Use of potassium-form cation-exchange resin as a conductimetric enhancer in ion-exclusion chromatography of aliphatic carboxylic acids

In this study, a cation-exchange resin (CEX) of the K⁺-form, i.e., an enhancer resin, is used as a postcolumn conductimetric enhancer in the ion-exclusion chromatography of aliphatic carboxylic acids. The enhancer resin is filled in the switching valve of an ion chromatograph; this valve is usually used as a suppressor valve in ion-exchange chromatography. An aliphatic carboxylic acid (e.g., CH₃COOH) separated by a weakly acidic CEX column of the H⁺-form converts into that of the K⁺-form (e.g., CH₃COOK) by passing through the enhancer resin. In contrast, the background conductivity decreases because a strong acid (e.g., HNO₃) with a higher conductimetric response in an eluent converts into a salt (e.g., KNO₃) with a lower conductimetric response. Since the pH of the eluent containing the resin enhancer increases from 3.27 to 5.85, the enhancer accelerates the dissociations of analyte acids. Consequently, peak heights and peak areas of aliphatic carboxylic acids (e.g., acetic acid, propionic acid, butyric acid, and valeric acid) with the enhancer resin are 6.3-8.0 times higher and 7.2-9.2 times larger, respectively, than those without the enhancer resin. Calibrations of peak areas for injected analytes are linear in the concentration range of 0.01-1.0 mM. The detection limits (signal-to-noise ratio = 3) range from 0.10 μM to 0.39 μM in this system, as opposed to those in the range of 0.24-7.1 μM in the separation column alone. The developed system is successfully applied to the determination of aliphatic carboxylic acids in a chicken droppings sample.     

Tunable separation of anions and cations by column switching in ion chromatography

A convenient ion chromatography method has been proposed for the routine and simple determination of anions (Cl⁻, SO₄²⁻ and NO₃⁻) and/or cations (Na⁺, NH₄⁺, K⁺, Mg²⁺ and Ca²⁺) using a single pump, a single eluent and a single detector. The present system used cation-exchange and anion-exchange columns connected in series via two 6-port switching valves or a single 10-port valve. The connection order of the ion-exchange columns could be varied by switching the valve(s). The present system therefore allowed the separation of either cations or anions in a single chromatographic run. While one ion-exchange column is being operated, the other ion-exchange column is being conditioned, i.e., the columns are always ready for analysis at any time. When 2.4 mM 5-sulfosalicylic acid was used as the eluent, the three anions and the five cations could be separated on the anion-exchange column and cation-exchange column, respectively. In order to obtain the separations of the target ions, the injection valve was placed between the two columns. Complete separations of the above anions or cations were demonstrated within 10 min each. The detection limits at S/N = 3 were 19-50 ppb (μg/l) for cations and 10-14 ppb for anions. The relative standard deviations of the analyte ions were less than 1.1, 2.9 and 2.8% for retention time, peak area and peak height, respectively. This proposed technique was applied to the determination of common anions and cations in river water samples.     

Nickel-aluminum layered double hydroxide as a nanosorbent for selective solid-phase extraction and spectrofluorometric determination of salicylic acid in pharmaceutical and biological samples

The nickel-aluminum layered double hydroxide (Ni-Al LDH) was synthesized by a simple co-precipitation method and used as a solid-phase extraction (SPE) sorbent for separation and pre-concentration of trace levels of salicylic acid (SA) from aqueous solutions. Extraction of analyte is based on the adsorption of salicylate ions on the Ni-Al (NO₃⁻) LDH and/or their exchanging with LDH interlayer NO₃⁻ ions. The retained analyte on the LDH was stripped by 3 mol L⁻¹ NaOH solution and its concentration was subsequently determined spectrofluorometrically at λ_em = 400 nm with excitation at λ_ex = 270 nm. Various parameters affecting the extraction efficiency of SA on the Ni-Al (NO₃⁻) LDH, such as pH, amount of nano-sorbent, sample loading flow rate, elution conditions, sample volume and matrix effects were investigated. In the optimum experimental conditions, the limit of detection (3 s) and enrichment factor were 0.12 μg L⁻¹ and 40, respectively. The relative standard deviation (RSD) for six replicate determinations of 10 μg L⁻¹ SA was 2.3%. The calibration graph using the pre-concentration system was linear in the range of 0.3-45 μg L⁻¹ with a correlation coefficient of 0.9985. The optimized method was successfully applied to the determination of SA in blood serum, willow leaf and aspirin tablet.     

