生物质焦油的催化裂解研究

对稻壳热解过程中产生的焦油进行了催化裂解研究。实验装置主体由裂解炉和固定床催化裂解反应器组成。研究得出催化裂解条件（温度、停留时间等）对焦油脱除的影响规律，并分析了生物质焦油催化裂解过程中发生的反应和焦油催化裂解机理。研究表明，白云石对焦油的催化裂解有较好的效果，随着温度和停留时间的增加，其催化裂解率提高。     

生物质流化床气化焦油析出特性的研究

生物质气化中焦油的存在严重地影响了气化设备的正常运行。为了了解生物质流化床气化过程中焦油的析出和脱除特性,以花生壳、稻草以及木屑为原料,采用流化床气化反应系统,研究了气化温度(750℃～850℃)、空气当量系数(0.15～0.35)以及催化剂(白云石、橄榄石与菱镁矿)的添加等对气体产物中焦油的析出组成特性的影响,并采用色谱 质谱联用仪对焦油的主要成分进行了分析。实验结果表明,随着温度的升高,焦油的量快速降低;催化剂的添加也有类似的结果。这说明高温和催化剂有利于大分子焦油的催化裂解。     

不同催化剂条件下高温煤气中焦油组分的催化裂解

高温煤气净化技术是正在开发的煤气化联合循环发电(ＩＧＣＣ)和煤气化燃料电池(ＭＣＦＣ)的关键技术之一。高温煤气中焦油蒸汽通过催化裂解方法去除,不但可以排除焦油堵塞管道,腐蚀设备,而且可以提高发电效率。Ｂａｋｅｒ等[1]对模拟煤气中焦油催化裂解研究得出:在450～690℃和1010～1818ｋＰａ的条件下,ＹＺ-Ｙ82催化剂最好,焦油转化率达74%,同时催化剂积炭最高达055ｇｇ焦油。Ａｚｎａｒ等[2]研究了Ｎｉ基催化剂对生物质气化气体中焦油的催化裂解得出:在780～830℃的温度下,所有催化剂对焦油的脱除都显示出很高的活性,反应时间48ｈ内催化…     

生物质焦油模型化合物催化转化实验研究

以苯和甲苯为焦油的模型化合物,在固定床反应器上研究了堇青石和白云石两种催化剂作用下,温度、蒸汽量和空速对焦油催化转化的影响。结果表明,苯和甲苯的转化率都随温度的提高和空速的降低而升高。在堇青石和白云石催化作用下,甲苯在裂解温度900℃,S/C摩尔比为1.5时转化率最高,转化率均达到95%。苯在裂解温度900℃,S/C摩尔比为1.0时转化率最高,转化率分别为61%和53%。蒸汽量的增大有助于裂解气体成分的调整。堇青石稳定性实验表明,积炭是造成催化剂活性降低的重要原因。     

甘油三酯裂解制备可再生液体燃料油研究

以碳酸钠为碱性催化剂,采用TG、DTG、DSC分析确定大豆油为原料的裂解特性。通过对四种典型裂解产物的跟踪测定,确证碱性催化剂能够改变大豆油裂解时的反应历程。分析结果表明,裂解温度在400℃~500℃,热解方式为快速热解。采用自行研制的小型滴流床反应器催化裂解大豆油。比较了不同催化剂的催化裂解性能,发现碱性催化剂具有较高的脱羧能力。在较佳催化裂解工艺条件下,所得燃料油酸值较低(30 mg KOH/g)。通过FT-IR、GC-MS以及燃料性能的分析,其组分和成分与0号柴油相似,热值43 M J/kg,黏度2.6 mm2/s,密度0.84 g/cm3。     

催化热解废轮胎制衍生油

催化热解废轮胎对于资源利用及环境保护具有重要意义,近年来引起人们关注.在废轮胎胶粉热解反应中加入催化剂,不仅会加速胶粉裂解速率,缩短反应时间,而且可以通过催化剂择形催化改变产物分布,从而提高目的产物衍生油的收率和性能.国内外对废轮胎催化热解已做了大量研究,以期提高衍生油中高附加值单环芳烃的含量,同时降低S, N和Cl含量,虽然已取得较大进展,但衍生油收率较低,大大降低了该技术的可行性.
　　本文采用带搅拌器的1000 mL不锈钢反应器,在常压条件下研究了反应温度和催化剂类型对废轮胎胶粉热解反应及产物衍生油性能的影响,通过元素分析、馏程模拟和色谱-质谱等表征手段检测了衍生油的理化性能.结果表明,在废轮胎胶粉热解反应过程中,随反应温度上升,出油速率先增加后降低.至500 oC时,热解衍生油收率最高达55.65 wt%,所得衍生油呈黑棕色,具有轻质油含量低、S和N含量高、粘度低和流动性好的特点,其轻质芳烃含量低,却含有大量可以转变为芳烃的脂肪烃类.因此,为了提高衍生油中轻质油和轻质芳烃收率,降低S和N含量,尽量维持较高的衍生油收率,在热解反应过程中引入少量ZSM-5, USY,β, SAPO-11和ZSM-22等常见催化剂,利用催化剂独特的孔道结构和酸分布,达到定向催化和转化的目的,提高轻质芳烃含量.同时,为了克服催化剂与胶粉难以接触进行反应的问题,在反应温度升至200 oC时,维持一定时间保证胶粉发生溶胀和液化反应形成液体烃类,使得催化剂不仅能够均匀分散于液体烃中与其接触进行反应,而且有效提高了反应物料与催化剂之间传质传热效率,使得裂解反应在均相中进行,降低因传热不均匀而造成的结焦和过度裂化反应.在催化热解过程中,1.0 wt%催化剂的加入可明显缩短反应时间,在保证衍生油收率基本不变的情况下,获得的衍生油呈黄棕色,轻质油收率较高为70–75 wt%, S和N含量分别降至0.3–0.58wt%和0.78–1.0 wt%.以具有较高酸性和孔径分布的ZSM-5, USY,β和SAPO-11为催化剂时,衍生油中总芳烃含量可达到50 wt%,其中单环芳烃含量高达45 wt%.     

