改进型铜基甲醇合成催化剂NC208的活性相谱学表征

利用ＸＲＤ和ＦＴＩＲ等谱学方法，对改进型铜基联醇催化剂ＮＣ２０８和工业催化剂Ｃ２０７的活性相进行了谱学表征。实验结果表明，联醇铜基甲醇合成催化剂的活性中心可能是“Ｃｕｘ＾０－Ｃｕ＾＋－Ｏ－Ｚｎ＾２＋／Ａｌ２Ｏ３－ＭＯｘ”；添加少量金属氧化物助剂的改进型ＮＣ２０８催化剂工作表面Ｃｕ＾＋活性位的浓度比Ｃｕ－Ｚｎ－Ａｌ三组份工业催化剂Ｃ２０７高；ＮＣ２０８催化剂能维持工作表面具有较大的Ｃｕ＾＋／Ｃｕ＾０     

Cu，Pd－ZSM－5上NO分解和CO氧化的催化作用

双交换Ｃｕ，ｐｄ－ＺＳＭ－５催化剂（Ｃｕ交换度为１０５％，Ｐｄ交换度分别为３．４％和３３％）对ＣＯ氧化反应有活性增强作用，对ＮＯ分解反应不存在增强效应．双交换催化剂在于交换程序不同，而表面物种不同，活性组分的分布状态不同，因而有不同的活性．先交换Ｃｕ，４００℃焙烧后再交换ｐｄ的Ｃｕ－Ｐｄ－ＺＳＭ－５催化剂，对上述两类反应的活性存双组分催化剂中均为最高．Ｈ_２－ＴＰＲ谱表明，共交换的Ｃｕ－Ｐｄ－ＺＳＭ－５中尚有部分ＣｕＣｌ＋占据了部分交换位置，而使ＣＯ氧化活性稍有下降．Ｎ_２－ＤＴＡ和Ｈ_２－ＴＰＲ谱结果表明，Ｐｄ交换到Ｃｕ－ＺＳＭ－５中后，抑制了吸附水和水合铜化合物的形成，由此提高了在２００—３００℃时氧的吸附量．后者的大小和ＣＯ氧化活性有顺变关系．Ｎ_２－ＤＴＡ谱中３４０—４４５℃的放热峰可能分别表征了和ＮＯ分解活性有关的铜氧桥或把氧桥的形成，该放热峰的峰温愈低，峰面积愈大，则ＮＯ分解活性愈高．     

Cu－Fe－Ce－O／γ－Al_2O_3催化CO＋NO反应的TP－FT－IR研究

运用ＴＰ－ＦＴ－ＩＲ技术研究了ＣＯ、ＮＯ、ＮＯ＋ＣＯ在负载型Ｃｕ－Ｆｅ－Ｃｅ－Ｏ（Ⅰ）和Ｃｕ－Ｆｅ－Ｏ（Ⅱ）催化剂上的吸附行为。研究表明，ＮＯ具有比ＣＯ更强的吸附能力，可与表面氧反应生成硝基、亚硝酸盐、硝酸盐等物种．在ＮＯ＋ＣＯ反应过程中，在催化剂表面存在（ＣＯ．ＮＯ）＊表面络合物（２４００—２４３０ｃｍ￣（－１））和ＮＣＯ＊（异氰酸盐）表面物种，其关系为：ＣＯ＊＋ＮＯ＊→（ＣＯ．ＮＯ）＊＋＊→ＮＣＯ＊＋Ｏ＊．在（Ⅱ）中加入铈，能提高ＣＯ在表面的吸附强度，使ＮＣＯ＊的稳定性下降，同时对ＮＯ在表面的吸附产生影响。根据研究的结果，提出了ＮＯ＋ＣＯ在模型催化剂上的表面反应机理．     

不同方法制备的Cu－Co低碳醇含成催化剂的比较研究Ⅱ．H_2－TPD，CO－TPD及CO／H_2TPSR的研究

本文采用Ｈ２－ＴＰＤ，ＣＯ－ＴＰＤ及ＣＯ／Ｈ２ＴＰＳＲ技术对三种方法（ＳＭＡＤ、浸渍、共沉淀）制备的Ｃｕ－Ｃｏ催化剂进行了表征，并与低碳醇合成选择性进行了关联．Ｃｕ－Ｃｏ催化剂上Ｈ２－ＴＰＤ谱中共有四个脱附峰（Ａ，Ｂ，Ｃ，Ｄ），其中Ｃ峰对应于低配位Ｃｏ中心上的活化吸附氢，其面积百分数随不同催化剂的变化规律与醇选择性的变化规律一致．与ＣＯ－ＴＰＤ谱对比，Ｃｏ及Ｃｕ－Ｃｏ催化剂上ＣＯ／Ｈ２ＴＰＳＲ谱中都出现一个新的甲烷析出峰（４７３～５７３Ｋ），归属为活化吸附氢与表面活泼碳物种之间的反应，其面积百分数随不同催化剂的变化规律与醇选择性的变化一致。基于上述结果，就ＣＯ插入中心问题进行了讨论．     

