Multiwavelength spectrophotometric determination of protolytic constants of 4-(2-pyridylazo) resorcinol (PAR) in binary DMF-water mixtures

A multiwavelength spectrophotometric titration method was applied to study the protolytic constants of 4-(2-pyridylazo) resorcinol(PAR), in binary DMF + water mixtures. UV-vis absorption spectra of PAR solution were recorded in the course of pH-metric titration of acidic solutions of PAR with standard base solution. The protolytic equilibrium constants, spectral profiles, concentration diagrams and also the number of components have been calculated from the fitting of the pH-spectral titration data with appropriate mass balance equations by a home written program according to an established target factor analysis. To precise determination of number of absorptive components a recently developed statistical indicator function (IND function) was used. A glass electrode calibration procedure based on a four-parameter equation pH=α+SpcH+JH⁺[H⁺]+JOH⁻Kw/[H⁺] based on the Gran's plots was used to obtain pH readings in the concentration scale (p_cH). It has been observed that there is an inverse relationship between second and third protolytic constants and mole fraction of DMF. The effect of the solvent on the protolytic constants was discussed.     

Complexes of organolead and organotin ions with 1-(2-pyridylazo)-2-naphthol

The stability constants of the complexes of 1-(2-pyridylazo)-2-naphthol with several organotin and lead ions were determined spectrophotometrically in aqueous 20% (v/v) dioxane and were shown to have very high values. The extraction of the complex of (C₂H₅)₂Pb²⁺ from water into chloroform was studied, and the formation of an extractable (C₂H₅)₂Pb(PAN)(OH) complex is postulated.     

A Preliminary Investigation of the Solution Complexation of 4-Sulphonic calix[n]arenes with Testosterone

The complexation between water soluble calixarenes and testosterone has been studied. Stability constants of the host guest complexes of 4-sulphonic calix[n]arenes (n = 4, 6 and 8) with testosterone in water and buffers (pH 5.8, 7.3 and 10.0) were determined from phase solubility curves. These solubility curves indicated that the complexes were all of the A_L type. The constants were in the range 26–341 M^-1, dependent on the size of the calixarene and the pH of the solutions.     

UV-spectroscopic study of the influence of traces of water on the protolytic equilibria of substituted pyridine N-oxides in aprotic solvents

Using a UV-spectrophotometric method, an attempt has been made to estimate quantitatively the influence of traces of water in aprotic solvents on the acidic-basic equilibria involving heterocyclic N-oxides. The N-oxides under study were pyridine N-oxide (PyO), 4-methoxy-pyridine N-oxide (4-MeOPyO), and 2-, 3-, and 4-picoline N-oxide (2-, 3-, and 4-PicO). For particular N-oxide the UV-spectra of acetonitrile solutions containing the free base and/or its simple or semiperchlorate have been recorded. To carry out the calculations various equilibrium models which include the protolytic equilibrium with water and basic species present in the solvent have been tested using the program STOICHIO which is based on non-linear regression analysis. It turned out that apart from the acidic-basic dissociation of a protonated N-oxide and cationic homoconjugation (the equilibria which are usually considered in such systems) it is absolutely necessary to take into account the protolytic equilibrium between the cationic acid and water present as impurity. Implications concerning investigations of other equilibrium systems in aprotic solvents and, in particular, the quality of the acidity constants for the calibration agents used in potentiometry are discussed.     

Coulometric titrations in microscale study of ionic equilibria

Summary Coulometric titration, a well established technique in research and in routine analysis, can successfully be applied to the study of ionic equilibria in solution. Processes, where either lyate or lyonium ions serve as titrants, for determination of acids and bases, respectively, were investigated. Among the systems studied are: autoprotolytic equilibria of various amphiprotic solvents, acid-base equilibria in water, organic and mixed solvents and complexation reactions. In all these examples the titration was followed by a potentiometric pH-indicator electrode. In nonaqueous solvents coulometry overcame the limited solubility of electrolytes, the difficulty of standardization on solutions and the necessity of working in isolated systems to avoid contamination of the sample with water vapour or with carbon dioxide.Because volumes below 1 ml and concentrations in the order of 0.001 mol/l can be used, this technique can be successfully applied to the investigation of micromole amounts of compounds, when protolytic properties of substances available in minute quantities should be evaluated. Furthermore this technique was applied to the evaluation of protonation constants of biologically important buffers and the stability constants of their calcium complexes.     

