13X分子筛去除水中重金属离子的研究

以人工合成的13X型分子筛为吸附剂,研究了水中Pb2 、Cd2 和Cu2 在分子筛上的吸附行为,讨论了Pb2 、Cd2 和Cu2 共存条件下的竞争吸附,并考察了水中存在的Na 、Mg2 、Ca2 等离子对分子筛吸附去除重金属的影响.实验结果表明,13X分子筛对Pb2 、Cd2 和Cu2 3种离子的吸附符合Langmuir模型,最大吸附量分别为2.47mmol/L、2.0mmol/L和1.78mmol/L.在竞争吸附条件下,13X分子筛对3种重金属离子的选择性依次为pb2 ＞Cd2 ＞Cu2 .水中存在的Na 、Mg2 、Ca2 等对分子筛吸附重金属效率有一定的影响,其中Ca2 对Cu2 在分子筛上的去除影响最为显著.     

羧甲基二硫代氨基甲酸酯功能化聚氯乙烯树脂的合成及对Ag~+的吸附与选择性能

以聚氯乙烯为大分子骨架,经三乙烯四胺胺化,再与二硫化碳和乙醇钠反应,得到的二硫代氨基羧酸盐改性聚氯乙烯树脂(PV-NS)进一步与氯乙酸钠反应,合成了一种同时舍N,S,O的羧甲基二硫代氨基甲酸酯改性聚氯乙烯树脂(PV-NSO).合成树脂的功能基结构经红外和元素分析确认.对合成树脂的吸附性能研究表明,合成树脂对Ag+、Hg2+、Au<'3+>、Pb2+离子的吸附容量在实验条件下分别达2.058mmol/g、1.514mmol/g,1.125mmol/g和0.415mmol/g,而对Cu2+、Cd2+、Zn2+、Ni2+、Mg2+等离子的吸附容量很小,甚至不吸附.树脂的选择性吸附表明,树脂对Ag+的吸附选择性较好,在有Hg2+、Pb2+、Cd2+、Zn2+、Cu2+或Mg2+共存时,树脂对Ag+的选择性吸附系数分别达4.74、17.33,12.98、∞、7.60和74.14.合成树脂在极性溶剂中的溶胀性能均比在非极性溶剂中好.     

麦麸对重金属离子的吸附性能研究

以麦麸为天然吸附剂,从水溶液中去除重金属离子.实验表明,麦麸对重金属离子有优良的吸附性能.在约10min内达到吸附平衡,吸附容量分别为:Hg2 70mg/g、Pb2 63mg/g、Cd2 21mg/g、Cu2 15mg/g、Ni2 13mg/g及Cr3 9.3mg/g;吸附速率很快,并且对上述金属离子有良好的选择性.     

海藻酸-壳聚糖-海藻酸离子取代凝胶离子的取代性能

研究了海藻酸 壳聚糖 海藻酸 (alginate chitosan alginate ,ACA)离子取代凝胶对二价离子的取代性能。与传统离子交换树脂比较 ,ACA的离子取代速率比传统离子交换树脂快得多。ACA对二价金属离子的取代顺序是 :Pb2 + >Cu2 + >Ca2 + ≈Zn2 + ,其中 ,对Pb2 + 的选择性要大大高于Ca2 + ,其选择性系数是 316。ACA离子取代凝胶具有较快的离子取代速率和较高的吸附选择性 ,这使它有望成为一种新型的血液吸附剂用于临床金属中毒治疗。     

