The oxidation‐treated interface on tribological properties of carbon fibers‐reinforced PTFE composite under oil‐lubricated condition

The effect of air oxidation and ozone surface treatment of carbon fibers (CF) on tribological properties of CF reinforced polytetrafluoroethylene (PTFE) composites under oil‐lubricated condition was investigated. Experimental results revealed that ozone treated CF reinforced PTFE (CF–PTFE) composite had the lowest friction coefficient and wear under various applied loads and sliding speeds compared with untreated and air‐oxidated composites. X‐ray photoelectron spectroscopy (XPS) study of carbon fiber surface showed that, after ozone treatment, oxygen concentration was obviously increased, and the amount of oxygen‐containing groups on CF surfaces was largely increased. The increase in the amount of oxygen‐containing groups enhanced interfacial adhesion between CF and PTFE matrix. With strong interfacial adhesion of the composite, stress could be effectively transmitted to carbon fibers; carbon fibers were strongly bonded with PTFE matrix and large scale rubbing‐off of PTFE was prevented, therefore, the tribological properties of the composite were improved. Copyright © 2009 John Wiley & Sons, Ltd.     

Interfacial studies on the ozone and air‐oxidation‐modified carbon fiber reinforced PEEK composites

In this work, ozone modification method and air‐oxidationwere used for the surface treatment of polyacrylonitrile(PAN)‐based carbon fiber. The surface characteristics of carbon fibers were characterized by XPS. The interfacial properties of carbon fiber‐reinforced (polyetheretherketone) PEEK (CF/PEEK) composites were investigated by means of the single fiber pull‐out tests. As a result, it was found that IFSS (interfacial shear strength) values of the composites with ozone‐treated carbon fiber are increased by 60% compared to that without treatment. XPS results show that ozone treatment increases the amount of carboxyl groups on carbon fiber surface, thus the interfacial adhesion between carbon fiber and PEEK matrix is effectively promoted. The effect of surface treatment of carbon fibers on the tribological properties of CF/PEEKcomposites was comparativelyinvestigated. Experimental results revealed that surface treatment can effectively improve the interfacial adhesion between carbon fiber and PEEK matrix. Thus the wear resistance was significantly improved. Copyright © 2009 John Wiley & Sons, Ltd.     

Effect of carbon fiber surface treatments on the flexural strength and tribological properties of short carbon fiber/polyimide composites

Pitch‐based short carbon fibers (CFs) were treated by air oxidation and cryogenic nitrogen, respectively. Thereafter the treated and untreated CFs were incorporated into polyimide (PI) matrix to form composites. The CFs before and after treatment were examined by XPS and SEM.The flexural strength of the specimen was determined in a three‐point test machine and the tribological properties of PI composites sliding against GCr15 steel rings were evaluated on an M‐2000 model ring‐on‐block test rig. The results show that the surface of the treated CFs became rougher. Lots of active groups formed on the CF surface after air oxidation.The treatment can effectively improve the mechanical and tribological properties in their PI composites due to the enhanced fiber‐matrix interfacial bonding. Copyright © 2008 John Wiley & Sons, Ltd.     

Various ways to strengthen the fiber‐matrix interface for enhanced composite performance

Surface treatment (ST) of carbon fibers (CF) leads to an enhancement in fiber‐matrix adhesion. However, it deteriorates the strength of a fiber which makes its reinforcing action less effective in a composite. These effects in opposite directions control the net strength of a composite, and hence, the treatment has to be judiciously applied, which would enhance the first factor and minimize the second one. Authors have recently reported on four effective techniques (using various doses) such as treatments with nanoparticles of Ytterbium fluoride (YbF₃)_, cold remote nitrogen–oxygen plasma (CRNOP), γ‐ray irradiation and nitric acid oxidation. Amongst these methods, nitric acid oxidation is studied in depth in the literature, and γ‐ray irradiation is sparingly studied. However, nano‐YbF₃ and CRNOP were first time reported in the literature by the authors. However, comparative aspects of all these methods were not addressed. In this paper, these aspects in details are discussed to lay down the right criteria for selection of a ST technique of CF to design the desired performance of a composite. The composites with polyetherimide and treated CF (including untreated) were developed and evaluated for various properties including tribological one. Treated CF based composites exhibited excellent mechanical and tribological properties (under harsh operative conditions with wear rates ≈ 1 × 10^?15 m³/Nm and μ ≈ 0.09). It was concluded that for strength and tribo‐performance, different treatments and doses are to be employed. Overall nanosized‐YbF₃ treatment of CF proved to be the most promising ST method. Copyright © 2013 John Wiley & Sons, Ltd.     

