Structure and properties of solid solutions based on bismuth niobate Bi<Subscript>3</Subscript>NbO<Subscript>7</Subscript>

Solid solutions Bi₃Nb_1–yW_yO_{7 ± δ}, Bi₃Nb_1–yV_yO_{7 ± δ}, Bi₃Nb_1–yFe_yO_{7 ± δ} (y = 0.1–0.5; Δy = 0.1), and Bi_3–xY_xNb_1–yW_yO_{7 ± δ} (x = 0.05, 0.1; y = 0–0.3; Δy = 0.1) have been studied. The homogeneity ranges of the solid solutions and crystal-chemical parameters have been determined by means of X-ray powder diffraction. The electrical conductivity of sintered samples has been studied by impedance spectroscopy. The joint introduction of yttrium and tungsten into the niobium sublattice does not lead to an increase in the conductivity of solid solutions, and the change of the dopant type has no noticeable effect on this conductivity.     

Iridium–nickel composite oxide catalysts for oxygen evolution reaction in acidic water electrolysis

A series of Ir_1–xNi_xO_2–y (0 ≤ x ≤ 0.5) composite oxides have been prepared by a simple pyrolysis method in ethanol system and used as the electrocatalysts for OER in acidic medium. The materials have been characterized by X-ray diffraction (XRD), X-ray fluorescence (XRF) and scanning electron microscopy (SEM). The electrochemical performances of these Ir_1–xNi_xO_2–y composite catalysts are evaluated by cyclic voltammetry (CV) and steady-state measurements. The resulting oxides with the Ni content (x) less than 0.3 have a complex nature of metal Ir and rutile structure IrO₂ which is similar to the Ir oxide prepared by the same approach and possess the contracted lattice resulted from the Ni-doping. Although the addition of Ni reduces the electroactive surface areas due to the coalescence of particles, the catalytic activity of the Ir_1–xNi_xO_2–y (0 < x ≤ 0.3) catalysts is slightly higher than that of the pyrolyzed Ir oxide. Regardless of the surface area difference, the intrinsic activity first increases and then decreases with the Ni content in Ir_1–xNi_xO_2–y catalysts, and the intrinsic activity of Ir_0.7Ni_0.3O_2–y catalyst is about 1.4 times of the Ni-free Ir oxide mainly attributed to the enhancement of conductivity and a change of the binding energy as increasing amount of the incorporated Ni with respect to the pure IrO₂. The Ir_0.7Ni_0.3O_2–y catalyst shows a prospect of iridium-nickel oxide materials in reducing the demand of the expensive Ir oxide catalyst for OER in acidic water electrolysis.     

Phase equilibria in the system LaMnO<Subscript>3</Subscript>-SrMnO<Subscript>3</Subscript>-SrCrO<Subscript>4</Subscript>-LaCrO<Subscript>3</Subscript>

A continuous solid solution LaMn_1?y Cr _y O₃ with an orthorhombic structure is found to exist in the range of 0.0 ≤ y ≤ 1.0. An orthorhombic solid solution La_1?x Sr _x CrO₃ exists in the range of 0.0 ≤ x ≤ 0.1. The stability boundaries are determined for the perovskite phase La_1?x Sr _x Mn_1?y Cr _y O₃. An isobaric-isothermal section LaMnO₃-SrMnO₃-SrCrO₄-LaCrO₃ of the system La₂O₃-SrO-Mn₃O₄-Cr₂O₃ in air at 1100°C is designed.     

Extraction-pyrolytic synthesis and luminescent properties of europium and terbium polytantalates

The promise of synthesis of europium and terbium polytantalates MTa _x O _y , where М = Eu, Tb; x = 7, y = 19; x = 5, y = 14; x = 3, y = 9 by low-temperature extraction-pyrolytic method has been shown. Luminescent properties of the prepared polytantalates have been assessed from excitation and luminescence spectra at 300 K. The dependence of luminescent characteristics of the studied rare earth metal polytantalates on the temperature and time of precursor pyrolysis has been established.     

