Corrosion Behavior of Aluminum in Non‐Uniform Electric Fields

The present paper discusses the effect of the geometrical structure of the electric fieldon the corrosion of aluminum cathodes by electrolysis of aqueous solutions of sodium chloride. A correlation between the mass of the aluminum dissolved from the cathode and the factors electric current density, distance between the electrodes, electrolysis time and sodium chloride concentration by electrolysis with direct current in electric fields of various geometries was found.     

氢氧化钠水溶液体系中金属铬的电化学氧化过程

铬铁电氧化溶出技术是一种全新的制备铬酸钠的方法,具有反应条件温和、过程可控、工艺环保等优点,然而金属铬在NaOH水溶液中的电化学氧化过程尚不明确. 本文采用循环伏安法（CV）和阳极极化法（LSV）对金属铬在NaOH水溶液中的电化学氧化过程进行研究. 使用EDS、SEM、XRD和XPS对电解前后的金属铬表征,判断中间物的产生,使用紫外可见分光光度计验证电解液中生成了铬酸钠. 结果表明,金属铬和中间产物Cr(OH)₃可能依次发生电化学氧化直接生成Na₂CrO₄,阳极极化为金属铬的活化. 随着NaOH溶液浓度的增加,Cr(OH)₃和Na₂CrO₄的生成量在增加,金属铬电化学氧化制备铬酸钠的适宜条件为碱浓度≥ 2 mol·L^-1,阳极电势≥ 1.6 V（vs. SCE）.     

Characteristics and formation of [AlO_4Al_(12)(OH)_(24)(H_2O)_(12)]~(7+) in electrolysis process

[AlO4Al12(OH)24(H2O)12] + (Al13) formation in electrolysis process is studied. The results detected by27Al NMR spectroscopy show that high content of Al13 polymer is formed in the partially hydrolyzed aluminum solution prepared by controlled electrolysis process. In the produced electrolyte of total Al concentration ([AlT]) 2.0 mol · L-1 with a basicity (B = OH/Al molar ratios) of 2.0, the content of Al13 polymer is over 60% of total Al. Dynamic light scattering shows that the size distribution of the final electrolyte solutions ([AlT] = 2.0 mol · L-1) is trimodal with B = 2.0 and bimodal with B = 2.5. The aggregates of Al13 complexes increase the particle size of partially hydrolyzed aluminum solution.     

Viscometric and Morphological Properties of Novel Magnesium Electrolyte–Polyacrylamide Composite Polymers in Aqueous Solution

The viscometric properties of novel magnesium electrolyte–polyacrylamide composite polymers in aqueous solutions were investigated using response surface methodology. Independent factors such as concentration of the magnesium electrolyte (magnesium chloride and magnesium hydroxide), concentration of polyacrylamide, and the solution temperature were taken into account for viscometric modeling. Experiments were carried out according to central composite design, which includes factorial, central and axial points of the factors. Solution viscosity was taken as the response variable. A polynomial model for the viscometric properties was developed using ANOVA and non-linear regression analysis, and the R² values are 0.9995 and 0.9996 for aqueous solutions of magnesium chloride–polyacrylamide (MCPAM) and magnesium hydroxide–polyacrylamide (MHPAM) composite polymers, respectively. Two diagnostic plots have been constructed to validate the developed models for the natural logarithm of viscosity of aqueous solutions of the MCPAM and MHPAM composite polymers. The least-squares values show that the developed models are adequate for predictive purposes. TEM was used to investigate the morphological properties of MCPAM and MHPAM composite polymers. Magnesium chloride was impregnated into the polyacrylamide chain while magnesium hydroxide was just adsorbed on the surface of the polyacrylamide chain.     

石墨电极直接电氧化合成D-阿拉伯糖

本文报道采用石墨电极直接电氧化Ｄ＿葡萄糖酸钠（ＮａＧＬ）合成Ｄ＿阿拉伯糖研究结果．研究了葡萄糖酸钠浓度、电解电压、温度及电解液组成对电流效率和合成产率的影响。同时指出采用液体电解池进行恒电位电解,其效果比恒电流电解法更好     

Chemiluminescence of luminol induced by dissolution of oxide-covered aluminum in alkaline aqueous solution

