双亲聚合物分子印迹自组装胶束电化学传感器研究

结合大分子自组装和分子印迹技术制备了分子印迹聚合物胶束,并通过电沉积将其固载到电极表面得到分子印迹电化学传感器.首先以甲基丙烯酸二甲氨基乙酯(DMA)、丙烯酸羟乙酯(HEA)、丙烯酸二异辛酯(EHA)和苯乙烯(St)合成了共聚物poly(DMA-co-HEA-co-EHA-co-St),在其侧链接枝上双键得到可光交联的双亲共聚物.以水为沉淀剂诱发该双亲共聚物在含有对乙酰氨基苯酚的溶液中自组装,得到印迹有对乙酰氨基苯酚的聚合物胶束,利用动态激光光散射(DLS)和透射电镜(TEM)表征其尺寸和形貌.最后通过电沉积技术诱导印迹胶束在金电极表面组装,经紫外光辐照交联后,洗脱模板分子形成分子印迹膜,制备了对乙酰氨基苯酚分子印迹传感器,通过循环伏安法、差分脉冲溶出伏安法研究此印迹传感器的性能.实验结果表明,该传感器对对乙酰氨基苯酚具有良好的选择性和灵敏度,浓度响应线性范围为1×10-6到4×10-3mol/L,检测限为3.3×10-7mol/L.     

2,4-二甲基苯胺印迹电极的零流电位法制备与应用

以电聚合方式,在石墨烯修饰的铅笔芯电极表面制备出2,4-二甲基苯胺的分子印迹聚合物,以零流电位变化的最大差值为指标获得最佳电聚合参数。磷酸缓冲溶液的pH为6.47,功能单体与模板分子的配比为1∶8,电位范围为–0.8～0.8 V,聚合圈数为26,洗脱时间为5 min。与2,4-二甲基苯胺结构相近的物质如4-氯苯胺、4-氨基联苯、联苯胺、邻甲苯胺等均不干扰测定。2,4-二甲基苯胺质量浓度的对数在0.121 2～605.908μg/L范围内与零流电位线性关系良好,相关系数为0.991,检出限为0.040 6μg/L。测定结果的相对标准偏差为0.84%(n=5),平均回收率为95.59%～101.70%。该电极制备简单,灵敏度高,选择性和稳定性好,适用于实际废水中2,4-二甲基苯胺的检测。     

零流电位法对4-氨基联苯的检测

以铅笔芯电极(PGE)为工作电极,铂电极为对电极,饱和甘汞电极为参比电极,在含4. 0×10-3mol/L丙烯酸、1. 0×10-3mol/L 4-氨基联苯(4-ABP)的磷酸盐缓冲溶液(PBS,p H 7. 17)中,采用循环伏安法以0. 1 V·s-1在-1. 6～1. 6 V电位范围循环扫描16圈,经超声洗脱6 min后制得4-氨基联苯印迹聚合物修饰电极(4-ABP-MIP/PGE)。零流电位法下,在4-ABP浓度0. 005～50μmol/L范围内,4-ABP-MIP/PGE的零流电位EZCP与4-ABP浓度的对数呈线性关系,检出限为1. 07 nmol/L。将该传感器用于实际样品中4-ABP的检测,平均回收率为96. 0%～102%。     

电聚合分子印迹传感器选择性测黑茶中槲皮素的含量

以槲皮素作为模板分子,邻氨基苯酚作为功能单体,在金电极表面通过电聚合法,制备了具有选择性识别槲皮素的分子印迹传感器。采用循环伏安法、差分脉冲伏安法研究了印迹膜的性能、结构和分子印迹效应。对功能单体与模板分子的配比、洗脱时间和印迹时间等实验参数进行了优化,并与其结构相似的化合物芦丁的选择性响应进行了比较,发现该传感器对槲皮素分子具有良好的选择性。槲皮素浓度在6.0×10-6~1.0×10-4mol/L范围内与峰电流呈线性关系,线性方程为:I(μA)=27.79+9.48lgc(mol/L)(R=0.9939),检出限为2.0×10-6mol/L。用此传感器测定黑茶中槲皮素含量的结果较为满意。     

基于纳米材料增效的2,6-二叔丁基对甲酚分子印迹电化学传感器的研究及应用

以2,6-二叔丁基对甲酚(BHT)为模板分子,以邻氨基苯硫酚功能化的纳米金为功能单体制备分子印迹聚合物。利用表面修饰技术,将石墨烯和所制备的分子印迹聚合物修饰至电极表面构建基于纳米材料增效的分子印迹电化学传感器。在优化条件下,该传感器的线性检测范围为5×10–6~1×10–2 mol/L,最低检测限为1.56×10–6 mol/L,5次重复测定结果的相对标准偏差为4.6%,样品加标回收率为96.5%~104.0%。该分子印迹电化学传感器能够实现对BHT的特异性识别,具有良好的重复性和稳定性,可用于实际样品检测。     

基于分子印迹电聚合膜的双酚A电化学传感器

以双酚A为模板分子,邻氨基苯硫酚为单体,采用自组装和电聚合方法,在电极表面制备了对双酚A有选择性的分子印迹聚合物膜.通过循环伏安法研究传感器对双酚A的响应特性.结果表明: 在6.0×10-7～5.5×10-5 mol/L浓度范围内峰电流值与浓度呈良好线性关系(r=0.991);检出限2.0×10-7 mol/L; 相对标准偏差<5%(n=9),达到稳定电流所用时间约2 min.此传感器具有良好的选择性、重现性及稳定性.通过交流阻抗技术和计时电流法表征了电极表面膜的电化学性质.将传感器初步用于实际样品的分析,获得了较满意的结果.     

