土壤、沉积物系列标准物质中38种元素的ICP-MS定值

探讨了电感耦合等离子体质谱测定土壤元素的基体效应及元素间的基体干扰，采用模拟土壤元素天然组成比值的校正溶液，利用^115In-^103Rh双内标校正系统有效地抑制了分析信号的动态漂移，建立了测定土壤中元素的ICP－MS方法；对GBW07410－07416土壤、沉积物系列标准物质进行定值，测定结果与XRF分析结果比较，同时用于GBW07404、GBW07405、GBW07408、GBW07309管理样分析，结果令人满意。     

沸水浴-氢化物发生原子荧光光谱法测定土壤中的硒

沸水浴中王水消解土壤样品,加入尿素去除HNO_3,利用盐酸铁盐作为掩蔽剂消除共存元素干扰,首次建立了氢化物发生原子荧光光谱法测定土壤中硒的快速检测方法。经国家标准物质GBW07402、GBW07404和GBW07407验证,测定结果与标准值吻合,相对标准偏差(RSD)在0.57%~1.89%之间,加标回收率为94.00%~104.67%。方法检出限和测定下限分别为0.11 ng/mL和0.37 ng/mL。与其它消解方法对比,本方法消解时间为1 h,适用于土壤中硒的快速测定。     

高频红外碳硫分析仪测定石膏矿中的三氧化硫

利用高频红外碳硫仪对石膏矿中三氧化硫含量的测定进行了研究,取得了较好的结果.方法检出限为0.003 0%.用石膏标准样品(GBW03109a,GBW03110)进行分析,测定值与认定值相符,测定值的相对标准偏差(n=9)在0.32%~0.81%之间.使用石膏标准样品(GBW03111)进行本法与国标硫酸钡重量法做比对试验,测定结果无显著性差异.加标回收率为96.4%~104.0%.     

电感耦合等离子体发射光谱法测定植物中磷和钾

建立电感耦合等离子体发射光谱法测定植物中磷和钾的分析方法,以H₂SO₄-H₂O₂为消解体系,用电热板快速消解样品,在优化的仪器工作条件下进行测定。磷、钾的质量浓度在0.00～200.0μg/m L范围内与光谱强度具有良好的线性关系,相关系数均大于0.999,方法检出限分别为0.000 15%、0.001 3%,芹菜标准样品测定结果的相对标准偏差小于7%(n=10)。采用所建方法测定胡萝卜(GBW 10047)、芹菜(GBW 10048)、大葱(GBW 10049)标准样品,测定值均在标准值范围内,相对误差为0.3%～3.6%。该方法简便、快速,满足日常植物样品批量分析的要求。     

无公害蔬菜、灌溉水、种植土壤中Pb、As、Cd、Cr的测定

采用原子吸收光谱法测定了广西区内几个无公害生产基地土壤、蔬菜、水样中Pb、As、Cd、Cr的含量,RSD＜7％,回收率在94％－110％之间。用本法测定GBW 08302土壤标准物质,测得值与推荐值基本一致。     

ICP-MS测定农产品样品中6种痕量元素

建立了ICP-MS测定分析果蔬类、大米等农产品样品中痕量元素的方法。样品通过HNO3-H2O2混酸体系微波消解,以Rh作为内标溶液消除基体干扰,在仪器最佳条件下测定植物样中镉、铅、铬、铜、镍、锌六种痕量元素。结果表明：检出限为0.002～0.5ug/g ;相对标准偏差(RSD)为0.84% ~7.35% 。利用所建立的方法测定了大米(GBW10010)、小麦(GBW10011)、芹菜(GBW10048)、大葱(GBW10049)4种标准物质,分析结果均在参考值范围内。方法简单、快速、准确,适用于批量样品中多元素的同时测定。     

微波消解ICP-MS快速测定生物样品中的多种元素

建立了微波辅助HNO3消解样品,ICP-MS快速测定生物样品中Ti、Cr、Mn、Fe、Co、Ni、Cu、Zn、Ge、As、Se、Sr、Mo、Ag、Cd、I、Ba、Hg、Tl、Pb、Bi共21种微量及痕量元素。通过在线加入内标来校正基体效应和信号漂移对测量所造成的影响。各元素线性相关系数在0.9990以上,RSD小于6.0%。用本方法对国家标准样品GBW07601a(头发),GBW10010(大米),GBW10016(茶叶),GBW10023(紫菜)进行分析,结果满意。方法能满足生物样品痕量分析的要求。     

