PS), P(S/N-isopropylacrylamide (NIPAM)) core–shell and PNIPAM latexes were produced via emulsion and precipitation polymerizations, respectively. The polymer and inorganic colloids were then characterised. The adsorption of iron oxide nanoparticles onto the three types of polymer latexes via electrostatic interaction was studied as a function of iron oxide particle concentration, charge density and the cross-linking density of the hydrophilic layer. The maximum amounts of magnetic nanoparticles adsorbed onto the various latexes were found to increase in the following order: PS < P(S/NIPAM) < P(NIPAM). This significant difference is discussed by taking into account the charge distribution in the hydrogel layer and diffusion phenomena inside the cross-linked hydrophilic shell. Received: 28 December 1998 Accepted in revised form: 15 April 1999     

CONCERNING THE ORIGIN OF CHARGE AT THE POLYSTYRENE PARTICLE/WATER INTERFACE

The electrophoretic mobility behavior of well-characterized polystyrene latex particles, carrying one type of surface functional endgroups, has been studied as a function of pH. At low pH, the interaction of protons with the functional endgroups increased in the order: Hydroxyl > carboxyl > sulfate; at high pH the order of interaction was reversed; and at intermediate pH no interactions were observed. The particles of the polystyrene latexes in their different forms at the intermediate pH range, dispersed in deionized water, all exhibited the same mobility irrespective of the functional endgroup. The origin of charge in these systems is explained as being the result of either the preferential adsorption of hydroxyl ions or an electron - injection mechanism due to the overlap of local intrinsic molecular - ion states in polystyrene and water. At low concentrations of functional endgroups, the surface properties of the polystyrene latexes are largely dependent upon the hydrophobic nature of the surface.     

Interaction of dissolved proteins with spherical polyelectrolyte brushes

We consider the adsorption of bovine serum albumin (BSA) on spherical polyelectrolyte brushes (SPB). The SPB consist of a solid polystyrene core of 100nm diameter onto which linear polyelectrolyte chains (poly(acrylic acid), (PAA)) are grafted. The adsorption of BSA is studied at a pH of 6.1 at different concentrations of added salt and buffer (MES). We observe strong adsorption of BSA onto the SPB despite the effect that the particles as well as the dissolved BSA are charged negatively. The adsorption of BSA is strongest at low salt concentration and decreases drastically with increasing amounts of added salt. The adsorbed protein can be washed out again by raising the ionic strength. The various driving forces for the adsorption are discussed. It is demonstrated that the main driving force is located in the electrostatic interaction of the protein with the brush layer of the particles. All data show that the SPB present a new class of carrier particles whose interaction with proteins can be tuned in a well-defined manner.     

Grafting of amino functional monomer onto initiator-modified polystyrene particles

Polystyrene nanoparticles with grafted chains of an amino functionalized polymer were prepared by a two-step polymerization process. In the first step, the polystyrene seed particles were synthesized by the conventional batch emulsion polymerization using terpolymer HAS (hydroperoxide monomer, acrylic acid, and styrene) as a surface-active initiator. The surface of the obtained particles contains carboxyl groups, which are responsible for the latex stability, and residual undecomposed hydroperoxide groups. Therefore, in the second step, an amino functional monomer was grafted onto the hydroperoxide modified polystyrene particles by a "grafting from" approach. X-ray photoelectron spectroscopy, NMR, and scanning electron microscopy were used to examine the surface of the amino functionalized particles. The amount of incorporated amino groups onto the particles was determined by fluorescenometric titration. In general, the number of amino groups on the particle surface increased with the increase of the functional monomer content in the reaction mixture. The incorporation of the functional monomer was also confirmed by electrophoretic measurements. Final particles possess amphoteric character due to the presence of amino and carboxyl groups on the surface. Adsorption of human immunoglobulins G onto the amino functionalized particles was studied as a function of pH and ionic strength. The covalent binding of human IgG was performed using the glutaraldehyde preactivation method. The immunoreactivity of the latex-IgG complex was examined by the latex agglutination test.     

The adsorption of polyampholytes on negatively and positively charged polystyrene latex

The adsorption of two polyampholytes (a random copolymer of -glutamic acid and -lysine, and a well-defined tetramer of -lysyl- -glutamyl-glycine) onto positively and negatively charged latex was studied as a function of the pH and the ionic strength. The adsorbed amount proved to be almost independent of the salt concentration. The pH dependence was found to follow the same trends on negatively charged and positively charged latex. At low pH, where the polyampholytes are positively charged, a high adsorbed amount was found irrespective of the sign of the surface charge. At high pH, where the macromolecules are negatively charged, no adsorption was measured, not even with the positive latex. This is probably due to the very good solubility of the polyampholytes at this pH. Electrophoretic mobility measurements revealed that already at very low concentrations of polyampholyte charge reversal of the particles occurred.     