Direct determination of melamine in dairy products by gas chromatography/mass spectrometry with coupled column separation

A coupled capillary column system was developed for the qualitative and quantitative determination of melamine with isotope internal standard in dairy products by gas chromatography/mass spectrometry (GC/MS) without derivatization. A 30 m of DB-5ms ((5%-phenyl)-methylpolysiloxane, 0.25 mm i.d., 0.25 μm df) coupled with a 1.5 m of Innowax (polyethylene glycol, 0.32 mm i.d., 0.25 μm df) by a quartz capillary column connector was introduced as separation column. Three advantages were discussed for the coupled system. The sample was fortified with a ring-labeled ¹³C₃¹⁵N₃-melamine as an isotope internal standard and extracted by 1% of trichloroacetic acid aqueous solution. 2.2% of lead acetate solution was then added to deposit protein in the sample matrix. After purification by cation exchange cartridge, the sample solution was directly injected and detected by GC/MS. A six-point calibration curve ranging from 0.05 to 2 mg kg⁻¹ of melamine in sample was used to establish instrument response. The recovery was 93.9-102% with relative standard deviation from 3.1 to 8.7% when isotope internal standard used. The calculated method detection limit was 0.01 mg kg⁻¹.     

Americium and plutonium separation by extraction chromatography for determination by accelerator mass spectrometry

A simple method was developed to separate Pu and Am using single column extraction chromatography employing N,N,N′,N′-tetra-n-octyldiglycolamide (DGA) resin. Isotope dilution measurements of Am and Pu were performed using accelerator mass spectrometry (AMS) and alpha spectrometry. For maximum adsorption Pu was stabilized in the tetra valent oxidation state in 8 M HNO₃ with 0.05 M NaNO₂ before loading the sample onto the resin. Am(III) was adsorbed also onto the resin from concentrated HNO₃, and desorbed with 0.1 M HCl while keeping the Pu adsorbed. The on-column reduction of Pu(IV) to Pu(III) with 0.02 M TiCl₃ facilitated the complete desorption of Pu. Interferences (e.g. Ca²⁺, Fe³⁺) were washed off from the resin bed with excess HNO₃. Using NdF_3, micro-precipitates of the separated isotopes were prepared for analysis by both AMS and alpha spectrometry. The recovery was 97.7 ± 5.3% and 95.5 ± 4.6% for ²⁴¹Am and ²⁴²Pu respectively in reagents without a matrix. The recoveries of the same isotopes were 99.1 ± 6.0 and 96.8 ± 5.3% respectively in garden soil. The robustness of the method was validated using certified reference materials (IAEA 384 and IAEA 385). The measurements agree with the certified values over a range of about 1–100 Bq kg⁻¹. The single column separation of Pu and Am saves reagents, separation time, and cost.     

Chromatographic fingerprints of industrial toluic acids established for their quality control

The chromatographic fingerprints of industrial o-toluic acid, m-toluic acid and p-toluic acid have been established by HPLC-UV detection according to their impurity groups. HPLC separation of all relative substances involved in the groups was developed on a Kromasil C₁₈ column by using methanol-water-NH₄Ac-HAc buffer (100 mM, pH 4.70) 15/65/20 (v/v/v) as the mobile phase at a flow rate of 1.5 mL/min, and detection was operated by UV adsorption at a wavelength of 254 nm. The ultraviolet spectra corresponding to each chromatographic peak were also recorded for further identification of all components. Whether the limits of relative impurities residues in a toluic acid product are qualified or not can be intuitively estimated by analyzing its chromatogram with comparison to the fingerprint. This protocol has successfully provided some Chinese manufacturers with a simple and feasible method for quality control of toluic acids for industrial use.     

Fabrication of superporous agarose beads for protein adsorption: Effect of CaCO3 granules content

Agarose gels were fabricated by water-in-oil emulsification with the addition of CaCO₃ granules at 8–16 wt%. Thus agarose beads of different superporosities were produced after dissolving the solid porogen. The superporous agarose (SA) and homogeneous agarose gels were double cross-linked and modified with diethylaminoethyl chloride to produce anion exchangers. We have proposed to use a superporous replica (porous titania microspheres) to examine the superporous structure and pore size distribution of the soft gel. The replica was prepared with the agarose gel entrapping CaCO₃ granules by a sol–gel-templating method. It was found that the superpores created by CaCO₃ granules were uniformly distributed and ranged from 0.95 μm to 1.33 μm. The physical properties of the gels were significantly affected by the porogen content. Importantly, by increasing the solid porogen to 12 wt%, the bed permeability and effective porosity increased about 48% and 33%, respectively. Further increase in the porogen to 16 wt% led to a decrease of the mechanical strength. With increasing superpores in the beads, the dynamic adsorption capacity of the packed columns increased obviously at 305–916 cm/h. Besides, the column efficiency changed less with increasing flow velocity up to 1200 cm/h. It was concluded that the use of 12 wt% CaCO₃ granules in agarose solution was beneficial for the fabrication of the SA gel with good mechanical stability and promising performance for protein chromatography.     

