Synthesis of TiO2 on different substrates by chemical vapor deposition for photocatalytic reduction of Cr(VI) in water

TiO₂ loaded on several substrates such as carbon fiber, aluminum plate, silica plate, and glass plate was prepared using the chemical vapor deposition (CVD) method for the photocatalytic reduction of Cr(VI) in water with the presence of ethanol under Ultraviolet (UV) illumination. As‐prepared samples were characterized by X‐Ray Diffraction (XRD), X‐ray photoelectron spectroscopy (XPS), Brunauer–Emmett–Teller (BET), and scanning electron microscopy (SEM). The catalyst with TiO₂ loaded on carbon fiber possessed an extremely large surface area (1,463,91 m²/g), while the other catalysts possessed small surface areas (0.05–0.21 m²/g). The photocatalytic activity of TiO₂ loaded on carbon fiber, which was determined by the conversion of Cr(VI) and the degradation of chemical oxygen demand (COD), was much higher than that of other catalysts. The reusability of TiO₂ loaded on carbon fiber catalyst exhibited almost the same activity as the fresh catalyst. The results indicated that TiO₂ loaded on carbon fiber is feasible for practical application.     

Electrospinning fabrication of mesoporous nano Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>-TiO<Subscript>2</Subscript>@activated carbon fiber membrane for hybrid removal of phenol from waste water

A mesoporous iron–titanium mixed-oxides@activated carbon(AC) fiber membrane was fabricated by an electrospinning method and applied to the treatment of phenol waste water. The physical and chemical properties of the composite fiber membrane were characterized by powder X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), N2 adsorption/desorption, UV–Vis light diffuse reflectance spectroscopy (DRS), Raman spectroscopy, respectively. The results indicate that the composite nanofiber membrane is composed of α-Fe₂O₃, anatase TiO₂ and activated carbon phases with a specific surface area of 231 m² g^–1 and narrow pore size distribution of 3–6 nm. DRS reveals that the composite membrane has high photons absorption from both ultraviolet light and visible light irradiation owing to the combination of Fe₂O₃, TiO₂ and carbon. The prepared nano Fe₂O₃–TiO₂@AC fiber membrane can act as an efficient reusable photocatalyst and adsorbent for 100% remo val of phenol pollutant. This hybrid technique is hopeful to be widely used in the treatment of various organic waste waters.     

One‐Pot Synthesis of Nitrogen‐doped TiO2 Nanowires with Enhanced Photocurrent Generation

A nitrogen‐doped TiO₂ (N‐TiO₂) nanowire film was synthesized via a one‐pot hydrothermal method using triethylamine as nitrogen source. The effect of the concentration of the triethylamine on the films was evaluated. In addition, the N‐TiO₂ nanowires were characterized using field‐emission scanning electron microscopy (FE‐SEM), X‐ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, and ultraviolet–visible spectroscopy. A 3.2× enhancement of the photocurrent for N‐TiO₂ (0.6) was achieved over the as‐prepared TiO₂ nanowire, under AM1.5G solar illumination. This was due to nitrogen doping, which could narrow the bandgap of titania to extend the adsorption of the catalyst to the visible light region.     

Influence of High-energy electron-beam on photocatalytic activity of TiO2 films on carbon-fiber deposited by atomic layer deposition

High-energy electron-beam with energy of 1 MeV was used for modifying surface structure of TiO₂ thin films on carbon fiber prepared by using atomic layer deposition under atmospheric pressure. TiO₂ nanoparticles (∼20 nm) on carbon fiber underwent structural modification of the surface upon electron-beam treatment, resulting in enhanced photocatalytic activity. In contrast, a thicker film of TiO₂ did not show such changes in surface structure and photocatalytic activity by electron-beam treatment. We demonstrate that electron-beam can be used for modifying surface structure of photocatalysts consisting of nanoparticles for improvement of their activity.     

Enhanced surface free energy of UHMWPE fibers and its interfacial adhesion behavior to PI resins

Mechanical properties of composites made up of ultra‐high‐molecular‐weight polyethylene (UHMWPE) fiber, polyimide (PI), and TiO₂ particles were investigated. The hybrid composite of 20 vol% of UHMWPE fiber with TiO₂ showed tensile strength greater than UHMWPE fiber/PI composite. A positive hybrid effect in tensile strength is obtained. It is observed that addition of small amount of TiO₂ to UHMWPE fiber/PI increased the tensile strength of the composite by 28%. With increase in TiO₂ loading to 1 to 3 vol%, the impact strength of the hybrid composite is increased from 55 KJ/m² to 69 KJ/m². This maximum value is more than one and a half times greater than the impact strength of neat UHMWPE fiber/PI composite.     

