Crystalline structure and morphology of biaxially oriented polyamide‐11 films

The effect of the uniaxial and biaxial stretching and subsequent solution annealing of extrusion‐cast polyamide‐11 films on the crystalline structure and morphology was investigated with differential scanning calorimetry, wide‐angle X‐ray diffraction (WAXD), Fourier transform infrared spectroscopy, and small‐angle X‐ray scattering (SAXS). The extrusion‐cast polyamide‐11 films exhibited elevations in the glass‐transition and cold‐crystallization temperatures with a constant crystallinity and a constant melting point during aging under room conditions (20–26 °C and 20–31% relative humidity). WAXD and SAXS suggested that chain‐folded lamellae of coexisting α‐ and β‐crystals existed in all the stretched polyamide‐11 films. WAXD pole figures indicated that hydrogen bonds in the hydrogen‐bonded sheets of these two crystalline forms apparently formed between antiparallel chain molecules. The unit cell parameters [a = 9.52 Å, b = 5.35 Å, c = 14.90 Å (chain axis), α = 48.5°, β = 90°, and γ = 74.7° for a triclinic α form and a = 9.52 Å, b = 14.90 Å (chain axis), c = 4.00 Å, α = 90°, β = 67.5°, and γ = 90° for a monoclinic β form] for polyamide‐11 crystals were proposed according to the results of this study and the results of previous investigators. The unit cell parameters of the stretched extrusion‐cast polyamide‐11 films varied, depending on the stretching conditions (the stretch temperature and stretch ratio). As the stretch temperature and stretch ratio were increased, the crystal became more similar to the form described previously and was accompanied by an increase in the long spacing of crystalline lamellae. Annealing the stretched films in a boiling 20% formic acid solution made slightly more perfected crystals. The hydrogen‐bonding α(010) + β(002) planes, which are nearly parallel to both amide group planes and zigzag methylene sequence planes of the biaxially stretched films were found to be parallel to the film surface. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2624–2640, 2002     

Layer structure estimation of three‐dimensional crystal and two‐dimensional molecular film for fluorinated comb copolymers

Comb copolymers containing both hydrogenated and fluorinated side‐chains were prepared by copolymerization using acrylic or methacrylic monomers in several ratios. The crystal structures of these copolymers and layer structures of their organized molecular films were investigated by wide‐angle X‐ray diffraction (WAXD), small‐angle X‐ray scattering (SAXS), and out‐of plane X‐ray diffraction. Further, to selectively estimate the regularity of shorter fluorocarbon side‐chains, organized molecular films of copolymers were investigated by polarized near‐edge X‐ray adsorption fine structure (NEXAFS) spectroscopy. From the results of these measurements, it was inferred that these copolymers formed highly ordered layer structures, and a long spacing was predominantly determined by the arrangement of hydrogenated side‐chains, except in copolymers having extremely high fluorocarbon contents. In the case of the organized molecular films, the fluorinated side‐chains of methacrylate copolymers cannot form a highly ordered arrangement, whereas those of acrylate copolymers were oriented on monolayers. However, in both cases, the hydrogenated side‐chains predominantly formed layer structures in the organized films, and the fluorinated side‐chains did not contribute to the formation of the layer structures. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 534–546, 2008     

Morphology and structure of nylon‐2,14 single crystals from dilute solution

A perfect single crystal of nylon‐2,14 was prepared from 0.02% (w/v) 1,4‐butanediol solution by a “self‐seeding” technique and isothermal crystallization at 120 and 145 °C. The morphology and structure features were examined by transmission electron microscopy with both image and diffraction modes, atomic force microscopy, and wide‐angle X‐ray diffraction (WAXD). The nylon‐2,14 single crystal grown from 1,4‐butanediol at 145 °C inhabited a lathlike shape with a lamellar thickness of about 9 nm. Electron diffraction and WAXD data indicated that nylon‐2,14 crystallized in a triclinic system with lattice dimensions a = 0.49 nm, b = 0.51 nm, c = 2.23 nm, α = 60.4°, β = 77°, and γ = 59°. The crystal structure is different from that of nylon‐6,6 but similar to that of other members of nylon‐2Y. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1913–1918, 2002     

Crystallization behavior of isotactic propylene‐1‐hexene random copolymer revealed by time‐resolved SAXS/WAXD techniques

