ZrO2在合成甲醇催化剂CuO-ZnO-ZrO2中的作用

采用并流共沉淀法制备了一系列ZrO2的原子比不同的CuO-ZnO-ZrO2甲醇合成催化剂.在固定床反应器中进行合成气制甲醇的研究,考察了ZrO2在催化剂中的作用.结果表明,ZrO2的加入能显著提高催化剂的性能,当ZrO2的原子比达到0.10时,催化剂的活性最高并且耐热性能最强;过量的ZrO2会降低催化剂的活性.利用TPR、XRD、BET技术对催化剂进行了表征,发现适量ZrO2的加入不仅有助于提高Cu活性组分在催化剂表面的分散,提高催化剂的比表面积,使催化剂不容易高温烧结,而且有利于促进催化剂还原.     

二氧化碳加氢直接合成二甲醚催化剂的研究 Ⅱ 铜/锌对复合催化剂结构和性能的影响

制备了具有不同铜/锌(氧化物质量比)的CuO-ZnO-Al2O3/HZSM-5复合型催化剂，考察了其对CO2加氢直接合成二甲醚的催化性能，并采用H2-TPR、XRD、BET、IR及XPS等表征方法对催化剂的物化性质进行了表征。结果表明，催化剂中的铜/锌对催化剂的反应性能、晶相结构以及还原难易程度等均有一定程度的影响。在所制备的四种不同铜/锌的复合催化剂中，以Cu/Zn＝1/2的催化剂反应性能最为理想，虽然它们的还原峰位置和比表面积相差不大，但在反映催化剂各组分间相互作用的IR谱图中则表现出较明显的差别。XPS结果表明，活性组分铜以Cu+和Cu0两种形态存在，支持Cu+和Cu0共同组成合成甲醇活性中心的观点。     

CuO的添加方式对合成二甲醚反应中脱水性能的影响

CuO以不同的添加方式对-γA l2O3进行改性.用H2-TPR、还原态NH3-TPD、XRD表征技术以及浆态床CO H2合成二甲醚反应对催化剂的还原性能、还原态的酸中心分布、物相分布和反应活性进行了考察.H2-TPR结果表明,在沉积法制备的催化剂上可还原的氧化铜的量最大,且容易还原;还原态NH3-TPD结果说明了沉积法制备的催化剂上适合脱水反应进行的弱酸中心的比例最大;XRD结果发现在浸渍法制备的催化剂上,有少量的铜和铜铝化合物存在,其它方法制备的催化剂上CuO均匀分散在催化剂表面;目标反应的结果指出了沉积法制备的催化剂上,二甲醚的选择性最佳.     

CeO_2改性Cu/Zn-Al水滑石衍生催化剂对甲醇水蒸气重整制氢性能的影响

采用原位合成法在γ-Al2O3表面合成了锌铝水滑石,再采用顺次浸渍法制备了Ce/Cu/Zn-Al催化材料;将其应用于甲醇水蒸气重整制氢,探讨了Ce含量对Cu/Zn-Al催化剂催化性能的影响.催化剂表征结果表明,CeO_2的引入改善了活性组分铜的分散度、铜的比表面积以及催化剂的氧化还原性质,进而提高了催化剂的催化活性和产氢率.当Ce含量为4%时,催化剂活性最佳,在250℃时,甲醇转化率达到100%,CO摩尔分数为0.39%,与Cu/Zn-Al催化剂相比,甲醇转化率提高了近40%.     

CuO/Ce0.5Zr0.5O2的结构特征及催化性能表征

以硝酸铈和硝酸锆为原料,采用共沉淀法制备了不同摩尔比(X=0,0.1,0～1.0)的CexZr1-xO2样品.并以Ce0.5Zr0.5O2为载体,采用浸渍法负载不同含量的CuO,用色谱流动法考察其对CO的氧化活性.并用XRD,TPR和BET等技术对CuO/Ce0.5Zr0.5O2各样品进行了表征,结果表明,当CuO负载量为10.0%时,催化剂CO的氧化活性最高;XRD测定表明催化剂氧化活性的高低与铜物种在Ce0.5Zr0.5O2上的分散状态有关;TPR结果亦显示活性的高低与Ce0.5Zr0.5O2上分散较好的铜物种的α还原峰及分散较差的γ还原峰的峰温及形状有关.     

