同步扫描-双波长荧光分光光度法同时测定三种儿茶酚胺类神经递质

提出了用同步扫描-双波长荧光分光光度法同时测定肾上腺素(EP)、去甲肾上腺素素(NEP)和多巴胺(DA)3种儿茶酚胺类神经递质.试验表明:荧光检测宜选定发射波长(λen)与激发波长(λex)的波长差为70 nm(△λ=λem-λex)的条件下进行同步扫描.在λem为385.0 nm时DA的荧光信号不受EP和NEP的干扰,而EP和NEP相互的干扰,采用双波长荧光检测模式可消除.选择测定NEP的波长对为470.0 nm(λem,1)和531.8 nm(λem,2),测定EP的波长对为500.0 nm(λ'em,1)和445.6 nm(λ'em,2).测得荧光强度与3种儿茶酚胺浓度在320 μg·L-1(EP),640 μg·L-1(NEP)及160μg·L-1(DA)内呈线性关系,检出限(3σ/k)依次为0.20,0.97,0.73 μg·L-1.     

5-(4-硝基苯偶氮)-8-(4-甲苯磺酰氨基)-喹啉的合成及在钴的测定中的应用研究

首次合成了5-(4-硝基苯偶氮)-8-(4-甲苯磺酰氨基)-喹啉,测量了其酸离解常数。在非离子型表面活性剂存在下,试剂与钴(Ⅱ)在pH9.0～11.2范围内形成配合物,ε_(645)=1.01×10~5L·mol~(-1)cm~(-1),在H_2o_2作用下,于λ_((?)m)/λ_((?)x)=420nm/345nm产生强荧光,建立了一个操作简便快速、灵敏度高、选择性好的荧光分析新方法,线性范围2～32ppb,检测极限0.1ngCo(Ⅱ)/ml,用以测量了维生素B_(12)及生物样品中的痕量钴(Ⅱ)。探讨了H_2O_2对荧光增敏的机理。     

手性荧光衍生化反相高效液相色谱法分析多巴胺

以R(-)_4_(N,N_Dimethylaminosulfonyl)_7_(3_isothiocyanatopyrrolidino)_2,1,3_benzoxadiazole(R(-)_DBD_PyNCS)作为手性荧光衍生化试剂, 用反相高效液相色谱法(RP-HPLC)定量分析多巴胺。衍生化反应是在含有7%吡啶溶剂中, 75 ℃温度条件下, 进行40 min, 生成具有荧光特性的多巴胺衍生物(λex= 460 nm, λem= 550nm)。生成的衍生物在流动相为乙腈-水(体积比35∶65), 流速为1.0 mL/min, 在DiamonsilTM C18(150 mm×4.6mm, i.d., 5μm)色谱柱上保留时间约为15 min。多巴胺衍生物在60~1 200 ng/mL时与峰面积呈良好的线性关系(r=0.999 6), 多巴胺浓度为1 mmol/L时, 峰面积测定结果的相对标准偏差(RSD)为2.4%, 检出限为12 ng/L(S/N=3)。检测了盐酸多巴胺注射液中多巴胺的含量。     

牛血清白蛋白中氨基酸的高效液相色谱荧光测定及质谱鉴定

利用新型荧光试剂1,2苯-并-3,4二-氢咔唑-9乙-基氯甲酸酯(BCEOC)作为柱前衍生化试剂,在Hypersil BDS C18(4.6 mm×200 mm,5μm)反相色谱柱上,采用梯度洗脱对氨基酸衍生物进行了分离检测。检测的激发和发射波长分别为λex=333 nm,λem=390 nm。采用电喷雾离子源(ESI Source),实现了牛血清白蛋白中氨基酸的定性测定。荧光定量检测的线性回归系数均大于0.999;检出限为6.3~117.6 fmo。l     

4,5-二溴苯基荧光酮-溴化十六烷基三甲铵荧光熄灭法测定微量铁

本文利用DBPF为荧光试剂,在大量CTMAB存在下,用荧光熄灭法测定微量铁,λ_(ex)为362nm,λ_(em)560nm。线性范围为0.002～0.12μg/mL。三元络合物中,Fe:DBPF=1:3。     

直接荧光光度法测定水中痕量酚

建立了一种新的荧光光度法分析水中痕量酚.水中的酚经紫外光照射后,激发强荧光λ_(ex)=273nm,λ_(em)=302nm),能直接进行荧光光度测定.检出限0.03μg·L~(-1),相对标准偏差0.29%,回收率97.5%～102.5%.方法简单、快速、精密度和准确度高、无毒、安全.     