Phase equilibria involving solid solutions in the Li–Mn–O system

Phase equilibria involving LiMn₂O_4-, Li₂MnO_3-, LiMnO_2-, Mn₃O_4-, and MnO-base solid solutions were studied with varied temperature and partial oxygen pressure. The \({P_{{o_2}}}\)–T and x–y projections of the P–T–x–y phase diagram of the Li–Mn?O system were constructed, as well as the key x–y isotherms of the Li₂O–MnO–MnO₂ quasi-ternary system. In some experiments, the authors’ hydride lithiation method was employed to prepare lithium-rich homogeneous three-component nonstoichiometric phases.     

Thermodynamic description of phases in the neodymium-barium-copper-oxygen system

The available experimental data were used to construct thermodynamic models of Nd-Ba-Cu-O system phases. The coordinates of the nonvariant points of this system were determined, and the phase diagram for the Nd_{1 + x} Ba_{2 ? x} Cu₃O_{6 + z} (x = 10^?4) compound was calculated.     

Nanocrystalline Calcium Carbonate Hydroxyapatites Containing Multiwall Carbon Nanotubes: Synthesis and Physicochemical Characterization

Nanocomposites (NCs) based on carbonated calcium hydroxyapatite (CHA) (bioapatite, an analogue of the inorganic component of mammalian bone tissue), carbonate apatite (Ca₁₀(PO₄)₆CO₃, CA), and multiwall carbon nanotubes (CNTs) are prepared in the system CaCl₂–(NH₄)₂HPO₄–NH₄HCO₃–NH₃–CNT–H₂O (25°C) by coprecipitation of calcium and phosphorus salts with CNTs from aqueous solutions. The physicochemical properties of nanocomposites are studied as dependent on their formation conditions and composition using the solubility (residual concentrations) method and pH measurements. The composition, crystal structure, morphology, spectroscopic and thermal characteristics of the synthesized CHA/CNT and CA/CNT NCs are determined using chemical analysis, X-ray powder diffraction, thermal analysis, and IR spectroscopy. Either CHA/CNT NCs of composition Ca₁₀(PO₄)₆(CO₃)_x(OH)_2–2х · yCNT · zH₂O, where х = 0.2; 0.5; 0.8; y = 1, 2, 3; z = 6.8–10.8, or (when х = 1) CA/CNT NCs of composition Ca₁₀(PO₄)₆CO₃ · yCNT · zH₂O, where y = 1–3; z = 6.9–10.8, are formed as the carbonate and CNT contents of the NC increase. Our results favor the understanding of the effect of carbonization and CNTs on the metabolic formation of native bone tissue apatite and can be used for the design of efficient ceramics for bone implants.     

Preparation of mesoporous Ce<Subscript>1 − <Emphasis Type="Italic">x</Emphasis></Subscript>Fe<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>O<Subscript>2</Subscript> mixed oxides and their catalytic properties in methane combustion

Mesoporous Ce_{1 ? x} Fe _x O₂ mixed oxide catalysts of different molar ratios (x = 0.1–0.5) were prepared by the citric acid sol-gel method and the microwave technique. The activities of Ce_{1 ? x} Fe _x O₂ mixed oxides on methane combustion were investigated, and the structure and reductive properties were characterized by XRD, BET, DRS, and TPR. The data showed that Ce_{1 ? x} Fe _x O₂ mixed oxides prepared were mesoporous material. When x ≤ 0.2, the transition metal Fe incorporated into the lattice of CeO₂ to form cubic Ce_{1 ? x} Fe _x O₂ solid solutions, and mixed phases of cubic Ce_{1 ? x} Fe _x O₂ solid solutions and α-Fe₂O₃ existed when x > 0.2. Ce_{1 ? x} Fe _x O₂ solid solutions show higher activity for methane combustion than pure CeO₂, especially for Ce_0.9Fe_0.1O₂.     