The crystallization behavior of isotactic propylene‐1‐hexene (PH) random copolymer having 5.7% mole fraction of hexene content was investigated using simultaneous time‐resolved small‐angle X‐ray scattering (SAXS) and wide‐angle X‐ray diffraction (WAXD) techniques. For this copolymer, the hexene component cannot be incorporated into the unit cell structure of isotactic polypropylene (iPP). Only α‐phase crystal form of iPP was observed when samples were melt crystallized at temperatures of 40 °C, 60 °C, 80 °C, and 100 °C. Comprehensive analysis of SAXS and WAXD profiles indicated that the crystalline morphology is correlated with crystallization temperature. At high temperatures (e.g., 100 °C) the dominant morphology is the lamellar structure; while at low temperatures (e.g., 40 °C) only highly disordered small crystal blocks can be formed. These morphologies are kinetically controlled. Under a small degree of supercooling (the corresponding iPP crystallization rate is slow), a segmental segregation between iPP and hexene components probably takes place, leading to the formation of iPP lamellar crystals with a higher degree of order. In contrast, under a large degree of supercooling (the corresponding iPP crystallization rate is fast), defective small crystal blocks are favored due to the large thermodynamic driving force and low chain mobility. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 26–32, 2010     

Crystallization and chain conformation of semicrystalline and amorphous polymer blends studied by wide‐angle and small‐angle scattering

We examine the crystallization and chain conformation behavior of semicrystalline poly(ethylene oxide) (PEO) and amorphous poly(vinyl acetate) (PVAc) mixtures with wide‐angle X‐ray diffraction (WAXD), small‐angle X‐ray scattering (SAXS), and small‐angle neutron scattering (SANS) experiments. For blends with PEO weight fractions (wt_PEO) greater than or equal to 0.3, below the melting point of PEO, the WAXD patterns reveal that crystalline PEO belongs to the monoclinic system. The unit‐cell parameters are independent of wt_PEO. However, the bulk crystallinity determined from WAXD decreases as wt_PEO decreases. The scattered intensities from SAXS experiments show that the systems form an ordered crystalline/amorphous lamellar structure. In a combination of WAXD and SAXS analysis, the related morphological parameters are assigned correctly. With the addition of amorphous PVAc, both the average amorphous layer thickness and long spacing increase, whereas the average crystalline layer thickness decreases. We find that a two‐phase analysis of the correlation function from SAXS, in which the scattering invariant is linearly proportional to the volume fraction of lamellar stacks, describes quantitatively the crystallization behavior of PEO in the presence of PVAc. When wt_PEO is close to 1, the samples are fully spaced‐filled with lamellar stacks. As wt_PEO decreases from 1.0 to 0.3, more PVAc chains are excluded from the interlamellar region into the interfibrillar region. The fraction outside the lamellar stacks, which is completely occupied with PVAc chains, increases from 0 to 58%. Because the radius of gyration of PVAc with a random‐coil configuration determined from SANS is smaller than the average amorphous layer thickness from SAXS, we believe that the amorphous PVAc chains still persist with a random‐coil configuration even when the blends form an ordered structure. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2705–2715, 2001     

Multiaxial deformation of polyethylene and polyethylene/clay nanocomposites: in situ synchrotron small angle and wide angle X‐ray scattering study

A unique in situ multiaxial deformation device has been designed and built specifically for simultaneous synchrotron small angle X‐ray scattering (SAXS) and wide angle X‐ray scattering (WAXS) measurements. SAXS and WAXS patterns of high‐density polyethylene (HDPE) and HDPE/clay nanocomposites were measured in real time during in situ multiaxial deformation at room temperature and at 55 °C. It was observed that the morphological evolution of polyethylene is affected by the existence of clay platelets as well as the deformation temperature and strain rate. Martensitic transformation of orthorhombic into monoclinic crystal phases was observed under strain in HDPE, which is delayed and hindered in the presence of clay nanoplatelets. From the SAXS measurements, it was observed that the thickness of the interlamellar amorphous region increased with increasing strain, which is due to elongation of the amorphous chains. The increase in amorphous layer thickness is slightly higher for the nanocomposites compared to the neat polymer. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Morphology and crystal structure of the poly(ethylene oxide)–hydroquinone molecular complex

