Au／ZnO催化剂的制备及常温条件下CO氧化催化性能

用共沉淀法制备了n(Au)/n(ZnO)=1.3/100的催化剂,考察了焙烧温度对Au/ZnO催化剂的化学组成及CO氧化性能的影响,结果表明,焙烧温度对催化剂的化学组成、活性和稳定性均有较大影响,其中240℃7焙烧制得的Au/ZnO催化剂稳定性最好,在25℃和进料中含有水分的条件下,可连续反应600h使CO完全转化,XRD,FTIR,TG－DTA,TEM及UV－Vis结果表明,金粒子高度分散在氧化锌或碳酸锌上,平均直径2－5nm,催化剂的稳定性同锌物种有关,氧化锌较碳酸锌表面出较好的稳定性,且氧化锌粒子越小,比表面积越大,催化剂的稳定性越高。     

Ni/Al2O3催化剂上甲烷三重整制合成气

制备了负载于大孔容、高比表面的γ-Al2O3载体上的Ni基催化剂.采用固定床流动反应装置,考察了催化剂焙烧温度、反应条件(反应温度、压力、空速以及反应原料气组成)对甲烷三重整反应(TRM)制合成气的催化性能的影响.结果表明,650℃焙烧的催化剂具有较好的稳定性.在常压、850℃、10080h-1、n(CH4)/n(CO2)/n(H2O)/n(O2)=1/0.48/0.54/0.1的条件下,CH4转化率达到95.4%,CO2转化率达到84.6%,在此条件下连续运行9h未见活性下降.TRM反应适宜于在高温、低压下进行,原料组成的变化不会影响CH4转化率,但会影响CO2转化率和产物合成气的n(H2)/n(CO)比.     

用辛烷基硫醇单层保护Au纳米粒子制备CO氧化催化剂Au/γ-Al2O3

采用两相法合成出含活性组分Au的辛烷基硫醇单层保护Au纳米粒子(C8AuNPs)的正己烷溶胶, 用“逐次浸润”法将C8AuNPs负载在γ-Al2O3上, 经真空干燥及活化处理制得Au/γ-Al2O3催化剂. 所制得的Au催化剂前体C8AuNPs/γ-Al2O3表面Au粒子平均粒径可控制在2-3 nm范围内, 且分布比较单一; 催化剂活性评价600 h后, 其表面Au的粒径仍主要分布在2-4 nm范围内; 真空干燥温度影响Au催化剂的粒子尺寸和催化活性, 随着真空干燥温度的提高, Au纳米粒子的粒径增大. 将所制备的催化剂用于低温CO氧化反应, 催化活性评价结果表明, 经25 ℃真空干燥制得的2.5%(质量分数, w)Au/γ-Al2O3具有较高的活性和长期稳定性, 其催化CO完全转化的最低温度为-19 ℃, 在15 ℃下CO完全转化时Au/γ-Al2O3的单程寿命至少900 h; 4.0%(w) Au/γ-Al2O3在15 ℃和进料中含水条件下对CO完全氧化的单程寿命不低于2000 h, 可见催化剂具有强的抗潮湿中毒特性. 综合上述实验结果, 讨论了影响Au/γ-Al2O3催化剂活性的可能因素.     

Au/Fe2O3催化剂的制备及其对富氢气体中一氧化碳选择性氧化的催化性能

 采用共沉淀法制备了1.5%Au/Fe2O3催化剂,考察了加料方式对Au/Fe2O3催化剂化学组成及其催化富氢气体中CO选择性氧化性能的影响. 结果表明,正加法制备的Au/Fe2O3催化剂的性能明显好于反加法制备的催化剂,80 ℃时前者对富氢气体中CO选择性氧化反应的转化率为94%,CO2选择性为65%,连续反应10 h,催化剂活性没有变化. XRD,XPS和TEM等的测试结果表明,正加法制备的Au/Fe2O3催化剂中金粒子的平均粒径为2～4 nm,金粒子高度分散在载体上,并与载体之间发生了较强的相互作用,从而表现出较高的催化性能.     