Modification effects of short carbon fibers on mechanical properties and fretting wear behavior of UHMWPE composites

The present work comparatively studied the modification effects of short carbon fiber (CF) on the mechanical properties and fretting wear behavior of ultra‐high molecular weight polyethylene (UHMWPE)/CF composites. The interactions between CFs and UHMWPE interface were also investigated in detail. The results showed that, with the increase in fiber content, the compressive modulus and hardness of the composites increased, while its impact strength decreased. It was found that filling of CF can reduce the friction and wear of UHMWPE. In addition, the UHMWPE‐based composites reinforced with nitric acid‐treated CF exhibited better mechanical properties, lower friction coefficient, and higher wear resistance than those of untreated UHMWPE/CF composites. This was attributed to the improvement of interfacial adhesion and compatibility between CF and UHMWPE matrix caused by surface chemical modification of CF. Copyright © 2015 John Wiley & Sons, Ltd.     

Friction and wear properties of combined surface modified carbon fabric reinforced phenolic composites

Carbon fabric (CF) was surface treated with silane-coupling agent modification, HNO₃ oxidation, combined surface treatment, respectively. The friction and wear properties of the carbon fabric reinforced phenolic composites (CFP), sliding against GCr15 steel rings, were investigated on an M-2000 model ring-on-block test rig. Experimental results revealed that combined surface treatment largely reduced the friction and wear of the CFP composites. Scanning electron microscope (SEM) investigation of the worn surfaces of the CFP composites showed that combined surface modified CFP composite had the strongest interfacial adhesion and the smoothest worn surface under given load and sliding rate. SEM and X-ray photoelectron spectroscopy (XPS) study of carbon fiber surface showed that the fiber surface became rougher and the oxygen concentration increased greatly after combined surface treatment, which improved the adhesion between the fiber and the phenolic resin matrix and hence to improve the friction-reduction and anti-wear properties of the CFP composite.     

Effect of carbon fiber surface functionality on the moisture absorption behavior of carbon fiber/epoxy resin composites

Polyacrylonitrile (PAN)‐based carbon fibers were electrochemically oxidized in aqueous ammonium bicarbonate with increasing current density. The electrochemical treatment led to significant changes of surface physical properties and chemical structures. The oxidized fibers showed much cleaner surfaces and increased levels of oxygen functionalities. However, it was found that there was no correlation between surface roughness and the fiber/resin bond strength, i.e. mechanical interlocking did not play a major role in fiber/resin adhesion. Increases in surface chemical functionality resulted in improved fiber/resin bonding and increased interlaminar shear strength (ILSS) of carbon fiber reinforced epoxy composites. The relationship between fiber surface functionality and the hydrothermal aging behavior of carbon fiber/epoxy composites was investigated. The existence of free volume resulted from poor wetting of carbon fibers by the epoxy matrix and the interfacial chemical structure were the governing factors in the moisture absorption process of carbon fiber/epoxy composites. Copyright © 2016 John Wiley & Sons, Ltd.     

Surface modification of carbon fiber for improving the interfacial adhesion between carbon fiber and polymer matrix

In this study, the reinforcing mechanism of amine functionalized on carbon fibers (CFs) has been precisely discussed, and the differences between aliphatic and aromatic compounds have been illustrated. Polyacrylonitrile‐based CFs were functionalized with ethylenediamine, 4,4‐diaminodiphenyl sulphone, and p‐aminobenzoic acid (PAB), and CF‐reinforced epoxy composites were prepared. The structural and surface characteristics of the functionalized CFs were investigated using X‐ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FT‐IR), and scanning electron microscopy (SEM). Mechanical properties in terms of tensile and flexural strengths and moduli were studied. The FT‐IR results confirm the success in bonding amines on the CF surface. After treatment of CFs, the oxygen and nitrogen contents as well as the N/C ratio showed an increase. XPS results provided evidence of the chemical reaction during functionalization, rather than being physically coated on the CF surface. Chemical modification of CF with diamines led to considerable enhancement in compatibility of CF filaments and epoxy resin, and remarkable improvements were seen in both tensile and flexural properties of the reinforced composites. SEM micrographs also confirmed the improvement of interface adhesion between the modified CFs and epoxy matrix. Finally, it can be concluded that PAB is a promising candidate to functionalize CF in order to improve interfacial properties of CF/epoxy composites. Copyright © 2015 John Wiley & Sons, Ltd.     