The occurrence of a molecular complex between poly(ethylene oxide) (PEO) and p‐dihydroxybenzene (hydroquinone) has been determined using different experimental techniques such as differential scanning calorimetry (DSC), wide‐angle X‐ray diffraction (WAXD), and Fourier transform infrared spectroscopy (FTIR). From DSC investigations, an ethylene oxide/hydroquinone molar ratio of 2/1 was deduced. During the heating, the molecular complex undergoes a peritectic reaction and spontaneously transforms into a liquid phase and crystalline hydroquinone (incongruent melting). A triclinic unit cell (a = 1.17 nm, b = 1.20 nm, c = 1.06 nm, α = 78°, β = 64°, γ = 115°), containing eight ethylene oxide (EO) monomers and four hydroquinone molecules, has been determined from the analysis of the X‐ray diffraction fiber patterns of stretched and spherulitic films. The PEO chains adopt a helical conformation with four monomers per turn, which is very similar to the 7₂ helix of the pure polymer. A crystal structure is proposed on the basis of molecular packing considerations and X‐ray diffraction intensities. It consists of a layered structure with an alternation of PEO and small molecules layers, both layers being stabilized by an array of hydrogen bonds. The morphology of PEO–HYD crystals was studied by small angle X‐ray scattering and DSC. As previously shown for the PEO–resorcinol complex, PEO–HYD samples crystallize with a lamellar thickness corresponding to fully extended or integral folded chains. The relative proportion of lamellae with different thicknesses depends on the crystallization temperature and time. Finally, the observed morphologies are discussed in terms of intermolecular interactions and chain mobility. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1197–1208, 1999     

Crystal forms and ferroelectric properties of poly(vinylidene fluoride)/polyamide 11 blends prepared by high‐shear processing

Nanostructured poly(vinylidene fluoride) (PVDF)/polyamide 11 (PA11) blends have been melt‐processed using a high‐shear extruder. Uniaxially oriented blended films were fabricated by hot rolling to prepare ferroelectic films. The effects of rolling temperature and draw ratio on the crystal forms of both PVDF and PA 11 were investigated by means of Fourier transform infrared spectra (FTIR) and wide‐angle X‐ray diffraction (WAXD). It was shown that hot rolling in the range of 25–110 °C results in the crystal form transformation from the nonpolar α‐form into the polar β‐form for PVDF. The content and orientation function of β‐crystallites are strongly dependent upon the rolling temperature and the draw ratio. The highest content of well‐oriented β‐crystallites was achieved with a draw ratio of 4.0 upon rolling at 80 °C. At the same time, the content of the α‐form of PA11 in the blend was also found to decrease by hot rolling. The ferroelectric properties (D‐E hysteresis) of the oriented blended films were measured. The remanent polarization of the PVDF/PA11 = 90/10 blend is as high as 91 mC/m², which is about 1.2 times higher than that of pure PVDF. The D‐E hysteresis curves and the temperature dependence of the piezoelectric stress coefficients of the high‐shear‐processed sample suggested that the formation of nano‐dispersed structures resulted in the improvement of the remanent polarization and thermal characteristics at a temperature higher than 80 °C. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2707–2714, 2007     

Structure development in multistage stretching of PTFE films

The structure of expanded poly(tetrafluoroethylene) (ePTFE) films that were produced by uniaxial or biaxial stretching of a calendared sheet were studied by wide angle X‐ray diffraction (WAXD), small angle X‐ray scattering, differential scanning calorimetry (DSC), and scanning electron microscopy. The molecular orientation of the stretched films was analyzed by WAXD flat films and pole figures. Biaxial orientation factors were computed to interpret the level of orientation quantitatively. DSC scans showed that oriented samples exhibited two melting peaks, one at the commonly observed temperature in the range 340–345 °C and one around 380 °C. The possible causes of this high‐temperature melting peak and its relation to previously described processes is discussed. The microporous nature of the ePTFE films is also briefly discussed. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Effects of spacing between the exfoliated clay platelets on the crystallization behavior of polyamide‐6 in polyamide‐6/clay nanocomposites

Exfoliated polyamide‐6 (PA6)/organoclay nanocomposite films with planar‐oriented clay platelets were prepared by the simple hot pressing of melt‐extruded nanocomposite pellets. The average distance between the neighboring clay platelets was controlled by changes in the clay loading content in the nanocomposites. The effects of the clay platelet spacing on the crystallization behavior of PA6 were investigated with transmission electron microscopy and wide‐angle X‐ray diffraction. The crystal lamellae were found to be mainly perpendicular to the clay surface for the nanocomposites with large spacing between the clay sheets at low clay loading contents. This perpendicular orientation morphology was attributed to the strong interactions between the PA6 molecular chain and the clay surface. In contrast, the crystal lamellae were found to be parallel to the clay surface when the spacing between the neighboring clay platelets was less than 30 nm. It was concluded that the confinement crystallization of PA6 within the nanoscale channels formed by clay sheets resulted in this parallel orientation texture. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 284–290, 2006     