微乳法制备Au/Al2 O3 催化剂及其催化氧化CO性能的研究

用Tx-100／正己醇／环己烷／水的W／O微乳体系,合成了一系列Au／Al2O3催化剂。考察了焙烧温度、沉淀剂种类、搅拌方式等对Au／Al2O3,催化氧化CO活性的影响。结果表明：以氨水为沉淀剂,机械搅拌,600℃焙烧制得的Au／Al2O3,显示出较好的CO氧化性能。当反应温度为100℃时,CO转化率达85．0％,240℃时转化率达96．0％。XRD,DTA,TPR和TEM等表征表明：低温焙烧的催化剂,大部分载体Al2O3为无定型,对催化活性不利;焙烧温度过高,可能造成金微粒的团聚烧结,使其活性下降;由较强烈的搅拌方式制得的Au／Al2O3经适宜温度焙烧,可获得金粒尺寸较小、CO催化氧化活性较高的Au／γ-Al2O3催化剂。     

CuZnAl水滑石衍生催化剂上甲醇水蒸气重整制氢Ⅰ. 催化剂焙烧温度的影响

 以类层柱CuZnAl水滑石为前体,经不同温度焙烧制备了一系列甲醇水蒸气重整制氢催化剂. 在250 ℃、 水/甲醇比1.3和重时空速2.5 h-1下的反应结果表明, 600 ℃焙烧的催化剂具有优异的活性和稳定性,而≤500 ℃和≥700 ℃焙烧后的催化剂活性较差. 热重、 X射线衍射、 傅里叶变换红外光谱和程序升温还原分析结果表明, 600 ℃焙烧时水滑石分解较为完全,析出纳米CuO粒子的同时伴生CuAl2O4尖晶石相,进而在反应过程中对金属Cu纳米粒子和ZnO起到良好的隔离和稳定作用. 焙烧温度≥700 ℃时CuO纳米粒子发生二次团聚,同时CuAl2O4尖晶石相大量生成,造成催化活性位减少,活性较低; 而焙烧温度≤500 ℃时水滑石分解不完全,生成 (Cu,Zn)AlxOy(CO3)z复合物且无尖晶石相伴生,造成反应中金属Cu纳米粒子和ZnO聚集,导致催化剂活性较低.     

氧化锌纳米线外延生长PdZn纳米粒子的制备及在甲醇水蒸气重整反应中的催化性能

以采用改进的气相沉积法制备的具有规整{1010}晶面的氧化锌纳米线为载体,合成了氧化锌纳米线负载钯催化剂,考察了还原温度和负载量对催化剂表面形成Pd Zn合金过程的影响,并通过适当的后处理过程制备了氧化锌纳米线外延生长Pd Zn纳米粒子催化体系.结果表明,当金属钯负载量较低(质量分数约为2%)时,经400℃还原后的催化剂表面会形成PdxZny(xy)合金,从而影响催化剂的CO选择性;提高钯负载量或还原温度有利于将PdxZny(xy)合金转化为Pd Zn合金,降低CO选择性.负载Pd Zn合金纳米粒子与氧化锌纳米线载体之间外延生长的界面关系使其在甲醇水蒸气重整反应中显示出优异的反应稳定性.     