ICP-AES和ICP-MS法测定光学玻璃中的15种稀土元素

采用Na₂O₂熔融分解样品,运用电感耦合等离子体发射光谱法（ICP-AES）和电感耦合等离子体质谱法（ICP-MS）测定光学玻璃中的稀土元素。采用该方法对国家一级标准物质GBW07158、GBW07159、GBW07160和GBW07161进行测定,其结果表明与标准值相符。方法选择性好、灵敏度好、定量准确,适用于光学玻璃中稀土元素的测定,结果令人满意。     

王水溶样-电感耦合等离子体质谱（ICP-MS）法测定地质样品中的金

称取10.00 g样品放于马弗炉中700℃条件下焙烧后,加入约60 mL王水,盖上表面皿于低温电热板(1000 W)溶解40 min,加入5 mL动物胶(20 g/L),搅拌均匀后加入等体积的水,抽滤,滤液定溶至500 mL,分液后以10 ng/mL的Rh为内标建立了王水溶样-电感耦合等离子体质谱(ICP-MS)法快速测定地质样品中金的分析方法。方法适用于检测0.1~10μg/g品位的矿石样品,对国家一级标准物质GBW07209、GBW07808、GBW07809、GBW07300进行12次测定,其相对标准偏差RSD均小于5%,相对误差RE均小于2%。方法具有简单快速等优势,在实际应用中得到满意的结果。     

电感耦合等离子体质谱法测定重晶石中的微量元素

重晶石样品(0.200 0~0.250 0g)经氢氟酸(6mL)、盐酸(3mL)和硝酸(1mL)溶样,蒸干,最后用盐酸(1+3)溶液4mL溶解残渣,加水定容至100mL。采用电感耦合等离子体质谱法测定其中锶、铝、钙、镁、钾、钠、铜、铅、锌等9种微量元素的含量。用一级标准物质(GBW07811、GBW 07814、GWB 07812)绘制标准曲线,以铼为内标物。方法的检出限在2.2×10-7~1.51×10-6之间。方法用于实样分析,测定值的相对标准偏差(n=10)在2.2%~3.8%之间。应用此方法分析了4种重晶石标准物质(GBW 07813、GBW 07815、GBW 07816、GBW 07817),所得测定值与认定值相符。用标准加入法做方法的回收试验,测得回收率在90.0%~120%之间。     

Determination of mercury in biological tissues by graphite-furnace atomic absorption spectrometry with an in-situ concentration technique.

A method has been described for the determination of total mercury by graphite-furnace atomic absorption spectrometry (GFAAS) using an in-situ concentration technique with a Pd-Zr coating and a chemical modifier. The characteristic mass, which gives an integrated absorbance of 0.0044 s, was found to be 42 pg and an absolute detection limit (3sigma) of 33 pg was obtained with the proposed modifier. The total mercury values in standard reference materials, including Mussel (GBW08571), Bovine liver (GBW08306), Peach leaf (GBW08501) and Tea leaf (GBW080001), were determined using the proposed method, and the results were consistent with reference values. The method had been successfully applied to the determination of mercury in biological tissue samples with a recovery range of 94-105%.     

石墨炉原子吸收测定土壤中的Cd Pb

摘要：为了提升石墨炉原子吸收测定土壤样品中Cd和Pb的准确度和测试效率,对样品前处理和仪器测试等条件进行优化选择,确定了低温电热板消解样品时,硝酸、氢氟酸、高氯酸的三酸比例和复溶方式以及采用海光GGX-920型石墨炉原子吸收测定Cd和Pb的升温程序、样品和基体改进剂加入量等条件。应用选定方法条件分别对土壤标准物质GBW07403、GBW07449水系沉积物 GBW07309进行6次测定,测定值Cd的相对标准偏差RSD：2.49%~4.67%,相对误差RE：-2.31% ~ 2.22%,测定值Pb的相对标准偏差RSD：1.98%~ 2.54%,相对误差RE：-1.88% ~ 2.11%。此方法精密度和准确度均达到标准要求,是一种准确而快速的检测方法,适合大批量的环境样品检测。     

