共查询到19条相似文献,搜索用时 248 毫秒
1.
2.
利用软嵌式粉末电极技术研究了Y(OH)3包覆对球形Ni(OH)2电化学性能的影响. 循环伏安结果表明, 在球形Ni(OH)2的氧化过程中存在Ni(Ⅲ)和Ni(Ⅳ)的两步氧化反应, 产生的Ni(Ⅳ)不稳定, 能分解产生NiOOH和氧气, 所以可将Ni(Ⅲ)→Ni(Ⅳ)看作副反应. Y(OH)3包覆层对Ni(OH)2氧化过程后期的副反应, 特别是Ni(Ⅲ)→Ni(Ⅳ)具有较好的抑制作用. 由包覆后的Ni(OH)2制成的模拟电池表现出很好的高温性能, 在1C充放电条件下, 当Y的摩尔分数为1.61%时, 在60 ℃时所对应的容量保持率可达到25 ℃的92.7%; 当Y的摩尔分数仅为0.55 %时, 在60 ℃时所对应的质量比容量也可达到241.3 mA·h/g. 相似文献
3.
掺钇α-Ni(OH)2的研究 总被引:5,自引:0,他引:5
采用均匀络合共沉淀法,首次合成出了掺杂钇基α-Ni(OH)2,并采用XRD,FTIR和SEM分析技术,对其结构及形貌进行了研究,电化学测试表明,所制得的掺杂钇基α-Ni(OH)2与掺铝的α-Ni(OH)2和球形β-Ni(OH)2相比,敲实密度1.6g/cm2,电化学比容量330mA.h/g以上,活性物质利用率大于95%,循环可逆性好等优点。 相似文献
4.
5.
采用水热合成法制备出一种新型β-Ni(OH)2/碳纳米管(CNTs)纳米复合物,Ni(OH)2微晶粒径控制在50~80 nm之间,与CNTs直径相当,CNTs与Ni(OH)2质量比为1:15.将纳米复合物应用于活性炭(AC)/NiOOH电化学混合电容器,电化学测试表明:在0.4 A/g电流条件下,其放电比容量达279 mAh/g,是β-Ni(OH)2理论容量的96.5%;当电流密度从0.4 A/g增加至8 A/g时,电容器的容量保持率在76.5%以上,高倍率充放电特性优异.此外,纳米复合物良好的电化学可逆性使AC/NiOOH电化学混合电容器更易活化,并具有较高的充放电效率和良好的循环稳定性能. 相似文献
6.
7.
以Co(NO_3)_2·6H_2O和Ni(NO_3)_2·6H_2O为钴源和镍源,采用溶剂热法一步合成了Co(OH)_2/Ni(OH)_2复合材料,通过煅烧该复合材料可得到NiCo_2O_4。采用XRD、SEM、BET等对材料进行了表征,结果表明,Co(OH)_2/Ni(OH)_2复合材料是薄片组成的花状形貌,比表面积为37. 48m~2/g。电化学性能测试表明,Co(OH)_2/Ni(OH)_2复合材料比NiCo_2O_4具有更高的比电容值和容量保持率。在0. 5A/g的电流密度下,复合材料比电容值可达到1097. 8F/g,而NiCo_2O_4比电容值仅为86. 1F/g。因此,与煅烧后的NiCo_2O_4材料相比,Co(OH)_2/Ni(OH)_2复合材料具有更加优良的电化学性能,这为高性能超级电容器材料的制备提供了一个新思路。 相似文献
8.