交替微波加热法对制备氧还原催化剂性能的影响

详细研究了交替微波加热法制备多壁碳纳米管负载Pt催化剂(Pt/MWCNTs)的过程中交替微波加热(5s-on/5s-off)次数对催化剂性能的影响.X射线粉末衍射(XRD)结果表明,Pt的晶粒尺寸在开始的加热阶段基本上没有发生变化,但是随着加热次数的增多,Pt的晶粒尺寸逐步增大.采用循环伏安法和旋转圆盘电极技术考察了催化剂的电化学活性.结果显示,以5s-on/5s-off加热20次时,催化剂显示出最佳的催化活性;在0.5mol· L-1 H2SO4饱和氧水溶液中催化剂的氧还原起峰电位接近1.0 V(vs RHE).交替微波加热法简单经济,在大批量制备催化剂等纳米材料方面显示出较好的应用前景.     

pH值对共沉淀法制备钼基多金属氧化物催化异丁烯选择氧化制甲基丙烯醛性能的影响

研究了共沉淀法制备Mo-Bi-Fe-Co-Mn 五组分催化剂过程中溶液的pH值对催化剂中物种存在状态的影响. 并考察其异丁烯选择氧化制备甲基丙烯醛(MAL)的反应性能. 结合粉末X射线衍射(XRD)、傅里叶变换红外(FTIR)光谱、X射线光电子能谱(XPS)、氮气吸附-脱附和H₂程序升温还原(H₂-TPR)等表征手段对催化剂的结构进行了详细的研究. 结果表明, 溶液的pH值对催化剂结构和组成有明显的影响. 催化剂中某种特定物相MX随沉淀的pH值的提高而增加, 当pH=7时,催化剂中MX相的量达最大值. 此时,异丁烯的转化率和甲基丙烯醛的选择性分别为99.9%和95.6%. 进一步提高沉淀的pH值, 催化剂中MX相的量减少, 异丁烯的转化率和甲基丙烯醛的选择性也相应降低. 研究表明,催化剂上各组分间存在一定的相互作用, 催化剂中的特定物相MX是影响反应活性的关键因素之一.     

Pt/CNTs催化剂的制备及其催化臭氧化活性研究

以碳纳米管(CNTs)为催化剂载体, 以H₂PtCl₆•6H₂O为贵金属活性组分前驱物, 采用等体积浸渍法制备了Pt/CNTs催化剂. 以草酸为目标污染物, 考察了所制备催化剂的催化活性, 并采用SEM, XRD和XPS等分析方法对催化剂进行表征. 对活性组分Pt的负载量、氢还原温度和热处理方式进行了研究, 确定了适宜的制备条件为Pt负载量1.0%、氢还原温度350 ℃. 研究表明, 在本实验条件下, 单独臭氧氧化、碳纳米管载体催化臭氧化和Pt/CNTs催化臭氧化分别能去除溶液中3.0%, 72.9%和97.9%的草酸. Pt的负载明显地提高碳纳米管催化臭氧化的效果. XRD分析显示催化剂的活性组分Pt以单质Pt⁰的形式存在; 与氢还原过程相比, 在空气气氛中焙烧制备的Pt/CNTs催化剂表面Pt的结晶度过高, 而且XPS结果表明此催化剂表面的Pt有化学吸附氧存在, 导致催化活性降低.     

制备因素对Ni/C催化剂上乙醇气相羰基化反应性能的影响

采用等体积浸渍法制备负载型Ni/C催化剂,考察了制备因素对乙醇直接气相羰基化反应的影响。实验结果表明,催化剂最佳制备因素为,Ni的质量分数为5%,活性炭采用水洗预处理,控制浸渍液的pH值为8.0～9.0,焙烧温度为450℃,H₂还原温度为400℃。采用上述参数制备的Ni/C催化剂,其乙醇转化率和丙酸选择性分别为96.14%和95.71%。利用N₂物理吸附法研究载体预处理对催化剂比表面积、孔容及孔径的影响和X射线衍射法(XRD)研究了活性组分在惰性气氛中焙烧时的分散状况。     

燃料电池用Cu-Ce(La)Ox变换催化剂的制备及性能

采用共沉淀法、沉积沉淀法和超均匀沉淀法制备了30%Cu-Ce-La(10%)Ox型变换催化剂,利用活性测试、XRD和原子吸收等对催化剂的催化性能、晶相结构及组成进行了研究.结果表明,共沉淀法是其中最优的制备方法,氢氧化钠和尿素结合方式沉淀制备的催化剂具有较高的活性和热稳定性.使用NH3·H2O将催化剂中的铜组分滤去的研究结果表明,催化剂中的铜含量存在一最佳值,Cu在形成催化剂活性位时起重要作用,但一旦形成变换反应所需要的活性中心,只要Cu的含量达到一定值后,则Cu的存在与否对催化剂的活性影响不大,甚至过多的Cu对催化活性不利.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.     

Copper-catalyzed multicomponent reactions of 2-iodoanilines,benzylamines, and elemental sulfur toward 2-arylbenzothiazoles

A relatively cheap copper salt-catalyzed, three-component approach providing 2-arylbenzothiazoles in good to excellent yields from readily available 2-iodoanilines, benzylamines, and sulfur powder is reported. This methodology allows preparation of various classes of 2-arylbenzothiazoles and provides a general, reliable approach.