螯合树脂S930对Cu(Ⅱ)、Pb(Ⅱ)、Cd(Ⅱ)的吸附性能与作用机理研究

通过静态吸附和动态吸附研究系统分析了螯合树脂S930对单组分与双组分体系中Cu(Ⅱ)、Pb(Ⅱ)、Cd(Ⅱ)的吸附行为,经结构表征(FT-IR、XPS)与软硬酸碱理论(HASB)深入探讨了3种金属离子在S930树脂上的作用机理。结果表明,树脂吸附金属离子的最佳pH值为5.0左右,且对Cu(Ⅱ)、Pb(Ⅱ)的吸附过程符合Langmuir方程,而对Cd(Ⅱ)的吸附过程符合Freundlich方程。吸附过程在6h左右达到平衡,且符合Lagergren二级吸附动力学模型,表明化学作用是吸附速率决定步骤。Cu(Ⅱ)、Pb(Ⅱ)的动态吸附过程符合Thomas模型。FT-IR、XPS及HASB同时证明树脂对Cu(Ⅱ)、Pb(Ⅱ)的作用包括离子交换与配位作用,而对Cd(Ⅱ)的作用以离子交换为主,是树脂对Cd(Ⅱ)吸附选择性较差的主要原因。     

聚合物假冠醚研究(IV) 酚醛型双氮杂假冠醚聚合物的吸附特性

研究了以双氮杂假冠醚环为主体功能基的酚醛型聚合物对金属离子的吸附性能．结果表明，聚合物对K ，Hg2 ，Na ，Cd2 ，Pb2 和Cu2 离子具有良好的吸附性能，其吸附容量分别达1．79mmol／g-r，1．38mmol／g-r，0．89mmol／g-r，0．68mmol／g-r，0．63mmol／g-r和0．57mmol／g-r，对K 和Hg2 离子具有良好的吸附选择性．通过FTIR光谱法对吸附机理作了初步探讨．     

聚苯乙烯负载2-氨基-5-乙基-1,3,4-噻二唑螯合树脂的合成及其吸附性能

以氯甲基化聚苯乙烯 (PS)、一缩二乙二醇 (DEG)、二缩三乙二醇 (TEG)为原料,通过亲水性悬臂将杂环功能基2-氨基5-乙基-1,3,4-噻二唑 (AETZ) 引入到聚苯乙烯-二乙烯苯母体中,合成了两种新型螯合树脂 (PS-DEG-AETZ,PS-TEG-AETZ),并对两种树脂进行了红外光谱和元素分析表征.测定了该树脂对Cu2 、Pb2 、Zn2 、Ag 、Hg2 等金属离子的吸附性能.结果表明,PS-DEG-AETZ,PS-TEG-AETZ对Hg2 、Ag 的静态吸附量分别为0.41mmol/g和0.30mmol/g,对Cu2 、Pb2 、Zn2 的吸附量为零,表现出很好的吸附选择性,亲水性悬臂长度的增加有利于树脂吸附量的增加.     

聚丙烯酸盐-丙烯酰胺水凝胶的制备及对重金属离子吸附性能的研究

以丙烯酸(AA)、丙烯酰胺(AM)为单体,K2S2O8为引发剂,N,N'-亚甲基双丙烯酰胺为交联剂,采用水溶液聚合法合成P(AA-AM)水凝胶,通过正交实验优化了P(AA-AM)水凝胶的制备工艺.对制备的P (AA-AM)水凝胶进行了SEM和XPS分析,探讨了P(AA-AM)水凝胶对Cu2+、pb2+、Zn2+和Cd2+的吸附等温线和吸附动力学行为,研究了P(AA-AM)水凝胶的粒径、吸附温度、pH值和重金属离子的初始浓度对P(AA-AM)水凝胶吸附性能的影响.实验结果表明,所制备的P(AA-AM)水凝胶是一种具有三维网络结构的高分子材料,其表面的氨基和羧基残基能够与重金属离子发生螯合反应.减小P(AA-AM)水凝胶粒径、增大溶液pH值、升高吸附环境温度均有利于吸附反应的进行.粒径为0.097 ～0.15 mm的P(AA-AM)水凝胶粉末,在35℃、pH=5的条件下进行吸附等温线实验,得到水凝胶对重金属Cu2+,pb2+,Zn2+和Cd2+的理论最大吸附量分别为186,588,208和403 mg/g.P(AA-AM)水凝胶对重金属离子的吸附符合准二级动力学模型(R2＞0.98),吸附等温线符合Langmuir吸附等温线(R2＞0.95).干扰离子实验和理论模拟均证明P(AA-AM)水凝胶对pb2+具有良好的吸附性.     

