光致变色含氟丙烯酸酯涂层的制备及性能

选取十二烷基硫酸钠(SDS),辛基苯基聚氧乙烯醚(OP-10)为复合乳化剂,过硫酸钾(KPS)为引发剂,将2-(全氟己基)乙基甲基丙烯酸酯(PFM)与丙烯酸酯类单体采用预乳化-半连续种子乳液聚合法进行乳液共聚,再将羟基螺吡喃(SPOH)与乳液进行物理共混,制得光致变色含氟丙烯酸酯乳液。通过多种表征手段研究丙烯酸正丁酯(n-BA)和甲基丙烯酸甲酯(MMA)软硬单体的质量比,SPOH的用量对聚合反应和乳胶膜性能的影响。结果表明,加入含氟单体后乳胶膜与水、油的接触角提高,热稳定性提高;加入SPOH的质量分数为1. 25%时,乳胶膜具有较好的光致变色性能。     

两亲性RAFT试剂存在下丙烯酸六氟丁醋和苯乙烯的无皂乳液聚合

合成了具有两亲性结构的可逆加成断裂链转移(RAFT)试剂,在RAFT试剂的作用下,通过无皂乳液聚合方法合成了丙烯酸六氟丁酯与苯乙烯的共聚物.研究了RAFT试剂浓度和聚合温度对聚合动力学、聚合反应可控性及乳胶粒粒径的影响.通过红外光谱(FTIR)、核磁共振谱(1H NMR)、示差扫描量热仪(DSC)、凝胶渗透色谱仪(GPC)及表面张力仪表征了共聚物的结构、玻璃化转变温度(Tg)、分子量和分子量分布及乳胶膜表面性能.结果表明,得到的苯乙烯和丙烯酸六氟丁酯共聚物无皂乳液的乳胶粒粒径在100 nm左右且呈单分散分布.当RAFT试剂浓度高于0.016 mol/L时聚合体系有较好的可控性.共聚物乳液的乳胶膜对水和二碘甲烷的接触角都很高.     

淀粉/丙烯酸反相乳液体系的稳定性研究

以丙烯酸(AA)单体的水溶液为水相,液体石蜡为油相,失水山梨醇三油酸酯(Span 85)和辛基苯基聚氧乙烯醚(Opan 10)为复合乳化剂,合成了淀粉/丙烯酸反相乳液;考察了乳化剂亲水亲油平衡值(HLB值)、油水比、乳化剂用量、单体浓度、温度对乳液稳定性和类型的影响.结果表明,合成淀粉/丙烯酸稳定反相乳液体系的适宜条件...     

室温自交联丙烯酸酯乳液的制备与表征

使用3种含不饱和双键硅氧烷,乙烯基三(β-甲氧基乙氧基)硅烷(A172)、乙烯基三乙氧基硅烷(VTES)和γ-甲基丙烯酰氧丙基三甲氧基硅烷(A174)为功能单体,采用半连续乳液聚合法制备了室温自交联丙烯酸酯乳液,探讨了硅氧烷功能单体在不同pH条件下水解情况以及其种类和用量对乳液及乳胶膜性能的影响.结果表明,pH在7～9之间时硅氧烷功能单体水解最慢;A172在pH为8.4时5h内就水解完全;增加VTES和A174的用量均能提高乳胶膜的交联度、力学性能和耐水性.控制聚合过程的pH值以抑制硅氧烷功能单体的水解并调节乳液成膜时的pH值以加速硅氧烷功能单体的水解从而增强胶膜的交联程度,发现酸性或碱性条件下得到乳胶膜比中性条件下胶膜的力学和耐水性能均有不同程度的提高,并且在酸性条件下胶膜的性能提高最多.对比使用A174和VTES制备的胶膜,发现这种方法对含有A174胶膜的效果不明显,而含VTES胶膜的性能提高最为显著.     

聚合物纳米粒子乳液的制备及性能研究——添加组分对乳胶粒子形态及胶膜吸水率的影响

本文采用种子微乳液聚合方法,经后期氨化反应,合成了聚丙烯酸酯纳米粒子乳液,讨论了乳化剂、缓冲剂和水溶性丙烯酸单体等添加组分对乳粒子形态和胶膜吸水率的影响,并探讨了微乳液聚合的反应机理。     