沉淀剂种类对水煤气变换Au/Fe2O3催化剂结构和催化性能的影响

 采用7种沉淀剂(K2CO3, Na2CO3, NH4OH, (NH4)2CO3, NaOH, KOH和尿素)通过共沉淀法制备了低温水煤气变换(WGS) Au/Fe2O3催化剂,考察了沉淀剂种类对其催化性能的影响. 通过N2吸附, X射线荧光光谱、 X射线衍射、 H2程序升温还原和CO程序升温脱附等表征手段,探讨了不同沉淀剂影响Au/Fe2O3催化剂WGS性能的原因. 结果表明,采用K2CO3和Na2CO3制备的催化剂样品在200 ℃以上具有较好的活性和稳定性,其中K2CO3是最佳沉淀剂. 而采用NH4OH和(NH4)2CO3制备的样品的催化活性相对较低,在200 ℃达到峰值. 由其它3种沉淀剂制备的样品的催化活性都较差, CO转化率最高只有35%. 沉淀剂种类不仅明显地影响金离子和铁离子的共沉淀,而且会明显地影响共沉淀物在后续焙烧过程中的结晶行为. 前者将影响金的负载量,后者则影响金粒子的分散度以及氧化铁载体的还原性质和对CO的吸脱附性能. Au/Fe2O3催化剂的低温高活性及其稳定性归因于高度分散的金粒子及其与易被还原的氧化铁载体间的协同作用. 催化剂中金负载量增大、金粒子分散度提高以及氧化铁晶粒减小均有利于其催化性能的提高.     

沉淀剂对AU/ZnO催化剂CO氧化性能及催化剂结构的影响

在25 C和进料中含水条件下,考察了由Na2CO3,(NH4)2CO3,NaOH和NH4OH等4种沉淀剂制备的Au/ZnO催化剂上CO氧化活性和稳定性.结果表明,沉淀剂影响Au/ZnO催化剂的前体组成、金粒子和ZnO粒子大小、比表面积及CO氧化性能.由NH4OH制备的Au/ZnO催化剂活性和稳定性较差,CO转化率只有15%;由其它3种沉淀剂制备的Au/ZnO催化剂的CO氧化活性和稳定性明显改善,可至少连续反应1 100 h,且保持CO完全氧化,其中Na2CO3是最佳沉淀剂.在反应过程中反应气氛可引起金粒子的聚集及在催化剂表面生成新的碱式碳酸锌物相.催化剂的稳定性与金粒子长大速度和碳酸根累积量有关.     

常温常湿条件下Au/MeO~x催化剂上CO氧化性能

利用共沉淀法制备了Au/MeO~x催化剂(Me=Al,Co,Cr,Cu,Fe,Mn,Ni,Zn)。在常温常湿条件下,考察了不同氧化物负载的金基催化剂的CO氧化性能。结果表明,氧化物种类对催化剂的活性和稳定性均有较大的影响。Cu,Mn,Cr等氧化物负载的金基催化剂的活性较差,而Zn,Fe,Co,Ni,Al等金属氧化物负载的金基催化剂可将CO完全氧化,又具有一定的稳定性,在相同反应条件下,CO完全转化时的稳定性顺序为Au/ZnO>Au/α-Fe~2O~3>Au/Co~3O~4>Au/γ-Al~2O~3≈Au/NiO。还发现水对Au/MnO~x催化剂的活性和稳定性有负作用,而对180℃焙烧制备的Au/ZnO-180催化剂的活性和稳定性均有明显的湿度增强作用。     

预处理条件对Au/ZnO催化剂CO氧化性能的影响

采用沉积沉淀法制备了用于CO氧化的Au/ZnO催化剂, 并用程序升温还原(TPR), X射线衍射(XRD)和透射电镜(TEM)技术对催化剂进行了表征. 结果表明: 采用沉积沉淀法可制备出高度分散的Au/ZnO催化剂; 提高焙烧温度导致金颗粒聚集长大, 样品经533, 673, 773 K焙烧后金物种的颗粒尺寸分别为2.7, 3.5, 3.7 nm. 催化剂的TPR表征结果中发现部分还原态的金物种在室温就可被氧化, 催化剂预先用流动空气处理可提高其氧化还原性, 样品经多次氧化还原循环后, 其氧化循环性能没有明显下降. CO的氧化反应结果表明, 焙烧温度强烈影响催化剂对CO的氧化活性, 533 K焙烧后的催化剂活性最高. 即使在反应气中含水3.1%(体积比)的湿气条件下, 反应300 h后, CO的转化率仍然保持在95%.     

