多壁碳纳米管修饰电极分子印迹传感器测定咖啡因

以咖啡因为模板分子,通过电聚合邻苯二胺,在羧基化多壁碳纳米管修饰的玻碳电极表面制备了对咖啡因有特异响应的分子印迹聚合物膜。通过循环伏安法和线性扫描伏安法对传感器的性能进行表征,并优化了检测条件,研究了印迹传感器对模板分子咖啡因及其结构类似物的选择性响应。在最优实验条件下,电化学探针K3[Fe(CN)6]的峰电流与咖啡因浓度在2.0×10-7~2.0×10-5mol·L-1范围内呈良好的线性关系,检出限为4.0×10-8mol·L-1。该传感器应用于铁观音茶叶中咖啡因含量的测定,其回收率为94%~106%。     

盐酸克伦特罗在纳米ZnO和多壁碳纳米管修饰玻碳电极上的电化学行为

制备了纳米ZnO与多壁碳纳米管(MWNTs)复合修饰玻碳电极(ZnO-MWNTs/GCE),考察了盐酸克伦特罗(CLB)在该修饰电极上的电化学行为。实验结果表明:纳米ZnO与MWNTs显著增强了修饰电极对盐酸克伦特罗的伏安响应,增加了电极的有效表面积,改善了电极的导电性和电催化活性。在2~30μmol·L-1和30~500μmol·L-1浓度范围内,CLB在所制备的修饰电极上的电流响应与其浓度线性关系良好,且该电极具有较好的重现性和稳定性。     

盐酸普萘洛尔分子印迹电化学传感器的制备与研究

以盐酸普萘洛尔为目标模板分子,通过电聚合多巴胺,在多壁碳纳米管修饰的玻碳电极表面制备了对目标分子有特异响应的分子印迹电化学传感器.利用扫描电子显微镜、循环伏安法和差示脉冲伏安法对此传感器的表面形貌及性能进行了表征,并且优化了检测条件,研究了印迹传感器对模板分子及其结构类似物的选择性响应.结果表明:此传感器具有较好的选择性响应,而且碳纳米管的存在显著提高了传感器的灵敏度.盐酸普萘洛尔的浓度在0.20～100 μmol/L范围内与峰电流呈良好的线性关系;检出限为2.53×10-8 mol/L(S/N=3).此传感器还具有良好的稳定性和重现性.     

自组装碳纳米管-氯洁霉素分子印迹溶胶-凝胶电化学传感器研究

结合自组装技术, 采用电聚合方法在碳纳米管修饰金电极表面制备对氯洁霉素具有特异性识别位点的分子印迹溶胶-凝胶薄膜, 成功构建了一种新型印迹溶胶-凝胶电化学传感器. 通过循环伏安法(CV)、示差脉冲法(DPV)、安培计时法(I-t)和扫描电镜(SEM)表征了该印迹溶胶-凝胶膜的电化学性能和表面形貌. 结果表明, 该传感器具有良好的选择性和灵敏度, 氯洁霉素在多壁碳纳米管修饰的印迹溶胶-凝胶传感器上的响应明显提高. 该印迹溶胶-凝胶传感器对氯洁霉素的浓度响应线性范围为5.0×10^-7~8.0×10^-5 mol/L, 检出限为2.44×10^-8 mol/L. 该传感器被成功地用于人体尿液中氯洁霉素的分析测定.     

碳纳米管修饰电极分子印迹传感器快速测定沙丁胺醇

以单壁碳纳米管(SWNTs)为电极材料,应用分子印迹技术,以邻苯二胺为功能单体、沙丁胺醇为模板,采用电化学聚合法制备了一种新型的快速检测沙丁胺醇分子印迹传感器,并运用电化学方法去除模板.在磷酸盐缓冲溶液(PBS)中,利用线性溶出伏安法对印迹和非印迹膜的性能进行了比较,对分子印迹膜的影响因素进行了优化.实验表明,本传感器...     