有机硅-聚氨酯共聚乳液的制备和乳胶膜相结构及其性能研究

以端羟丙基聚二甲基硅氧烷(HP-PDMS)、异佛尔酮二异氰酸酯、2,2-二羟甲基丁酸等为主要原料,采用分步投料法和无皂相反转乳化工艺制得粒径约50 nm的有机硅-聚氨酯共聚乳液,并对有机硅-聚氨酯乳胶膜的相结构和性能进行了表征,考察了HP-PDMS用量对乳胶膜相结构和性能的影响.DSC测试结果显示,与聚醚型聚氨酯乳胶膜相比,有机硅-聚氨酯乳胶膜中存在明显的相分离结构.FTIR分析结果表明,有机硅-聚氨酯乳胶膜硬段之间存在较强的氢键,它促进了相分离结构的形成.从AFM相图上可以观察到有机硅-聚氨酯乳胶膜中存在明显的海岛型相分离结构,其中聚硅氧烷软段的无定形微区构成了岛状分散相.随着有机硅含量的增加,有机硅-聚氨酯乳胶膜的相分离程度增加,弹性模量降低,断裂伸长率和柔韧性显著升高.有机硅-聚氨酯乳胶膜的起始分解温度低于聚醚型聚氨酯乳胶膜,但其在高温阶段的稳定性明显优于后者;对乳胶膜接触角和吸水率的研究表明,有机硅-聚氨酯乳胶膜的耐水性远高于聚醚型聚氨酯乳胶膜.     

有机硅改性丙烯酸酯共聚乳液合成方法及胶膜性能的研究

用一次投料法、单体乳液滴加法和引发剂滴加法有机硅改性丙烯酸酯共聚乳液，聚合过程、胶粒形态及乳液稳定性的观测结果表明：单体乳液滴加法是合成该类乳液的最佳方法，研究了单体乳液滴加法中有机硅含量与聚合反及胶膜性能的关系，结果表明：有机硅含量在１５％以下时，聚合反应可以顺利进行，胶膜性能不仅依赖于聚合时有机硅单体的总量，而且还依赖于有机硅单体中活性硅氧烷所占的比例。     

~5O-MMT/BA-VAc原位共聚乳液的制备及胶膜性能研究

采用原位乳液聚合方法,制备了O-MMT/BA-VAc复合乳液,对复合乳液及胶膜的性能进行了详细研究。研究结果表明:当O-MMT引入量小于0.8wt.%时,乳液的聚合稳定性以及储存稳定性较好;复合胶膜的耐水性能随着O-MMT引入量的增大呈先增强后减弱趋势,当改性MMT用量为0.5wt.%时,复合胶膜具有最佳耐水性能,吸水率比BA-VAc胶膜降低了75%,相同添加量下,复合胶膜达到最佳拉伸强度,为22.9MPa。     

高固含量低粘度P(MMA/BA/AA)乳液的制备及性能研究

先利用半连续种子乳液聚合法制备固含量为50%,粒径480nm的单分散甲基丙烯酸甲酯(MMA)、丙烯酸丁酯(BA)与丙烯酸(AA)的共聚物种子乳液;然后以上述种子乳液为介质,十二烷基硫酸钠为乳化剂,碳酸氢钠为缓冲剂,过硫酸铵为引发剂制备固含量72%,乳胶粒具有二元分布特征的高固含量、低粘度稳定乳液:其中大乳胶粒径500～600nm,小乳胶粒径约80nm.所得乳液中乳化剂总含量为聚合物质量的2.1%;粘度在剪切速率为21s-1时为400mPa·s.另外,相对于常规乳液,所制备高固含量乳液胶膜具有更好的光泽度.     

室温自交联型聚丙烯酸酯纳米乳液的研究

本文分别用反应性乳化剂和常规乳化剂合成了室温自交联丙烯酸纳米乳液,并对其乳液的流变性能进行了研究,发现:反应性乳化剂所得乳液的表观粘度ηa、稠度系数K、零剪切粘度η0均比常规乳化剂所得乳液的增大。并用XPS对乳胶膜进行分析表明,反应性乳化剂在乳液的干燥成膜过程中不易向胶层表面迁移富集。与常规乳化剂体系的乳液相比,反应性乳化剂体系的乳液挥发速率快,吸水率低。并对两种乳液进行了粒径大小及分布的表征。     

含氟丙烯酸酯共聚乳液及其膜表面特性的研究

以十二烷基硫酸钠 (SDS)和OP 10混合乳化剂 ,制备了甲基丙烯酸全氟辛基乙酯 (FMA8) 甲基丙烯酸丁酯 (BMA) 甲基丙烯酸 (MAA)共聚乳液 .通过DSC、FT IR、1 H NMR对共聚物的结构、组成进行了表征研究 .采用JZHY 180界面张力仪研究了共聚乳液膜表面的性质 ,结果表明 ,随着共聚物中全氟单体含量的增加 ,共聚物膜的表面能显著降低 ,当全氟单体的含量达到 2 5wt %时 ,其表面能降低到 19 74mJ m2 .X ray光电子能谱(XPS)对共聚物表面原子组成的分析结果表明 ,共聚物表面氟的含量远高于其平均含量 ,证明了含氟基团的趋表现象 .经退火处理 ,共聚物膜表面的氟含量增加 ,表面自由能降低     