CuY和Cu－ZSM－5催化剂上NO直接分解活性及活性中心的研究

研究了ＣｕＹ，Ｃｕ－ＺＳＭ－５分子筛制备条件对ＮＯ直接分解活性的影响．结果表明，在不同酸碱度下交换的ＣｕＹ分子筛，在ｐＨ＝９时活性较好，而Ｃｕ－ＺＳＭ－５型在ｐＨ＝７时较好．随交换度提高，Ｃｕ－ＺＳＭ－５活性上升，而ＣｕＹ交换度达４５％后活性趋于平稳：用ＤＴＡ，ＴＰＤ，ＸＰＳ及ＩＲ等技术，对活性中心进行了研究，表明钢是以水合离子形式与分子筛中Ｎａ＋进行交换．Ｃｕ－ＺＳＭ－５的活性位单一，ＣｕＹ上则有两种ＮＯ吸附位．经４００℃焙烧后，铜优先占据Ｙ的β笼，此即活性位．未经焙烧的样品中铜主要以Ｃｕ２＋存在．４００℃抽空处理产生Ｃｕ＋．讨论了ＮＯ在含铜样品表面的反应过程．     

助剂对超细CuO－ZnO－SiO_2催化剂性质和CO_2加氢反应性能的影响

研究了９种助剂对用于ＣＯ２加氢反应的超细ＣｕＯ－ＺｎＯ－ＳｉＯ２催化剂性能的影响，并进行了ＸＲＤ和ＴＰＲ表征．结果表明，助剂影响超细催化剂的性质和催化性能，ＴｉＯ２、ＣｅＯ２、ＭｇＯ和Ｌａ２Ｏ３是ＣＯ２加氢合成甲醇的超细ＣｕＯ－ＺｎＯ－ＳｉＯ２催化剂体系的优良助剂．在含有不同助剂的ＣｕＯ－ＺｎＯ－ＳｉＯ２催化剂体系内存在ＣｕＯ和ＺｎＯ晶相，但除ＣｅＯ２以外，其它的助剂都可能以微晶或无定型的形式存在．ＴＰＲ研究表明，添加的助剂除ＣｅＯ２以外，都使超细ＣｕＯ－ＺｎＯ－ＳｉＯ２催化剂的还原温度提高，而且助剂对ＣｕＯ－ＺｎＯ－ＳｉＯ２催化剂活性的影响，按照助剂对ＣｕＯ－ＺｎＯ－ＳｉＯ２催化剂还原温度的影响进行了探讨     

预处理条件对用于CO_2加氢的超细CuO－ZnO－SiO_2催化剂性能的影响

采用ＸＲＤ、ＢＥＴ、ＴＰＲ手段，研究了焙烧和还原温度对超细ＣｕＯ－ＺｎＯ－ＳｉＯ２催化剂的性质及其ＣＯ２加氢反应催化活性的影响．胶体在５７３－７７３Ｋ范围内焙烧生成ＣｕＯ、Ｃｕ２Ｏ、ＺｎＯ晶相，随着焙烧温度继续升高，ＣｕＯ和ＺｎＯ晶粒逐渐变大，但催化剂的比表面积和孔容变化很小．在９７３Ｋ焙烧后出现Ｚｎ２ＳｉＯ４晶相，使催化剂比表积和孔容变小，导致催化剂活性降低．焙烧温度对催化剂活性的影响大于对ＣＯ２加氢产物分布的影响．在５４８－６４８Ｋ范围内，催化剂还原温度对其催化活性影响不大．７０３Ｋ高温还原后，可能由于Ｃｕ０晶粒的出现，使得催化剂的活性下降．ＴＰＲ研究结果进一步表明，焙烧温度影响ＣｕＯ同ＺｎＯ、ＳｉＯ２之间的相互作用和催化剂的还原行为．     

