新型疏水性酶载体的合成及其性能研究

研究了聚丙烯酸酯类疏水性固定化酶载体(包括环氧基和胺基)的合成,旨在提高载体固载酶的性能。结果表明,所得载体的孔结构适合固定化青霉素酰化酶、D-氨基酸氧化酶、DL-7-ACA酰化酶、头孢菌素C酰化酶等。固定化D-氨基酸氧化酶的酶活与载体的含水量(与其孔结构相关)有密切的关系;载体的突出优点是固载酶时,酶的固定化效率可高达50%。     

固定化青霉素酰化酶新型载体PEI/SiO2的制备及其特性

通过γ-氯丙基三甲氧基硅烷的媒介, 将聚乙烯亚胺(PEI)化学偶联在硅胶微粒表面, 制备了固定化青霉素酰化酶的新型复合载体PEI/SiO2, 最终制得了活性高且稳定性好的固定化青霉素酰化酶. 通过测定复合载体表面PEI的偶合量, 考察了各种反应条件对复合载体制备的影响规律; 通过红外光谱与电导滴定法测定, 对复合载体表面的化学结构与组成进行了表征; 为探索复合载体PEI/SiO2固定化酶的作用机理, 测定了复合载体在固定化酶前的ζ电位. 研究结果表明, 通过氯丙基硅烷偶联剂的媒介, 聚胺大分子PEI可以充分地被化学偶联在SiO2表面, 键合量可达到15%. 偶联反应的适宜条件: 反应温度90-94 ℃; 反应时间5h; PEI的质量浓度0.45-0.50 g/mL. 由于PEI分子链中含有大量氨基, 少量的共价键联与大量的物理吸附相结合, 既可使青霉素酰化酶被快速稳定地固定化, 又能很好地保持酶的构象, 使其具有较高的催化活性与活力回收率, 而且具有良好的连续操作稳定性, 重复使用15次, 固定化酶的活性可稳定地保持在初活性的87.5%水平上.     

青霉素酰化酶在介孔分子筛MCM-41上的固定化研究

通过改变酶固定化时的pH值、温度、时间以及酶用量,研究了固定化条件对MCM-41载体上固定化青霉素酰化酶的酶活及其稳定性的影响,明确了酶活及其稳定性随固定化条件的变化规律,初步分析了青霉素酰化酶在介孔分子筛MCM-41上的固定化过程。     

聚丙烯酸载体用于青霉素酰化酶的固定

以反应性单体丙烯酸和交联剂二乙烯基苯,以石油醚为致孔剂,通过悬浮聚合制备固定化酶的载体,并用于对青霉素酰化酶的固定。研究了丙烯酸与二乙烯基苯以不同摩尔比对青霉素酰化酶固定活性的影响,以及悬浮聚合时水油相比例的不同所合成的载体对固定化酶性能的影响。当丙烯酸和二乙烯基苯摩尔比为84.2:4时合成的载体固定青霉素酰化酶的酶活为2784U/g,而水油相比为2.75:1（丙烯酸和二乙烯基苯摩洋比为84.2:5）时固定青霉素酰化酶活达到2183U/g。固定青霉素酰化酶可使青霉素转化,得到半合成青霉素的中间体6-氨基青霉烷酸,由此可制成高效、广谱、服用方便的新青霉素。     

乙烯基Ia3d介孔硅分子筛的环氧化及其固定化青霉素酰化酶(英文)

采用直接共聚法合成表面含有乙烯基的具有立方相Ia3d结构的介孔硅分子筛(V-ClMS),然后对乙烯基团进行环氧化制备得到表面环氧基功能化的介孔硅分子筛(E-CIMS),采用X射线衍射、N2吸附-脱附、透射电镜、热重分析和13C固体核磁共振对制备的介孔硅分子筛进行了表征.结果表明,表面含有乙烯基的V-ClMS介孔硅分子筛能被一步成功合成,并易于发生环氧化而获得表面环氧基功能化的E-CIMS介孔硅分子筛.将E-CIMS介孔硅分子筛作为载体用于固定化青霉素G酰化酶(PGA),研究了表面环氧基团对固定化PGA初活性和操作稳定性的影响.结果表明,随着表面环氧基团数量的增加,介孔硅分子筛孔径减小,表面疏水性增加,导致载酶量和初活性减小.但介孔硅分子筛表面适量的环氧基团能增强E-CIMS介孔硅分子筛与PGA之间的相互作用,从而提高固定化PGA的操作稳定性.     