Characterization of new types of stationary phases for fast and ultra-fast liquid chromatography by signal processing based on AutoCovariance Function: A case study of application to Passiflora incarnata L. extract separations

In this study, a comparative investigation was performed of HPLC Ascentis^® (2.7 μm particles) columns based on fused-core particle technology and Acquity^® (1.7 μm particles) columns requiring UPLC instruments, in comparison with Chromolith™ RP-18e columns. The study was carried out on mother and vegetal tinctures of Passiflora incarnata L. on one single or two coupled columns. The fundamental attributions of the chromatographic profiles are evaluated using a chemometric procedure, based on the AutoCovariance Function (ACVF). Different chromatographic systems are compared in terms of their separation parameters, i.e., number of total chemical components (m_tot), separation efficiency (σ), peak capacity (n_c), overlap degree of peaks and peak purity. The obtained results show the improvements achieved by HPLC columns with narrow size particles in terms of total analysis time and chromatographic efficiency: comparable performance are achieved by Ascentis^® (2.7 μm particle) column and Acquity^® (1.7 μm particle) column requiring UPLC instruments. The ACVF plot is proposed as a simplified tool describing the chromatographic fingerprint to be used for evaluating and comparing chemical composition of plant extracts by using the parameters D% – relative abundance of the deterministic component – and c_EACF – similarity index computed on ACVF.     

A generic static headspace gas chromatography method for determination of residual solvents in drug substance

In order to increase productivity of drug analysis in the pharmaceutical industry, an efficient and sensitive generic static headspace gas chromatography (HSGC) method was successfully developed and validated for the determination of 44 classes 2 and 3 solvents of International Conference of Harmonization (ICH) guideline Q3C, as residual solvents in drug substance. In order to increase the method sensitivity and efficiency in sample equilibration, dimethylsulfoxide (DMSO) was selected as the sample diluent based on its high capacity of dissolving drug substance, stability and high boiling point. The HS sample equilibration temperature and equilibration time are assessed in ranges of 125–150 °C and 8–15 min, respectively. The results indicate that the residual solvents in 200 mg of drug substance can be equilibrated efficiently in HS sampler at 140 °C for 10 min. The GC parameters, e.g. sample split ratio, carrier flow rate and oven temperature gradient are manipulated to enhance the method sensitivity and separation efficiency. The two-stage gradient GC run from 35 to 240 °C, using an Agilent DB-624 capillary column (30 m long, 0.32 mm I.D., 1.8 μm film thickness), is suitable to determine 44 ICH classes 2 and 3 solvents in 30 min. The method validation results indicate that the method is accurate, precise, linear and sensitive for solvents assessed. The recoveries of most of these solvents from four drug substances are greater than 80% within the method determination ranges. However, this method is not suitable for the 10 remaining ICH classes 2 and 3 solvents, because they are too polar (e.g. formic acid and acidic acid), or have boiling points higher than 150 °C, (e.g. anisol and cumene). In comparison with the previous published methods, this method has a much shorter sample equilibration time, a better separation for many solvents, a higher sensitivity and a broader concentration range.     

Novel oxidation reaction of prochlorperazine with bromate in the presence of synergistic activators and its application to trace determination by flow injection/spectrophotometric method

Valve-based comprehensive two-dimensional gas chromatography (GC × GC) is one of the most compact, robust, and inexpensive GC × GC instrument designs. The major drawback of a valve-based modulation configuration lies in diminished detection sensitivity. This loss in sensitivity is because under typical operating conditions the fraction of the first column (i.e., column 1) effluent transferred to the second column (i.e., column 2) is likely to be ∼5-10%. To address this loss in sensitivity, we report the development of a unique total-transfer (i.e., 100%) valve-based GC × GC, without adding complexity to the instrumentation. The new instrument design relies upon simply blocking one of the appropriate ports of the high-speed six-port diaphragm valve that is used as the modulator between columns 1 and 2. The modulation period and difference in head pressure between columns 1 and 2 are found to be the two primary variables that are controlled to provide good detection sensitivity and 100% mass transfer from column 1 to column 2. The detection sensitivity is better with a longer the modulation period. A limit of detection of 0.03 ng/μl was obtained for octane. This sensitive GC × GC configuration is also shown to provide acceptable separation peak capacity, with good separations achieved for real complex samples: gasoline and Eucalyptus oil, where compounds were spread out over much of the two-dimensional separation space. In principle, this total-transfer, valve-based GC × GC is more portable and less expensive than currently available GC × GC instrumentation.     

