Dispersive liquid–liquid microextraction using the freezed floating organic drop for rapid,fast, and sensitive determination of lead

A rapid, simple, and sensitive method was developed for lead preconcentration and separation in various real samples by dispersive liquid–liquid microextraction based on the freezing of floating organic drop. In this method, a suitable extraction solvent dissolved in a dispersive solvent was quickly syringed into the water sample so that the solution became turbid. Then, two phases were separated by centrifugation. The floating extractant droplet can be easily solidified on an ice bath and taken out of the water sample. Then, it can be liquefied instantly at room temperature, and analyte can be determined in it. In the creation of a hydrophobic complex with lead, 1-(2-pyridylazo)-2-naphthole (PAN) was used as the chelating agent. 1-Undecanol and acetone were used as extraction and disperser solvent. To achieve the highest recovery, some factors (type and volume of dispersive and extraction solvent, pH, PAN concentration, and salt concentration) were optimised. Under optimised conditions (pH = 9, 1.0 × 10^–3 mol L^?1 PAN, 15% w/v NaCl, 100 µL 1-undecanol, and 0.3 mL acetone), the lead calibration graph was linear from 1.5 to 80 μg L^?1. The detection limit and preconcentration factor were 0.5 μg L^?1 and 50, respectively. Lead was successfully determined in water and food (spinach, rice, potato, carrot, and black tea bag) samples by this method.     

Supramolecular-based solvent microextraction of carbaryl in water samples followed by high performance liquid chromatography determination

In this study, a simple, rapid, low cost, sensitive and environmentally friendly technique, supramolecular solvent microextraction (SM-SME) followed by high performance liquid chromatography-ultraviolet has been proposed to extract carbaryl from water samples. Parameters, affecting the SM-SME performance such as the weight of decanoic acid (DeA), volume of tetrahydrofuran (THF), pH and salt concentration, were studied and optimised. The effect of the pH on the extraction efficiency was evaluated by one–factor-at-a-time methodology, but the other variables were optimised by a face-centred cube central composite design methodology. Optimum extraction conditions were obtained: DeA: 70 mg; THF: 650 µL; salt concentration: 10% (w/v) NaCl and pH = 2–4), and the performance of the proposed method was evaluated. Under the optimum conditions, good linearity (1.0–500 µg L^?1, r² = 0.9994) was obtained. Limit of detection and limit of quantification were 0.3–1.0 µg L^?1, respectively. Also, the recoveries of the carbaryl were obtained in the ranged from 96% to 105%. Finally, proposed method was successfully applied for the determination of the carbaryl in the water samples of farms run-off and rivers and satisfactory results were obtained.     

Supramolecular microextraction of cobalt from water samples before its microsampling flame atomic absorption spectrometric detection

The supramolecular solvent system consists of tetrahydrofuran (THF) and 1-decanol, that was used as an extraction solvent for a microextraction procedure for the preconcentration and separation of Co(II). The proposed supramolecular-based procedure was combined with microsampling flame atomic absorption spectrometry for the determination of cobalt at trace levels in water samples. N-Benzoyl-N,N-diisobutylthiourea was used to chelate Co(II) in an aqueous solution. Quantitative extraction efficiency was obtained at pH 6.5. The effects of analytical parameters including pH, amount of ligand, type, ratio and volume of supramolecular solvent, sample volume and interfering ions were investigated for optimisation of the procedure. The proposed supramolecular solvent-based microextraction procedure (Ss-ME) exhibits a limit of detection (LOD) of 1.29 µg L^?1 and a limit of quantification (LOQ) of 3.88 µg L^?1. The procedure was validated by addition/recovery tests and by applying TMDA 64.2 and TMDA 53.3 water certified reference materials. The microextraction method was successfully applied for the preconcentration and determination of cobalt in water samples.     