Potentiometric study of end-point detection in the coulometric determination of carbon dioxide

The coulometric determination of carbon dioxide is based on the alkalimetric titration of the product of absorption of carbon dioxide in an organic solution of monoethanolamine. The processes occurring in various solvents have been investigated and optimized for analytical application. The protolytic reactions of 2-hydroxyethylcarbamic acid have been investigated in 2-propanol + 2, 5 and 10% water, dimethylformamide + 2% water, dimethylsulphoxide +5, 10 and 20% water. In coulometric generation of the base, 0.1M solutions of tetraethylammonium bromide in these solvents were used. The course of the titration was followed potentiometrically with glass and antimony indicator electrodes. From the titration curves the autoprotolysis constants of the mixed solvents and protonation constants of monoethanolamine in them were calculated. These constants and the concentration of monoethanolamine influence the size of the end-point break for the titrations. On this basis, optimal conditions for analysis have been selected and the total carbon content in samples of natural waters has been determined.     

Sensitive spectrophotometric determination of La(III) with 1-(2-pyridylazo)-2-naphthol

A simple and sensitive method for spectrophotometric determination of lanthanum has been developed. At pH 9.6, in presence of 50% ethanol, lanthanum reacts with 1-(-2-pyridylazo)-2-naphthol (PAN) to form a red complex which has two absorption maxima, at 545 and 510 nm. The molar absorptivity at 545 nm is 0.55 × 10⁴ liters · mol^?1 cm^?1. On the other hand, lanthanum reacts with PAN in pure ethanol to form a red complex at 530 nm, with high molar absorptivity (8 × 10⁴ liters · mol^?1 cm^?1).     

Solubility and Raman Spectroscopic Study of As(III) Speciation in Organic Compound-Water Solutions. A Hydration Approach for Aqueous Arsenic in Complex Solutions

Solubilities of arsenolite (As₂O₃, cub.) were measured from 22 to 90°C in water–acetone, water–acetic acid, and water—formic acid solutions of compositions ranging from the pure organic compound to pure water. Raman spectra were obtained at ambient temperature on As-containing water–acetic acid and water–acetone solutions. Results show that arsenic solvation by these organic compounds is negligible and hydroxide species dominate As speciation over a wide range of water activity (a_{H 2 O}> 0.01). The solubility data were analyzed using an approach based on stoichiometric hydration reactions. Results show that As₂O₃ solubility can be described as a function of water activity, independently of the nature of the organic compound, by involving two neutral As hydroxide complexes: As(OH)₃ and As(OH)₃·4H₂O. Stability constants derived for these species indicate that hydration weakens with increasing temperature. Calculations using these constants show that at low temperatures the tetrahydrate As(OH)₃·4H₂O is dominant in water-rich solutions; by contrast, in high-temperature crustal fluids, As(OH)₃ becomes the major As species. The proposed hydration model can be used to analyze solubility of arsenic-bearing minerals and arsenic transport in complex H₂O–CO₂—electrolyte solutions encountered in natural and industrial environments.     

H-point standard addition method for the selective simultaneous determination of nickel and copper using 1-(2-pyridylazo)-2-naphthol in Tween 80 micellar media.

The H-point standard addition method (HPSAM) has been applied for the simultaneous determination of nickel and copper in trace levels, using 1-(2-pyridylazo)-2-naphthol (PAN) as a chromogenic reagent in aqueous Tween 80 micellar media. Under the optimum condition, the simultaneous determinations of nickel and copper by HPSAM were performed. The absorbances at one pair of wavelengths, 548 and 579 nm, were monitored with the addition of standard solutions of copper. The method is able to accurately determine copper-to-nickel ratios of 15:1 to 1:10 (Wt/Wt). The effects of diverse ions on the determination of nickel and copper to investigate the selectivity of the method were also studied. The recommended procedure was successfully applied to some water and alloy samples.     