三聚氰胺分子印迹表面等离子体共振传感器的制备及分析应用

以合成的烯丙基-1,3,5-三嗪-2,4,6-(1H,3H,5H)三酮为功能单体,三聚氰胺为模板分子,乙二醇二甲基丙烯酸酯为交联剂,在表面等离子体共振(SPR)传感芯片上合成了分子印迹聚合物薄膜。根据印迹聚合物的朗格缪尔方程式,计算得到三聚氰胺和分子印迹聚合物之间的结合常数为1.40×10~8L/mol。此传感器显示出对模板分子三聚氰胺的高选择性,在p H=7.5的条件下,此传感器对三聚氰胺的响应最佳,线性范围为0.1-10.0 nmol/L(R=0.9991)。将此传感器用于牛奶和奶粉中三聚氰胺的检测,检出限分别为62.6 pmol/L和56.4 pmol/L(S/N=3),回收率分别为91.5%和92.0%。     

分子印迹电化学传感器同时测定尿液中多巴胺和抗坏血酸

制备了同时检测多巴胺(DA)和抗坏血酸(AA)的分子印迹电化学传感器。该传感器以酸性铬蓝K(ACBK)为功能单体,DA/AA为模板分子,利用电化学聚合方法在电极表面合成分子印迹聚合物膜,根据DA和AA产生的氧化电流,利用差分脉冲伏安法实现DA和AA的同时测定,且DA和AA的氧化峰电位分开近300 m V。DA和AA检测限分别达6.20×10-11mol/L和1.65×10-8mol/L。传感器可应用于人尿液中DA和AA的测定。     

基于制备接枝型分子印迹膜构建农药电位型电化学传感器及其检测性能研究

基于分子设计,以氯甲基化聚砜(CMPSF)为基膜,阴离子单体对苯乙烯磺酸钠(SSS)为功能单体,N,N'-亚甲基双丙烯酰胺(MBA)为交联剂,在表面引发体系-NH2/S2O2-8的作用下,采用"接枝聚合与分子印迹同步进行"的分子表面印迹新技术,制备了接枝型农药抗蚜威分子印迹膜(MIM)。采用红外光谱(FITR)和光学显微镜(OM)对该分子印迹膜进行表征,通过等温结合实验与竞争吸附实验,考察了抗蚜威分子印迹膜的分子识别性能与机理。以该印迹膜作为敏感膜,构建了抗蚜威电位型传感器,并对其检测性能进行了考察。结果表明,所制备的接枝型印迹膜对模板抗蚜威分子具有特异的识别选择性和优良的结合亲和性,结合容量高达92μg/cm2,相对于分子结构与抗蚜威相似的阿特拉津,印迹膜对抗蚜威的选择性系数为4.537。在p H 4.0的水介质中,传感器膜电极的电位响应与抗蚜威浓度对数在1.0×10-6~1.0×10-3mol/L范围内呈良好的线性关系(r=0.999 9),其检出限为2.5×10-8mol/L;以抗蚜威分子印迹膜为敏感膜所构建的电位型传感器,其构建过程简捷,检测灵敏准确,电位响应快速(t10 s)。     

分子印迹电化学传感器的制备及其对啶虫脒的响应特性

应用恒电位沉积法制备了以壳聚糖为功能基体,啶虫脒为模板分子、戊二醛为交联剂的印迹膜电极,并构建印迹传感器.借助阳离子指示探针Ru(NH3)6Cl3,研究该印迹传感器的电化学响应特性及其对模板分子啶虫脒的分子识别性能.结果表明,印迹传感器具有良好的印迹效果,相较于结构类似物如吡虫啉等,对啶虫脒有较高的结合速率和特异性识别能力,且在啶虫脒浓度为1.0×10-7～2.0×10-5 mol/L范围内呈线性响应,为农药残留物中啶虫脒的选择性分析提供新的思路.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.     

Synthesis of N-substituted carbazolones from α-iodo enaminones via Pd(0)-catalyzed intramolecular coupling under microwave irradiation

A variety of N-aryl and N-alkyl carbazolones were conveniently achieved in good to high yields via Pd₂(dba)₃-mediated intramolecular coupling of N-substituted α-iodo enaminones under microwave irradiation. The Pd(0)-catalyzed cyclization was found to proceed favorably with the more electron-deficient phenyl ring during the reactions involving unsymmetrical N,N-diaryl α-iodo enaminones. This unique property enables the construction of carbazolone skeleton containing nitro substituted benzenoid ring.