Morphology development during isothermal crystallization. II. Isotactic and syndiotactic polypropylene blends

Morphology development during isothermal crystallization in equal molecular weight isotactic polypropylene (iPP), syndiotactic polypropylene (sPP), and iPP/sPP blends was studied with time‐resolved simultaneous small‐angle X‐ray scattering (SAXS) and wide‐angle X‐ray diffraction (WAXD) with synchrotron radiation. The sPP melting point is 15–20 °C below that of the iPP component, and sPP multiple melting is not affected by blending for 50–100 wt % sPP compositions. SAXS and WAXD (at 115 and 137.5 °C) show that sPP crystallizes more slowly than iPP. The sPP long spacing is larger than that of iPP at both crystallization temperatures, exhibits a broader distribution, and changes to a greater extent during crystallization. Differential scanning calorimetry (DSC) cooling and SAXS/WAXD measurements show iPP crystallizing first and nearly to completion before sPP in a 50:50 iPP/sPP blend. At 115 °C, iPP crystals nucleate sPP in a 50:50 blend and modify the sPP lamellar spacing. The nucleation does not overcome the large difference in the iPP and sPP rates at 137.5 °C. Before sPP crystallization in a 50:50 blend (115 °C), the iPP long spacing is not affected by molten sPP. The iPP long spacing is slightly expanded by molten sPP, and the WAXD induction time is delayed at 137.5 °C. The observed iPP long spacing in the presence of molten sPP is consistent with previously reported results for iPP/atactic polypropylene (aPP) blends of similar molecular weight. Quantitative differences between the two types of blends are consistent with previously reported thermodynamic rankings. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1876–1888, 2001     

The influence of short chain branch on formation of shish‐kebab crystals in bimodal polyethylene under shear at high temperatures

Formation of shish‐kebab crystals due to the coil–stretch transition under shear in the molten state using a bimodal polyethylene system with high molecular weight (HMW) fraction having different branch content was investigated. In specific, in situ small‐angle X‐ray scattering (SAXS) and wide‐angle X‐ray diffraction (WAXD) techniques were used to study the structure evolution of shish‐kebab crystals at high temperatures under simple shear. The SAXS results revealed that with the increase of branch content, shish‐kebab crystals became more stable at high temperatures (e.g., 139 °C). However, the shish length of the bimodal PE containing 0.11% branch was shorter than that with no branch. The WAXD results showed that the degree of crystallization for bimodal PE with HMW fraction having 0.11% branch increased with time but reached a plateau value of 1%, while that with no branch increased continuously till 11%. Furthermore, the crystal orientation of bimodal PE with HMW fraction having 0.11% branch was above 0.9 and maintained at a constant value, while that with no branch decreased from 0.9 to 0.1 upon relaxation. This study indicates that even though the crystallizability of the HMW fraction with branch content decreased, they could effectively stabilize the shear‐induced crystalline structure with shorter shish‐kebab crystals. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 786–794     

Oriented crystallization of poly(L‐lactic acid) in uniaxially oriented blends with poly(vinylidene fluoride)

This article describes the oriented crystallization of poly(L ‐lactic acid) (PLLA) in uniaxially oriented blends with poly(vinylidene fluoride) (PVDF). Uniaxially drawn films of PLLA/PVDF blend with fixed ends were heat‐treated in two ways to crystallize PLLA in oriented blend films. The crystal orientation of PLLA depended upon the heat‐treatment process. The crystal c‐axis of the α form crystal of PLLA was highly oriented in the drawing direction in a sample cold‐crystallized at T_c = 120 °C, whereas the tilt‐orientation of the [200]/ [110] axes of PLLA was induced in the sample crystallized at T_c = 120 °C after preheating at T_p = 164.5–168.5 °C. Detailed analysis of the wide‐angle X‐ray diffraction (WAXD) indicated that the [020]/ [310] crystal axes were oriented parallel to the drawing direction, which causes the tilt‐orientation of the [200]/ [110] axes and other crystal axes. Scanning electron microscopy (SEM) suggested that oriented crystallization occurs in the stretched domains of PLLA with diameters of 0.5–2.0 μm in the uniaxially drawn films of PVDF/PLLA = 90/10 blend. Although the mechanism for the oriented crystallization of PLLA was not clear, a possibility was heteroepitaxy of the [200]/[110] axes of the α form crystal of PLLA along the [201]/[111] axes of the β form crystal of PVDF that is induced by lattice matching of d₁₀₀(PLLA) ≈ 5d₂₀₁(PVDF). © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1376–1389, 2008     