微波消解-ICP—MS法同时测定砖茶中的铅、铜、铬和16种稀土元素

采用微波消解处理样品,以电感耦合等离子质谱（ICP-MS）法同时测定砖茶中的铅、铜、铬和16种稀土元素。采用外标法绘制校准曲线,分析了茶叶国家标准物质GBW 10016,测定值与标准值吻合。检出限为0．055-0．765μg／蚝,样品测定结果的相对标准偏差为0．2％～4．7％（n=6）。用加标回收的方法评价了该方法的准确性,回收率为88．0％-102．7％。该方法测定结果与电热板湿法消解前处理测定结果相比差异不显著。     

Determination of Ultra-Trace Platinum,Palladium, Ruthenium,Rhodium, and Iridium in Rocks and Minerals by Inductively Coupled–Plasma Mass Spectrometry Following Nickel Sulfide Fire Assay Preconcentration and Open Mixed Acid Digestion

Platinum (Pt), palladium (Pd), ruthenium (Ru), rhodium (Rh), iridium (Ir), and osmiun (Os) are platinum-group elements with similar physic-chemical properties, and have important applications in geochemistry and environmental chemistry. However, due to their low abundance and inhomogeneous distribution in natural ores as well as the nugget effect, the accurate determination of the platinum-group elements has been a challenge for geological analysis. In this work, self-prepared and purified sodium carbonate (NiCO₃) instead of commercial nickel oxide (NiO) was used as the fire assay collector in order to greatly reduce the reagent blank and method detection limits. In addition, the fuming time of HClO₄ was strictly controlled at 10?min and a high sensitive method was developed for the simultaneous determination of ultra-trace Pt, Pd, Ru, Rh, and Ir in minerals by inductively coupled plasma-mass spectrometry (ICP-MS) following preconcentration with the nickel sulfide fire assay. Under the optimized conditions, the linear ranges of Pt, Pd, Ru, Rh, and Ir were between 0 and 100?ng mL^?1, with correlation coefficients exceeding 0.9997. The detection limits were 0.015, 0.056, 0.014, 0.004, 0.012?ng mL^?1 (for 10?g sample) for Pt, Pd, Ru, Rh and Ir, respectively. The developed method was successfully applied to analyze Chinese Certified Reference Materials (CRMs) GBW07288, GBW07289, GBW07290, GBW07291, GBW07292, GBW07293, GBW07294, GBW07101, GBW07102 and GBW07201 and the determined values were in good agreement with the certified values. The relative standard deviations (n?=?5) of Pt, Pd, Ru, Rh and Ir were between 3.42% and 6.87% for the determination of GBW07291.     

一体化碰撞反应 (iCRC)-电感耦合等离子体质谱法测定地质样品中痕量稀土元素

钡以及轻稀土元素氧化物对中、重稀土元素的干扰一直是质谱测试中存在的问题。建立了石墨粉垫底碳酸钠-硼酸混合熔剂熔融前处理样品,以_¹⁰³Rh为内标校正,一体化碰撞反应-电感耦合等离子体质谱仪法测定地质样品中稀土元素含量的方法。探讨了碳酸钠-硼酸混合熔剂熔融前处理样品注意事项、碰撞模式下碰撞气流量和离子透镜的参数的优化、干扰校正试验等问题,采用国家标准物质GBW07403、GBW07405、GBW07427、GBW07429验证,实验结果表明,各元素线性关系良好,相关系数均大于0.999,方法检出限在0.01～0.03mg/kg之间,相对误差为0.13%～7.1%,相对标准偏差为0.79%～6.59%,测试结果与标准值相吻合。对实际样品分析,得到平滑的球粒陨石归一化的稀土元素配分曲线,证明测定结果是合理可信的。该方法熔剂用量少,过程空白低,对器皿的侵蚀小,直接加热浸取,简化了操作过程,适用于大批量地质样品中稀土元素的测定。     

X射线荧光光谱法测定化探样品中主、次和痕量组分

采用粉末样品压片制样，用PW2440X射线荧光光谱仪对化探样品中氯、溴、硫、氧化钠、氧化镁、三氧化二铝、二氧化硅、磷、氧化钾、氧化钙、钛、锰、三氧化二铁、钴、铌、锆、钇、锶、铷、铅、钍、锌、铜、镍、钒、铬、钡、镧、铈、钕、钪、镓、砷、铪等34个组分进行测定。讨论了微量元素的背景选择和谱线重叠校正及氯测定的问题。使用经验系数法和康普顿散射线作内标校正基体效应，经标准物质检验，分析结果与标样值吻合，用GBW 07308国家一级标准物质作精密度试验，统计结果RSD（n=12）除砷、钒、镍、铜〈6．0％，溴、硫、铈、铪、钕、钪、氧化钠、镧、铬、钴和钍〈14．0％以外，其余各组分均小于3．0％。     