Film-forming microgels for pH-triggered capture and release

The pH-responsive behavior for a series of lightly cross-linked, sterically stabilized poly(tertiary amine methacrylate)-based latexes adsorbed onto mica and silica was investigated using in situ tapping mode AFM at room temperature. The adsorbed layer structure was primarily determined by the glass transition temperature, T(g), of the latex: poly[2-(diethylamino)ethyl methacrylate]-based particles coalesced to form relatively featureless uniform thin films, whereas the higher T(g) poly[2-(diisopropylamino)ethyl methacrylate] latexes retained their original particulate character. Adsorption was enhanced by using a cationic poly[2-(dimethylamino)ethyl methacrylate] steric stabilizer, rather than a nonionic poly(ethylene glycol)-based stabilizer, since the former led to stronger electrostatic binding to the oppositely charged substrate. Both types of adsorbed latexes acquired cationic microgel character and swelled appreciably at low pH, even those that had coalesced to form films. Fluorescence spectroscopy was used to study the capture of a model hydrophobic probe, pyrene, by these adsorbed latex layers followed by its subsequent release by lowering the solution pH. The repeated capture and release of pyrene through several pH cycles was also demonstrated. Since these poly(tertiary amine methacrylate) latexes are readily prepared by aqueous emulsion polymerization and adsorption occurs spontaneously from aqueous solution, this may constitute an attractive route for the surface modification of silica, mica and other oxides.     

Attachment of horseradish peroxidase (HRP) onto the poly(styrene/acrolein) latexes and onto their derivatives with amino groups on the surface; activity of immobilized enzyme

The polystyrene (P(S)), poly(styrene/acrolein) (P(SA)), and polyacrolein (P(A)) latexes, with varied fraction of polyacrolein in the surface layer (f _A=0, 0.50, 0.63, 0.84, 1.00), were used for the attachment of horseradish peroxidase. Surfaces of latexes were modified by reaction with ethylenediamine. In this step the aldehyde groups from polyacrolein were blocked and the primary amino groups were introduced. The carbohydrate portion of HRP was oxidized in the reaction leading to formation of aldehyde groups. The adsorption and covalent immobilization of HRP onto the P(S), P(SA), and P(A) latexes and of the oxidized HRP (HRP-OX) onto the modified latex particles, with amino groups on the surface (P(SA)-M and P(A)-M), were investigated. The activities of parent and oxidized HRP were compared with activities of the corresponding enzymes in solution. It has been found that whereas HRP is not suitable for the covalent immobilization on P(SA) latex and loses its activity after adsorption onto P(S) latex, HRP-OX can be adsorbed onto P(S) latex and is readily immobilized covalently onto the ethylenediamine modified P(SA) and P(A) latexes, retaining much of its former enzymatic reactivity.This work was supported by the KBN Grant 2 0624 91 01     

Mechanisms of fibrinogen adsorption on latex particles determined by zeta potential and AFM measurements

The adsorption of fibrinogen on polystyrene latex particles was studied using the concentration depletion method combined with the AFM detection of residual protein after adsorption. Measurements were carried out for a pH range of 3.5-11 and an ionic strength range of 10(-3)-0.15 M NaCl. First, the bulk physicochemical properties of fibrinogen and the latex particle suspension were characterized for this range of pH and ionic strength. The zeta potential and the number of uncompensated (electrokinetic) charges on the protein were determined from microelectrophoretic measurements. It was revealed that fibrinogen molecules exhibited amphoteric characteristics, being on average positively charged for pH <5.8 (isolectric point) and negative otherwise. However, the latex particles did not show any isoelectric point, remaining strongly negative for this pH range. Afterward, systematic measurements of the electrophoretic mobility of fibrinogen-covered latex were carried out as a function of the amount of adsorbed protein, expressed as the surface concentration. A monotonic increase in the electrophoretic mobility (zeta potential) of the latex was observed in all cases, indicating a significant adsorption of fibrinogen on latex for pH below 11. It was also proven that fibrinogen adsorption was irreversible, with the maximum surface concentration varying between 2.5 and 5 × 10(3) μm(-2) (weight concentration of a bare molecule was 1.4 to 2.8 mg m(-2)). These measurements revealed two main adsorption mechanisms of fibrinogen: (i) the unoriented (random) mechanism prevailing for lower ionic strength, where adsorbing molecules significantly penetrate the fuzzy polymeric layer on the latex core and (ii) the side-on adsorption mechanism prevailing for pH > 5.8 and a higher ionic strength of 0.15 M. It was also shown that in the latter case, variations in the zeta potential with the protein coverage could be adequately described in terms of the electrokinetic model, previously formulated for planar substrate adsorption. On the basis of these experimental data, an efficient procedure of preparing fibrinogen-covered latex particles of controlled monolayer structure and coverage was envisaged.     