碳纳米管修饰电极分子印迹传感器的制备及其对氧乐果的测定

以氧乐果为模板分子,邻苯二胺为功能单体,在碳纳米管修饰的玻碳电极表面通过电聚合方法制成氧乐果分子印迹聚合物膜,用无水乙醇洗脱后制备出对氧乐果有特异响应的电化学传感器。通过循环伏安法和电化学阻抗法对分子印迹传感器的电化学性能进行表征。以K_3Fe(CN)_6为探针,采用差分脉冲伏安法研究了该分子印迹传感器的分析性能,建立了氧乐果的间接测定方法。结果表明,K_3Fe(CN)_6的相对峰电流与氧乐果浓度在1.0×10~(-7)~2.0×10~(-6)mol/L范围内呈良好的线性关系,检出限为3.6×10~(-8)mol/L。     

应用门效应-分子印迹传感器测定盐酸强力霉素

利用邻苯二胺作为功能单体,盐酸强力霉素为模板分子,用电聚合的方法在金电极表面制备出对盐酸强力霉素可进行特异识别的分子印迹膜,利用门控制原理对盐酸强力霉素进行测定。表征了分子印迹膜的性能、印迹效应;试验了测定条件;该传感器对盐酸强力霉素的检测具有良好的选择性。盐酸强力霉素的浓度在2.0×10-9～1.0×10-7mol/L范围内与响应电流呈线性关系,检出限达8.7×10-10mol/L,低于现有分析方法。该传感器可用于鱼肉样品中盐酸强力霉素的检测,回收率在96.6%～103.1%。     

新型多壁碳纳米管/白藜芦醇印迹溶胶-凝胶层层组装电化学传感器研究

采用电化学沉积方法将印迹溶胶-凝胶膜沉积到功能化碳纳米管(MWNT-COOH)修饰的碳电极表面,成功研制一种新型多壁碳纳米管/白藜芦醇印迹溶胶-凝胶电化学传感器.采用扫描电镜(SEM),循环伏安法(CV),方波伏安法(SWV)和计时电流法(i-t)详细考察该印迹溶胶-凝胶膜的形态和电化学性能.结果表明该传感器对白藜芦醇具有较高的选择性和亲和性.与无多壁碳纳米管修饰的印迹传感器比较,MWNT层修饰的印迹传感器电流响应信号明显提高.白藜芦醇与印迹溶胶-凝胶膜的特异性结合使该传感器的电流发生变化,电流变化与白藜芦醇浓度在5.0×10-7～8.0×10-5mol?L-1范围内呈良好线性关系,检测限为5.1×10-8mol?L-1,该传感器成功应用于葡萄酒中白藜芦醇含量的检测.     

动物尿液中盐酸克伦特罗的分子印迹固相萃取-气相色谱-质谱法研究

采用分子印迹聚合物(MIP)固相萃取小柱提取、净化并富集猪尿液中的盐酸克伦特罗分子,用N,O-双三甲基硅基三氟乙酰胺(BSTFA)衍生化,毛细管气相色谱-质谱联用(选择离子模式,选择离子为277、262、243和86)对衍生物分析。优化了MIP固相萃取柱的淋洗条件,考察了MIP固相萃取柱的净化效果和消除基体干扰能力,建立了对动物尿液中盐酸克伦特罗的定性、定量分析的方法。在优化条件下,本法检出限(LOD)为0.51μg/L,定量限(LOQ)为1.00μg/L;不同盐酸克伦特罗加入量的回收率为71.0%~89.3%;相对标准偏差为3.2%~9.7%。将该方法与农业行业标准方法比较,结果吻合较好。但该方法灵敏度和精密度高,操作更为简单、快捷。     

Novel surface molecularly imprinted material modified multi-walled carbon nanotubes as solid-phase extraction sorbent for selective extraction gallium ion from fly ash

A new gallium (Ga(III)) ion-imprinted multi-walled carbon nanotubes (CNTs) composite sorbent was synthesized by a surface imprinting technique. The Ga(III) ion-imprinted/multi-walled carbon nanotubes (Ga(III)-imprinted/CNTs) sorbent was characterized by Fourier transform infrared (FT-IR), X-ray diffraction (XRD), nitrogen adsorption experiment, static adsorption experiment, and solid-phase extraction (SPE) experiment. The effects of sample volume, sample pH, washing and elution conditions on the extraction of Ga(III) ion from real sample were studied in detail. The imprinted sorbent offered a fast kinetics for the adsorption of Ga(III). The maximum static adsorption capacity of the imprinted sorbent towards was 58.8 μmol g⁻¹. The largest selectivity coefficient for Ga(III) in the presence of Al(III) was over 57.3. Compared with non-imprinted sorbent, the imprinted sorbent showed good imprinting effect for Ga(III) ion, the imprinting factor (α) was 2.6, the selectivity factor (β) was 2.4 and 2.9 for Al(III) and Zn(II), respectively. The developed imprinted SPE method was applied successfully to the detection of trace Ga(III) ion in fly ash samples with satisfactory results.     