Effect of Mercury(II) Traces on Catalytic Activity of Peanut and Horseradish Peroxidases

Abstract

Mercury(II) in the range of 0.1–1 µg L^?1 concentrations was found to be a much more efficient inhibitor of native peanut peroxidase (PNP) than of horseradish peroxidase (HRP) in the reaction of o‐dianisidine oxidation with hydrogen peroxide. The possible reason for the different degree of mercury(II) effects on the catalytic activity of both enzymes was studied. It was shown that the different number of glycans in PNP and HRP molecules (three and eight, respectively), or their absence in the molecule of wild‐type recombinant horseradish peroxidase refolded from E. coli inclusion bodies (recHRP), does not play a significant role in the effects caused by mercury(II). The efficient inhibition of PNP by mercury(II) in the absence of any other additives (for example, thiourea) originates from a greater mobility of the distal calcium ion in the enzyme molecule. A model scheme for the interaction of the studied plant peroxidases with mercury(II) was proposed. The PNP‐based enzymatic method for mercury(II) determination with c _min =0.04 µg L^?1 (0.2 nmol L^?1) was developed and the possibility of PNP application for analysis of different samples was demonstrated.     

Simultaneous Determination of Nickel and Cobalt as Chelates with 1-(2-Pyridylazo)-2-naphthol Using an LC Switching Column Method

A simple liquid chromatographic method was developed for the separation and simultaneous determination of cobalt and nickel as chelates with 1-(2-pyridylazo)-2-naphthol (PAN). The method, using a switching column technique for the on-line purification and separation, enables to reach the sub-microgram per litre concentration level excluding off-line sample treatment with the exception of the derivatization reaction. Two small-sized columns packed with CN- and C₄-bonded stationary phases were selected and used considering their complementary behaviour with respect to chelated Co and Ni ions. The analysis was performed within 10 min using an optimised eluent (water–acetonitrile–methanol–tetrahydrofuran, 40:45:10:5, v/v/v/v) containing Tween 40 (10^?3 M) and acetate buffer (5 × 10^?3 M, pH 4.8). Detection was performed by UV-vis spectrophotometry (λ = 565 nm) permitting to reach quantification limits of 0.9 and 0.5 μg L^?1 for Co and Ni, respectively.     

β-Cyclodextrin-Cross-Linked Polymer as Solid Phase Extraction Material Coupled Graphite Furnace Atomic Absorption Spectrometry for Separation/Analysis of Trace Copper

Abstract

The β-cyclodextrin cross-linked polymer (β-CDCP) was synthesized by the reaction of β-cyclodextrin with epichlorohydrin in NaOH and characterized by fourier transform infrared spectroscopy and thermoanalysis. The β-CDCP as a solid phase extraction (SPE) material was used to preconcentrate/separate trace copper using l-(2-pyridylazo)-2-naphthol (PAN) as a complexing agent for Cu-(II)-PAN coupled with a graphite furnace atomic absorption spectrometry (GFAAS) for analysis. The optimized experiment conditions and adsorption capacity were investigated. The detection limit (DL) was 1.11 µg.L^?1 with RSD 4.27% (n = 5, c = 25.0 µg L^?1). The linear range is 6.25–31.25 µg L^?1. Moreover, the β-CDCP could be used repeatedly and offered better a recovery and estimation of trace copper. In order to verify the accuracy of the method, a certified reference water sample was analyzed and the results obtained were in agreement with the certified values. The recovery for copper was 103.6%. The proposed method was applied to the analysis of copper in lake water samples.     

Development of sequential injection spectrophotometric method for determination of mercury (II) using pyrogallol red

A sequential injection analysis (SIA) spectrophotometric method for the determination of trace amount of mercury (II) with pyrogallol red (PGR) was described. The method was based on the measurement of absorbance of the mercury (II)–PGR complex, yielding a light yellow-coloured product at pH 9.0 with absorption maximum at 370 nm. The SIA parameters affecting the signal response were optimised in order to obtain the better sensitivity and minimum reagent consumption. The linear range for determination of mercury (II) was over the range of 0.1–2.0 mg L^?1. The limit of detection and limit of quantification, calculated following IUPAC were 0.06 and 0.10 mg L^?1, respectively. The repeatability was 1.25% (n = 10) for 0.5 mg L^?1 of mercury (II). The proposed method was successfully applied to determine the mercury (II) in commercial cosmetics, local Thai traditional medicines and water samples with a sampling rate of 40 h^?1. Results obtained were in justifiable agreement with those obtained by the official ICP-MS method at the 95% confidence level.     