荧光光度法测定痕量钯(Ⅱ)

本文报道了钯(Ⅰ)-邻菲啰啉-乙基曙红荧光熄灭间接法测定痕量钯(Ⅰ)的新方法,要pH5.6时配合物λ_(ex)=524nm,λ_(em)=542nm,钯含量在0-20μg/25ml范围内有良好的线性关系,灵敏度高(检测下限为0.04μg/ml),本法成功的应用于含钯废水中钯的测定。     

微波溶样肉桂基荧光酮和表面活性剂连续荧光测定葡萄酒中铁和钴

观察到肉桂基荧光酮(略作CF)在pH≈8与Fc(Ⅲ)配位后荧光增强,CPB的加入使荧光更强,络合物与试剂荧光强度之比F_(FeR)/F_R随0～0.01μg/ml Fe(Ⅲ)线性变化,λ_(ex)=410nm,λ_(ex)=480nm;而CF在pH≈10与Co(Ⅲ)配位后荧光却减弱,乳化剂OP存在时使试剂荧光增强,若以荧光熄灭Co(Ⅲ)灵敏度便提高,试剂与络合物荧光强度之比F_R/F_(CoR)对0～0.016 μg/ml Co(Ⅲ)呈直线关系,λ_(ex)=300nm,L_(em)=352nm。控制化学条件和激发、发射波长,可不经分离测定葡萄酒(微波溶样)中铁和钴。     

多目标单纯形法在茜素红催化荧光测定痕量钒(V)中的应用

本文建立了茜素红催化荧光测定痕量钒(V)的新方法.在λ_(ex)/λ_(em)=381/445(nm),由多目标罚函数单纯形法获得最佳实验条件为:1%茜素红6mL,1mol/L盐酸2.1mL,饱和KIO_4,1.8mL,反应温度85℃,反应时间15.30min,钒的检测下限为7×10~(-10)g/mL,反应对试剂及金属离子均为一级反应.方法用于水样和铬钒钢中钒的测定,结果满意.     

铈(Ⅳ)-L-酪氨酸的荧光光度法的研究及应用

本文提出了以L-酪氨酸为荧光剂测定铈的方法。其荧光物质的λ_(ex)=305nm,λ_(em)=347nm。当铈的浓度在5×10~(-7)～5×10~(-5)mol/L范围内与荧光强度呈线性关系。用本法测定了稀土样品和合成样品中铈的含量。     

PMDA-BPDA-HAB聚苯并噁唑的合成及耐热性

用廉价的均苯四甲酸二酐(PMDA)代替部分或全部3,3,′4,4′-联苯四羧酸二酐(BPDA),与3,3′-二羟基联苯胺(HAB)进行缩聚,然后脱水酰亚胺化,制备了5种聚酰亚胺(PI)。TGA分析显示,这些PI的DTG曲线为2个峰,可分为生成聚苯并唑(PBO)再发生PBO分解的2个阶段。PI膜在500℃通N2气1 h,所得聚合物膜的DTG曲线仅为1个峰,表明这些PI可充分转变成PBO。用FTIR表征了PI和PBO膜的结构。PBO的耐热性(用失重5%时的温度Td表示)比PI高100~170℃。PMDA-HAB PBO的耐热性高于BPDA-HABPBO。HAB-BPDA-PMDA PBO的耐热性优于二元PBO。当PMDA在二酐单体中所占的摩尔分数为75%时,PBO的Td高达643℃。     

Effect of Transition Metals on Selective Hydrogenation of Cinnamaldehyde over Pt／ZrO2 Catalysts

The effect of transition metals (Cr, Mn, Fe, Co and Ni) on the hydrogenation of cinnamaldehyde over Pt/ZrO2 catalysts was studied in ethanol at 343K under 2.0MPa H2 pressure. PtCo/ZrO2 and PtFe/ZrO2 catalysts exhibit high selectivity and activity of hydrogenation for C=O (93.8% at 87.3% conversion and 83.6% at 88.6% conversion, respectively), and PtNi/ZrO2 exhibits high selectivity of hydrogenation for C=C (64.3% at 70.6% conversion). In the presence of trace H2O and NaOH, over the PtNi/ZrO2 (0.4wt%Ni) catalyst the selectivity to hydrocinnamalde hydereaches 90.6% and the conversion of cinnamaldehyde is 90.5%.     

The development and application of guidance on equipment qualification of analytical instruments

 This paper describes the development of guidance for the equipment qualification (EQ) of analytical instruments. EQ is a formal process that provides documented evidence that an instrument is fit for its intended purpose and kept in a state of maintenance and calibration consistent with its use.     

Step-scan TMDSC and high rate DSC study of the multiple melting behavior of poly(1,3-propylene terephthalate)

The multiple melting behavior of poly(1,3-propylene terephthalate) (PPT) samples after isothermal crystallization from the melt was studied. The step-scan temperature-modulated differential scanning calorimetry (TMDSC) and high rate DSC were used to investigate this behavior in conjunction with standard DSC, wide-angle X-ray diffraction (WAXD) and polarizing light microscopy (PLM). The effect of PPT average molecular weight on the melting was also examined. In general multiple endotherms after isothermal crystallization of PPT were attributed to a continuous crystal perfection process during the subsequent heating scan via melting-recrystallization-remelting. Multiple melting behavior was more pronounced for the low molecular weight PPT. Step-scan TMDSC showed that extensive recrystallization occurs in PPT samples, especially after rapid isothermal crystallization. In fact two recrystallization exothermic peaks were observed. High rate DSC revealed the initial morphology generated during the isothermal step and showed that the low and middle peaks are associated with melting of primary crystals while the high temperature peak should be attributed to melting of recrystallized material.     