STUDY ON THE POLYMERIZATION KINETICS AND STABILITY OF P(UA)/MMA MICROEMULSION*

 Urethane acrylate anionomer (APUA) as a kind of new type polymerizable emulsifier was synthesized using 2,4-toluene diisocyanate (TDI), polypropylene glycol (PPG), 2-hydroxyethyl methacrylate (HEMA) and dimethylolpropionic acid (DMPA). The critical micelle concentration (CMC) of APUA was measured by the methods of conductance and surface tension. The comparative studies between polymerizable emulsifier AUPA and conventional emulsifier sodium dodecyl sulfate (SDS) were carried out in the emulsion polymerization of methyl methacrylate (MMA). Polymerization kinetics,stability, size and morphology of the latex particles were investigated. It was found that in APUA both water soluble initiator potassium persulfate (KPS) and oil soluble initiator 2,2'-azobisisobutyronitrile (AIBN) can start the reaction of MMA, and the polymerization rate and yield were very high. On using AIBN as an initiator, the conversion-time behavior of MMA with APUA as emulsifier was different to that of SDS as emulsifier, signifying a different nucleation mechanism of the polymer latex particle. The average size of the two kinds of particles is about 50 nm. The particle size decreases with increasing emulsifier concentration. On using KPS as the initiator, APUA as emulsifier, cross-linking hydrogel of PMMA would be formed, but SDS was used as emulsifier and the hydrogel of PMMA was not present.     

Properties and characterization of novel cationic polyacrylate latex containing fluorine and silicon prepared with soap-free emulsion polymerization

The novel cationic polyacrylate latex containing fluorine silicon was successfully prepared via soap-free emulsion polymerization of butyl acrylate, methyl methacrylate, vinyltriethoxysilane and hexafluorobutylmethacrylate in water phase, which were initiated with water soluble azo initiator and emulsified with the mixed surfactants polymerizable emulsifier and OP-10. The films of the resultant latex were characterized by Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) and contact angle (CA) determinator, respectively. In comparison with the conventional polyacrylate latex, the thermal stability and water resistance of novel latex film are improved. The conditions of preparing the novel cationic acrylate latexes were optimized. The optimum conditions of preparing the novel latex are as follows: the amount of emulsifiers and the initiator are 6.0% and0.3%, respectively; both the amount of VETS and amount of HFMA are 6.0%. In this case, the conversion is high and the polymerization stability is good.     

含氟丙烯酸酯共聚乳液的制备及表征

采用十二烷基硫酸钠和壬基酚聚氧乙烯醚(OP-10)混合乳化剂，制备了粒径为40-50nm的甲基丙烯酸全氟辛基乙酯(FMA8)-甲基丙烯酸丁酯(BMA)-甲基丙烯酸(MA)共聚物乳液。通过DSC、、FTIR、^1H-NMR等手段对共聚物进行了表征。考察了乳液的稳定性、乳胶膜的吸水性和耐溶剂性以及全氟单体的含量对聚合反应的影响。     

氟含量对含氟丙烯酸酯共混乳胶膜梯度结构和表面性能的影响

首先将制备出的平均粒径较小的含氟丙烯酸酯均聚物乳液与平均粒径较大的纯丙烯酸酯共聚物乳液按不同的比例( 1/9,2/8,3/7,4/6,5/5)共混,接着将各共混乳液在室温下(20℃)玻璃基材上干燥后,于110℃/210℃下热处理一段时间.运用接触角法,XPS、AFM、SEM-EDX等详细研究了共混乳胶膜中含氟组分含量对...     

Kinetic and particle size studies of emulsion polymerization of methyl methacrylate and styrene with using polyamidoamine dendrimer as seed