Solid-phase extraction of Pb2+ ion from environmental samples onto L-AC-Ag-NP by flame atomic absorption spectrometry (FAAS)

The development of a solid-phase extraction (SPE) procedure for the pre-concentration of trace amounts of Pb²⁺ ion on 2-furan-2-yl-1-furan-2-ylmethyl-1H-benzoimidazole loaded on activated carbon modified with silver nanoparticles (L-AC-Ag-NP) was presented. The metal ion retained on the sorbent was quantitatively determined via complexation with the ligand. The complexed metal ion was efficiently eluted using 10 mL of 4 mol L^?1 sulphuric acid in 10 w/v% acetone. The influences of the analytical parameters, including pH, amounts of the ligand and the solid phase, eluent conditions and sample volume, on the recoveries of the metal ion were optimised. Using the optimised parameters, the linear response of the SPE method for Pb²⁺ ion were in the ranges of 0.2–160 µg L^?1, and the detection limit for Pb²⁺ ion was 0.034 µg L^?1. The proposed method exhibits a pre-concentration factor (PF) of 80 and an enhancement factor of 30 for Pb²⁺ ion. The presented results demonstrate the successful application of the proposed method for the determination of Pb²⁺ ion in some real samples with high recoveries (>93%) and reasonable relative standard deviation (RSD < 2%).     

Mercury speciation by a high performance liquid chromatography—atomic fluorescence spectrometry hyphenated system with photo-induced chemical vapour generation reagent in the mobile phase

Speciation of mercury was accomplished by using a simple interface with photo-induced chemical vapour generation in a high performance liquid chromatography—atomic fluorescence spectrometry (HPLC-AFS) hyphenated system. Acetic acid and 2-mercaptoethanol in the mobile phase were used as photochemical reagent. The operating parameters were optimized to give limits of detection of 0.53 µg L^?1, 0.22 µg L^?1, 0.18 µg L^?1 and 0.25 µg L^?1 for inorganic mercury, methylmercury, ethylmercury and phenylmercury, respectively. The method was validated with the certified reference material DORM-2 and applied to the analysis of seafood samples. The HPLC-AFS hyphenated system is simple, environmentally friendly, and represents an attractive alternative to the conventional peroxothiosulfate-borohydride method.     

Use of clinoptilolite loaded with 1-(2-pyridylazo)-2-naphthol as a sorbent for preconcentration of Pb(II), Ni(II), Cd(II) and Cu(II) prior to their determination by flame atomic absorption spectroscopy

A solid phase extraction system for separation and preconcentration of trace amounts of Pb(II), Ni(II), Cd(II) and Cu(II) is proposed. The procedure is based on the adsorption of Pb²⁺, Ni²⁺, Cd²⁺ and Cu²⁺ ions on a column of 1-(2-pyridylazo)-2-naphthol (PAN) immobilised on surfactant-coated clinoptilolite prior to their determinations by Flame Atomic Absorption Spectroscopy (FAAS). The effective parameters including pH, sample volume, sample flow rate and eluent flow rate were also studied. The analytes collected on the column were eluted with 5 mL of 1 mol L^?1 nitric acid. A concentration factor of 180 can be achieved by passing 900 mL of sample through the column. The detection limits (3 s) for Cd, Cu, Pb and Ni were found to be 0.28, 0.12, 0.44 and 0.46 µg L^?1, respectively. The relative SDs at 10 µg L^?1 (n = 10) for analytes were in the range of 1.2–1.4%. The method was applied to the determination of Pb, Ni, Cd and Cu in water samples.     