One-electron reduction of oxygen, hydrogen peroxide, potassium peroxodisulphate and potassium peroxodiphosphate was studied during the dissolution of oxide-covered aluminum in alkaline aqueous solution. The production of free oxidizing radicals was monitored by luminol chemiluminescence (CL). It was observed superoxide, hydroxyl, sulphate and phosphate radicals can be generated by the present method. In addition, luminol can be detected below nanomolar level, the linear logarithmic calibration range covering several orders of magnitude of concentration. The metallic aluminum and low-valent aluminum ions are the primary reductants of the system. The electron transfer to the solution is proposed to occur by tunneling through a thin insulating aluminum oxide film at the solid/electrolyte interface in moderately alkaline solutions with simultaneous dissolution of the forming oxide film. In a highly alkaline solution, it is more probable that the oxidation of aluminum species occurs in direct contact of the metallic aluminum with the aqueous solution. In the latter case, short-lived solvated low-valent aluminum ions, hydrogen atom and its deprotonated form, the hydrated electron, can exist as reducing mediators in the chemical reactions in the close vicinity of the dissolving solid/electrolyte interface. Luminol was also observed to exhibit CL under purely reducing conditions produced by a presently unknown excitation pathway.     

Inorganic particulates in removal of toxic heavy metal ions

The removal behavior of amorphous aluminum hydroxide for Hg(II) ions from aqueous solutions was investigated by employing a radiotracer technique at micro down to trace level concentrations. The batch type experiments were performed to obtain various physico-chemical parameters, viz., effect of sorptive concentration, temperature and pH. It was observed that the increase in sorptive concentration (from 1·10⁻⁸ to 1·10⁻² mol·dm⁻³), temperature (from 303 to 333K) and pH (from 3.4 to 10.3) apparently favored the uptake of Hg(II) by this solid. Similarly, the presence of anions (six fold) viz., oxalate, phosphate, glycine and EDTA also enhanced the uptake behavior of aluminum hydroxide for Hg(II). Whereas, the added cations viz., Na⁺, K⁺, Ba²⁺, Sr²⁺, Mg²⁺, Cd²⁺ and Fe³⁺ more or less suppressed the removal behavior of the adsorbent. Further, the adsorption process followed the classical Freundlich adsorption isotherm and deductions of various thermodynamic data revealed that the uptake of Hg(II) on aluminum hydroxide followed the ion-exchange type mechanism and thermodynamically it was found to be endothermic in nature. Part IX: Rapid and efficient removal of Hg(II) by hydrous manganese and tin oxides, J. Coll. Interf. Sci., 279 (2004) 61.     

离子液体AlCl3/Et3NHCl中电沉积法制备金属铝

在AlCl3/Et3NHCl型离子液体中铝电极上通过恒电位电解沉积制备出金属铝. 测定了不同摩尔比的AlCl3/Et3NHCl离子液体在不同温度下的电导率, 考察了离子液体AlCl3/Et3NHCl摩尔比为2/1中Al电极上铝沉积的晶核成核过程, 以及恒电位电解沉积铝的工艺条件对电流效率和沉积铝表面形貌的影响. 结果表明, 不同比例AlCl3/Et3NHCl离子液体的电导率随温度升高而升高, 符合Arrhenius规律; 在Al电极上铝沉积的成核机理为三维瞬时成核过程; 恒电位电解沉积结果表明, 室温下在电位-2.4 V(vs Pt)和电解时间20 min条件下, 沉积铝的表面形貌比较平整致密,电流效率达73%, 沉积铝的纯度达96%(w).     

Characteristics and formation of [AlO4Al12(OH)24(H2O)12]7+ in electrolysis process

[AlO₄Al₁₂(OH)₂₄(H₂O)₁₂]⁷⁺ (Al₁₃) formation in electrolysis process is studied. The results detected by²⁷Al NMR spectroscopy show that high content of Al₁₃ polymer is formed in the partially hydrolyzed aluminum solution prepared by controlled electrolysis process. In the produced electrolyte of total Al concentration ([Al_T]) 2.0 mol · L⁻¹ with a basicity (B = OH/Al molar ratios) of 2.0, the content of Al₁₃ polymer is over 60% of total Al. Dynamic light scattering shows that the size distribution of the final electrolyte solutions ([Al_T] = 2.0 mol · L⁻¹) is trimodal with B = 2.0 and bimodal with B = 2.5. The aggregates of Al₁₃ complexes increase the particle size of partially hydrolyzed aluminum solution.     