Synthesis and application of multi-walled carbon nanotubes-molecularly imprinted sol-gel composite material for on-line solid-phase extraction and high-performance liquid chromatography determination of trace Sudan IV

A novel composite material of multi-walled carbon nanotubes (MWNTs)-Sudan IV molecularly imprinted polymers (MIPs) was prepared by surface molecular imprinting technique in combination with sol-gel technology. The MWNTs-MIPs were evaluated by scanning electron micrograph (SEM), Fourier transform infrared spectroscopy (FT-IR), and adsorption experiments. The results showed that the MWNTs-MIPs exhibited good selective recognition to Sudan IV. The maximum saturated binding capacity (Q_max) is 63.2 μmol g⁻¹. Applied as sorbent, the MWNTs-MIPs were used for the determination of trace Sudan IV in chilli powder by on-line solid-phase extraction-high-performance liquid chromatography (SPE-HPLC). The results showed that an enrichment factor of 741 was achieved with a loading flow rate of 1.0 mL min⁻¹ for sampling 50 mL. The MWNTs-MIPs provided a fast and convenience determination platform for Sudan IV in real samples.     

L-酪氨酸功能化多壁碳纳米管的制备及表征

采用L-酪氨酸作为修饰剂，制备了一种新型功能化的多壁碳纳米管，并对其进行了表征。红外光谱和电化学实验均证实碳纳米管和酪氨酸是通过酰胺键共价键合的。其中，循环伏安实验中0．22V处羧基峰的消失与红外光谱中1717cm^-1处N-酰化氨基酸的-C=O峰相对应，2931和2860cm^-1处的-CH2-的伸缩振动峰的出现证明了产物的形成。     

Sensitive and selective molecularly imprinted electrochemical sensor based on multi-walled carbon nanotubes for doxycycline hyclate determination

An electrochemical sensor for doxycycline hyclate(DC)detection with high sensitivity and good selectivity is reported.The sensor was fabricated by electro-polymerization of molecularly imprinted polymers(MIPs)in the presence of DC onto multi-walled carbon nanotubes modified glassy carbon electrode(MWCNTs/GCE).The MWCNTs can significantly increase the current response of the sensor,leading to enhanced sensitivity.The MIPs provide selective recognition sites for DC detection.The experimental parameters,such as the polymer monomer concentration,supporting electrolyte pH,the time for electro-polymerization and the incubation time of the sensor with DC were optimized.Under optimized experimental conditions,the sensor displayed a linear range of 0.05μmol/L-0.5μmol/L towards DC detection,with the detection limit of 1.3×10^-2μmol/L.The sensor was successfully applied for recovery test of DC in human serum samples.     

Influence of silver-decorated multi-walled carbon nanotubes on electrochemical performance of polyaniline-based electrodes

In this work, silver (Ag) nanoparticles were deposited on multi-walled carbon nanotubes (MWNTs) by chemical reduction while Ag-decorated MWNTs (Ag-MWNTs)/polyaniline (PANI) composites were prepared by oxidation polymerization. The effect of the Ag incorporated into the interface of the composites on the electrochemical performance of the MWNTs/PANI was investigated. It was found that highly dispersed Ag nanoparticles were deposited onto the MWNTs, and the Ag-MWNTs were successfully coated by PANI. According to cyclic voltammograms, the Ag-MWNTs/PANI exhibited significantly increased electrochemical performances compared to MWNTs/PANI and the highest specific capacitance obtained of MWNTs/PANI and 0.15 M Ag-MWNTs/PANI was 162 F/g and 205 F/g, respectively. This indicated that Ag nanoparticles that were deposited onto the MWNTs caused an enhanced electrochemical performance of the MWNTs/PANI due to their high electric conductivity, which resulted in an increase of the charge transfer between the MWNTs and PANI by a bridge effect.     

Preparation and electrocatalytic activities of platinum nanoclusters deposited on modified multi-walled carbon nanotubes supports

Multi-walled carbon nanotubes (MWNTs) were modified by oxyfluorination treatment at several different temperatures of 20, 100, 200, and 300 °C. The changes of surface properties of oxyfluorinated MWNTs were investigated using X-ray photoelectron spectroscopy (XPS) method. As a result, it was found that surface fluorine contents were varied with changing an oxyfluorination temperature and showed a maximum value at 100 °C. By changing the treatment temperature in the process of oxyfluorination for carbon supports, the surface characteristics of MWNTs had been modified, resulting that the size and loading content of deposited Pt on the modified carbon supports could be changed. Consequently, Pt deposited MWNTs that were treated at 100 °C (Pt/100-MWNTs) showed the best electroactivity among samples. The enhanced electroactivity was dependent on the higher surface area of electrochemical reaction for metal catalyst, which was related to the particle size and the morphology of the deposited particle catalysts.     