Effect of low current density electrochemical oxidation on the properties of carbon fiber‐reinforced epoxy resin composites

Changes in surface physicochemical structures of polyacrylonitrile‐based carbon fibers resulted from low current density electrochemical oxidation were monitored by scanning electron microscopy (SEM) and X‐ray photoelectron spectroscopy (XPS). The relationship between the interlaminar shear strength (ILSS) values of carbon fiber‐reinforced polymers (CFRPs) and carbon fiber surface chemistry including elemental ratios and the relative content of oxygen‐containing functional groups were researched. SEM results revealed that the electrochemical oxidation got rid of surface contaminants generated during the production process. XPS analysis showed that the relative contents of oxygen and nitrogen increased by 446% and 202%, respectively, after the electrochemical oxidation. Carbon fiber surface chemistry was of paramount importance to the interfacial properties of CFRPs. The higher the carbon fiber surface activity, the better the interfacial bonding was, and an increase in the acidic‐group contents was responsible for a higher ILSS value. However, when the current density increased to 1.0 A/m², the interfacial bonding between carbon fiber and the epoxy resin became weak which led to the decline in ILSS values. Copyright © 2012 John Wiley & Sons, Ltd.     

Preparation and photocatalytic activity of B,Ce Co-doped TiO2 hollow fibers photocatalyst

A series of B, Ce co-doped TiO₂ (B, Ce-TiO₂) photocatalytic materials with a hollow fiber structure were successfully prepared by template method using boric acid, ammonium ceric nitrate and tetrabutyltitanate as precursors and cotton fibers as template, followed by calcination at 500°C in an N₂ atmosphere for 2 h. Scanning electron microscopy (SEM), X-ray diffraction (XRD), nitrogen adsorption-desorption measurements, and UV-visible spectroscopy (UV-Vis) were employed to characterize the morphology, crystal structure, surface structure, and optical absorption properties of the samples. The photocatalytic performance of the samples was studied by photodegradation phenol in water under UV light irradiation. The results showed that the TiO₂ fiber materials have hollow structures, and the fiber structure materials showed better photocatalytic properties for the degradation of phenol than pure TiO₂ under UV light. In the experiment condition, the photocatalytic activity of B, Ce co-doped TiO₂ fibers was optimal of all the prepared samples. In addition, the possibility of cyclic usage of B, Ce co-doped TiO₂ fiber photocatalyst was also confirmed, the photocatalytic activity of TiO₂ fibers remained above 90% of that of the fresh sample after being used four times. The material was easily removed by centrifugal separation from the medium. It can therefore be potentially applied for the treatment of water contaminated by organic pollutants.     

Graphite-like carbon deposited anatase TiO<Subscript>2</Subscript> single crystals as efficient visible-light photocatalysts

Graphite-like carbon deposited single-crystal anatase TiO₂ with exposed {001} facets was fabricated through a two-step solvothermal process by using glucose as carbon source. The physicochemical properties of the as-prepared samples were investigated by X-ray diffraction, Brunauer-Emmett-Teller, transmission electron microscopy, Raman, UV–vis diffuse reflectance spectra, electrochemical impedance spectroscopy and surface photovoltage spectroscopy. These results demonstrated that graphite-like carbon layers were deposited on the surface of TiO₂ single-crystal nanosheets with exposed highly reactive {001} facets via the dehydration of glucose during the process of hydrothermal treatment. The loading of the graphite-like carbon layers could effectively extend the light absorption edge of the single-crystal anatase TiO₂ nanosheets to visible light region and accelerate the separation of photo-generated electrons and holes, contributing an excellent visible-light driven photocatalytic performance to the graphite-like carbon deposited single-crystal anatase TiO₂ nanosheets for the degradation of methyl orange.     