Synthesis and Multinuclear NMR Study of Benzoyl Methylene Triparatolylphosphorane Ylide and the Reaction of this Ylide with Mercury(II) Halides

The reaction of the title ylide {PhCOCHP(p-tolyl)₃} with Pd(II), Pt(II). Hg(II), and Ag(I) in equimolar ratios using CH₃CN, CH₃OH, and CH₂Cl₂ as solvents have yielded [{(p-tolyl)₃PCHCOC₆H₅} PdCl₂]₂ (I), [{(p-tolyl)₃ PCHCOC₆H₅} PtCl₂]₂(2), [Hg(NO₃)₂ {(p-tolyl)₃ PCHCOC₆H₅}](3), and [Ag{(p-tolyl)₃ PCHCOC₆H₅ < eqid1 > ₂]⁺ (4). The IR, ¹H ¹³C, and ³¹P NMR together with micro analysis data of the products were obtained.     

Biodegradations of block copolymers composed of L- or D,L-lactide and six-membered cyclic carbonates prepared with organolanthanide initiators

Diblock copolymerizations of L - or D,L -lactide (LA) with trimethylene carbonate (TMC) or 2,2-dimethyltrimethylene carbonate (2,2-DTMC) with SmMe(C₅Me₅)₂-(tetrahydrofuran) as an initiator and triblock copolymerizations of L - or D,L -LA/cyclic carbonates/L - or D,L -LA with [Sm(C₅Me₅)₂]₂(PhCCCCPh) as an initiator generated the desired block copolymers. This article describes the comparison of biodegradabilities by proteinase K and a compost and mechanical properties between the resulting di- or triblock copolymers and random copolymers composed of L - or D,L -LA and cyclic carbonates. The scanning electron microscopic profiles of resulting polymers were measured to understand the morphological change during biodegradation. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3572–3588, 2003     

improvement of the Specificity of Surface Plasmon Resonance with BSA-modified Chip

Recently, surface plasmon resonance (SPR) become more and more popular without the need of the label technology1-3. However, sometimes, a number of experimental artifacts complicate the final biosensor analysis4-7. The utilization of a reference surface c…     

Determination of carcinoembryonic antigen using a novel amperometric enzyme-electrode based on layer-by-layer assembly of gold nanoparticles and thionine

Electrochemical sensing of carcinoembryonic antigen(CEA)on a gold electrode modified by the se- quential incorporation of the mediator,thionine(Thi),and gold nanoparticles(nano-Au),through co- valent linkage and electrostatic interactions onto a self-assembled monolayer configuration is de- scribed in this paper.The enzyme,horseradish peroxidase(HRP),was employed to block the possible remaining active sites of the nano-Au monolayer,avoid the non-specific adsorption,instead of bovine serum albumin(BSA),and amplify the response of the antigen-antibody reaction.Electrochemical ex- periments indicated highly efficient electron transfer by the imbedded Thi mediator and adsorbed nano-Au.The HRP kept its activity after immobilization,and the studied electrode showed sensitive response to CEA and high stability during a long period of storage.The working range for the system was 2.5 to 80.0 ng/mL with a detection limit of 0.90 ng/mL.The model membrane system in this work is a potential biosensor for mimicking the other immunosensor and enzyme sensor.     

Novel Designing of Chemically Modified Electrode (CME) of the Bio-MOF-1 for the Detection of Dopamine Based on Inhibition of [Ru(bpy)3]2+/DBAE System

Metal organic frameworks (MOFs) have attracted extensive attention in electrochemical research fields due to their high surface area and controlled porosity. Current study is design to investigate the ECL performance of the chemically modified electrode (CME) based on the bio-MOF-1, a porous zinc-adenine framework, which loaded ruthenium complex and employed for the detection of dopamine (DA). The composite material [Ru(bpy)₃]²⁺@bio-MOF-1 (Ru-bMOF) modified carbon glassy electrode (Ru-bMOF/GCE) exhibited an excellent ECL performance having a linear co-efficient response (R²=0.9968) for 2-(dibutyl amino) ethanol (DBAE), a classical ECL co-reactant was obtained over a concentration range of 1.0×10⁻⁹ M to 1.0×10⁻⁴ M in 0.10 M pH=6.0 phosphate buffer solution (PBS). Furthermore, DA was detected based on its inhibition effect on [Ru(bpy)₃]²⁺/DBAE system. Compared to traditional analytical methods, this method has various advantages such as simple electrode preparation, quick response, high reproducibility (RSD<2.0 %), low limit of detection (LOD=1.0×10⁻¹⁰ mol/L). This chemical investigated modified electrode had exploited potential for detection of DA.