Preparation and performances of nanosized Ta2O5 powder photocatalyst

Nanosized-Ta₂O₅ powder photocatalyst was successfully synthesized by using sol-gel method via TaCl₅ butanol solution as a precursor. Ta₂O₅ species can be formed under 500 °C via the decomposition of the precursor. The crystalline phase of Ta₂O₅ powder photocatalyst can be obtained after being calcined above 600 °C for 4 h. The crystal size and particle size of Ta₂O₅ powder photocatalyst was about 50 nm. A good photocatalytic performance for the degradation of gaseous formaldehyde was obtained for the nanosized-Ta₂O₅ powder. The Ta₂O₅ powder formed at 700 °C for 4 h and at 650 °C for 12 h showed the best performance. The calcination temperature and time play an important role in the crystallization and photocatalytical performance of nanosized-Ta₂O₅ powder.     

Development and validation of HPLC method for determination of clotrimazole and its two degradation products in spray formulation

A novel simple isocratic HPLC method with UV detection for the determination of three compounds in spray solution (active component clotrimazole and two degradation products imidazole and (2-chlorophenyl)diphenylmethanol) using ibuprofen as an internal standard was developed and validated. The complications with different acido-basic properties of the analysed compounds in HPLC separation - while clotrimazole has pK_a 4.7, imidazole has pK_a 6.9 compared to relatively more acidic (2-chlorophenyl)diphenylmethanol - were finally overcome using a 3.5 μm Zorbax^® SB-Phenyl column (75 mm × 4.6 mm i.d., Agilent Technologies).The optimal mobile phase for separation of clotrimazole, degradation products imidazole and (2-chlorophenyl)diphenylmethanol and ibuprofen as internal standard consists of a mixture of acetonitrile and water (65:35, v/v) with pH* conditioned by phosphoric acid to 3.5. At a flow rate of 0.5 ml min⁻¹ and detection at 210 nm, the total time of analysis was less than 6 min.The method was applied for routine analysis (batch analysis and stability tests) in commercial spray solution.     

Synthesis of surface molecularly imprinted polymer and the selective solid phase extraction of imidazole from its structural analogs

A surface molecularly imprinted polymer (MIP) was synthesized by using imidazole as the template and modified silica particles as the support material. The static adsorption, solid phase extraction (SPE) and high-performance liquid chromatography (HPLC) experiments were performed to investigate the adsorption properties and selective recognition characteristics of the polymer for imidazole and its structural analogs. It was shown that the maximum binding capacities of imidazole on the MIP and the non-imprinted polymer (NIP) were 312 and 169 μmol g⁻¹, respectively. The adsorption was fast and the adsorption equilibrium was achieved in 30 min. The binding process could be described by pseudo-second order kinetics. Compared with the corresponding non-imprinted polymer, the molecularly imprinted polymer exhibited much higher adsorption performance and selectivity for imidazole. The selective separation of imidazole from a mixture of 1-hexyl-3-methylimidazolium bromide ([C₆mim][Br]) and 2,4-dichlorophenol could be achieved on the MIP-SPE column. The recoveries of imidazole and [C₆mim][Br] were 97.6-102.7% and 12.2-17.3%, respectively, but 2,4-dichlorophenol could not be retained on the column. The surface molecularly imprinted polymer presented here may find useful application as a solid phase absorbent to separate trace imidazole in environmental water samples. This may also form the basis for our research program on the preparation and application of alkyl-imidazolium imprinted polymers.     