Preparation of Ce‐doped TiO2 Hollow Fibers and Their Photocatalytic Degradation Properties for Dye Compound

Cerium‐doped titanium dioxide (TiO₂) with a hollow fiber structure was successfully prepared using ammonium ceric nitrate and tetrabutyltitanate as precursors and cotton fiber as the template. The effects of cerium (Ce)‐doping on the crystallite sizes, crystal pattern, and optical property of the prepared catalysts were investigated by means of techniques such as scanning electron microscopy (SEM), X‐ray diffraction (XRD), BET surface area, and UV‐vis diffuse absorption spectroscopy. SEM observation showed that the prepared TiO₂ fibers possessed fibrous shape inherited from the cotton fiber and had a hollow structure. As confirmed by XRD and UV‐vis diffuse absorption spectroscopy examinations, Ce‐doping restrained the growth of grain size and extended the photoabsorption edge of TiO₂ hollow fiber into the visible light region. The present photocatalyst showed higher photocatalytic reactivity in photodegradation of highly concentrated methylene blue (MB) solutions than pure TiO₂ under UV and visible light, and the amount of Ce‐doped significantly affected the catalytic property. In the experiment condition, the photocatalytic activity of 0.5 mol% Ce‐doped TiO₂ fiber was optimal of all the prepared samples. In addition, the possibility of cyclic usage of the photocatalyst was also confirmed. The material was easily removed by centrifugal separation. Therefore, using the template method and by doping with cerium, TiO₂ may hopefully become a low‐energy consuming, high activity and green environmentally friendly catalytic material.     

具有高可见光催化活性的Ti3+和碳共掺杂改性的TiO2光催化剂

以乙醇为碳源,采用操作简单的真空活化法一步实现对TiO₂的Ti³⁺与C的共掺杂改性,TiO₂用X衍线衍射、紫外-可见光谱、顺磁共振、X射线光电子能谱和红外光谱等手段表征了催化剂的结构、组成、光学性质. 结果表明, 经Ti³⁺与C共掺杂改性后的催化剂表现出高的可见光降解甲基橙活性. 复合在催化剂表面的石墨可以增强催化剂对可见光的响应范围,而Ti³⁺与氧缺陷形成的掺杂能级则可以提高光生电子的迁移效率. 实验表明,两者之间的协同作用促进了其可见光催化活性的提高.     

蜂窝状Ho改性Fe-Mn/TiO2催化剂的制备及其低温选择催化还原(SCR)脱硝性能

采用模压法制备了蜂窝状Ho改性的Fe-Mn/TiO₂催化剂,研究了结构助剂、黏合剂和造孔剂等对成型催化剂低温选择催化还原（SCR）脱硝性能的影响。优选出一套理想的成型参数：水粉质量比为40%且逐次分批加入;结构助剂玻璃纤维的用量为10%（质量分数）;黏合剂羧甲基纤维素的用量为5%（质量分数）;助挤剂甘油的添加量为10%（质量分数）且分批加入;造孔剂活性炭粉的用量为2%（质量分数）。该蜂窝状催化剂在120 ℃下脱硝率维持在90%以上,并且在SO₂体积分数低于0.02%时具有一定的抗硫抗水性。表征结果表明,成型后蜂窝状催化剂比表面积降低,颗粒分散程度明显减弱,并且表面酸量和表面Mn⁴⁺含量下降,对催化活性有一定的影响。     

Improved solar-driven photocatalytic performance of BiOI decorated TiO2 benefiting from the separation properties of photo-induced charge carriers

In this work, BiOI decorated TiO₂ photocatalysts were prepared in-situ by a facile hydrothermal method and characterized by X-ray diffraction (XRD), UV/Vis diffuse reflectance spectroscopy, scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM), X-ray photoelectron spectroscopy (XPS) and surface photovoltage (SPV) spectroscopy. The reactive radicals during the photocatalytic reaction were detected by scavenger experiments. BiOI/TiO₂ composites exhibit higher performance than the pure TiO₂ towards photocatalytic decolorization of methyl orange (MO) aqueous solution, when the molar ratio of Bi/Ti is 2%, the sample has the highest photocatalytic activity. The enhanced photocatalytic performance of BiOI/TiO₂ could be ascribed to the separation properties of photo-induced charge carriers and strong interaction between BiOI and TiO₂. Based on the observations, a Z-scheme charge separation mechanism was proposed.     