Speciation and determination of chromium ions by dispersive micro solid phase extraction using magnetic graphene oxide followed by flame atomic absorption spectrometry

A selective, simple and fast dispersive micro solid phase extraction method using magnetic graphene oxide (GO) as an efficient sorbent has been developed for the extraction, separation and speciation analysis of chromium ions. The method is based on different adsorption behaviour of Cr(VI) and Cr(III) species onto magnetic GO in aqueous solutions which allowed the selective separation and extraction of Cr(VI) in the pH range of 2.0–3.0. The retained Cr(VI) ions by the sorbent were eluted using 0.5 mL of 0.5 mol L^?1 nitric acid solution in methanol and determined by ?ame atomic absorption spectrometry. Total chromium content was determined after the oxidation of Cr(III) to Cr(VI) by potassium permanganate. All effective parameters on the performance of the extraction process were thoroughly investigated and optimised. Under the optimised conditions, the method exhibited a linear dynamic range of 0.5–50.0 µg L^?1 with a detection limit of 0.1 µg L^?1 and pre-concentration factor of 200. The relative standard deviations of 3.8% and 4.6% (n = 8) were obtained at 25.0 µg L^?1 level of Cr(VI) for intra- and inter-day analysis, respectively. The method was successfully applied to the speciation and determination of Cr(VI) and Cr(III) in environmental water samples.     

Multivariate Analysis for the Classification Differentiation of Brazilian Sugarcane Spirits by Analysis of Organic and Inorganic Compounds

Abstract

Brazilian sugarcane spirits were analyzed to elucidate similarities and dissimilarities by principal component analysis. Nine aldehydes, six alcohols, and six metal cations were identified and quantified. Isobutanol (LD 202.9 µg L^?1), butiraldehyde (0.08–0.5 µg L^?1), ethanol (39–47% v/v), and copper (371–6068 µg L^?1) showed marked similarities, but the concentration levels of n-butanol (1.6–7.3 µg L^?1), sec-butanol (LD 89 µg L^?1), formaldehyde (0.1–0.74 µg L^?1), valeraldehyde (0.04–0.31 µg L^?1), iron (8.6–139.1 µg L^?1), and magnesium (LD 1149 µg L^?1) exhibited differences from samples.     

Two new Cu(II) m-hydroxybenzoato complexes with chloro- and carboxylato-bridged dinuclear [Cu(µ2−Cl)(µ2−COO)Cu] cores

In aqueous methanolic solution, reactions of CuCl₂, m-hydroxybenzoic acid (HL), and NaOH with 2,2'-bipyridine (bpy) and 1,10-phenanthroline (phen) at room temperature afforded {[Cu(bpy)L](µ₂?Cl)(µ₂?L)[Cu(bpy)L]}?1.2H₂O (1) and {[Cu(phen)Cl](µ₂?Cl)(µ₂?L)[Cu(phen)L]} (2) with chloro- and carboxylato-bridged dinuclear [Cu(µ₂?Cl)(µ₂?COO)Cu] cores. The Cu₂ dimers in 1 are pairwise aggregated to form H-bonded tetranuclear motifs, which are extended by H₂O into 1-D H-bonded chains and further assembled into 2-D supramolecular networks. The Cu₂ dimers in 2 are also linked into 1-D H-bonded chains and further assembled into 2-D supramolecular layers. Magnetic measurements indicate that significant antiferromagnetic interactions (J = ?15.9, ?12.2 cm^?1) between Cu²⁺ ions are dominant in these dinuclear [Cu(µ₂?Cl)(µ₂?COO)Cu] cores. To the best of our knowledge, 2, crystallizing in the acentric polar orthorhombic space group Pna2₁, represents the first example of metal m-hydroxybenzoato complexes with ferroelectric properties with a remnant polarization (Pr) of ca. 0.04?µC cm^?2, coercive field (Ec) of ca. 2.52 kV cm^?1, and saturation of the spontaneous polarization (Ps) at ca. 0.195?µC cm^?2.     