Mechanical properties of rigid polyurethane composites reinforced with surface treated ultrahigh molecular weight polyethylene fibers

The mechanical properties of ultrahigh molecular weight polyethylene (UHMWPE) fibers reinforced rigid polyurethane (PU) composites were studied, and the effects of the fiber surface treatment and the mass fraction were discussed. Chromic acid was used to treat the UHMWPE fibers, and polyurethane composites were prepared with 0.1 to 0.6 wt% as‐received and treated UHMWPE fibers. Attenuated total reflection Fourier transform infrared demonstrated that oxygen‐containing functional groups were efficiently grafted to the fiber surface. The mechanical performance tests of the UHMWPE fibers/PU composites were conducted, and the results revealed that the treated UHMWPE fibers/PU composites had better tensile, compression, and bending properties than as‐received UHMWPE fibers/PU composites. Thermal gravimetric analyzer showed that the thermal stability of the treated fiber composites were improved. The interface bonding of PU composites were investigated by scanning electron microscopy and dynamic mechanical analysis, and the results indicated that the surface modification of UHMWPE fiber could improve the interaction between fiber and PU, which played a positive role in mechanical properties of composites.     

Flexural properties of fiber‐reinforced polypropylene composites with and without a transcrystalline layer

The flexural properties of isotactic polypropylene (PP) matrix composites reinforced with 5–30 vol% of unidirectional pitch‐based carbon, polyacrylonitrile (PAN)‐based carbon, e‐glass or aramid fibers were measured using both static and dynamic test methods. Previous research has shown that these pitch‐based carbon and aramid fibers are capable of densely nucleating PP crystals at the fiber surface, leading to the growth of an oriented interphase termed a “transcrystalline layer” (TCL), while the e‐glass and PAN‐based carbon fibers show no nucleating ability. The PP matrices examined included unmodified homopolymers, nucleated homopolymers and PP grafted with maleic anhydride (MA). The composites based on the unmodified PP homopolymers all exhibited poor fiber/matrix adhesion, regardless of fiber type and presence or absence of a TCL. The addition of nucleating agent to the PP matrix had no measurable effect on either the amount of TCL material in pitch‐based carbon‐fiber‐reinforced composites, as measured by wide‐angle X‐ray scattering, WAXS, or the static flexural properties of the composites reinforced with either type of carbon fiber. However, MA grafting reduced the transcrystalline fraction of the matrix in pitch‐based carbon‐fiber‐reinforced composites; at the highest level of MA grafting, the TCL was completely suppressed. In addition, high levels of MA grafting improved the transverse flexural modulus of the composites containing both types of carbon fibers, and reduced the extent of fiber pull‐out, indicating an improvement in fiber/matrix adhesion. Copyright © 1999 John Wiley & Sons, Ltd.     

Surface modification of carbon fiber via electron‐beam irradiation grafting

In this paper, the surface properties of polyacrylonitrile‐based carbon fibers is improved by electron‐beam (EB) irradiation in maleic anhydride/acetone solution at 100, 150, 200 and 150 KGy. Experimental study of this paper is carried out to identify surface topography, surface chemical composition and functional groups, adsorption ability and interface properties of CF/epoxy composites. The results reveal that the roughness of carbon fiber surface is increased obviously after modification by EB irradiation grafting technology. The ratio value of O/C and the relative content of oxygen functional groups on fiber surface are improved effectively, comparing with the unmodified carbon fiber. Besides, adsorption of carbon fiber on epoxy and the mechanical performance of CF/epoxy composites are clearly enhanced after irradiation grafting modification. Copyright © 2012 John Wiley & Sons, Ltd.     