电感耦合等离子体原子发射光谱(ICP-AES)法测定硫化物矿石中的铜铅锌

建立了电感耦合等离子体原子发射光谱(ICP-AES)法同时测定硫化物矿石中Cu、Pb、Zn三种元素的方法,取代了传统的四酸(HCl+HNO3+HClO4+HF)溶样法,采用简单的盐酸和硝酸溶解矿石,大大缩短了分析时间。选择干扰少且灵敏度高的谱线作为待测元素的分析谱线,采用左右两点扣背景的方法校正光谱干扰和基体匹配方法消除物理干扰,用GBW07162和GBW07163等不同种类的国家一级标准物质进行精密度和准确度实验,测定结果的相对标准偏差都在10%以内,测定结果都在标准值的误差范围内,符合地质矿产开发的要求。     

ICP-AES determination of trace rare earth elements in environmental and food samples by on-line separation and preconcentration with acetylacetone-modified silica gel using microcolumn.

A novel method of online microcolumn separation and preconcentration coupled to inductively coupled plasma atomic emission spectrometry (ICP-AES) with the use of acetylacetone-modified silica gel as packing material was developed for the determination of trace rare earth elements (REEs) in environmental and food samples. The main parameters affecting online separation/preconcentration, including pH, sample flow rate, sample volume, elution and interfering ions, have been investigated in detail. Under the optimized operating conditions, the adsorption capacity values for Sc, Y, La, Ce, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho, Er, Tm, Yb and Lu were 25.65, 23.23, 24.01, 19.40, 22.89, 23.77, 24.40, 23.96, 25.58, 25.15, 24.86, 22.75, 16.05, 24.13, 26.51 and 27.93 mg g(-1), respectively. Detection limits (3sigma) based on three times standard deviations of the blanks by 8 replicates were in the range from 48 pg mL(-1) for Lu to 1003 pg mL(-1) for Sm. With 90 s preconcentration time and 10 s elution time, the enrichment factor was 10 and the sample frequency was 28 h(-1). The precisions (RSDs) obtained by determination of a 250 ng mL(-1) (n = 8) REEs standard solution were in the range from 1.7% for Y to 4.4% for Sm. The proposed method was successfully applied to the determination of trace REEs in pig liver, agaric and mushroom. To validate the proposed method, we analyzed three certified reference materials (GBW07401 soil, GBW07301a sediment, and GBW07605 tea leaves). The determined values were in a good agreement with the certified values. The method is rapid, selective, sensitive and applicable to the determination of trace REEs in biological and environmental samples with complicated matrix effects.     

Selective preconcentration of thallium species as chloro and iodo complexes on Chromosorb 105 resin prior to electrothermal atomic absorption spectrometry

A selective preconcentration method was described for the determination of inorganic thallium species by electrothermal atomic absorption spectrometry (ETAAS). Thallium(III) and thallium(I) as chloro and iodo complexes were selectively retained by a column containing 0.5 g of Chromosorb 105 resin and quantitatively eluted by 10 mL of pure acetone. The calibration graph was linear with a correlation coefficient of 0.997 at levels near the detection limit and up to at least 0.8 μg L⁻¹. The detection limits for the determination of total thallium and thallium(III) employing the proposed method by ETAAS were estimated as three values of the standard deviations, 0.050 μg L⁻¹ and 0.034 μg L⁻¹, respectively. Verification of the accuracy was carried out by the analysis of standard reference materials (GBW 07402 soil, NIST 2710 Montana soil, GBW 07309 and GBW 07310 stream sediments). The relative errors were found to be in the range of −7.7% to +4.8%. The relative standard deviations were generally found to be below 10%. The effect of potential interfering ions on the determination was studied. The proposed method was successfully applied to the determination of total thallium in five different brand cements, soils around two cement plants and metallic zinc samples. The speciation of thallium(I) and thallium(III) was applied to synthetic solutions.