Gold catalysts supported on ZnO/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> for low-temperature CO oxidation

Gold catalysts with loadings ranging from 0.5 to 7.0 wt% on a ZnO/Al₂O₃ support were prepared by the deposition–precipitation method (Au/ZnO/Al₂O₃) with ammonium bicarbonate as the precipitation agent and were evaluated for performance in CO oxidation. These catalysts were characterized by inductively coupled plasma-atom emission spectrometry, temperature programmed reduction, and scanning transmission electron microscopy. The catalytic activity for CO oxidation was measured using a flow reactor under atmospheric pressure. Catalytic activity was found to be strongly dependent on the reduction property of oxygen adsorbed on the gold surface, which related to gold particle size. Higher catalytic activity was found when the gold particles had an average diameter of 3–5 nm; in this range, gold catalysts were more active than the Pt/ZnO/Al₂O₃ catalyst in CO oxidation. Au/ZnO/Al₂O₃ catalyst with small amount of ZnO is more active than Au/Al₂O₃ catalyst due to higher dispersion of gold particles.     

Comparative studies of gold catalysts prepared via solvated metal atom impregnation and conventional impregnation: characterization and low-temperature co oxidation

Supported Au catalysts for low-temperature CO oxidation were prepared by solvated metal atom impregnation (SMAI) and conventional impregnation (CI). X-ray photoelectron spectroscopy investigations indicated that gold in all the samples was in the metallic state. TEM and XRD measurements showed that the mean diameter of Au particles prepared by SMAI was smaller than that of those prepared by CI with the same gold content. Catalytic tests showed that SMAI catalysts had higher CO oxidation activity than CI catalysts with the same compositions. Both SMAI and CI Au/TiO₂catalysts exhibited high activities in low temperature CO oxidation. Full CO conversion was obtained at 323 K for 3.1 wt.% Au/TiO₂ (SMAI) catalyst, which displayed higher activity than the 3.1 wt.% Au/D-72(SMAI) and 3.1 wt.% Au/TiO₂(CI). Although the sizes of gold particles prepared by the same method and supported on both TiO₂ and resin were comparable, the Au/TiO₂ catalysts showed significantly higher activities than the Au/resin catalysts with the same Au contents under the same reaction conditions. These results prove that not only the gold particle size, but also the support plays a key role in CO oxidation. This revised version was published online in June 2006 with corrections to the Cover Date.     

焙烧温度对Au/Fe2O3选择性氧化富氢气体中CO催化性能的影响

甲醇重整在线制氢作为质子交换膜燃料电池的燃料成为当前研究的热点。受重整反应动力学及热力学的限制，使得甲醇重整气(富氢气体)中除含有大量的氢气外还含有少量的CO，CO极易吸附在燃料电池阳极催化剂表面，使电池性能下降，因而必须去除重整气中的CO，选择性氧化脱除富氢气     

纳米Au/TS-1催化剂的制备及用于甲醇羰基化体系

采用负压沉积沉淀法、等体积浸渍法、负压等体积浸渍法等方法制备了纳米Au/TS-1催化剂,研究了深床焙烧和等离子体焙烧,以及焙烧温度和焙烧气氛对催化剂中纳米金粒子大小和催化性能的影响,并采用ICP、TEM、XRD、UV-vis、XPS对催化剂金粒子进行了物化性能表征,采用甲醇羰基化制乙酸甲酯反应表征催化性能.结果表明,不同制备方法、不同焙烧方法、不同焙烧温度和焙烧气氛对负载型纳米Au/TS-1沸石分子筛催化剂中金粒子的大小、形貌、物化性质和催化性能有明显影响.其中,3种制备方法中,氢气气氛下焙烧均比空气和氮气气氛下焙烧得到的催化剂的金粒子尺寸更小,分散更均匀,约为5~10 nm.与其它方法相比,负压沉积沉淀法可制得分散更均匀的金粒子,Au/TS-1沸石催化剂中的金粒子尺寸更小,平均粒径为1~5 nm.催化性能评价结果显示,3种方法制备出的负载型金催化剂用于催化甲醇羰基化制乙酸甲酯反应体系中,甲醇的转化率分别为85%、75%、60%,乙酸甲酯选择性可高达68%,反应温度200℃为最好.     