含氨基和环氧基双功能基的聚合物刷磁性微球的制备及对青霉素G酰化酶的固定化

在内部分散超顺磁性Fe3O4纳米粒子的二乙烯苯交联聚丙烯酸微球表面引入原子转移自由基聚合(ATRP)引发剂,引发聚合向微球表面分别引入P(GMMA-r-DMAEMA-r-GMA)、P(GMMA-r-DMAEMA)和P(GMMA-r-GMA)无规共聚物刷(GMMA为甲基丙烯酸甘油单酯,DMAEMA为甲基丙烯酸-N,N-二甲氨基乙酯,GMA为甲基丙烯酸缩水甘油酯),聚合物刷中GMMA链节的作用是使聚合物刷具有亲水性,DMAEMA引入氨基,GMA引入环氧基.研究了青霉素G酰化酶在这些载体上的固定化和其酶活性.结果表明,同时引入环氧基和氨基的P(GMMA-r-DMAEMA-r-GMA)刷磁性微球固定化青霉素G酰化酶的活性和活性收率都最高,其固定化动力学比只含环氧基P(GMMA-r-GMA)刷磁性微球的好.固定化酶比自由酶更耐热,固定化酶的最佳pH值比自由酶的略高,固定化酶重复使用10次后其活性保留70%.     

微波辐射高效共价固定青霉素酰化酶

为提高青霉素酰化酶的共价固定化效率, 在微波辐射条件下将酶蛋白共价固定于介孔泡沫硅(MCFs)的孔道中. 通过正硅酸四乙酯水解缩合制备介孔泡沫硅, 再于微波辅助下将青霉素酰化酶共价固定在其孔道中. 以固定化酶相对活力和活力回收为指标, 考察了加酶量、固定化温度、微波辐射时间等条件对酶固定化效率的影响. 实验结果表明: 当加酶量为60 mg/g, 固定化温度为20 ℃, 微波辐射140 s, 固定化酶相对活力达到178.1%, 表观活力为1191.3 U/g(以湿重计). 与常规方法相比, 微波辅助固定化酶时, 固定化酶相对活力提高34.5%, 固定化时间亦大幅缩短至数分钟, 这为青霉素酰化酶的高效共价固定化提供了一条新的途径.     

青霉素酰化酶在甲基丙烯酸缩水甘油酯共聚物上的固定化

 用共价键合法将青霉素酰化酶固定化在珠状多孔的甲基丙烯酸缩水甘油酯（GM）共聚物上，研究了固定化反应时间、温度、pH值和酶液用量对固定化青霉素酰化酶的表观活性、表观偶联效率、活性回收及稳定性的影响．将GM共聚物载体加入到磷酸缓冲液（0．1mol／L，pH10．8）与青霉素酰化酶液（每克干载体用酶液1ml）的混合溶液中，在30℃下反应72h，单位质量（干重）固定化酶的表观活性为348U／g，表观偶联效率为66．7％，活性回收为31．7％．     

固相PGA酶催化一步法合成氨苄西林的工艺研究

采用吸附法将青霉素酰化酶(PGA)固定于AB-8树脂上,通过固相酶催化D-苯甘氨酸甲酯与6-氨基青霉烷酸(6-APA)反应制备氨苄西林,对酰化反应中的最适pH条件、溶剂体系、反应温度、反应时间、底物浓度进行实验研究。以氨苄西林收率和水解比为评价条件,固相酶最适催化pH值为6.5,通过正交实验分析表明,在异丙醇-PBS缓冲体系中,350mg PGA/AB-8(固定化酶活性113U·g~(-1))催化下,反应温度10℃,底物浓度(D-PGME∶6-APA)为3.5∶1,反应时间8h,氨苄西林收率达到71.3%。固相PGA酶重复回用6次,氨苄西林收率由71.3%降至63.6%。     

不同介孔材料固定青霉素酰化酶的稳定性研究

介孔材料由于具有在2～30nm之间可调的纳米级规则孔道、大比表面积和强吸附性能而成为固定化酶的优良载体．将酶固定于介孔材料的孔道中制备成的固定化酶与溶液酶相比,有易于与产物分离,并可回收和反复使用,可降低生产成本,减少酶的自水解和保持酶的活性．青霉素酰化酶（Penicillin acylase,PGA,EC．3．5．1．11）又称为青霉素酰胺酶或青霉素氨基水解酶,该酶属于球蛋白,分子量较大,由2个亚基组成：分子量为19500的含有侧链结合位点的亚基和分子量为60000的含有催化位点的亚基．     

Immobilized penicillin G acylase as reactor and chiral selector in liquid chromatography

In this paper, the use of penicillin G acylase (PGA) as a biocatalyst and as a chiral selector is described. Penicillin G-acylase is an interesting enzyme used in the manufacture of semisynthetic antibiotics and, in particular, in the production of 6-APA by hydrolysis of penicillin G. Five PGA-based HPLC columns have been prepared by using two different silica supports by employing two immobilization methods, namely "in situ" and "in batch". The effects of the immobilization techniques and of different silica pore size on the catalytic properties of the enzyme as well as the applicability of the PGA-bonded stationary phases as chiral selectors for a number of chiral drugs have been investigated. The HPLC columns based on immobilized PGA combine the hydrolytic activity and the chiral recognition properties of PGA, therefore they have been used for the development of a combined reaction-separation system for chiral and achiral substrates.     