阴极冷却反应器电合成乙醛酸

以过饱和草酸水深液为阴极液 ,盐酸溶液为阳极液 ,在阴极冷却电化学反应器内草酸电解合成乙醛酸 .考察了电极温度、电解液温度、电流密度和电极材料对合成乙醛酸的时空产率和电流效率的影响 .结果表明 ,阴极冷却反应器既节省能耗 ,又可使电解过程在较高草酸浓度下进行 ,提高电流效率和时空产率 .用石墨板做阳极 ,铅做阴极 ,电流密度为 4 0 9.4 6A·m-2 ,阴极液流速 μ=1 .0 8m·s-1,电解温度为 2 0℃左右时 ,电解 3 .70h ,可得到质量分数为 3 .52 %的乙醛酸溶液 ,平均时空产率为 0 .0 3 2kg·dm-3·h     

Synthesis of aluminum oxides from the products of the rapid thermal decomposition of hydrargillite in a centrifugal flash reactor: III. Properties of aluminum hydroxides and oxides obtained via the mild rehydration of the products of the centrifugal thermal activation of hydrargillite

The interaction between the amorphous product of the centrifugal thermal activation of hydrargillite (CTA HG) and aqueous electrolytes (pH 5–11) under mild conditions (15–35°C, atmospheric pressure) has been investigated by a variety of physicochemical methods. This interaction causes material morphologic and phase changes in CTA HG, and the product composition is governed by the pH of the electrolyte and by the hydration temperature and time. The product that forms in a basic medium or water in <24 h contains up to 50% pseudoboehmite. Raising the pH or temperature or extending the hydration time results in the formation of bayerite as the major phase (～80%). An X-ray amorphous hydroxide forms in acid media. The heat treatment of this hydroxide at 550°C yields aluminum oxides differing from alumina prepared via hydroxide reprecipitation. Products with new, unusual properties can thus be obtained.     

A Study of Calcium Nitrate Purification

Two methods of calcium nitrate purification were studied: crystallization from aqueous solutions and joint precipitation of impurities from aqueous solutions onto inorganic collectors (calcium hydroxide or carbonate and hydrated aluminum or zirconium oxides). The efficiency of purification of calcium nitrate solutions was studied and the purification coefficients were calculated for hydrated aluminum or zirconium oxides as collectors.     

Leaching of Celestite in Sodium Hydroxide Solutions and Kinetic Modelling

In this study, the dissolution kinetics of celestite in solutions of sodium hydroxide was investigated by batch process. The results showed that the parameters which had the greatest effect on the dissolution of celestite in sodium hydroxide solutions were reaction temperature, the concentration of sodium hydroxide and stirring speed. It was determined that the dissolution rate increased with increased stirring speed, sodium hydroxide concentration, reaction time and temperature and decreased with increasing particle size and solid-liquid ratio. The leaching process fitted the shrinking core model with diffusion through the product layer model as the rate-determining step. The activation energy of the dissolution of celestite was calculated as 62.24?kJ/mol. A semi-empirical kinetic model was obtained for dissolution of celestite in sodium hydroxide solution.     

H型电解池中CO2电化学还原的阳极电解液问题

采用自制的H型电解池开展了KHCO₃溶液中电化学还原CO₂制甲酸的研究. 研究发现,在电解池中长时间电解时阴阳两极间的电压（槽电压）会持续升高,导致电解过程不可持续. 经过恒电位电解、恒电流电解、pH测试以及电解前后阳极室KHCO₃浓度分析等实验研究,作者发现,这是由以下过程引起的：阳极上的析氧反应产生的H⁺与电解液中的HCO₃^-反应生成水和CO₂,导致阳极室的HCO₃^-的消耗,之后阳极室的K⁺被迫扩散进入阴极室而导致阳极室电解质浓度下降. 因此,阳极室电解液导电性下降,进而引起阳极电位的升高. 研究发现,阳极电解液具有碱性时,都可能发生此种现象,因此,为了保证电解过程可持续且保持高的能量转换效率,阳极液的电解质不能是任何具有碱性的物质.     

Thermodynamic characteristics of protolytic equilibria of L-serine in aqueous solutions

The heat effects of the reaction of aqueous solution of L-serine with aqueous solutions of HNO₃ and KOH were determined by calorimetry at temperatures of 288.15, 298.15, and 308.15 K, and ionic strength values of 0.2, 0.5, and 1.0 (background electrolyte, KNO₃). Standard thermodynamic characteristics (Δ_r H ^o, Δ_r G ^o, Δ_r S ^o, ΔC _p ^o) of the acid-base reactions in aqueous solutions of L-serine were calculated. The effect of the concentration of background electrolyte and temperature on the heats of dissociation of amino acid was considered. The combustion energy of L-serine by bomb calorimetry in the medium of oxygen was determined. The standard combustion and formation enthalpies of crystalline L-serine were calculated. The heats of dissolution of crystalline L-serine in water and solutions of potassium hydroxide at 298.15 K were measured by direct calorimetry. The standard enthalpies of formation of L-serine and products of its dissociation in aqueous solution were calculated.     

