固相萃取富集高效液相色谱法测定烟草及烟草添加剂中的重金属元素

报道用固相萃取富集,高效液相色谱法测定烟草及烟草添加剂中镍、铜、锡、铅、镉、汞的方法。样品用微波消化,消化液中的镍、铜、锡、铅、镉、汞用四-(对甲氧基苯基)-卟啉(T4MPP)柱前衍生．用C18固相萃取小柱萃取富集镍、铜、锡、铅、镉、汞的T4MPP络合物,然后用甲醇和四氢呋喃为流动相梯度洗脱,Waters Xterra^TMRP18色谱柱分离二极管阵列检测器检测。镍、铜、锡、铅、隔、汞的捡出限在2～4ng／L之间,方法相对标准偏差为1．8％～2．4％,加标回收率为96％～103％。     

微波消化-在线固相萃取富集高效液相色谱法测定饲料用灌木中痕量铅镉汞

研究了用微波消化样品,WatersXterraTMRP18(3.9mm×20mm)色谱柱在线固相萃取富集,二极管矩阵检测器检测,高效液相色谱测定饲料用灌木中痕量铅、镉、汞的方法。铅、镉和汞含量在0.1～100μg·L-1范围内与峰面积呈线性关系,方法检出限(S/N=3)为:铅2.0ng·L-1,镉1.5ng·L-1和汞2.0ng·L-1,方法相对标准偏差为2.0%～3.1%,标准回收率为94%～103%,该方法用于测定饲料用灌木中低含量的铅、镉、汞,结果满意。     

固相萃取富集-高效液相色谱法测定烟草和烟草添加剂中的重金属元素

研究了用固相萃取富集,高效液相色谱法测定烟草及烟草添加剂中镍、铜、锡、铅、镉、汞的方法。样品用微波消化后,消化液中镍、铜、锡、铅、镉、汞用四 (对氨基苯基) 卟啉[T (p AP)P]柱前衍生,用C18固相萃取小柱萃取富集镍、铜、锡、铅、镉、汞的T (p AP)P络合物,富集倍数为50倍;然后用甲醇和丙酮(均含0.05mol·L-1的pH10.0四氢吡咯 乙酸缓冲)为流动相进行梯度洗脱,WatersXterraTMRP18(3.9mm×150mm)为色谱柱,用二极管矩阵检测器检测。镍、铜、锡、铅、镉、汞的检出限分别为42,38,82,60,50和25ng·L-1。RSD为2.1%～2.8%,标准回收率为95%～103%。该方法用于测定烟草及烟草添加剂中的痕量镍、铜、锡、铅、镉、汞,结果满意。     

四-(对甲氧基基苯基)-卟啉柱前衍生,固相萃取高效液相色谱法测定痕量铁、钴、铜、锌和锰

研究了用固相萃取富集,高效液相色谱法测定环境水样中痕量Fe、Co、Cu, Zn和Mn的方法.环境水样中的Fe、Co、Cu、Zn和Mn用四-(对甲氧基苯基)-卟啉 (T4MPP) 柱前衍生,用Waters Sep-Pak-C18固相萃取小柱萃取富集Fe、Co、Cu、Zn和Mn的T4MPP络合物,富集倍数达50倍;然后用甲醇和四氢呋喃梯度洗脱为流动相,Waters XterraTM RP18色谱柱为固定相分离,用二极管矩阵检测器检测.Fe、Co、Cu、Zn和Mn的检测限分别为3.2、1.8、2.0、2.0和4.5 ng/L.方法相对标准偏差为2.1%～3.7%,标准回收率为94%～107%.该方法用于环境水样分析,结果令人满意.     