Support effect in high activity gold catalysts for CO oxidation

In this work, we present a detailed study concerning the evaluation of the metal-support interaction in high activity gold catalysts for CO oxidation. Using the colloidal deposition method, model catalysts were prepared, which allow the isolation of the effect of the support on the catalytic activity. Prefabricated gold particles were thus deposited on different support materials. Since the deposition process did not change the particle sizes of the gold particles, only the influence of the support could be studied. TiO2, Al2O3, ZrO2, and ZnO were used as support materials. Catalytic tests and high resolution transmission electron microscopy clearly show that the support contributes to the activity. However, our results are not in line with the distinction between active and passive supports based on the semiconducting properties of the oxidic material. The most active catalysts were obtained with TiO2 and Al2O3, while ZnO and ZrO2 gave substantially less active catalysts. Furthermore, the effect of other important parameters on the catalytic activity (i.e., particles size distribution, calcination temperature, and aging time for a Au/TiO2 catalyst) has also been studied. Using this preparation route, the catalysts show high-temperature stability, size dependent activity, and a very good long-term stability.     

Promoting Effects of Iron on CO Oxidation over Au/TiO2 Supported Au Nanoparticles

Fe-doped TiO₂ supported gold nanoparticles as high-performance CO oxidation catalysts were prepared. XRD data revealed that TiO₂ support was in an anatase phase. After calcination at 300℃, the sample showed nanotube structure, and the size of gold nanoparticles was 3.1 nm. When calcined at 500℃, most nanotubes broke, and gold nanoparticles grew up to 5.9 nm. XPS spectrum indicated the presence of Fe in the +3 oxidation state. Au/Fe-TiO₂(Au:1.44%, Fe:1.35%) calcined at 300℃ possessed the best catalytic activity, and it could completely convert CO at 25℃. The temperature of 100% CO conversion(T_100%) of Fe-free catalyst was 40℃. After the catalysts were stored at room temperature for 7 d, T_100% of Au/Fe-TiO₂ increased from 25℃ to 30℃, while T_100% of Fe-free catalyst increased from 40℃ to 80℃. The catalytic activity and storage stability of Au/TiO₂ could be improved by Fe-doping. The increase of specific surface area, generation of oxygen vacancies and new adsorption sites, depression of the growth of gold nanoparticles, and strong metal-support interaction were responsible for the promoting effect of iron on the catalytic performance of Au/TiO₂ for CO oxidation.     

Influence of pretreatment conditions on low-temperature CO oxidation over Au/MOx/Al2O3 catalysts

Composite oxide MO_x/Al₂O₃ supported gold catalysts for low-temperature CO oxidation were prepared and investigated. The presence of transition metal oxide was proved to be beneficial to the improvement of catalytic performance of Au/Al₂O₃ catalysts for low-temperature CO oxidation. Furthermore, the influence of various pretreatment conditions on Au/MO_x/Al₂O₃ catalysts was studied carefully. The image of TEM showed that gold catalyst with small gold particles only in the form of a fine dispersion exhibited highly catalytic activity. The XPS, Fourier transform infrared (FTIR) spectroscopy characterization results of Au/FeO_x/Al₂O₃ catalyst showed that gold catalysts having partially oxidized gold species have the best catalytic performance. One possible pathway for CO oxidation on Au/FeO_x/Al₂O₃ catalyst is that the CO adsorbed on gold particles reacts with adsorbed oxygen, which is possible to occur on oxygen vacancies on the support or at the metal–support interface.