不同海藻吸附重金属镉离子的研究

本文采用6种分别属于褐藻门、绿藻门、红藻门的海边常见大型海藻对重金属镉离子进行吸附比较实验，镉离子浓度较低时，其吸附容量排列顺序为：海黍子＞海带＞孔石莼＞节荚藻＞刺松藻＞内枝藻，海黍子的吸附量高达181mg/g，超出文献报道值，对3种吸附容量较高的海藻进行了较详细的研究，研究溶液的pH值、初始Cd^2 离子浓度等因素对Ca^2 的吸附特性的影响，对吸附机理进行了初步的探讨，发现镉离子与海藻中的钙离子发生离子交换作用，交换率占总吸附量的33－34％，得出了适宜的吸附等温线方程。     

巯基树脂对金属离子的吸附性能(Ⅱ)

研究了自合成的巯基树脂对重金属离子Ag 、Hg2 、Cr3 的吸附容量、吸附动力学、等温吸附过程等静态吸附性能,影响吸附的因素和吸附机理.结果表明,该树脂对上述3种离子吸附能力强,吸附量分别达6.56mmol/g、3.25mmol/g、2.10mmol/g.树脂对各重金属离子等温吸附在实验浓度范围内符合Langmuir或Freundlich方程.吸附机理研究表明,巯基与金属离子发生了离子交换和配位反应,化学吸附起支配作用;另外树脂对Ag 、Hg2 吸附过程中存在一定的氧化还原现象.     

THE THEORETICAL STUDY OF ADSORPTION OF METAL IONS ON CHITOSAN

1. INTRODUCTION Chitin, the most abundant natural amino polysaccharide and estimated to be produced annually almost as much as cellulose, is well known to consist of 2-acetamido-2-deoxy-β-D- glucose through α, β(1→4) linkage. Chitin is the major source of surface pollution in coastalareas. Chitosan is the N-deacetylated derivative of chitin and their structures are shown in Fig. 1. Fig. 1 Structures of Chitin and Chitosan Because of the excellent properties such as biocompatibility…     

Preparation, Properties and Mechanism of Inhomogeneous Calcium Alginate Ion Cross-linking Gel Microspheres

Inhomogeneous calcium alginate ion cross-linking gel microspheres,a novel ion absorbent,were prepared by dropping a sodium alginate solution to a calcium chloride solutioin via an electronic droplet generator.Calcium alginate microspheres have uniform particle sizes.a smooth surface and a microporous structure.The electrode probe reveals the inhomogeneous distribution of calcium ions with the highest concentration on the surface,and the lowest concentration in the cores of the spheres.As a novel ion adsorbent,calcium alginate gel microspheres have a lower limiting adsorption mass concentration,a higher enrichment capacity and a higher adsorption capacity for Pb^2 than usual ion exchange resins.The highest percentage of the adsorption is 99.79%.The limiting adsorption mass concentration is 0.0426mg/L.The adsorption capacity for Pb^2 is 644mg/g,Calcium alginate gel microspheres have a much faster ion exchange velocity than D418 chelating resin and D113 polyacrylate resin.The moving boundary model was employed to interpret the ion exchange kinetics process,which indicates that the ion exchange process is controlled by intraparticle diffusion of adsorbable ions.So the formation of inhomogeneous gel microspheres reduces the diffusion distance of adsorbable ions within the spheres and enhances the ion exchange velocity.Alginate has a higher selectivity for pb^2 than for Ca^2 and the selectivity coefficient KCa^Pb is 316. As an ion cross-linking gel,calcium alginate inhomogeneous microspheres can effectively adsorb heavy metal Pb^2 at a higher selectivity and a higher adsorption velocity.It is a novel and good ion adsorbent.     