四-（对甲氧基苯基）-卟啉柱前衍生，固相萃取高效液相色谱法测定痕量铁、钴、铜、锌和锰

研究了用固相萃取富集，高效液相色谱法测定环境水样中痕量Fe、Co、Cu，Zn和Mn的方法。环境水样中的Fe、Co、Cu、Zn和Mn用四-(对甲氧基苯基)-卟啉(T4MPP)柱前衍生，用Waters Sep—Pak—C18固相萃取小柱萃取富集Fe、Co、Cu、Zn和Mn的T4MPP络合物，富集倍数达50倍；然后用甲醇和四氢呋喃梯度洗脱为流动相，Waters Xterra^TM RP18色谱柱为固定相分离，用二极管矩阵检测器检测。Fe、Co、Cu、Zn和Mn的检测限分别为：3．2、1．8、2．0、2．0和4．5ng/L。方法相对标准偏差为2．1％～3．7％，标准回收率为94％～107％。该方法用于环境水样分析，结果令人满意。     

在线富集高效液相色谱法测定饮用水中的多环芳烃

1　　引　　言多环芳烃是一类重要的致癌物质 ,环境样品中痕量的多环芳烃分析具有重要意义。其中高效液相色谱 程序波长荧光检测器检测是测定多环芳烃最常用的方法。紫外二极管矩阵检测器具有检验峰纯度、比较未知光谱与谱库光谱辅助定性的功能 ,其检测结果可靠性比程序波长荧光检测器高。但是紫外检测器灵敏度比荧光检测器低近两个数量级 ,对于清洁水样 ,多环芳烃含量很难达到紫外检测器的定量范围。为了解决清洁水样中多环芳烃的紫外二极管矩阵检测器检测 ,我们研究了色谱柱在线富集的方法 ,大大提高了多环芳烃的富集倍数 ,清洁水样中多…     

电感耦合等离子体发射光谱(ICP－OES)法测定聚碳酸酯中重金属铅、镉、汞、铬

采用微波消解法对聚碳酸酯(PC)样品进行前处理,使用电感耦合等离子体发射光谱(ICPOES)法测定聚碳酸酯中重金属铅、镉、汞、铬元素,通过对消解方式和消解试剂的研究,建立了ICP-OES法测定聚碳酸酯中重金属铅、镉、汞、铬元素的方法。结果表明,铅、镉、汞、铬加标回收率均在94.0%～105%,相对标准偏差(RSD)均小于4%,样品处理时间短,测定速度快,污染小,环保,有较高的加标回收率和精密度,适用于聚碳酸酯中重金属铅、镉、汞、铬的测定。     

塑料制品中铅、汞、镉、铬(Ⅵ)测定

塑料样品用硝酸、盐酸、高氯酸及过氧化氢(含硅样品尚须加入氢氟酸)加压消解,可按程序用微波加热或置于不锈钢压力罐中,密闭后在控温于190℃的烘箱中加热.所得试样溶液供电感耦合等离子体原子发射光谱法测定铅、汞及镉,要求及限量的盐酸抵消氯离子的影响,测定了标准物质中铅、汞、镉的含量,测得结果与证书值一致,铅、汞、镉测定值的相对标准偏差(n=9)在0.3%～8.0%之间.另取样品用二苯基羰酰二肼(DPC)光度法测定其铬(Ⅵ)含量,样品中铬(Ⅵ)用氢氧化钠-碳酸钠混合溶液和磷酸二氢钾-磷酸氢二钾缓冲溶液超声提取60 min,分取部分过滤提取液,按DPC光度法测定铬(Ⅵ)量.测得铬(Ⅵ)的平均回收率为95%,平均相对标准偏差(n=9)为0.35%.铅、汞、镉及铬(Ⅵ)的检出限(3σ)依次为0.011,0.007,0.003,0.001 mg·L-1.     

浊点萃取富集-石墨炉原子吸收光谱法同时测定环境水样和中药中超痕量铅和镉

提出了石墨炉原子吸收光谱法同时测定环境水样和中药中超痕量铅与镉的方法.以双硫腙为络合剂,在pH 7.0时,用Triton X-114非离子表面活性剂浊点萃取富集样品溶液中痕量铅和镉.用硝酸镁和磷酸二氢铵的混合液作为基体改进剂测定铅和镉,铅和镉的检出限(3s/k)分别为0.138,0.007μg·L-1,相对标准偏差(n=7)分别为1.90%,2.08%.对于10 mL样品溶液的富集倍数分别为18.3,17.7.应用所提出的方法测定了杨树叶(GBW 07604)和小麦粉(GBW08503)国家标准样品,测定结果与标准值相符.铅和镉的加标回收率分别为97.8%,94.0%(水样);98.0%,94.0%(中药样).     