催化热解废轮胎制衍生油（英文）

催化热解废轮胎对于资源利用及环境保护具有重要意义,近年来引起人们关注.在废轮胎胶粉热解反应中加入催化剂,不仅会加速胶粉裂解速率,缩短反应时间,而且可以通过催化剂择形催化改变产物分布,从而提高目的产物衍生油的收率和性能.国内外对废轮胎催化热解已做了大量研究,以期提高衍生油中高附加值单环芳烃的含量,同时降低S,N和Cl含量,虽然已取得较大进展,但衍生油收率较低,大大降低了该技术的可行性.本文采用带搅拌器的1000 mL不锈钢反应器,在常压条件下研究了反应温度和催化剂类型对废轮胎胶粉热解反应及产物衍生油性能的影响,通过元素分析、馏程模拟和色谱-质谱等表征手段检测了衍生油的理化性能.结果表明,在废轮胎胶粉热解反应过程中,随反应温度上升,出油速率先增加后降低.至500℃时,热解衍生油收率最高达55.65 wt%,所得衍生油呈黑棕色,具有轻质油含量低、S和N含量高、粘度低和流动性好的特点,其轻质芳烃含量低,却含有大量可以转变为芳烃的脂肪烃类.因此,为了提高衍生油中轻质油和轻质芳烃收率,降低S和N含量,尽量维持较高的衍生油收率,在热解反应过程中引入少量ZSM-5,USY,β,SAPO-11和ZSM-22等常见催化剂,利用催化剂独特的孔道结构和酸分布,达到定向催化和转化的目的,提高轻质芳烃含量.同时,为了克服催化剂与胶粉难以接触进行反应的问题,在反应温度升至200℃时,维持一定时间保证胶粉发生溶胀和液化反应形成液体烃类,使得催化剂不仅能够均匀分散于液体烃中与其接触进行反应,而且有效提高了反应物料与催化剂之间传质传热效率,使得裂解反应在均相中进行,降低因传热不均匀而造成的结焦和过度裂化反应.在催化热解过程中,1.0 wt%催化剂的加入可明显缩短反应时间,在保证衍生油收率基本不变的情况下,获得的衍生油呈黄棕色,轻质油收率较高为70–75 wt%,S和N含量分别降至0.3–0.58wt%和0.78–1.0 wt%.以具有较高酸性和孔径分布的ZSM-5,USY,β和SAPO-11为催化剂时,衍生油中总芳烃含量可达到50 wt%,其中单环芳烃含量高达45 wt%.     

MCM-41/SBA-15中孔分子筛对生物质热解油的催化裂解研究

以中孔MCM 41/SBA 15分子筛作催化剂，对不同条件下快速热解得到的木屑热解蒸气进行催化裂解，采用元素分析、凝胶色谱(s.e.c.)和气质联用（GC MS）等手段表征。结果表明,同未加催化剂比较，分子筛MCM 41/SBA 15的存在可使热解液体中氧的质量分数降低，长链化合物所占比例明显减小，其中SBA 15作催化剂比MCM 41作催化剂对热解蒸气裂解更容易得到接近柴油和汽油分子量的热解油，但芳香类化合物的质量分数明显增加。热解油中Pentadecane、Hexadecane、Dimethyjbenzene、Naphthalene等质量分数增加，而含氧类物质Methyl Phenol、2 Methoxy 4 Methyl Phenol、2 Methoxy 4 Propyl Phenol 等质量分数减少。     

移动床热煤气脱硫气固反应过程模拟：Ⅱ.错流移动床非催化气固反 …

基于前文错流移动床反应器模型方程,模拟计算并分析了该类反应器中气、固相流动对热煤气脱硫等非催化气固反应过程的影响。研究表明,床层在床深方向按反应速率的快慢可分为粗脱区和精脱区,在颗粒流动方向上气相浓度差异较大,并主要体现在粗脱区内,床层出口处颗粒转化呈现较大分布,反应器内气因交错流动,气相浓度的颗粒转化率共同作用（于气固反应速率）等因素是造成过程特征的主要因素。因此反应器优化应满足对两相流动的优化     

G—34型耐硫甲烷化催化剂的反应特性

报道了在钼系与氧化物系催化剂基础上开发的G-34型耐硫甲烷化催化剂的反应特性。它综合钼系和氧化物系二类催化剂的优点,获得了活性高、选择性好、对原料气中硫浓度不敏感,反应前可自然硫化,有良好稳定性的结果。此催化剂用于压力粗煤气提高热值较经济合理。可直接生产合格的城市煤气。     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.     

Copper-catalyzed multicomponent reactions of 2-iodoanilines,benzylamines, and elemental sulfur toward 2-arylbenzothiazoles

A relatively cheap copper salt-catalyzed, three-component approach providing 2-arylbenzothiazoles in good to excellent yields from readily available 2-iodoanilines, benzylamines, and sulfur powder is reported. This methodology allows preparation of various classes of 2-arylbenzothiazoles and provides a general, reliable approach.