介孔材料MCFs的合成及组装青霉素酰化酶的性质研究

介孔材料由于具有纳米级规则孔道和巨大的比表面积而在催化、吸附及分离等方面存在较大的应用价值．近年来,由介孔分子筛如MCM-41和SBA-15州等组装功能性材料已成为研究的热点．酶作为高效催化剂有许多优点,但在溶液中易失活,使用后无法回收,有的酶在溶液中还存在自水解问题：将酶组装在介孔材料中制成固定化酶则可解决上述问题．目前已成功地将辣根过氧化物酶     

Recent progress in the development of immobilized penicillin G acylase for chemical and industrial applications: A mini‐review

Immobilized penicillin G acylase (PGA) as an important industrial catalyst can catalyze penicillin G potassium (PG) to 6‐aminopenicillanic acid (6‐APA). 6‐APA is an important intermediate for semisynthetic penicillin drugs, which occupies a huge market space in the anti‐inflammatory field; as a result, immobilized PGA occupies a huge market space in the pharmaceutical field. However, at present, there are different degrees of defects in the preparation and production process of immobilized PGAs on the market because of the huge demand; therefore, the performance of immobilized PGA and its productivity will bring huge economic benefits to enterprises. Therefore, research on immobilized PGA has always been a focus. This review first introduces the source, classification, structure, and catalytic mechanism of PGA and then studies the development of immobilization methods, immobilized carriers, reaction media, enzyme activity regeneration, and reactors of immobilized PGA in recent years.     

环氧基功能化SBA-15介孔分子筛的制备、表征及其固定化青霉素酰化酶

利用表面嫁接法和乙烯基环氧化法制备了环氧基团功能化介孔分子筛G-SBA-15和O-SBA-15,并对其结构和表面性质进行了表征.结果表明,G-SBA-15和O-SBA-15均具有良好的长程有序结构,二者环氧基团的含量分别为0.78 mmol/g和0.37 mmol/g,在O-SBA-15表面还存在一定数量的乙烯基基团.G-SBA-15和O-SBA-15用于固定青霉素酰化酶(pen ic illin G acylase,PGA),固定化酶PGA/G-SBA-15和PGA/O-SBA-15在37℃时水解青霉素G钾制备6-氨基青霉烷酸(6-APA)的表观活性分别为1075 IU/g和1761 IU/g.PGA/G-SBA-15经4次使用后表观活性趋于稳定,经10次使用后保持其初始活性的83.7%.PGA/O-SBA-15在重复使用中,表观活性出现持续衰减,10次使用后保持其初始活性的51.6%,PGA/G-SBA-15的操作稳定性明显好于PGA/O-SBA-15.     

A Process to Produce Penicillin G Acylase by Surface-Adhesion Fermentation Using <Emphasis Type="Italic">Mucor griseocyanus</Emphasis> to Obtain 6-Aminopenicillanic Acid by Penicillin G Hydrolysis

The production of extracellular and mycelia-associated penicillin G acylase (maPGA) with Mucor griseocyanus H/55.1.1 by surface-adhesion fermentation using Opuntia imbricata, a cactus, as a natural immobilization support was studied. Enzyme activity to form 6-aminopencillanic acid (6-APA) from penicillin G was assayed spectrophotometrically. The penicillin G hydrolysis to 6-APA was evaluated at six different times using PGA samples recovered from the skim milk medium at five different incubation times. Additionally, the effect of varying the penicillin G substrate concentration level on the PGA enzyme activity was also studied. The maximum reaction rate, V _max, and the Michaelis constant, K _M, were determined using the Michaelis–Menten model. The maximum levels for maPGA and extracellular activity were found to be 2,126.50 international unit per liter (IU/l; equal to 997.83 IU/g of support) at 48 h and 755.33 IU/l at 60 h, respectively. Kinetics of biomass production for total biomass showed a maximum growth at 60 h of 3.36 and 2.55 g/l (equal to 0.012 g of biomass per gram of support) for the immobilized M. griseocyanus biomass. The maPGA was employed for the hydrolysis of penicillin G to obtain 6-APA in a batch reactor. The highest quantity of 6-APA obtained was 226.16 mg/l after 40-min reaction. The effect of substrate concentration on maPGA activity was evaluated at different concentrations of penicillin G (0–10 mM). K _M and V _max were determined to be 3.0 × 10⁻³ M and 4.4 × 10⁻³ mM/min, respectively.     