离子交换伏安法同时测定水体中的镉、汞

报道了一种同时快速测定水体中痕量镉、汞的电分析方法。在 p H 4.0 0的磷酸盐缓冲溶液中 ,镉、汞在钠型蒙脱石修饰玻碳电极上通过离子交换富集 ,获得一个灵敏的阳极溶出峰 ,由此可同时测定痕量的镉、汞离子。利用该方法测定镉、汞的线性范围分别为 8× 1 0 - 9到 2× 1 0 - 6 mol/L和 4× 1 0 - 8到 7.5× 1 0 - 6 mol/L ,检出限分别是1× 1 0 - 9mol/L和 8× 1 0 - 9mol/L。该方法简便、快速 ,灵敏度高。用此修饰电极测定了水样中的镉、汞离子 ,结果令人满意     

葡萄糖苷特异性固相萃取固定相的合成、表征及应用

以马来酰亚胺基修饰凝胶载体,通过β-葡萄糖胺和2-亚氨基硫代烷盐酸盐将作为配基的β-葡萄糖脒连接到载体上,合成了一种葡萄糖苷特异性固相萃取固定相,并对其固相萃取性能进行了表征.该固定相对葡萄糖苷具有特异性识别,并成功用于固相萃取分离葡萄糖苷.     

反相液相色谱中固定相和流动相对柱相比的贡献

依据柱相比的热力学定义和反相液相色谱中溶质的计量置换保留理论(the stoichiometric dispheement heory of solute for retention，SDT-R)，对反相液相色谱中固定相和流动相性质、温度对柱相比的影响进行了研究。结果表明：固定相的种类和配基的疏水性对柱相比影响较大，而流动相中有机溶剂的种类，特别是脂肪酸作为置换剂时，对柱相比的影响更大，而柱相比受温度的影响较小。此外，通过用27种小分子溶质对柱相比的测定，其logI和Z良好的线性关系，进一步证明柱相比是一个与溶质性质无关的常数。     

Morphological studies of a hydrogen-bonded LC polymer obtained by photopolymerization in LC solvents

Anisotropic morphologies and the phase behaviour of a hydrogen-bonded LC polymer obtained by photopolymerization in two kinds of LC solvent are discussed. The hydrogen-bonded LC monomer, 4-(6-acryloyloxyhexyloxy) benzoic acid (A6OBA), was photopolymerized in 4-cyano-4′-hexyloxybiphenyl (6OCB) and in 4-cyano-4′-undecyloxybiphenyl (11OCB), which show a nematic phase and a smectic A phase, respectively. After photo-polymerization, the LC media were removed by extraction and the pure polymer was observed by scanning electron microscopy. SEM images showed that the polymer possessed fibrous morphology with a fibre diameter of a few micrometers, based on polymerization-induced phase separation. The overall geometries reflected typical LC characteristics such as schlieren and focal-conic fan textures. It was found that the hydrogen bond between benzoic acid groups in the monomer was rigid enough to fix the anisotropic phase-separated structure forming during the early stage of phase separation; however, it could not permanently maintain the fibre structure due to dissociation at elevated temperature. X-ray measurements revealed that a well developed layer structure of the hydrogen-bonded mesogen existed in the polymer obtained from the smectic phase of 11OCB, whereas a polymer layer structure could develop only partially from the nematic phase of 6OCB.     

亲水有机相-含盐水两相体系的形成机理与分相能力

亲水有机相-含盐水两相体系的形成机理与分相能力;亲水有机相;含盐水相;两相体系;分相机理;分相能力     

Oxadiazole-based unsymmetrical chiral liquid crystal dimers: synthesis and mesomorphic properties

The synthesis and liquid crystalline properties of novel chiral Schiff's base dimers containing the 1,3,4-oxadiazole ring are reported. The length of the terminal S-alkyl chain has been varied. All the compounds synthesised were thermally stable and exhibited enantiotropic mesomorphism, showing either SmC*–SmA–TGB–N*–BP or SmC*–SmA phase sequence.     