Single-run ion chromatographic separation of inorganic and low-molecular-mass organic anions under isocratic elution: Application to environmental samples

For the isocratic ion chromatography (IC) separation of low-molecular-mass organic acids and inorganic anions three different anion-exchange columns were studied: IonPac AS14 (9 μm particle size), Allsep A-2 (7 μm particle size), and IC SI-50 4E (5 μm particle size). A complete baseline separation for all analyzed anions (i.e., F⁻, acetate, formate, Cl⁻, NO₂⁻, Br⁻, NO₃⁻, HPO₄²⁻ and SO₄²⁻) in one analytical cycle of shorter than 17 min was achieved on the IC SI-50 4E column, using an eluent mixture of 3.2 mM Na₂CO₃ and 1.0 mM NaHCO₃ with a flow rate of 1.0 mL min⁻¹. On the IonPac AS14 column, it was possible to separate acetate from inorganic anions in one run (i.e., less than 9 min), but not formate, under the following conditions: 3.5 mM Na₂CO₃ plus 1.0 mM NaHCO₃ with a flow rate of 1.2 mL min⁻¹. Therefore, it was necessary to adapt a second run with a 2.0 mM Na₂B₄O₇ solution as an eluent under a flow rate of 0.8 mL min⁻¹ for the separation of organic ions, which considerably enlarged the analysis time. For the Allsep A-2 column, using an eluent mixture of 1.2 mM Na₂CO₃ plus 1.5 mM NaHCO₃ with a flow rate of 1.6 mL min⁻¹, it was possible to separate almost all anions in one run within 25 min, except the fluoride-acetate critical pair. A Certified Multianion Standard Solution PRIMUS for IC was used for the validation of the analytical methods. The lowest RSDs (less than 1%) and the best LODs (0.02, 0.2, 0.16, 0.11, 0.06, 0.05, 0.04, 0.14 and 0.09 mg L⁻¹ for F⁻, Ac⁻, For⁻, Cl⁻, NO₂⁻, Br⁻, NO₃⁻, HPO₄²⁻ and SO₄²⁻, respectively) were achieved using the IC SI-50 4E column. This column was applied for the separation of concerned ions in environmental precipitation samples such as snow, hail and rainwater.     

Preparation and characterization of novel macroporous cellulose beads regenerated from ionic liquid for fast chromatography

Macroporous cellulose beads (MCB) used as anion exchangers were successfully prepared from cellulose solution in ionic liquid by double emulsification followed by cross-linking and modification with diethylaminoethyl. The pore structure and properties of the MCB were investigated and the results were compared with homogeneous cellulose beads (HCB). The MCB in size of about 71 μm is characterized by two sets of pores, i.e., diffusion pores (10–20 nm) and macropores (800–2000 nm), determined by mercury porosimeter. In addition, the bed permeability and effective porosity for BSA of MCB-packed column are 58% and 25% higher than those of HCB-packed column, respectively. The adsorption properties of MCB were evaluated, and compared with HCB and commercial absorbent (Sepharose 6 Fast Flow, CSFF). It is found that the pore diffusivity of BSA in MCB is over 7.9 times higher than HCB, and 6.7 times higher than CSFF, respectively. While the equilibrium adsorption capacity (q_m) of BSA on MCB is obviously lower than that on HCB and CSFF, the dynamic binding capacity (DBC) on MCB at 10% breakthrough reaches 47.7 mg/mL, higher than HCB (40.3 mg/mL) and CSFF (46.2 mg/mL) at flow rate of 360 cm/h. In addition, the MCB-packed column showed better column efficiency over the HCB packed one. Therefore, we demonstrated that the MCB possessed more advantages than other ones, like HCB and CSFF, and was expected as an ideal material for fast chromatography.     

Hierarchical chlorine-doped rutile TiO2 spherical clusters of nanorods: Large-scale synthesis and high photocatalytic activity

In this study, we report the synthesis of hierarchical chlorine-doped rutile TiO₂ spherical clusters of nanorods photocatalyst on a large scale via a soft interface approach. This catalyst showed much higher photocatalytic activity than the famous commercial titania (Degussa P25) under visible light (λ>420 nm). The resulting sample was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution TEM (HRTEM), nitrogen adsorption, X-ray photoelectron spectroscopy (XPS), UV-vis diffuse reflectance spectroscopy, ¹H solid magic-angle spinning nuclear magnetic resonance (MAS-NMR) and photoluminescence spectroscopy. On the basis of characterization results, we found that the doping of chlorine resulted in red shift of absorption and higher surface acidity as well as crystal defects in the photocatalyst, which were the reasons for high photocatalytic activity of chlorine-doped TiO₂ under visible light (λ>420 nm). These hierarchical chlorine-doped rutile TiO₂ spherical clusters of nanorods are very attractive in the fields of environmental pollutants removal and solar cell because of their easy separation and high activity.     