Effects of oligonucleotide adsorption on the physicochemical characteristics of a nanoparticle-based model delivery system for antisense drugs

Cationic polystyrene nanoparticles, as a model drug carrier system for nucleic acids, are capable of binding negatively charged oligonucleotides by multiple electrostatic interactions. The effect of the adsorption of phosphorothioate oligonucleotides on the physicochemical properties of the carrier system was investigated for uncoated and sterically stabilized latex particles. Turbidity measurements and photon-correlation spectroscopy indicate that the colloidal stability of the nanoparticle-oligonucleotide conjugates is influenced by the number of oligonucleotides adsorbed on the carrier. Especially in the case of the uncoated material, a destabilizing effect has been observed up to oligonucleotide concentrations of 2.7 μmol/g polymer. Strikingly, at higher concentrations the latexes exhibit colloidal stability similar to the oligonucleotide-free samples. These results were correlated to zeta-potential measurements demonstrating a reversal from positive to negative values of the zeta potential with increasing oligonucleotide concentration. The points of zero charge of the particles are in the region of maximum coagulation. These findings were compared to adsorption studies and calculations based on the random sequential adsorption model. It appears that at first the colloidal stability of the carrier systems is diminished with increasing oligonucleotide adsorption, while higher surface coverages lead to a significant reduction in coagulation. At the saturation level the surface coverage can be considered as a monolayer of “side-on” adsorbed molecules and the conjugates exhibit colloidal stability similar to the bare particles without adsorbed molecules. Received: 20 April 1998 Accepted: 16 July 1998     

Charge regulation enables anionic hydroxypropyl guar-borate adsorption onto anionic and cationic polystyrene latex

Reported are adsorption isotherms for guar and hydroxypropyl guar (HPG), with and without the presence of borate ions, onto surfactant free anionic polystyrene latex. Guar and HPG formed adsorbed monolayers on the hydrophobic latex. The presence of borate ions converted the nonionic guar and HPG into an anionic polyelectrolyte. However, there was no measurable influence of bound borate ions on the adsorption of guar or HPG onto anionic, hydrophobic latex. To underscore the unusual behavior of HPG-borate, a sample of HPG was oxidized to introduce carboxyl groups, and the adsorption of the carboxylated HPG onto anionic polystyrene was measured. Unlike HPG-borate, oxidized HPG did not adsorb onto negative polystyrene latex at neutral pH because of electrostatic repulsion. To explain the adsorption of negative HPG-borate onto negative latex, we proposed that as HPG-borate segments approach the latex surface, the negative electrostatic potential near the latex surface induces the detachment of the labile borate groups from HPG.     

Adsorption of cationic polyelectrolyte onto a model carboxylic latex and the influence of adsorbed polycation on the charge regulation at the latex surface

 Adsorption of a well-characterized cationic polyacrylamide (CPAM) onto the surface of a model colloid (monodisperse polystyrene latex with carboxylic functional groups) was studied over a wide range of pH (4–9) and KCl concentration (c _s =10^-3–0.3 M). The surface charge density of the latex particles with and without adsorbed CPAM was also measured over the same range of electrolyte compositions. The adsorbed amount of CPAM increases with increase in c _s and pH. The polyelectrolyte adsorption alters substantially the surface charge density of the latex particles as compared to the polymer-free case. A large overcompensation of the surface charge by the adsorbed polyelectrolyte is established at high c _s and low pH. A qualitative explanation of the observed features is put forward. Received: 3 December 1996 Accepted: 20 January 1997     

Polymerization of styrene with ionic comonomer,nonionic comonomer,or both

Nanosized polystyrene latexes with high polymer contents were obtained from an emulsifier-free process by the polymerization of styrene with ionic comonomer, nonionic comonomer, or both. After seeding particles were generated in an initial emulsion system consisting of styrene, water, an ionic comonomer [sodium styrenesulfonate (NaSS)] or nonionic comonomer [2-hydroxyethyl methacrylate (HEMA)], and potassium persulfate, most of the styrene monomer or a mixture of styrene and HEMA was added dropwise to the polymerizing emulsion over 6 h. Stable latexes with high polystyrene contents (≤25%) were obtained. The latex particle weight-average diameters were largely reduced (41 nm) by the continuous addition of monomer(s) compared with those (117 nm) obtained by the one-pot polymerization method. Latex particles varied from about 30 to 250 nm in diameters, whereas their molar masses were within 10⁴ to 10⁵ g/mol. The effect of the comonomer concentration on the number of polystyrene particles per milliliter of latex and the weight-average molar masses of the copolymers during the polymerization are discussed. The surface compositions of the latex particles were analyzed by X-ray photoelectron spectroscopy, which indicated that the surface of the latex particles was significantly enriched in NaSS, HEMA, or both. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1634–1645, 2001     