Simultaneous wide‐angle X‐ray diffraction and differential scanning calorimetry analysis of the melting and recrystallization behavior of polyethylene and isotactic polypropylene containing cyclopentane units in the main chain

The melting and crystallization behavior of polyethylene and isotactic polypropylene containing 1,2‐ or 1,3‐disubstituted cyclopentane units in the main chain has been studied with simultaneous wide‐angle X‐ray diffraction (WAXD) and differential scanning calorimetry. For the ethylene‐based copolymers, the position of a reflection peak in the WAXD patterns shifts to a low angle with the increasing acquired temperature. The temperature dependence on the axial length of the crystal lattice is more marked in the copolymers forming orthorhombic crystals (containing 1,2‐cyclopentane or 5.6 mol % 1,3‐cyclopentane units) than in those forming hexagonal crystals (containing 8.1 mol % 1,3‐cyclopentane units). For the isotactic propylene‐based copolymers, the position of the reflection peaks in the WAXD patterns is independent of the acquired temperature. The proportion of the γ form in the copolymer containing the 1,2‐cyclopentane units is higher than that in the copolymers containing the 1,3‐cyclopentane units. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1457–1465, 2004     

Crystalline structure of polyamide 12 as revealed by solid‐state 13C NMR and synchrotron WAXS and SAXS

The crystalline structure of polyamide‐12 (PA12) was studied by solid‐state ¹³C nuclear magnetic resonance (NMR) as well as by synchrotron wide‐ and small‐angle X‐ray scattering (WAXS and SAXS). Isotropic and oriented PA12 showed different NMR spectra ascribed to γ‐ and γ′‐crystalline modifications, respectively. On the basis of the position of the first diffraction peak, the isotropic γ‐form and the oriented γ′‐form were shown to be with hexagonal crystalline lattice at room temperature. When heated, the two PA12 polymorphs demonstrated different behaviors. Above 140 °C, the isotropic γ‐PA12 partially transformed into α‐modification. No such transition was observed with the oriented γ′‐PA12 phase even after annealing at temperatures close to melting. A γ′–γ transition was observed here only after isotropization by melting point. Various structural parameters were extracted from the WAXS and SAXS patterns and analyzed as a function of temperature and orientation: the degree of crystallinity, the d‐spacings, the Bragg's long spacings, the average thicknesses of the crystalline (l_c) and amorphous (l_a) phases, and the linear crystallinity x_cl within the lamellar stacks. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3720–3733, 2005     

Integrated mechanism for the morphological structure development in HDPE melt‐blown and machine‐direction‐oriented films

The morphologies of a series of blown films and machine‐direction‐oriented (MDO) films, all produced from high density polyethylene, were characterized. In the blown film process, the crystalline morphology develops while the melt is under extensional stress. In the MDO process, drawing takes place in the solid state and deforms the crystalline morphology of the starting film. The films were characterized by wide‐angle X‐ray scattering (WAXS), small‐angle X‐ray scattering (SAXS) and atomic force microscopy to determine the lamellar morphology. The effect of the type of deformation on the lamellar morphology was studied and relationships were developed between the lamellar and polymer chain morphology using SAXS and WAXS. Blown and MDO films were found to have very different morphologies. However, an integrated mechanism was developed linking the sequential events in the deformation and morphology development in blown and MDO films. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1834–1844, 2007     

Morphology and orientation during the deformation of segmented elastomers studied with small‐angle X‐ray scattering and atomic force microscopy