基于多壁碳纳米管/壳聚糖多层膜修饰玻碳电极邻苯二酚的测定

改进了碳纳米管在壳聚糖溶液中的分散方法,制备了多壁碳纳米管/壳聚糖多层膜修饰玻碳电极,对比了不同修饰层数膜电极的循环伏安和电化学阻抗行为,5层多壁碳纳米管/壳聚糖膜修饰玻碳电极的电化学性能优良.在最优实验条件下,该修饰玻碳电极对邻苯二酚(CAT)有灵敏的响应,CAT浓度在3.99×10-6～9.09×10-4mol/L范围内与氧化峰电流呈良好的线性关系,检出限为2.39×10-6mol/L(S/N=3).该修饰玻碳电极性能稳定,测定4×10-5mol/LCAT溶液,RSD(n=10)为2.1%;15周后,该电极的响应值仅降低1.9%.     

普鲁士蓝/多壁碳纳米管修饰电极测定维生素C

利用电化学方法在多壁碳纳米管修饰的玻碳电极表面聚合一层普鲁士蓝,制备普鲁士蓝/多壁碳纳米管修饰玻碳电极,运用循环伏安法研究了维生素C(vc)在该修饰电极上的电化学行为.该修饰电极对Vc显示出快速的电化学响应和较好的电催化活性,在pH为4.0的磷酸盐溶液中,Ve浓度与其氧化峰电流在8.0×10-4～1.0×10-2 mol/L范围内呈现良好的线性关系,相关系数为0.9993,检测限为6.4×10-5mol/L.该电极具有较好的稳定性和重现性.     

Impact behaviour of polypropylene filled with multi-walled carbon nanotubes

Multi-walled carbon nanotubes/polypropylene composites were compounded using a twin-screw extruder. Here, nanotubes with different lengths, i.e. 1-2 μm and 5-15 μm, respectively, were applied at a constant volume content of 1%. Notched Charpy impact tests showed that toughening effects of nanotubes depended highly on testing temperatures. The impact resistance was notably enhanced at a temperature above the glass transition temperature of matrix. Longer nanotubes performed more effective in toughening compared to the shorter ones. The increment of impact resistance of nanotube-filled polypropylene was considered due to enhanced load-carrying capability and much-increased deformation of matrix. SEM fractography further revealed the toughening mechanisms in a micro-scale. The impact energy was improved via nanotube breakage and pullout, which likely led to a series of energy consuming actions. In addition, the smaller spherulite size induced by nanotubes would be favourable to the impact resistance partially.     

Fabrication of a novel electrochemical sensor based on tin disulfide/multi-walled carbon nanotunbes-modified electrode for rutin determination in natural vegetation

A tin disulfide and multi-walled carbon nanotube (SnS₂/CNTs) electrochemical sensor was constructed for the sensitive and selective determination of rutin in plants. Tin disulfide nanoflowers with various particle sizes were prepared by controlling the reaction time and composited with multi-walled CNTs. The morphology, crystal structure, and chemical composition of these SnS₂/CNTs composites were characterized using XRD, XPS, and SEM-EDS. Results illustrated that the SnS₂/CNTs had a large specific surface area, good conductivity, and remarkable electrocatalytic performance. The pH of the buffer solution, the scanning rate, and the amount of modified material were also optimized for the rapid detection of rutin. A 2-electron-2-proton mechanism, involving a few rapid and consecutive stages, was speculated to occur during rutin oxidation, based on the observed slope of -53 mV/pH. There was an appreciable linear relationship between the reductive peak current from DPV and the rutin concentration, ranging from 0.005-0.05 µmol/L and 0.1-6 µmol/L, with a detection limit of 0.22 nmol/L (S/N = 3). The sensor also demonstrated good selectivity, excellent sensitivity, and reproducibility when analyzing rutin in real plant samples, with satisfactory recovery, and was also highly consistent with results of HPLC, and thus could be used to evaluate the medicinal value of natural vegetation.