Preparation of colored latex with polyurea shell by miniemulsion polymerization

Colored latexes with polyurea shell were prepared by applying interfacial polycondensation reaction to the miniemulsion polymerization process. These colored latexes were composed of polystyrene core and polyurea shell, and their particle size was adjusted to <100 nm. Diisocyanate was used as a hydrophobic monomer, and the equivalent mole of diamine was used as a hydrophilic monomer for interfacial polymerization. It was important to control the rate of interfacial polycondensation reaction in order to prepare small particles. Dye preservation property of colored latex loaded with oil-soluble dye was investigated. Polyurea shell formed at the surface of latex particles could restrain the migration of dyes from the latex particles and improve the dye preservation property. The ability to prevent dye migration depended on the composition of the polyurea shell.     

含二十二烷基聚氧乙烯醚甲基丙烯酸酯功能单体的缔合型乳液增稠剂的制备及表征

以甲基丙烯酸、丙烯酸乙酯、邻苯二甲酸二烯丙酯和不同量的功能单体二十二烷基聚氧乙烯醚甲基丙烯酸酯(BEM)为原料,采用半连续乳液聚合方法合成了疏水改性碱溶性缔合型增稠剂乳液.测定了增稠剂乳液的粘度、透光率、乳胶粒粒径及其分布等性能,考察了不同固含量下乳液粘度和透光率随pH的变化情况.结果表明随着BEM用量的增加,乳胶粒粒径逐渐增大.随着pH值的增加,乳液的粘度首先迅速升高,然后缓慢下降.与不含BEM的增稠剂乳液相比,当乳液固含量大于0.5%,BEM含量占单体量低于5.0wt%时,该缔合型增稠剂的增稠效果和抗剪切性有显著提高,BEM含量较高(8.0wt%或更高)时反而使增稠效果和抗剪切性变差.在此基础上研究了增稠剂对苯丙乳液的增稠效应,结果显示BEM含量占单体量的2.5wt%时,对苯丙乳液的增稠作用最好.与使用功能单体三苯乙基苯酚聚氧乙烯醚甲基丙烯酸酯改性的增稠剂相比,含BEM的增稠剂在BEM用量较少的情况下就能起到明显的增稠效果.     

BSA adsorption on differently charged polystyrene nanoparticles using isothermal titration calorimetry and the influence on cellular uptake

BSA adsorption onto negatively and positively charged polystyrene nanoparticles was investigated. The nanoparticles were characterized in terms of particle size, zeta potential, surface group density, and morphology. The adsorption behavior of BSA on the particle surface, as a function of pH and overall charge of the particle, was studied using ITC. Different thermodynamic data such as enthalpy changes upon binding and stoichiometry of the systems were determined and discussed. The degree of surface coverage with BSA was calculated using the thermodynamic data. The cellular uptake of particles before and after BSA adsorption was studied using HeLa cells in the presence and absence of supplemented FCS in the cell culture medium.     

Controlling deposition and release of polyol-stabilized latex on boronic acid-derivatized cellulose

Poly(glycerol monomethacrylate)-stabilized polystyrene (PGMA-PS) latex particles undergo specific, pH-dependent adsorption onto regenerated cellulose film bearing surface phenylboronic acid groups (cellulose-PBA). Deposition occurs at pH 10 and is driven by the boronate ester formation with the polyol latex surface coating. In contrast, no deposition occurs at pH 4, and previously deposited particles can be readily desorbed at this lower pH. In control experiments, conventional anionic sulfate-stabilized polystyrene latex did not deposit onto the hydrophilic cellulose surface. The distribution of boronate groups in the cellulose was determined by exposure to Alizarin Red S dye, which forms a fluorescent complex with phenylboronic acid; confocal microscopy was used to determine a surface density of 3 nm(2) per boronic acid group on the cellulose surface. Although the boronic acid binding constant with PGMA is relatively low (5.4 L/mol), the cooperative interactions between multiple PBA surface sites and the many PGMA chains per latex particle are sufficient to induce specific latex adsorption, providing a convenient new tool for controlling nanoparticle deposition on surfaces.