The addition of acid treated carbon nanotube on the interfacial adhesion of carbon fiber reinforced UHMWPE composite

Carbon fiber reinforced Ultra High Molecular Weight Polyethylene (CF/UHMWPE) composites have been filled with acid treated carbon nanotube to enhance the adhesion. According to the modification, the interlaminar shear strength (ILSS) of composites has been greatly improved. Dynamic wetting method, XPS and SEM are used to examine the microscopic properties of resultant composites. The enhanced ILSS is attributed to the CNT interlock, which improves the wetting between carbon fibers and resins. Copyright © 2017 John Wiley & Sons, Ltd.     

Influence of surface properties of graphene oxide/carbon fiber hybrid fiber by oxidative treatments combined with electrophoretic deposition

An effective way to prepare graphene oxide/carbon fiber hybrid fiber was proposed by the treatment with hydrogen peroxide and concentrated nitric acid combined with electrophoretic deposition process. Surface functional group, surface roughness, and surface morphologies of carbon fibers were examined by Fourier transform infrared spectrometer, atomic force microscopy, and scanning electron microscopy. Results showed that a uniform and thick graphene oxide films were constructed on the surface of carbon fiber. Deposition density increased by introduction of pretreatment of the carbon fiber in the electrophoretic deposition process has been shown as a possible method. Dynamic contact angle analysis results indicated that the deposition of graphene oxide significantly improved surface free energy of carbon fiber by increasing surface area and polar groups. The introduction of graphene oxide in the carbon fiber‐reinforced epoxy composites results in a 55.6% enhancement in the interfacial shear strength and confirms the remarkable improvement in the interfacial adhesion strength of the composites, and the fracture mechanism was also analyzed. Copyright © 2016 John Wiley & Sons, Ltd.     

Probing the tribological behaviors in water of novel poly(phthalazione ether sulfone ketone) and its composites based on the state of aggregation and the microstructure

In this paper, novel poly(phthalazione ether sulfone ketone) (PPESK) and its composites reinforced with carbon fibers (CFs) were prepared, and their tribological behaviors in pure and sea water were comparatively investigated. Affected by the noncoplanar twisted aromatic structure in the molecular skeleton, the aggregation of the macromolecular chain in PPESK was amorphous, resulting in very high water absorption of PPESK matrix. The invading water molecules led to a sharp decrease in the hardness of PPESK surface, resulting in very high wear rate of PPESK in water. Although CF/PPESK composites had higher water absorption than pure PPESK, their wear processes in water were no longer dominated by high water absorption but by the load‐carrying effect of CFs, ascribed to the good CF/PPESK interfacial adhesion. Therefore, CF/PPESK composites exhibited very low wear rates in the order of 10^?7 mm³/Nm in water, which decreased with the CF content increasing until the content of CFs reached 50%. The results revealed that the most critical factor determining the wear behavior of a fiber‐reinforced polymer composite sliding in water is the fiber/matrix interface but not the water absorption of the polymer matrix. Copyright © 2017 John Wiley & Sons, Ltd.     

The interfacial feature of thermoplastic polystyrene composite filled with nitric acid oxidized carbon fiber

The quality of interfacial interaction is dictated by the surface chemistry of the carbon fibers and the composition of the matrix. The composition of polystyrene was modified by the addition of maleic anhydride (MAH) grafted polystyrene. The surface properties of the various matrix formulations were characterized by contact angle. Carbon fibers were modified by oxidation in nitric acid. The surface composition of the carbon fibers was characterized. The interaction between modified polystyrene and the carbon fibers was studied by single fiber pull‐out tests. The best adhesion behavior was achieved between polystyrene containing grafted MAH and nitric acid oxidation carbon fibers. The addition of MAH‐grafted polystyrene to the unmodified polystyrene caused the interfacial shear strength (IFSS) to increase. The IFSS of this fiber‐matrix combination allowed for the full utilization of the tensile strength of polystyrene. Copyright © 2009 John Wiley & Sons, Ltd.     

Mechanical properties of plasma‐treated carbon fiber reinforced PTFE composites with CNT

This paper is concerned with the effects of the plasma surface treatment and the addition of CNT on the mechanical properties of carbon fiber/polytetrafluoroethylene (PTFE) composite. The tensile and flexural strength of composites containing CNT and plasma‐treated carbon fibers improved. The flexural strength first decreases with respect to the CF content. The flexural strength increases to 179 MPa for the plasma‐treated composite as compared with 167 MPa for the neat carbon fiber composites. The overall improvement is thus nearly 8%.     