本文采用球形Al/Co部分取代α型Ni(OH)2为前驱体成功制备了锂离子电池正极材料LiNi0.8Co0.15Al0.05O2。首先采用氢氧化钠与碳酸钠为沉淀剂合成出Al/Co部分取代α型Ni(OH)2,然后将之与LiOH·H2O混合,最后在氧气气氛中不同温度下热处理8h,即可得到球形LiNi0.8Co0.15Al0.05O2材料。X射线衍射结果表明,LiNi0.8Co0.15Al0.05O2材料为α-NaFeO2相。扫描电镜结果表明,材料颗粒形貌为球形。热重分析结果表明合成LiNi0.8Co0.15Al0.05O2的主反应温度在700~750℃之间。振实密度测试结果表明,750℃下制备的LiNi0.8Co0.15Al0.05O2材料可达2.2g·cm-3。恒流充放电结果表明,该材料在0.5mA·cm-2电流密度下,在3.0~4.3V间的首次充电容量可达210.3mAh·g-1,首次放电容量为179.7mAh·g-1,充放电效率为85.4%。与采用以β-Ni0.85Co0.15(OH)2为前驱体合成的LiNi0.85Co0.15O2和Al掺杂的LiNi0.8Co0.15Al0.05O2相比,尽管其首次放电容量与放电效率都有所降低,但循环性能有所提高,50周期后容量仍为初始容量的89.5%。研究表明,以球形Al/Co部分取代α型Ni(OH)2作为前驱体为球形氧化镍钴铝锂材料的制备提供了一条新的途径。 相似文献
9.
细粒度氧化钇生产的新方法 总被引:2,自引:0,他引:2
采用氨水与氯化钇溶液共沉淀制得Y(OH)3胶体, 再加草酸溶液转化, 可制得细粒度Y2O3粉末(D50=1~2 μm). 初步探讨了制备工艺中的有关因素, 在选定条件下, 沉淀过程物料浓度、温度、加入速度对最终产物D50有一定影响, 但不明显. 草酸沉淀母液最终pH值对D50影响最大. 相似文献
10.
11.
12.
外掺Y2O3对镍氢电池正极高温性能的影响 总被引:8,自引:2,他引:8
研究了外掺Y2O3对镍氢电池镍正极高温性能的影响. 通常镍正极在高温下放电比容量会骤然降低, 为了提高其高温性能, 进行了球型Ni(OH)2外掺不同比例Y2O3的实验, 对压制的镍电极在不同温度下的充放电情况进行了细致的研究. 研究发现外掺Y2O3的球型Ni(OH)2电极比普通球型Ni(OH)2电极的放电比容量在高温下要高出很多, 在0.2 C充放电情况下外掺1%是最佳比例, 它比普通球型Ni(OH)2电极的放电比容量要高出35%以上, 在1 C充放电情况下外掺0.2%是最佳比例, 它比普通球型Ni(OH)2电极的放电比容量要高出15%以上. 同时对外掺Y2O3提高镍正极放电比容量的原因也进行了初步探讨. 相似文献
13.
Shilei Gong Qing Cao Li′e Jin Cungui Zhong Xiaohua Zhang 《Journal of Solid State Electrochemistry》2016,20(3):619-628
Three-dimensional Ni(OH)2 nanoflakes were prepared via a facile and cost-effective electrodeposition method using commercial activated carbon (AC) as substrate. Nitric acid treatment (NT) and partial crystallization (PC) by metal nickel catalysis were applied for AC. The effects of the oxygen-containing functional groups and the degree of crystallization on the electrochemical performance of the electrode were investigated. The resulting Ni(OH)2/PC–NT–AC/nickel foam electrode exhibits distinct performance with a specific capacitance of 2971 F/g (scaled to the mass of active Ni(OH)2) at a current density of 6 A/g. A high capacitance of 1919 F/g was still achieved even at 40 A/g, which is much higher than Ni(OH)2/AC/nickel foam electrode and Ni(OH)2/NT–AC/nickel foam electrode. The excellent performance of Ni(OH)2/PC–NT–AC/nickel foam electrode can be attributed to the presence of large surface area and highly conductive PC–NT–AC network on nickel foam. This study presents an effective method to improve the dispersion and rate capability of Ni(OH)2 nanostructure electrodes. 相似文献
14.