X-ray spectroscopy of lanthanum manganites: Nature of doping holes,correlation effects,and orbital ordering

The Mn3s X-ray photoelectron spectra of manganites were studied. It was shown that for the formal valence of manganese from 3+ to 3.3+, the doping holes are O2p in character; as the valence of manganese increases further, the Mn3d states acquire holes. For La_0.7Sr_0.3MnO₃, the Mn3p-3d resonance spectra provided information about the occupied and unoccupied Mn3d states, and the correlation energy U = 6.7 eV was determined experimentally. An analysis of X-ray dichroism on the L absorption spectra of three-dimensional La_7/8Sr_1/8MnO₃ showed that the cooperative Jahn Teller distortion of the orthorhombic phase at 240 K was related to (x ² ? z ²)/(y ² ? z ²) type orbital ordering.     

Structure and elemental composition of transparent nanocomposite silicon oxycarbonitride films

Based on thermodynamic simulation on the deposition of condensed phases with the complex composition in the Si–C–N–O–H system in a wide temperature range, using initial gas mixtures of 1,1,3,3-tetramethyldisilazane (HSi(CH₃)₂)₂NH (TMDS), TMDS with a variable mixture of oxygen and nitrogen (O₂+xN₂), a method is developed to obtain SiC _x N _y O _z :H nanocomposite films by the plasma chemical decomposition of this gas mixture in the temperature range of 373-973 K. By FTIR and energy dispersive X-ray spectroscopy the structure of chemical bonds and the elemental composition of the obtained silicon oxycarbonitride films are studied. The in situ composition of the initial gas phase in PECVD processes is examined by optical emission spectroscopy.     

Molecular Layer Deposition and Thermal Transformations of Titanium(Aluminum)-Vanadium Hybrid Organic-Inorganic Films

In this work Molecular layer deposition (MLD) technique used to synthesize titanium-vanadium (TiV _x C _y O _z ) and aluminum-vanadium (AlV _x C _y O _z ) hybrid organic-inorganic films via alternating surface reactions of titanium tetrachloride (or trimethylaluminum), vanadium oxochloride, and ethylene glycol. Using in situ monitoring it was found that the surface reactions were self-limiting at temperatures of 90 and 115°C. The coating thickness per molecular layer deposition cycle (growth rate) at 115°C on a silicon substrate varied from 5.8 to 11.4 Å/cycle, and the film densities, from 1.7 to 2.0 g cm^–3. An analysis of the samples obtained at 115°C revealed their amorphous structure. A thermal treatment of titanium-vanadium films at 450°C in air resulted in formation of highly structured coatings. These coatings were composed of nanowires of single-crystal vanadium oxide (V₂O₅) and mixed nanostructures of titanium and vanadium oxides. Increase in thermal treatment temperature to 500°C resulted in elongation of the V₂O₅ nanowires up to tens of micrometers and in their separation from the substrate. A thermal treatment of aluminum-vanadium films in air resulted in formation of a low-density film. Pyrolysis of the films in an inert gas yielded composite coatings containing domains of graphitized carbon. These films can be potentially useful in modern devices for energy storage, electronics, medicine and other promising fields of technology.     

Alkali (alkaline-earth) metal,aluminum, and titanium complex orthophosphates: Synthesis and characterization

Phase formation in the A_{1 + x} Al _x Ti_{2 ? x} P₃O₁₂ (A = Li, Na, K, Rb, or Cs; 0 ≤ x ≤ 2.0) and B_{0.5(l + x)}Al _x Ti_{2 ? x} P₃O₁₂ (B = Mg, Ca, Sr, or Ba; 0 ≤ x ≤ 2.0) systems was studied using X-ray powder diffraction, electron probe microanalysis, and IR spectroscopy. The following double and triple orthophosphates were found to exist: A_{1 + x} Al _x Ti_{2 ? x} (PO₄)₃ with A = Li (0 ≤ x ≤ 0.3), Na (0 ≤ x ≤ 1.0), K (x = 0, 1.0, or 2.0), Rb (x = 0, 1.0, or 2.0), or Cs (0 ≤ x ≤ 1.0) and B_{0.5(l + x)}Al _x Ti_{2 ? x} (PO₄)₃ with B = Mg and Ba (x = 0), Ca and Sr (0 ≤ x ≤ 0.2). These orthophosphates crystallize in the structure types of kosnarite, langbeinite, cesium titanium arsenate, potassium aluminum phosphate, or rubidium aluminum phosphate. Their crystal parameters were calculated. For CsTi₂(PO₄)₃ (x = 0), Rietveld refinement was carried out: space group Ia \(\bar 3\) d, Z = 32, a = 19.909(5) Å, V = 7892(1) ų. This compound has a framework structure. The framework is built of TiO₆ octahedra and PO₄ tetrahedra; eight- and 12-coordinated Cs⁺ cations populate interstices.     