Improved interfacial properties of PI composites through graphene oxide and carbon nanotubes on carbon fiber surface

Carbon nanotubes (CNTs) have been identified as excellent nanoreinforcements for carbon fiber (CF)–reinforced polymers regarding a wide range of engineering applications. The outstanding properties of CNTs, such as their large surface area, high mechanical strength, and low manufacturing cost bring them to be distinguished nanoreinforcements for carbon fiber–reinforced polymers to form multifunctional and multiscale composites. Electrophoretic deposition of graphene oxide for CNTs onto the CF surface was conducted. The presence of graphene oxide–CNTs may effectively increase both the roughness and wettability of the CF surface, resulting in an improvement to the interfacial bonding strength between the CF and the polyimide (PI).     

Improving the interfacial property of carbon fiber/PI resin composite by grafting modification of carbon fiber surface

The poor interfacial adhesion between carbon fibers (CFs) and polyimide (PI) resin has seriously hampered the application of CF/PI composites. In this work, the interfacial adhesion was efficiently enhanced by grafting on the CF surface. Surface morphology and surface composition of modified carbon fibers were characterized, which indicated that acrylamide was grafted successfully on the CF surface and the surface roughness was increased slightly. After grafting, the interface shear strength of modified carbon fibers/PI composites was significantly improved by 86.96%, and the interlaminar shear strength was enhanced by 55.61% due to the covalent bonds in interphase and the toughening effect of sizing agent. Moreover, the mechanical properties of composites with different interfacial adhesion were measured, which further confirmed the effect of the grafting modification.     

Preparation of Oxidized Organosolv Lignin⁃based Hydrophilic Sizing Agent and Its Application in Polypropylene北大核心CSCD

The interfacial compatibility of carbon fiber （CF） reinforced composites is the key factor to determine the comprehensive properties of the composites. The sizing agent plays an indispensable role between carbon fibers and matrix resins. Environmentally friendly hydrophilic sizing agent is is a hot research issue to be solved. In this work,the hydrophilic lignin-based sizing agent and carbon fiber reinforced polypropylene （PP） composites are prepared and studied. The lignin is ozonized to increase the reactive group. The obtained lignin reacts with epoxy group to prepare the oxidized organic solvent lignin based epoxy resin（OLBE）. OLBE reacts with alcohol amine and carboxylic acid to obtain the hydrophilic lignin-based sizing agent. KH550 is further added to balance the hygroscopicity of sizing agent. Finally,an oxidized organic solvent lignin-based hydrophilic sizing agent（OLBEDK）with excellent stability was prepared. The CF treated with 2. 5% solid content OLBEDK was only 3. 0 mg. The ILSS,Flexural strength,Flexural modulus and Impact strength of CF/PP composites are increased by 50. 8%,34. 2%,53. 7% and 127. 8%, respectively,compared with those of CF/PP composites without sizing. This is attributed to the π-π conjugation between the benzene ring of lignin and the carbon six-membered ring of CF,and the physical entanglement between the alkyl chain of KH550 and the molecular chain of PP,which enhances the interfacial interaction between CF and PP effectively. © 2022, Science Press (China). All rights reserved.     

Effect of treatment on the thermal conductivity and thermal diffusivity of oil‐palm‐fiber‐reinforced phenolformaldehyde composites

The thermal conductivity and thermal diffusivity of oil‐palm‐fiber‐reinforced untreated (Sample 1) and differently treated composites were measured with the transient plane source technique at room temperature and under normal pressure. All the composites were 40% oil‐palm fiber by weight. The fibers were treated with alkali (Composite 2), silane (Composite 3), and acetic acid (Composite 4) and reinforced in a phenolformaldehyde matrix. The thermal conductivity and thermal diffusivity of the composites increased after treatment to different extents. The thermal conductivity of the treated fibers as well as of the untreated fibers was calculated theoretically. The model results show that the thermal conductivity of the untreated fiber was smaller than the thermal conductivity of the treated fibers. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 916–921, 2000