Immobilization of Penicillin G Acylase on Calcined Layered Double Hydroxides

A hydrotalcite-like Mg2 /Al3 layered double hydroxide (LDH) material was prepared by means of amodified coprecipitation method involving a rapid mixing step followed by a separate aging process. LDH calcined at 500℃ , denoted as CLDH, was characterized by XRD, IR and BET surface area measurements.CLDH has a poor crystalline MgO-like structure with a high surface area and porosity. CLDH was used as asupport for the immobilization of penicillin G acylase(PGA). The effect of varying the immobilization conditions, such as pH, contact time and the ratio of enzyme to support, on the activity of the immobilized enzymein the hydrolysis of penicillin G has been studied. It was found that the activity of the immobilized enzyme decreased slightly with decreasing pH and reached a maximum after a contact time of 24 h. The activity of theimmobilized enzyme increased with increasing the ratio of enzyme to support. It was found that the adsorption of PGA inhibited the expected reaction of CLDH with an aqueous medium to regenerate a LDH phase. Itsoriginal activity(36%) after 15 cycles of reuse of the immobilized enzyme was retained, but no further loss in the activity was observed.     

An efficient synthesis of ampicillin on magnetically separable immobilized penicillin G acylase

<正>Penicillin G acylase(PGA) was immobilized on the magnetic hydrophilic polymer microspheres with average pore size of 17.1 nm,specific surface area of 128.2 m~2/g and saturate magnetization of 6.4 emu/g.The 96.7%ampicillin yield with 1.60 of the synthesis/hydrolysis(S/H) ratio from 6-aminopenicillanic acid(6-APA) and D-(-)-alpha-phenylglycine methyl ester(D-PGME) can be achieved using the resultant magnetic biocatalyst in ethylene glycol,where only 82.1%yield with 1.40 of the S/H ratio was obtained using the free PGA under the identical reaction conditions.The immobilized PGA can be separated magnetically and recycled for five times without obvious loss of its catalytic activity.     

Di-functional magnetic nanoflowers: A highly efficient support for immobilizing penicillin G acylase

The novel di-functional magnetic nanoflowers (DMNF) which had both epoxy groups and hydrophilic catechol as well as phthaloquinone groups capable of covalently coupling of penicillin G acylase (PGA) were characterized by scanning electron microscopy, transmission electron microscope (TEM), vibrating sample magnetometer, N₂ adsorption, and so on. The studies showed that DMNF possessed “hierarchical petal” structure of nanosheets had specific saturation magnetization of 39.7 emu/g and average pore diameter of 25.4 nm as well as specific surface area of 17.28 m²/g. For hydrolysis of penicillin G potassium catalyzed by the PGA immobilized on DMNF with enzyme loading of 106 mg/g-support, its apparent activity reached 2,667 U/g, which benefited from the “hierarchical petal” and large pore structure of the magnetic DMNF leading to high enzyme loading and fast diffusion of substrate molecules to the immobilized PGA to reaction. The apparent activity of the immobilized PGA could keep 2,408 U/g (above 90% of its initial activity) after repeating use for 10 cycles. The magnetic immobilized PGA exhibited excellent operational stability due to covalently coupling of the enzyme molecules between the support by covalent interaction of the amino groups of PGA and the reactive groups of epoxy, catechol, and phthaloquinone groups on DMNF. Furthermore, the PGA displayed good acid and alkaline resistance as well as thermal stability by immobilization using DMNF.     

Beaded reactive polymers 3 effect of triacrylates as crosslinkers on the physical properties of glycidyl methacrylate copolymers and immobilization of penicillin G acylase

Various glycidyl methacrylate (GMA) copolymers were synthesized by suspension polymerization, using pentaerythritol triacrylate (PETA), trimethylolpropane triacrylate (TMPTA), and trimethylolpropane trimethacrylate (TRIM) as crosslinking comonomers. These copolymers were evaluated for the immobilization of penicillin G acylase. Broad pore-size distribution that was observed was in the range 5-300 nm. Both surface area and pore volume increased with increase in the mole fraction of crosslinking comonomer (increasing crosslink density). The pore volume of the copolymers was more than doubled by including lauryl alcohol as porogen. Binding of penicillin G acylase (PGA) was quantitative on highly crosslinked copolymers. The expression of bound PGA was better on the relatively more hydrophilic GMA-TMPTA and GMA-PETA copolymer supports compared to the GMA-TRIM copolymers. Among the different copolymers studied, GMA-TMPTA copolymer 7411 exhibited highest activity of immobilized penicillin G acylase (167.4 IU/g) with 35.1% expression.