The LDH of Ni with Fe, having the formula Ni(1-x)Fe(x)(OH)2(A(n-))(x/n)yH2O (A = NO3-, Cl-; x = 0.25, 0.33), scavenges CrO4(2-) ions from solution throughout the concentration range examined (0.00625-0.25 N). The CrO4(2-) uptake capacity is independent of the anion in the starting LDH but is higher when x = 0.25 (3.60 meq g(-1)) as compared to x = 0.33 (2.40 meq g(-1)). These values are higher than those observed for control compounds beta-Ni(OH)2 (1.86 meq g(-1)) and FeO(OH) (1.26 meq g(-1)), which do not have any interlayer chemistry, showing that chromate uptake takes place by its incorporation in the interlayer region by a stoichiometric anion-exchange reaction, rather than by adsorption. Nevertheless, the interaction between the LDH and the chromate ions is weak. The weak interaction is due to the mismatch between the symmetry of the chromate ions and the symmetry of the interlayer site, which introduces turbostratic disorder in the chromate-intercalated LDHs. The chromate ions can be completely leached out by soaking the LDH in a sodium carbonate solution. 相似文献
15.
在相同停留时间、不同搅拌桨线速度条件下,利用化学沉淀法制备球形氢氧化镍样品并运用SEM技术考察制得样品的形貌。研究表明:在相同的停留时间和化学条件下,随着搅拌桨线速度的提高样品的微观形貌由无定型状晶体变为大颗粒类球状晶体再变为较规则的球状晶体。利用PIV物理模拟技术模拟反应器内流场分布情况并结合XRD表征结果分析得出:在相同的停留时间和化学条件下,反应器内流场分布越均匀、速度矢量越大氢氧化镍晶体的生长越完整,结晶性、球形度和相对结晶度越高,并从流场分布的角度描述了球形氢氧化镍生长结晶的过程。 相似文献
16.
在相同停留时间、不同搅拌桨线速度条件下,利用化学沉淀法制备球形氢氧化镍样品并运用SEM技术考察制得样品的形貌。研究表明:在相同的停留时间和化学条件下,随着搅拌桨线速度的提高样品的微观形貌由无定型状晶体变为大颗粒类球状晶体再变为较规则的球状晶体。利用PIV物理模拟技术模拟反应器内流场分布情况并结合XRD表征结果分析得出:在相同的停留时间和化学条件下,反应器内流场分布越均匀、速度矢量越大氢氧化镍晶体的生长越完整,结晶性、球形度和相对结晶度越高,并从流场分布的角度描述了球形氢氧化镍生长结晶的过程。 相似文献
17.
The spherical nano-Ni(OH)2 has been characterized by a series of spectra methods such as the scanning electron microscope (SEM), the transmission electron microscope (TEM) and the X-ray diffraction (XRD). The electrochemical behavior of spherical nano-Ni(OH)2, attached to a graphite electrode and adjacent to an aqueous KOH-KCl electrolyte solution, has been studied by cyclic voltammetry. Spherical nano-Ni(OH)2 exhibits a pair of quasi-reversible redox peaks. The relationship of the granularity and the potential was investigated, as well as the effect of different pH conditions. Moreover, the cycling experiments have been set up using spherical nano-Ni(OH)2 and traditional analytical grade Ni(OH)2, respectively, and their cycling performances were evaluated as well. The capacity of spherical nano-Ni(OH)2 is ca. ten times higher than the one with the traditional material under the same conditions, which shows its better electrochemical properties. 相似文献
18.
无模板剂液相合成Ni(OH)2花状微球 总被引:2,自引:0,他引:2
采用一种简单的无模板剂液相合成方法制备了Ni(OH)2花状微球. 该Ni(OH)2花状微球由几十个相互连接的纳米片组成, 为α-Ni(OH)2和β-Ni(OH)2的混合晶型. 当溶液的其它条件固定时, Ni(OH)2花状微球的微观形貌随Ni(Ⅱ)浓度的变化而显著变化. 当溶液中Ni(Ⅱ)浓度为0.03 mol/L时, 花状微球粒径分布较均匀, 平均粒径约为2 μm, 微球由花瓣长度约为400 nm、厚度约为60 nm的纳米片花瓣组成. 通过观察反应过程中Ni(OH)2花状微球的微观形貌的变化, 提出了Ni(OH)2花状微球的纳米团聚-表面生长-表面溶解的形成机制. 相似文献