Electrodeposition of Aluminum from AlCl3/Et3NHCl Ionic Liquids

Aluminum was successfully electrodeposited on Al electrodes from aluminum chloride (AlCl₃)/triethylamine hydrochloride (Et₃NHCl) ionic liquids by the constant potential electrolysis. Electrical conductivities of AlCl₃/Et₃NHCl ionic liquids were measured as a function of the temperature and composition. The nucleation processes and the influence of experimental conditions on the current efficiency and surface morphology of aluminum electrodeposits were studied on Al electrodes from 2:1 molar ratio AlCl₃/Et₃NHCl ionic liquid. The electrical conductivities of ionic liquids increased as the electrolyte temperature increased, following the Arrhenius behavior. Analyses of the chronoamperograms indicated that the deposition process of aluminum on Al substrates was controlled by instantaneous nucleation with diffusion-controlled growth. Constant potential deposition experiments showed that the electrodeposits obtained on Al electrodes were dense, continuous, and well adherent, and the current efficiency was 73% at −2.4 V(vs Pt) for 20 min electrolysis at room temperature. The purity of aluminum electrodeposits on Al electrodes was above 96% (w).     

Electrodecomposition in subcritical water using o-xylene as a model for benzene, toluene, ethylbenzene, and xylene pollutants

The possibility of the combination of electrolysis and subcritical water as a novel electrolyte was investigated. A stainless steel reactor was used as an undivided electrochemical cell containing platinum as the anode and a stainless steel reactor as the cathode. At first, the effect of temperature on the electrolysis current as the main parameter was studied in a cell containing only pure water and a supporting electrolyte. It was realized that the electrolysis current (and, consequently, the electrolysis efficiency) increased linearly with temperature because of the change in viscosity and other physicochemical properties of subcritical water. As a result, at 553 K the electrolysis efficiency was over 14-fold higher than that under ambient conditions. The possibility of the applicability of the above combined techniques for the decomposition of o-xylene was also followed as a model for benzene, toluene, ethylbenzene, and xylene (BTEX) compounds. The effect of experimental conditions such as the electrolysis duration, the electrolysis voltage, and the temperature of subcritical water was investigated. Several decomposed products were identified. o-Xylene was directly electro-oxidized to 2-methylbenzyl alcohol and consecutively to the other oxidation products. Also, hydroxide ions were oxidized to oxygen molecules, where hydrogen was generated on the cathodic surface. The final oxidation product of the electro-oxidation reaction was identified as carbon dioxide. The results indicate that more than 95% of o-xylene can be decomposed under optimum conditions.     

Electric conductivity of concentrated aqueous solutions of propionic acid, sodium propionate and their mixtures

Specific electric conductivity (EC) of concentrated aqueous solutions of propionic acid (PA), sodium propionate (SP), and water/PA/SP mixtures is measured in the temperature range of 15–90°C. Specific EC passes a maximum at the increase in the electrolyte concentration in the mixtures of water/PA, water/SP, and water/PA/SP containing a similar PA concentration. The maximum EC value of the aqueous PA solution at the given temperature is used as the generalizing term. It is shown that the values of reduced EC (ratio of EC and its maximum value at the given temperature) fall on a single curve in the whole studied range of temperatures and concentrations of the water/PA mixture. The EC activation energy is calculated for all the studied solutions. It is found that the EC activation energy of these solutions decreases at the temperature increase and grows at the increase of the concentration of electrolyte.     

A volumetric study of two related amphiphilic beta-blockers as a function of temperature and electrolyte concentration

The effects of electrolyte concentration and temperature on aqueous solutions of propranolol and acebutolol hydrochlorides have been investigated using density and ultrasound velocity measurements. The electrolyte range was 0.0–0.5 and 0.4–1.0 m for propranolol and acebutolol, respectively. For each electrolyte concentration the temperature range was 288.15–313.15 K. Critical concentrations were obtained from plots of ultrasound velocity against drug concentration. Experimental results yielded the apparent molar volume and the apparent molar adiabatic compressibility for both beta-blockers, measured over a wide concentration range. Negative deviations of the apparent molar volume from the Debye–Hückel limiting law in dilute solutions indicate the absence of premicellar aggregation. A negative slope was found for ΔV_m against temperature for both drugs. This negative value suggests that the expansibility of the surfactant in the micellar state is less than that in the aqueous phase. Changes in molar volume and adiabatic compressibility accompanying aggregate formation were smaller than those of typical surfactants, suggesting a more tightly packed aggregate.