Cyanide thermodynamics 2. Stability constants of copper(I) cyanide complexes in aqueous acetonitrile mixtures

The stability (formation) constants of the binary Cu(I)-CN⁻ complexes have been measured in five aqueous mixtures containing from 10% to 70% v/v acetonitrile (MeCN) by glass electrode potentiometry at 25 °C and an ionic strength of l M (NaClO₄). The constants show monotonic increases with MeCN concentration, the changes being greatest for the higher order complexes, consistent with the unfavourable solvation of CN ⁻ in these mixtures. The sparing solubility of CuCN(s) prevented determination of the stability constant for CuCN ⁰ (soln.) at low MeCN concentrations.     

Co-crystallization with 1-(2-pyridylazo)-2-naphthol, and X-ray fluorescence, for trace metal analysis of water

Adding 20mg of 1-(2-pyridylazo)-2-naphthol (PAN) to a water sample at 70°, and filtering off the precipitate after cooling, gives efficient preconcentration prior to X-ray fluorescence analysis of water. Up to the capacity of about 100 μeq of PAN used, the trace metal recoveries are around 90% or higher for Cr³⁺, Mn²⁺, Ni²⁺, Cu²⁺, Zn²⁺, Hg²⁺ and Eu³⁺, and above 70% for many other ions. The recovery yields usually do not vary critically with pH in the neutral pH-range, and are practically independent of the sample salinity, sample volume and trace-metal concentration. Enrichment factors as high as 2 × 10⁵ can be achieved. Counting statistics would then allow detection limits of 0.03 ppM. The blank levels in commercial PAN, however, lead to typical detection limits of about 1 ppm. The coefficient of variation is typically in the 5–10% range at the 10-ppM level. The accuracy and applicability of the procedure are illustrated by comparative analyses on samples of synthetic solutions, river and drinking water.     

Sensing Element of a Benzopurpurin 4B-Based Optical Sensor for Determining the Acidity of Etch Solutions

Deposition conditions are studied, and a Langmuir–Blodgett film (LBF) based on the benzopurpurin 4B indicator immobilized in the polyamide acid salt matrix is obtained. The protolytic properties of the indicator are studied in water, micelles of cationic and nonionic surfactants, and LBFs. It is shown that, in going from water to the cited micelles and LBFs, pK _ind is shifted to the acidic region by 3.25, 1.18, and 2.30 pH units, respectively. The possibility of using the produced LBF as the sensing element of an optical sensor for the determination of the acidity of solutions in the pH range 1–0 is demonstrated. The LBF is applied to the determination of the acidity of solutions in etch baths. The response time in the operating range is 10–20 s; the standard deviation is no more than 4%.     

Enantioseparation and impurity determination of the enantiomers of novel phenylethanolamine derivatives by high performance liquid chromatography on amylose stationary phase

Simple and efficient analytical HPLC methods using Chiralpak AS-H as chiral stationary phase were developed for direct enantioseparation of 11 novel phenylethanolamine derivatives. The chromatographic experiments were performed in normal phase mode with n-hexane–ethanol–triethylamine (TEA) as mobile phase. Excellent baseline enantioseparation was obtained for most of compounds. The effects of the concentration of organic modifiers and column temperature were studied for the enantiomeric separation. The mechanism of chiral recognition was discussed based on the relationship between the thermodynamic parameters and structures of compounds. It was found that the enantioseparations were all enthalpy driven, and the tert-butyl groups of compounds had significant influence on the chiral recognition. Trantinterol enantiomers were resolved (R_s = 2.73) within 14 min using n-hexane–ethanol–TEA (98:2:0.1, v/v/v) as mobile phase with a flow rate of 0.8 mL min⁻¹ at 30 °C. The optimized method was validated for linearity, precision, accuracy and stability in solution and proved to be robust. The limits of detection (LOD) and quantification (LOQ) for (+)-trantinterol were 0.15 and 0.46 μg mL⁻¹. The method was applied for enantiomeric impurity determination of (−)-trantinterol bulk samples.     

Unraveling structure-reactivity relationships in SNV reactions: kinetics of the reactions of methoxybenzylidenemalononitrile, 2-(methylthiobenzylidene)-1,3-indandione, 2-(benzylthiobenzylidene)-1,3-indandione, and methyl beta-methylthio-alpha-nitrocinnamate with OH- and thiolate ions in aqueous DMSO.