High-temperature properties of new perovskite-like oxides

New complex oxides of composition Pr_1–y Ca _y Fe_{0.5 + x} (Mg_0.25Mo_0.25)_0.5–x O₃, 0.0 ≤ x ≤ 0.1, 0.42 ≤ y ≤ 0.8 having an orthorhombically distorted perovskite structure have been prepared. The thermal expansion and electric conductivity of the new phases have been studied in the temperature range between 100–900°C. The results of our study imply that thin films of the oxides studied can be treated as electrode materials for symmetric solid-oxide fuel cells.     

High-temperature proton conductors with structure-disordered oxygen sublattice

Data on the thermogravimetry, spectroscopy, and electrical charge transfer as functions of T, aH₂O, and aO₂ for niobates and tantalates of alkali-earth metals with structure disordering of the oxygen sublattice, which can show high-temperature proton conduction, are summarized. It is shown that in the solid solution series with decreasing x (that is, with the increasing of the oxygen vacancies concentration) the proton conductivity increase, which is caused by the increasing of both the concentration of proton defects formed in the structure (in compliance with the formula Sr_{6 ? 2x} M _{2 + 2x} ⁺⁵ O₁₀(OH)_2?6x and their mobility. The proton transfer dominates for the compositions with x < 0.15 at temperatures below 550°C. In the solid solutions (Ba_1?y Ca _y )₆Nb₂O₁₁ (0.23 ≤ y ≤ 0.47) characterized by equal concentration of oxygen vacancies, with the increasing of barium content (correspondingly, with the increasing of the lattice parameter) the oxygen-ion conductivity (at aH₂O = 3 × 10^?5) grows monotonically, which is caused by the decreasing of the oxygen atom migration energy and increasing of their mobility. In this series, the proton conductivity (at aH₂O = 2 × 10^?2) increased. It was shown, by using IR-spectroscopy and the ¹H NMR method, that the protons exist in the complex oxide structure mainly as energy-wise nonequivalent OH^? groups: isolated, closely set, and paired, whose quantitative ratios are determined by the coordination preference of the B-sublattice elements.     

Isomorphism in the KTaWO<Subscript>6</Subscript>-RbTaWO<Subscript>6</Subscript>-CsTaWO<Subscript>6</Subscript> system

Synthetic procedures have been developed and compounds of composition K _x Rb _y Cs _z TaWO₆ (x + y + z = 1) have been obtained. Their structure has been investigated by X-ray diffractometry. It has been shown that a continuous series of solid solutions is formed in the ternary system under study. Thermal decomposition of A^ITaWO₆ compounds (A^I = K, Rb, Cs) has been investigated by high-temperature X-ray diffractometry.     

Impact of poly(vinyl alcohol) adsorption on the surface characteristics of mixed oxide Mn<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>O<Subscript><Emphasis Type="Italic">y</Emphasis></Subscript>–SiO<Subscript>2</Subscript>

The poly(vinyl alcohol) (PVA) influence on the adsorption and electrokinetic properties of the mixed oxide Mn _x O _y –SiO₂/polymer solution system was examined. Three oxides differing with the Mn _x O _y contents were applied (0.2; 1 and 3 mmol/g SiO₂, respectively). The PVA with the molecular weight 100 kDa was characterized with the acetate groups content equal to 14 %. Adsorption, solid surface charge and zeta potential measurements were made as a function of solution pH (3–10). The obtained results showed that the PVA adsorption amount strongly depends on not only the solution pH, but also manganese oxide content on the mixed oxide surface. The higher solution pH value (or Mn _x O _y content) is, the higher polymer adsorption is obtained. The PVA addition to the solid suspension causes minimal changes of the mixed oxide surface charge density, whereas the zeta potential of solid particles increases significantly in the polymer presence.     