Small‐angle X‐ray scattering (SAXS), atomic force microscopy (AFM), and other techniques were combined in a study of segmented thermoplastic elastomers (Pebax) containing poly(tetramethylene oxide) soft segments and hard blocks of nylon‐12. AFM was used to provide real‐space resolution of the morphology during tensile elongation and after subsequent relaxation. Nanofibril formation, starting at strains of about 1.5×, was characterized in detail, showing the evolution of the number, orientation, and size of these highly stressed load‐bearing fibrils that dominated the mechanical properties. AFM results were combined with two‐dimensional SAXS data to develop a model considering the breakup of the original ribbonlike nylon‐12 lamellae in combination with progressive reformation and orientation of highly stressed fibrils. The complex changes in the two‐dimensional SAXS images included a distorted arc pattern due to increased spacing of the lamellae in the stretch direction at low strains, with an evolution to completely different patterns dominated mainly by intrafibrillar and interfibrillar scattering contributions. Between stretch ratios of 1.5 and 2.3× original lamellae were progressively broken up, and by 3.2×, all lamellae independent of the initial orientation were broken into smaller crystals with low aspect ratios. The results were combined with differential scanning calorimetry and birefringence data taken on films under strain to obtain insight into the microscopic basis for strain softening and plastic deformation in Pebax and related segmented polymers. Birefringence cycling with strain provided a consistent picture with the other techniques for understanding the redistribution of stress on a nanoscopic scale during deformation and relaxation. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1727–1740, 2002     

Structure and properties of polyimide fibers containing benzimidazole and Amide Units

Co‐polyimide (co‐PI) fibers with outstanding mechanical properties were fabricated via thermal imidization of polyamic acids, derived from a new design of combining the amide and benzimidazole diamine monomers, 4‐amino‐N‐(4‐aminophenyl)benzamide (DABA) and 2‐(4‐aminophenyl)‐5‐aminobenzimidazole (BIA), with 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA). The crystalline structure and micromorphology of the prepared co‐PI fibers were investigated by synchrotron wide‐angle X‐ray diffraction (WAXD) and small‐angle X‐ray scattering (SAXS). The two‐dimensional WAXD spectra imply that the co‐PI fibers possess a structure between smectic‐like and three‐dimensionally ordered crystalline phase, and all the obtained fibers are highly oriented along the fiber axis. SAXS patterns exhibit a pair of meridional scattering streaks for the homo‐PI (BPDA/BIA) fiber, suggesting the presence of periodic lamellar structure. The incorporation of DABA into the polymer chains destroyed the lamellar structure but led to smaller size of microvoids upon increasing DABA moiety, based on SAXS analysis. The co‐PI fibers, with the molar ratio of BIA/DABA being 7/3, exhibited the optimum tensile strength and modulus of 1.96 and 108.3 GPa, respectively, attributed to the well‐defined ordered and dense structure. The chemical structure and molecular packing significantly affected the thermal stability of fibers, resulting in the different glass transition temperatures (T_g) from 350 to 380 °C. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 183–191     

Lamellar cluster structure formation resulting from interchain interaction in a novel aromatic polyimide based on PMDA monomer

The aggregation structure of a novel polyimide ( PIM ‐ 6 ) with six methylene flexible spacing groups in biphenyl side chain synthesized by the traditional two‐step imidisation process was investigated by polarized light microscope (PLM), small angle X‐ray scattering (SAXS), wide angle X‐ray scattering (WAXS), and molecular simulation approach. The agreement between the experimental data and simulation result reveals that due to the predominant interchain interaction, each three backbones stack together to form a distinct lamellar cluster with side chains packed inside dispersedly. The thickness of the lamellar cluster is about 16.0 A°, corresponding to a strong peak at 5.5° in SAXS pattern. As the backbone is not perfectly parallel to each other in each lamellar cluster, the distance between each backbone ranges from 5.8 to 8.8 A° possibly relating to the weak peak at 9.8° in WAXS pattern. Meanwhile, no birefringence or apparent phase texture has been observed by PLM indicating an amorphous nature in this film. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Phase transition in polyamide‐66/montmorillonite nanocomposites on annealing

The crystalline‐phase transition in polyamide‐66/montmorillonite nanocomposites before melting was investigated by in situ X‐ray diffraction and is reported for the first time in this work. The phase‐transition temperature in the nanocomposites was 170 °C, 20 °C lower than that in polyamide‐66. The lower phase‐transition temperature of the nanocomposites could be attributed to the γ‐phase‐favorable environment caused by silicate layers. Meanwhile, the addition of silicate layers changed the crystal structure of the polyamide‐66 matrix and influenced the phase‐transition behavior. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 63–67, 2003