低碳醇合成Raney Cu－Co催化剂的表征

本文采用ＸＲＤ、ＸＰＳ、及Ｈ_２—ＴＰＤ技术对不同Ｃｕ／Ｃｏ比的几个ＲａｎｅｙＣｕ－Ｃｏ催化剂进行了表征．并与反应醇选择性进行了关联．结果表明：ＲａｎｅｙＣｕ－Ｃｏ催化剂均由不同Ｃｕ／Ｃｏ比的两个Ｃｕ－Ｃｏ固溶体相组成，还原（Ｈ_２，５６３Ｋ，２ｈ）前，表面除有Ｃｕ￣０和Ｃｏ￣０外，尚有少量Ｃｕ￣（＋１）和显著量的Ｃｏ￣（＋２）存在，还原后，Ｃｕ￣（＋１）几乎消失，Ｃｏ￣（＋２）仍有一定量存在，在反应温度下（５６３Ｋ），ＣＯ和ＣＯ_２均能使表面Ｃｏ￣０部分氧化，且ＣＯ_２氧化能力大于ＣＯ，而合成气（Ｈ_２／ＣＯ＝２）表现为还原的性质。三种气氛对Ｃｕ￣０无明显影响。催化剂表面Ｃｕ／Ｃｏ比高于体相Ｃｕ／Ｃｏ比，表面Ｃｕ富集显著．ＲａｎｅｙＣｕ－Ｃｏ催化剂表面有四种吸氢中心：Ｃｕ（弱吸氢中心），高配位Ｃｏ（弱吸氢中心），低配位Ｃｏ（活化吸氢中心），及强吸氢中心；对不同催化剂，表面低配位Ｃｏ中心的比例与醇选择性有一致的变化规律。基于上述结果，就ＣＯ播入中心进行了讨论。     

制备高碳醇用Cu－Fe系催化剂的活性相

用共沉淀法制备了Ｃｕ－Ｆｅ系催化剂，它是由脂肪酸甲酯加氢制备高碳醇的新催化体系．催化剂经焙烧后的物相为ＣｕＯ，γ－Ｆｅ２Ｏ３和ＭｇＯ，形成了活性相的结构前驱．在反应条件下，ＣｕＯ首先被还原为金属态的Ｃｕ０，然后γ－Ｆｅ２Ｏ３被还原为Ｆｅ３Ｏ４；Ｃｕ０和Ｆｅ３Ｏ４共同参与催化该反应．本文用ＸＲＤ，ＴＧ－ＤＴＡ和Ｍｏｓｓｂａｕｅｒ谱等手段，结合催化剂的活性测定，确定了催化剂的活性相为Ｃｕ０和Ｆｅ３Ｏ４；ＭｇＯ可改变催化剂的电子结构和几何构型，起到重要的助催化作用     

低碳醇合成Raney Cu－Co催化剂的研究Ⅱ．Cu－Co－Al合金及Raney Cu－Co催化剂的XRD表征

本文对Ｃｕ／Ｃｏ比不同的五个Ｃｕ－Ｃｏ－Ａｌ合金样及其碱抽提产物──ＲａｎｅｙＣｕ－Ｃｏ催化剂的体相结构进行了ＸＲＤ表征。结果表明：Ｃｕ－Ｃｏ－Ａｌ合金由ＣｕＡｌ、ＣｕＡｌ＿２及Ａｌ＿（１３）Ｃｏ＿４三种物相构成。随Ｃｕ／Ｃｏ原子比（０．１７～２３．１）增高，Ａｌ＿（１３）Ｃｏ＿４及ＣｕＡｌ物相逐渐减少，直至消失，ＣｕＡｌ＿２物相产生且逐渐增多。ＲａｎｅｙＣｕ－Ｃｏ催化剂由两种Ｃｕ－Ｃｏ固溶体组成，一种富铜，另一种富钴。Ｃｕ－Ｃｏ固溶体的形成发生于碱抽提或还原过程，含钴物相的存在有利于ＣｕＡ１物相的碱抽提。     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.     

Synthesis of N-substituted carbazolones from α-iodo enaminones via Pd(0)-catalyzed intramolecular coupling under microwave irradiation

A variety of N-aryl and N-alkyl carbazolones were conveniently achieved in good to high yields via Pd₂(dba)₃-mediated intramolecular coupling of N-substituted α-iodo enaminones under microwave irradiation. The Pd(0)-catalyzed cyclization was found to proceed favorably with the more electron-deficient phenyl ring during the reactions involving unsymmetrical N,N-diaryl α-iodo enaminones. This unique property enables the construction of carbazolone skeleton containing nitro substituted benzenoid ring.