Cholesterol-based dimeric liquid crystals: synthesis,mesomorphic behaviour of frustrated phases and DFT study

Chiral unsymmetrical dimeric liquid crystals consisting of a cholesterol moiety as chiral entity and a substituted salicylidene imine core (with the substituent being butyl or fluoro or chloro group) interconnected through an even methylene spacer have been synthesised and their mesomorphic properties are characterised. All the dimers exhibit enantiotropic mesophases. The butyl homologue exhibited N* phase only, the fluoro- and chloro-substituted compound exhibited frustrated blue phases (BPs), N* phase and SmC* or twisted grain boundary (TGB) phases. The occurrence of a fluid frustrated phase, the BP, in particular, observed in compounds with a polar moiety and bent optimised conformation by density functional theory (DFT) study, indicates the importance of polar structures and bent shape of the compounds. Theoretical calculation was performed in order to study the optimised conformation, polarity and electron density distribution of the synthesised cholesterol derivatives using DFT. Time-dependent density functional theory (TD-DFT) calculation also had been carried out to investigate the absorption spectra and HOMO–LUMO energies. The experimental and theoretical absorption spectra are also presented.     

Preorganised effects of a tetramesogenic supermolecule on supramolecular assembly in the liquid crystalline phases

After preparing a homologous series of tetrameric mesogenic compounds in which two U-shaped molecules were connected via a rigid benzene derivative or a flexible alkyl chain, we investigated their phase transition behaviour using optical microscopy, differential scanning calorimetry and X-ray diffraction analysis. The compounds possessing an alkyl spacer as the central group exhibited nematic and smectic A phases just as the corresponding U-shaped molecule did. The compound possessing a 1,2-benzene unit as the connecting group showed nematic and smectic A phases, although the compound possessing a 1,3-benzene unit exhibited only an anticlinic smectic C phase. Structure–property relations of the liquid crystalline tetramers are interpreted in terms of preorganised effects of the four mesogenic units.     

Phase equilibria in the GeSe2-SnTe system

Journal of Thermal Analysis and Calorimetry - The phase diagram of the system GeSe2-SnTe is studied by means of X-ray diffraction, differential thermal and measurements of the microhardness and the...     

Time‐Resolved Phase Transitions of the Nanocrystalline Cubic to Submicron Monoclinic Phase in Zirconia

The nanocrystalline cubic, tetragonal, and submicron monoclinic phases of pure zirconia were prepared by thermal decomposition of carbonate and hydroxide precursors. The crystallization and isothermal phase transformations of the oxide were studied using high temperature X‐ray diffraction, X‐ray diffraction and Raman spectra of quenched samples. Cubic zirconia formed first, and then progressively transformed to tetragonal and monoclinic phases at temperatures as low as 320°C. The cubic, tetragonal, and monoclinic phases for ZrO₂ were found to be distinct functions of crystallite size, indicating the nanocrystalline nature of these phases. They were found to exist within critical size ranges of 50 to 140 Å, 100 to 220 Å and 190 to 420 Å (±5 Å), respectively. Thus, as the crystallites grow during annealing, they first transform from cubic to tetragonal and then from tetragonal to monoclinic at critical sizes. The classical Avrami equation for nucleation and growth was applied to the tetragonal to monoclinic phase transition.     

Obituary: Professor Frank M. Leslie FRS (1935-2000)

The synthesis of five new cholesteryl-based monomers (M-1?M-5) and the corresponding smectic comb-like polymers containing cholesteryl groups (P-1?P-5) is presented. The chemical structures were characterised by FT-IR, 1H NMR and elemental analyses. The specific optical rotations were evaluated with a polarimeter. The phase behaviour was investigated by polarising optical microscopy, differential scanning calorimetry, thermogravimetric analysis, and X-ray diffraction. The specific optical rotation values of these monomers and polymers with the same number of phenyl rings and terminal groups were nearly equal; however, they decreased with increasing the aryl numbers in the mesogenic core. The monomers M-1?M-5 showed oily streak and focal conic optical textures, or finger print textures characteristic of the chiral nematic phase. The polymers P-1?P-5 showed the smectic A phase. The melting, clearing, and glass transition temperatures increased, and the mesophase temperature ranges widened with increasing the aryl number in the mesogenic core. However, although the molecular structures of M-4 and M-5 were similar to those of M-3, namely their mesogenic cores contained three phenyl rings, their phase behaviour differed considerably, and T _m and T _i of M-4 and M-5 were less than those of M-3. In addition, M-4 and M-5 showed a clear glass transition similar to the polymer. Furthermore, the ester linkage bond and aryl arrangement in the mesogenic core also affected the phase behaviour.