微囊化海藻酸离子移变凝胶的制备、结构与性能

通过静电脉冲技术制备了海藻酸-壳聚糖-海藻酸(Alginate-Chitosan-Alginate,ACA)微胶囊,红外光谱分析表明,ACA是一种以聚电解质配合物为囊膜,以海藻酸钠离子吸附剂为囊心物的微胶囊型离子吸附体系.扫描电镜测试表明,ACA吸附重金属离子的过程是微胶囊囊内海藻酸凝胶化的过程,其解吸附过程是海藻酸凝胶转变成海藻酸溶液的过程.与传统离子交换树脂相比,ACA对Pb²⁺的吸附具有较高的去除率、很强的富集能力和较低的极限吸附浓度,并且能够被多次重复使用.ACA的离子交换速率比传统离子交换树脂快得多,离子交换过程中,交换离子和吸附剂海藻酸分子的相互扩散大大提高了离子交换速率.     

在多孔有机聚合物中构筑广谱性重金属离子吸附活性位

以三维刚性结构的三蝶烯为单体, 通过简单的Friedel-Crafts烷基化反应制备得到高比表面积的三蝶烯基多孔有机聚合物(TPOP), 在TPOP中接枝乙二胺和氯乙酸钠, 构建了广谱重金属离子吸附剂(TPOP-CH₂EDTA). 获得的TPOP-CH₂EDTA具有微孔/介孔结构, 其微孔尺寸为1.6 nm, BET比表面积为634 m²/g, 利于重金属离子传递和配位作用的强化. TPOP-CH₂EDTA对重金属离子具有吸附广谱性, 其对Ag(Ⅰ), Cu(Ⅱ), Ni(Ⅱ), Zn(Ⅱ), Co(Ⅱ), Sn(Ⅳ), Pb(Ⅱ), Cd(Ⅱ), Fe(Ⅲ)和Cr(Ⅲ)等10种重金属离子的去除率均高于98%. 以Pb(Ⅱ)为典型的重金属污染物, 通过Langmuir模型计算得到Pb(Ⅱ)的最大吸附容量高达184.5 mg/g; 具有拟二级吸附动力学特征, 吸附速率快, 动力学常数k₂为0.0173 g·mg^?1·min^?1; 经过5次循环使用后, Pb(Ⅱ)的去除效率仍高达95.8%. TPOP-CH₂EDTA对混合溶液中Pb(Ⅱ)和Cu(Ⅱ)的去除率均高于99%, 且对含有大量无机盐[如Ca(Ⅱ), Mg(Ⅱ), K(Ⅰ)和Na(Ⅰ)离子]和有机化合物的复杂真实水体系, Pb(Ⅱ)和Cu(Ⅱ)的去除效率仍高于90%. 因此, 通过调控多孔有机聚合物微观结构(如比表面积、 孔径和吸附位点密度)而构筑的广谱性重金属吸附材料, 为协同去除复杂水系统中混合重金属离子提供了方案.     

CMC-Na/DETA-B62型蛇笼树脂对金属离子的吸附性能

本文研究了自合成的蛇笼型螯合树脂-二乙烯三胺交联甘油环氧树脂/羰甲基纤维素体系对Cd^2 ,Pb^2 ,Fe^2 的吸附量，吸附动力学，等温吸附过程等静态吸附性能，同时研究了pH值等因素对吸附性能的影响。实验结果表明，该树脂对Cd^2 具有较强的吸附选择性，能在Cd^2 ,Pb^2 ,Fe^2 3种离子共存时选择吸附Cd^2 ，其选择性系数分别为Kcd^2 /pb^2 =3.77,Kcd^2 /Fe^2 =9.61。该树脂对上述3种离子的吸附量可分别达4.00,1.06,0.42mmol/g。该类树脂可用于含重金属离子污水的处理和金属离子的分离等方面。     