高效液相色谱法分离和测定小麦中的5种内源激素

建立了高效液相色谱法(HPLC)用于分离和测定小麦中的吲哚乙酸(IAA)、脱落酸(ABA)、赤霉素(GA₃)、玉米素(ZT)和水杨酸(SA)5种植物内源激素。经过条件优化,选用甲醇作为样品提取溶剂。然后,经石油醚和乙酸乙酯萃取,经Sep-Pak C18小柱纯化。液相色谱的分离采用Eclipse XDB-C₁₈ (250 mm×4.6 mm, 5 μm)反相色谱柱;流速为1 mL/min;进样量10 μL。检测器波长设置为254 nm; 14.5 min时切换到240 nm; SA洗脱后即18 min时切换回254 nm。流动相A为甲醇,B为乙酸溶液(pH 3.6)。梯度条件为0~7 min, 20%A; 7~10 min, 20%A~28%A; 10~17 min, 28%A; 17~19 min, 28%A~40%A; 19~35 min, 40%A。结果表明,小麦中各激素的分离效果理想,加标回收率达96.9%~98%,相对标准偏差在1.54%~2.29%之间。因此,该方法的建立为快速、准确地分离和测定小麦内源激素提供了可靠的方法。     

Structural,theoretical and multinuclear NMR study of mercury(II) complexes of phosphorus ylides: Mono and binuclear complexes

Reaction of phosphorus ylide Ph₃PCHC(O)C₆H₄Cl (Y₁) with HgX₂ (X = Cl, Br and I) and ylide (p-tolyl)₃PCHC(O)CH₃ (Y₂) with HgI₂ in equimolar ratios using methanol as solvent leads to binuclear products. The bridge-splitting reaction of binuclear complex [(Y₁) · HgCl₂]₂ by DMSO yields a mononuclear complex containing DMSO as ligand. O-coordination of DMSO is revealed by single crystal X-ray analysis in mononuclear complex of [(Y₁) · HgCl₂ · DMSO]. C-coordination of ylides is confirmed by X-ray structure of binuclear complex [(Y₂) · HgI₂]₂. Characterization of the obtained compounds was also performed by elemental analysis, IR, ¹H, ³¹P, and ¹³C NMR. Theoretical studies on mercury(II) complexes of Y₁ show that formation of mononuclear complexes in DMSO solution in which DMSO acts as a ligand, energetically is more favorable than that of binuclear complexes.     

Separation of zinc compounds by sequential metal vapor elution analysis with atomic absorption detection

The separation of zinc compounds, containing zinc chloride, nitrate, and sulfate, at low concentrations by sequential metal vapor elution analysis (SMVEA) with argon carrier gas was reported. A molybdenum column, inserted with a tungsten wire, was developed for the separation of zinc compounds by SMVEA. The optimum separation conditions were a vaporization temperature of 1370 K, a column temperature of 1350 K, and a carrier gas flow rate of 2.5 mL min⁻¹. Under the optimized experimental conditions, the zinc compounds could be roughly separated by SMVEA, although a part of peak profiles overlapped. The number of theoretical plates was 36 for ZnCl₂, 62 for Zn(NO₃)₂, and 80 for ZnSO₄ in the SMVEA column. The present SMVEA system may be able to be applied widely to various analytical instruments.     

Single-walled carbon nanotubes as stationary phase in gas chromatographic separation and determination of argon, carbon dioxide and hydrogen

A chromatographic technique is introduced based on single-walled carbon nanotubes (SWCNTs) as stationary phase for separation of Ar, CO₂ and H₂ at parts per million (ppm) levels. The efficiency of SWCNTs was compared with solid materials such as molecular sieve, charcoal, multi-walled carbon nanotubes and carbon nanofibers. The morphology of SWCNTs was optimized for maximum adsorption of H₂, CO₂ and Ar and minimum adsorption of gases such as N₂, O₂, CO and H₂O vapour. To control temperature of the gas chromatography column, peltier cooler was used. Mixtures of Ar, CO₂ and H₂ were separated according to column temperature program. Relative standard deviation for nine replicate analyses of 0.2 mL H₂ containing 10 μL of each Ar or CO₂ was 2.5% for Ar, 2.8% for CO₂ and 3.6% for H₂. The interfering effects of CO, and O₂ were investigated. Working ranges were evaluated as 40-600 ppm for Ar, 30-850 ppm for CO₂ and 10-1200 ppm for H₂. Significant sensitivity, small relative standard deviation (RSD) and acceptable limit of detection (LOD) were obtained for each analyte, showing capability of SWCNTs for gas separation and determination processes. Finally, the method was used to evaluate the contents of CO₂ in air sample.