Preparation and photocatalytic activity of TiO2-coated granular activated carbon composites by a molecular adsorption-deposition method

TiO₂ nanoparticle-coated granular activated carbon (GAC) composite photocatalysts (CPs) were successfully prepared by a molecular adsorption-deposition (MAD) method. The CPs were detected by scanning electron microscopy (SEM), X-ray diffraction (XRD), X-ray Photoelectron Spectroscopy (XPS), BET surface area and UV-Vis adsorption spectroscopy, and their photoactivity was evaluated by methyl orange (MO) photodegradation. The results show that small-sized TiO₂ nanoparticles were dispersed well, deposited on the surface of GAC, and showed slight blue shift in comparison with pure TiO₂. With the increase in TiO₂ content, the CPs showed band gaps in lower energy, smaller surface areas and the higher content of Ti³⁺ ions. Compared with pure TiO₂ and others CPs samples, CPs-382 sample showed the highest photoactivity due to the optimum TiO₂ content and surface area besides the synergic effect of photocatalytic degradation of TiO₂ and adsorptive property of GAC. In addition, the CPs could be very easily reclaimed, recycled and reused for methyl orange removal while high photoactivity is preserved.     

Improvement of interfacial adhesion performance of the kevlar fiber mat by depositing SiC/TiO2/Al2O3/graphene nanoparticles

Modern world seeks dramatic progress in composite materials use in numerous applications. Scientists worldwide are researching on fabricating new composites and attempting to have more applications using these materials. Serious attempts have also been taken to improve the properties of these materials. In this circumstance, a conscious attempt has been made in this present work that studies the effect of SiC/TiO₂/Al₂O₃/ graphene nanoparticles (NPs) deposition on Kevlar fiber. In this process, SiC/TiO₂/Al₂O₃/ graphene NPs have been deposited on Kevlar fiber by dip coating process. For the analysis, physical observation has been performed well at first which confirms nanoparticle deposition on the fiber and formation of adhesive bonding. SEM analysis followed by surface topography has been conducted to observe and further analysis of nanoparticle deposition. Atomic bonding mechanism shows how chemical bonding between fiber and nanoparticles. TGA analysis shows thermal improvement of the fiber by NPs deposition where graphene with binder makes 21.6% improvement in decomposition temperature. Tensile strength and young’s modulus of binder inclusion coated kevlar fabric are improved up to 26% and 5.7%, respectively. Finally, the IR-spectra confirms successful deposition of nanoparticles on the fiber.     

ELECTRODEPOSITION OF POLYMERS ON CARBON FIBERS

Styrene-co-maleic anhydride, vinyl acetate-co-maleic anhydride, methyl methacrylate-co-maleic anhydride copolymers were deposited on the surface of carbon fibers by an electrodcposition technique. The anion-free radical mechanism of this process and the physical adhesion to the surface were preliminarily confirmed. The adhesion at fiber-resin matrix interface in carbon fiber reinforced plastics was improved by the electrodeposited polymer interlayer and the shear failure occurred mainly in the matrix. Interlaminar shear strength of the unidirectional carbon fiber reinforced epoxy composite is increased from about 600 kg/cm~2 to 1000 kg/cm~2 by electrodeposition of polymers and the strength loss of the composite which has been immersed in boiling water for 100 hrs is decreased.     

Enhanced mechanical properties of carbon fiber composites by grafting different structural poly(amido amine) onto fiber surface

The mechanical properties of carbon fiber composites depend on the interfacial strength between fiber and epoxy matrix. Different poly (amido amine) (PAMAM) dendrimers were grafted onto carbon fiber to improve the interfacial strength of the resulting composites. Functional groups on the carbon fiber surface were examined by X-ray photoelectron spectroscopy. The surface morphology of the resulting materials was characterized by scanning electron microscopy and atomic force microscope. The characterization results revealed that PAMAM dendrimers were chemically grafted onto the surface of carbon fiber. More importantly, the mechanical properties of the resulting composites were enhanced owing to the presence of sufficient functional groups on the carbon fiber surface. In addition, after PAMAM containing chair conformations were grafted, the interlaminar shear strength had the highest increase of 53.13%, higher than that of the fiber grafted with PAMAM containing terminated linear amine. This work provides an alternative approach to enhance the mechanical properties of fiber composites by controlling the interface between fiber and epoxy matrix.     