Synthesis and characterisation of poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS) Zr(IV) monothiophosphate composite cation exchanger: analytical application in the selective separation of lead metal ions

In this study, poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) zirconium(IV) monothiophosphate composite cation exchanger was prepared by sol–gel precipitation method. The presence of sulphur in the cation exchanger enhances affinity towards the heavy metal ions which can improve the selectivity of the material. The selectivity studies showed that the material is selective towards Pb(II) ions. To characterise the material, several physicochemical properties were also studied which includes X-ray, scanning electron microscopy and transmission electron microscopy studies. The ion-exchange behaviour of this cation exchanger was studied by using some of the selected properties like ion-exhange capacity for various metal ions, elution, effect of eluent concentration, thermal effect on ion-exchange capacity (IEC). The results of IEC and physicochemical properties revealed that the material is nanocomposite, crystalline, chemically, mechanically and thermally stable. The analytical ability of this cation exchanger was demonstrated in binary separation of Pb(II) ions from a mixture of other metal ions. The recovery is qualitative and the separations are reproducible.     

Ion exchange of Pb(2+), Cu(2+), Fe(3+), and Cr(3+) on natural clinoptilolite: selectivity determination and influence of acidity on metal uptake

In the present study ion exchange of Pb(2+), Cu(2+), Fe(3+), and Cr(3+) on natural Greek clinoptilolite was examined in terms of selectivity toward the above heavy metals in single- and multicomponent solutions in batch systems. Also examined are the influence of clinoptilolite on solution acidity and the effect of acidity on the ion exchange process. Clinoptilolite increases solution acidity due to the exchange of H(+) cations with the cations initially present in its structure. H(+) cations should be considered as competitive ones in ion exchange processes, and consequently ion exchange of metals is favored at high acidity values. Cu(2+) and Cr(3+) are the most sensitive cations with respect to acidity. Selectivity determination demonstrates that the selectivity at total concentration 0.01 N and acidity 2 in both single- and multicomponent solutions is following the order Pb(2+)>Fe(3+)>Cr(3+) > or =Cu(2+). This order is set since the first days of equilibration. However, Cu(2+) shows remarkable changes in selectivity and generally its uptake and selectivity are increasing with time. On the other hand selectivity in single metal solutions where acidity is not adjusted is following the order Pb(2+)>Cr(3+)>Fe(3+) congruent with Cu(2+).     

Highly efficient adsorption of Pb(II) by cubic nanocrystals in aqueous solution: Behavior and mechanism

As one of the most toxic heavy metal ions, lead pollution has become an urgent problem. Here, a cubic crystal nanoparticle (Prussian blue analogue, PBA), referred to as potassium manganese ferrocyanide (KMFC) was synthesized and used as a highly-effective sorbent for removing Pb(II) from aqueous solution. KMFC is a mesoporous material that has excellent ion exchange properties, which was confirmed by a series of characterizations. This paper investigated the adsorptive attributes of KMFC for lead ions in aqueous solution. The influences of temperature, contact time and pH on adsorption were studied in batch experiments. The KMFC possessed a robust adsorption capacity for resident lead ions in aqueous solution, which attained 1075.27 mg g⁻¹ at room temperature (25 °C), based on the Langmuir model, which was far higher than any previously reported values. The adsorption process was well fitted to a pseudo-second-order kinetic model, as well as Langmuir and Temkin isotherm models, and was endothermic and spontaneous on the basis of thermodynamic analysis. The adsorption of Pb(II) on the surface of KMFC started with electrostatic attraction, due to the electronegativity of KMFC. Further, ion exchange was the dominant mechanism in this adsorption process, which was confirmed by FTIR, XPS, and other supplementary experiments. The good chemisorption (K⁺ exchange) properties of KMFC suggested that it likely has excellent prospects in applications for heavy metal ions adsorption. This study not only provided a new perspective for the design and development of heavy metal sorbents but provided a deep insight into the mechanism of adsorption of heavy metal ions by PBA.