Enhanced Selectivity and Sensitivity for Flow Injection Spectrophotometric Determination of Cobalt Using Solid Phase Extraction with a 2D Ion-Imprinted Adsorbent

The present work reports the effectiveness of a 2D imprinting method based on a surface imprinting technique for the development of a selective and sensitive flow sorbent preconcentration system for Co²⁺ ion determination. Cobalt ions were determined by UV-vis spectrophotometry exploiting the complexation with 1-(2-piridylazo)-2-naphtol (PAN). Based on a coefficient of relative selectivity (k'), the ion-imprinted amino-functionalized silica gel sorbent (ISG), compared with modified but non-imprinted sorbent (MSG) and silica gel (SG), showed a very high selectivity. A limit of detection of 0.51 µg L^?1 and precision (n = 10) as a relative standard deviation of 2.63 and 1.50% for Co²⁺ concentration of 10.0 and 90.0 µg L^?1, respectively, were achieved. A comparison of the proposed method with other previously published methods shows advantages in terms of sample consumption, sample throughput, and limit of detection. The application of the present method was successfully performed for the direct determination of Co²⁺ content in urine and environmental water samples without any interference and without sample preparation, with satisfactory results.     

Extraction and separation of zirconium from hafnium by using nano-structured supramolecular solvent microextraction method

In the present study, a simple versatile extraction method based on supramolecular solvent microextraction followed by inductively coupled plasma atomic emission spectrometry was developed for the extraction, separation and determination of zirconium (Zr) from hafnium (Hf). Zr and Hf were complexed with bis(2,4,4-trimethylpentyl) phosphinic acid, to obtain hydrophobic complex, and extracted into supramolecular solvent phase. The effective parameters on the supramolecular solvent microextraction efficiency were studied and optimized by using two different optimization methods: one variable at a time and central composite design. Under the optimum conditions, the linear range of 0.3–200.0 and 2.0–200.0 µg L^?1, detection limits (S/N = 3) of 0.1 and 0.6 µg L^?1, and precisions (n = 5) of 3.2–4.9% and 3.0–5.1% were obtained for Zr and Hf, respectively. Finally, the proposed method has been successfully applied for the extraction and separation of these cations in zirconium ore sample.     

Supramolecular solvent microextraction of Sudan blue II in environmental samples prior to its spectrophotometric determination

A liquid phase microextraction method-based conformation of supramolecular assembly was developed for the separation and preconcentration of trace levels of Sudan blue II. Various analytical parameters such as pH, supramolecular solvent type and volume, sample volume and matrix effect etc. were optimised. Sudan blue II concentration in the extraction phase was determined by UV-visible spectrophotometer. Under the optimised conditions, detection limit and preconcentration factor was found as 2.16 µg L^?1 and 80, respectively. Relative standard deviation value was found 5%. The developed procedure was successfully applied for the determination of trace levels of Sudan blue II in environmental samples.     

Graphene oxide reinforced polyamide nanocomposite coated on paper as a novel layered sorbent for microextraction by packed sorbent