New binuclear complex of bis(2,4,6,8-tetramethyl-2,4,6,8- tetraazabicyclo(3.3.0)octane-3,7-dione-<Emphasis Type="Italic">O,O</Emphasis>')-diaquatetrakis(nitrato-<Emphasis Type="Italic">O,O</Emphasis>')-dimanganese(II) monohydrate: Synthesis and crystal structure

The centrosymmetric binuclear manganese(II) nitrate complex with a bicyclic bis-carbamide, namely, 2,4,6,8-tetramethyl-2,4,6,8-tetraazabicyclo(3.3.0)octane-3,7-dione, or mebicar (Mk) [Mn(C₈H₁₄N₄O₂)(H₂O)(NO₃)₂]₂ · H₂O (I), has been synthesized for the first time. The structure of complex I has been solved (CCDC no. 1435139). Crystals of complex I are monoclinic, space group P2₁/c, a = 12.8108(11) Å, _b = 10.0662(2) Å, c = 18.6367(17) Å, β = 136.512(16)°, V = 1654.0(4) ų, ρcalcd = 1.659 g/cm³, Z = 2. Each manganese atom is coordinated to the two oxygen atoms of two Mk molecules related by the symmetry codes (1–x, 2–y, 1–z) and to two bidentate nitrate anions and one water molecule. The coordination polyhedron of the manganese atom is a strongly distorted pentagonal bipyramid. The Mn···Mn distance in the complex is 8.7261(9) Å.     

Enhanced lithium-ion intercalation and conduction of transparent tantalum oxide films by lithium addition with an atmospheric pressure plasma jet

An investigation is conducted on enhancing lithium-ion intercalation and conduction performance of transparent organo tantalum oxide (TaO _y C _z ) films, by addition of lithium via a fast co-synthesis onto 40 Ω/□ flexible polyethylene terephthalate/indium tin oxide substrates at the short exposed durations of 33–34 s, using an atmospheric pressure plasma jet (APPJ) at various mixed concentrations of tantalum ethoxide [Ta(OC₂H₅)₅] and lithium tert-butoxide [(CH₃)₃COLi] precursors. Transparent organo-lithiated tantalum oxide (Li _x TaO _y C _z ) films expose noteworthy Li⁺ ion intercalation and conduction performance for 200 cycles of reversible Li⁺ ion intercalation and deintercalation in a 1 M LiClO₄-propylene carbonate electrolyte, by switching measurements with a potential sweep from ?1.25 to 1.25 V at a scan rate of 50 mV/s and a potential step at ?1.25 and 1.25 V, even after being bent 360° around a 2.5-cm diameter rod for 1000 cycles. The Li⁺ ionic diffusion coefficient and conductivity of 6.2?×?10^?10 cm²/s and 6.0?×?10^?11 S/cm for TaO _y C _z films are greatly progressed of up to 9.6?×?10^?10 cm²/s and 7.8?×?10^?9 S/cm for Li _x TaO _y C _z films by co-synthesis with an APPJ.     

Mechanochemical synthesis of colloidal silver bromide particles in the NaBr–AgNO<Subscript>3</Subscript>–NaNO<Subscript>3</Subscript> system

X-ray diffraction and thermal analyses, electron microscopy, and dynamic light scattering have been employed to study silver bromide nanoparticles obtained by the mechanochemical exchange reaction NaBr + AgNO₃ + zNaNO₃ = (z + 1)NaNO₃ + AgBr in sodium nitrate matrix (diluent and side reaction product) at z = z₁ = 8.06 and z = z₂ = 4.31. AgBr nanoparticles have been obtained in the free form by dissolving the matrix in water, and their activity in the photodegradation of methylene blue dye has been studied.