The emulsion polymerization of methyl methacrylate (MMA) and styrene (St) were investigated with using polyamidoamine (PAMAM) dendrimer as seed, potassium persulfate as initiator and sodium dodecyl sulfate as emulsifier. The effects of 4.0GPAMAM dendrimer concentration, initiator concentration, emulsifier concentration, monomer concentration, and polymerization temperature on the monomer conversion and polymerization rate were investigated. At the same time, the influence of the generation of PAMAM dendrimer on latex particle size was studied also. The results showed that the monomer conversion and polymerization rate increased with increasing initiator concentration, emulsifier concentration, monomer concentration, and polymerization temperature. But polymerization rate increased firstly with an increase in the 4.0GPAMAM dendrimer from 0.03 g to 0.09 g and then decreased with further increase to 0.12 g. When the concentration of 4.0GPAMAM dendrimer less than 1.449 × 10^?4 mol/L, the kinetic equation can be expressed by Rp∝[4.0GPAMAM]^0.772[SDS]^0.562[KPS]^0.589[M]^0.697, and the activation energy (Ea) of emulsion polymerization is 62.56kJ/mol. In additional, the copolymer latex particle size decreased and possessed monodispersity with increasing the generation of PAMAM dendrimer. According to FT-IR spectrum analysis, PAMAM dendrimer is successfully incorporated into the poly(PAMAM-St–MMA) latex particles.     

超声无皂乳液聚合制备BA/St/AM三元共聚物乳胶粒及其聚合机理研究

将超声技术引入到无皂乳液聚合方法中,在不加入任何引发剂和乳化剂的情况下,制备了丙烯酸丁酯(BA)/苯乙烯(St)/丙烯酰胺(AM)三元共聚纳米乳胶粒.研究了不同超声时间对单体转化率、乳胶粒粒径以及乳液粘度的影响.同时还探讨了超声无皂乳液聚合机理,认为AM在聚合过程中起到了引发和稳定的作用.TEM照片表明,乳胶粒直径大约在80nm左右,FTIR及DSC分析表明产物为三元共聚物,而不是共混物.     

Carboxylic‐group distribution of carboxylated acrylate copolymer latexes with their properties in the presence of acrylic acid and monobutyl itaconate

A series of carboxylated acrylate copolymer latexes were prepared via two different emulsion polymerization technologies with different carboxylic‐group distribution and morphologies. The effects of the emulsifier, the initiator, and the carboxylic monomers [acrylic acid (AA) or monobutyl itaconate (MBI)] on the total conversion of the monomers and the properties of acrylate latexes and films have been investigated. The distribution of carboxylic groups (?COOH) measured by conductometric titration shows that the concentration of surface –COOH (C_s) and embedded –COOH (C_b) both increase with the increase of the amount of carboxylic monomers. For the latexes containing AA, –COOH tends to distribute on the surface of latex particles and in the aqueous phase, whereas –COOH tends to concentrate inside the core of latex particles for the latexes containing MBI. Transmission electron microscopy demonstrates that the latex particles are regular with narrow size distribution and have significant differences in morphologies when different carboxylic monomers and polymerization technologies were used. The stability of latex is satisfactory through the results of common stability and zeta potential tests. Moreover, the water absorption and contact angle experiment tests also revealed that the water resistance of the latex films is good. Copyright © 2011 John Wiley & Sons, Ltd.     

Miniemulsion copolymerization of vinyl acetate and butyl acrylate. I. Differences between the miniemulsion copolymerization and the emulsion copolymerization processes

Differences between the emulsion copolymerization and miniemulsion copolymerization processes, in terms of emulsifier adsorption, emulsion stability, polymerization kinetics, copolymer composition and dynamic mechanical properties were studied for the comonomer mixture of 50:50 molar ratio vinyl acetate (VA+)—butyl acrylate (BuA), using sodium hexadecyl sulfate (SHS) as a surfactant and hexadecane (HD) as a co-surfactant. The use of hexadecane with the appropriate SHS initial concentration led to a higher adsorption of surfactant, smaller droplet size, higher stability of the emulsions, lower polymerization rates, and larger latex particle size. The copolymer composition during the initial 70% conversion was found to be less rich in Vac monomer units for the miniemulsion process. The dynamic mechanical properties of the copolymer films showed less mixing between the BuA-rich core and the VAc-rich shell in the miniemulsion latexes compared to the conventional latex films.     

壳多糖与丙烯酸丁酯的乳液接枝共聚研究

以十二烷基苯磺酸钠为乳化剂，过硫酸钾－亚硫酸氢钠为引发剂，研究了壳多糖与丙烯酸丁醋的乳液共聚合，结果表明当［Ｋ２Ｓ２Ｏ８］＝［ＮａＨＳＯ３］＝２．５７×１０－３ｍｏｌ·１－１，［ＢＡ］＝０．６８ｍｏｌ．１－１，［Ｃｈｉｔｏｓａｎ］＝１９．２ｇ·ｌ－１，在７０℃下反应５小时，共聚反应的接技率和接枝效率均较高．用红外光谱，差热分析，Ｘ射线衍射，扫描电镜对接技共聚物进行了表征，此外测试了共聚物胶乳成膜的机械性能，表明用丙烯酸丁酯对壳多糖进行接枝改性，可提高壳多糖的韧性，扩大其应用范围．