ABSTRACT

In this work, a novel layered sorbent for microextraction by packed sorbent (MEPS) was introduced, which has been prepared by coating graphene oxide/polyamide (GO/PA) nanocomposite (NC) onto cellulose paper through solvent exchange method. Scanning electron microscopy (SEM) was applied to investigate the surface characteristic and morphology of PA and GO/PA NC coated on cellulose paper. The prepared MEPS device was used for extraction of organophosphorous pesticides (OPPs) including chlorpyrifos, fenthion, fenithrothion, ethion, edifenphos and phosalone in environmental aqueous samples followed by detection using gas chromatography-flame ionisation detector (GC-FID). Important parameters affecting the MEPS method including pH of sample solution, extraction draw-discard cycles, sorbent layers, desorption solvent volume and desorption draw-eject number were studied and optimised using central composite design (CCD). Based on the method validation, limits of detection (LODs) were in the range of 0.2–1 µg L^?1. The calibration graphs for chlorpyrifos, fenthion and edifenphos are linear in the concentration range of 1 to 500 µg L^?1; for ethion and phosalone are linear in the range of 1–1000 µg L^?1 and for fenithrothion is linear in the range of 3–1000 µg L^?1. The method precision (RSD %) with six replicates determinations was in the range of 3 to 9.4 % and 3.9 to 11.9% for distilled water and spiked river water sample, respectively, at the concentration level of 300 µg L^?1 . The developed method was applied successfully to determine OPP compounds in river, dam and tap water samples; accordingly, the relative recoveries (RR%) were obtained in the range of 77.8 to 113.3%.     

Selective extraction and preconcentration of ultra-trace amounts of arsenic(V) ions using carbon nanotubes as a novel sorbent

In the present study, multiwalled carbon nanotubes (MWCNTs) as solid phase extraction sorbent were developed for preconcentration of arsenic(V) species prior to graphite furnace atomic absorption spectrometry (GFAAS) determination. Arsenic(V) was selectively sorbed on the packed column with MWCNTs within a pH 9.5 in the presence of 2-(5-bromo-2-pyridylazo)-5-diethyl amino phenol (5-Br-PADAP). The adsorbed species was then desorbed with 1 mL of 2.0 M HNO₃. Experimental parameters including pH, sample volume and flow rate, type, volume and concentration of eluent that influence the recovery of the arsenic(V) species were optimised. Under the optimised conditions, the calibration curve was linear in the range of 0.2–10.0 µg L^?1 with detection limit of 0.016 µg L^?1. The relative standard deviations (RSD) for seven replicate determinations at 1.0 µg L^?1 level of arsenic was 6.69%. The proposed method was successfully applied to the determination of arsenic in water samples and certified reference material (NIST RSM 1643e).     

Dispersive Liquid–Liquid Microextraction of Silver Prior to Determination by Microsample Introduction-Flame Atomic Absorption Spectrometry

Abstract

A new simple and sensitive method has been proposed for rapid determination of trace levels of silver in environmental water samples, using dispersive liquid–liquid microextraction (DLLME) prior to its microsample introduction-flame atomic absorption spectrometry. Under the optimum conditions, the linear range was 0.1–7 µg L^?1 and limit of detection was 0.018 µg L^?1. The relative standard deviation for 0.50 and 5.00 µg L^?1 of silver in water sample was 4.0 and 1.7%, respectively. The relative recoveries of silver from tap, well, river, and seawater samples at spiking levels of 1.00 and 5.00 µg L^?1 were in the range of 86.4–98.6%.     

Adsorptive Stripping Voltammetric Determination of Antimony by Using Alizarin Red S

Abstract

A sensitive and selective voltammetric method for determination of antimony(III) using Alizarin Red S (ARS) as complexing agent is described. The method is based on the monitoring the oxidation peak of antimony(III)-ARS complex at ?520 mV in ammonium-ammonia buffer (pH = 7.5). The peak current was measured by scanning the potential from ?700 mV versus Ag/AgClto more positive potentials without accumulation in the presence of 1 × 10^?6 mol L^?1 of ARS. The limit of detection (3 s) and limit of quantification (10 s) of the method were calculated from calibration curve as 1.45 µg L^? and 4.8 µg L^? respectively. The calibration plot for antimony(III) was linear in the range of 4.8–30 µg L^?. The interference of various ions was examined. Serious interference from Al(III), Fe(III), Cu(II), Pb(II), and Zn(II) was eliminated by addition of EDTA to the solution. The method was applied to drinking water samples. The recoveries were in the range 94% – 105%. The results obtained from the developed method were compared with those from the differential-pulse anodic-stripping method and no statistically significant difference was found.