Defect-assisted surface modification enhances the visible light photocatalytic performance of g-C3N4@C-TiO2 direct Z-scheme heterojunctions

To increase the number of active sites and defects in TiO₂ and promote rapid and efficient transfer of photogenerated charges, a g-C₃N₄@C-TiO₂ composite photocatalyst was prepared via in situ deposition of g-C₃N₄ on a carbon-doped anatase TiO₂ surface. The effects of carbon doping state and surface modification of g-C₃N₄ on the performance of g-C₃N₄@C-TiO₂ composite photocatalysts were studied by X-ray diffraction, X-ray photoelectron spectroscopy, UV-visible diffuse-reflectance spectroscopy, transmission electron microscopy, electrochemical impedance spectroscopy, photoluminescence, and electron paramagnetic resonance. With increasing carbon doping content, the carbon doping state in TiO₂ gradually changed from gap to substitution doping. Although the number of oxygen vacancies gradually increased, the degradation efficiency of g-C₃N₄@C-TiO₂ for RhB (phenol) initially increased and subsequently decreased with increasing carbon content. The g-C₃N₄@10C-TiO₂ sample exhibited the highest apparent reaction rate constant of 0.036 min^?1 (0.039 min^?1) for RhB (phenol) degradation, which was 150 (139), 6.4 (6.8), 2.3 (3), and 1.7 (2.1) times higher than that of pure TiO₂, 10C-TiO₂, g-C₃N₄, and g-C₃N₄@TiO₂, respectively. g-C₃N₄ was grown in situ on the surface of C-TiO₂ by surface carbon hybridization and bonding. The resultant novel g-C₃N₄@C-TiO₂ photocatalyst exhibited direct Z-scheme heterojunctions with non-local impurity levels. The high photocatalytic activity can be attributed to the synergistic effects of the improved visible light response ability, higher photogenerated electron transfer efficiency, and redox ability arising from Z-type heterojunctions.     

Decomposition of rhodamine 6G in the presence of titania coupling coupled with carbon source as photocatalyst under visible light excitation

Heterogeneous photocatalytic degradation of N-containing R6G dye was achieved by visible light-activated carbon doped TiO₂ (C-TiO₂) nanoparticles, synthesized by a low-temperature wet-chemical technique using glucose as carbon source. The structural and physicochemical properties of C-TiO₂ were characterized by X-ray diffraction (XRD), Raman spectroscopy, UV-vis diffuse reflectance spectroscopy (UV-vis DRS) and FT-IR spectroscopy. Compared with the pure TiO₂, the carbon modified nanomaterials exhibited enhanced absorption in the broad visible-light region together with an apparent red shift in the optical absorption edge. The resulting carbon-doped TiO₂ catalyst was employed as an effective photocatalyst for degradation of Rhodamine 6G (R6G) in aqueous solutions under visible light irradiation (λ > 420 nm). In addition, the intrinsic mechanism of visible light-induced photocatalytic oxidation of organic compounds on the carbon-doped titania was proposed and discussed.     

The Effect of SiO2 Addition on the Grain Size and Photocatalytic Activity of TiO2 Thin Films

The uniform transparent TiO₂/SiO₂ nanometer composite thin films were prepared via sol-gel method on the soda lime glass substrates, and were characterized by X-ray photoelectron spectroscopy (XPS), FTIR spectroscopy, UV-VIS spectroscopy, transmission electron microscopy (TEM), X-ray diffraction (XRD) and BET surface areas. It was found that the addition of SiO₂ to TiO₂ thin films could suppress the grain growth of TiO₂ crystal and increase the hydroxyl content of the surface of TiO₂ films. The photocatalytic activity of the as-prepared TiO₂/SiO₂ composite thin films increases for SiO₂ content of less than 5 mol%.     

Physical properties of nano-titania hollow fibers and their photocatalytic activity in the decomposition of phenol

A series of nano-titania (TiO₂) photocatalytic materials with a hollow fiber structure were successfully prepared using tetra-n-butyl titanate (Ti(OC₄H₉)₄) as precursor and cotton fiber as the template. Scanning electron microscopy (SEM), X-ray diffraction (XRD), and N₂ adsorption-desorption measurements were employed to characterize the morphology, crystal structure, and surface structure of the samples. The photocatalytic activities of the samples were studied by phenol photodegradation in water under UV irradiation. The effect of calcination temperature, photocatalyst dosage, initial concentration of phenol and irradiation time on the photodegradation of phenol was studied. Results showed that the TiO₂ fiber materials have hollow structures, indicating that these materials had a large specific surface area. The fiber structure material showed better photocatalytic properties for the degradation of phenol than pure TiO₂ under UV light, and the sample calcined at 500°C exhibited the highest phenol photodegradation efficiency. In addition, the possibility of cyclic usage of the photocatalyst was also confirmed, the photocatalytic activity of TiO₂ fiber remained ca. 90% of photocatalytic activity of the fresh sample after being used four times. Moreover, TiO₂ fiber was easily recovered by centrifugal separation from water.