The kinetics of the title reactions were determined in 50% DMSO-50% water (v/v) at 20 degrees C; n-BuS-, HOCH2CH2S-, and MeO2CCH2S- were used as thiolate ions. The reactions with the thiolate ions gave rise to two separate kinetic processes. The first refers to rapid, reversible attachment of RS- to the substrate leading to a tetrahedral intermediate (k1RS), k(-1)RS, the second to the conversion of the intermediate to products (k2RS). In most cases all of the rate constants (k1RS, k(-1)RS and k2RS could be determined. In combination with results from previous studies, a detailed discussion regarding the effects of activating substituents and leaving groups on rate and equilibrium constants as well as on intrinsic rate constants is presented. The reaction with OH- only allowed a determination of k1OH for nucleophilic attack on the substrate; in this case the tetrahedral intermediate remains at steady-state levels under all conditions.     

Application of Thermal-Lens Spectrometry to a Study of the Interaction of Trace Nickel(II) with Dimethylglyoxime

Thermal-lens spectrometry was applied to a study of the properties of a nickel(II) complex with dimethylglyoxime at a concentration level of n × 10^–8–n × 10^–6 mol/L. The possibility of determining the solubility of the complex and the characteristics of its adsorption on the glass surface of laboratory ware was demonstrated. The stability constants of the complex in water–ethanol mixtures (9 : 1) were determined. The found data made it possible to optimize the conditions for the photometric determination of nanomolar concentrations of nickel. The optimized procedure was used for a thermal-lens determination of nickel(II) traces in heteropoly compounds and high-purity water.     

2-[2-(6-Methylbenzothiazolyl)azo]-5-Diethylaminobenzoic acid as a new analytical reagent for the spectrophotometric determination of nickel

A new thiazolylazo chromogenic reagent, 2-[2-(6-methylbenzo-thiazoly)azo]-5-diethylaminobenzoic acid (6-Me-BTAEB), has been synthesized. Its chromogenic reaction with microamounts of nickel in the presence of sodium dodecylsulfate (SDS) has been thoroughly studied. 6-Me-BTAEB reacts with nickel(II) in weak acid medium containing appropriate amounts of SDS to form a blue-violet complex with high sensitivity, good selectivity and high stability. The composition is found to be 1:2 (nickel to 6-Me-BTAEB) and its absorption maximum is at 650 nm with an apparent molar absorptivity of 1.67 × 10⁵l mole^–1 cm^–1. Beer's law is obeyed over the range 0-0.4 g of nickel per ml. The proposed method has been applied to the direct determination of nickel in aluminium alloys, pure magnesium and low alloy steels at the 0.2–0.3% (w:w) level with satisfactory results.     

The uses of 1-(2-pyridylazo) 2-naphtol (PAN) impregnated Ambersorb 563 resin on the solid phase extraction of traces heavy metal ions and their determinations by atomic absorption spectrometry

1-(2-pyridylazo) 2-naphtol (PAN) impregnated Ambersorb 563 resin was used as solid phase extractor of copper, nickel, cadmium, lead, chromium and cobalt ions in aqueous solutions prior to their atomic absorption spectrometric determinations. The parameters including pH, sample volume, matrix effects were also investigated. The relative standard deviation (R.S.D.) of the combined method of sample treatment, preconcentration and determination with atomic absorption spectrometry is generally lower than 10%. The limit of detection was between 0.21 and 1.4 μg l⁻¹. The results were used for preconcentration of analyte ions from natural water samples. The method was also applied to a stream sediment standard reference material (GBW7309) for the determination of Cu, Ni, Cd, Pb, Cr and Co.     

Spectrophotometric determination of manganese with 1-(2-pyridylazo)-2-naphthol and a non-ionic surfactant

A spectrophotometric method for the determination of trace amounts of manganese with 1-(2-pyridylazo)-2-naphthol (PAN) is described. The method is based on the measurement of absorbance of the manganese—PAN chelate solubilized with a non-ionic surfactant, Triton X-100. No extraction procedure is required in the method proposed. High concentrations of calcium, aluminium and magnesium do not interfere. The presence of up to 10 ppm of lead can be tolerated. Iron, cadmium, zinc, cobalt and nickel can be effectively masked with potassium cyanide. Beer's law is obeyed up to 2 ppm of manganese. The molar absorptivity of the manganese—PAN chelate found was 4.4 × 10⁴ l. mole ⁻¹. cm⁻¹ at 562 nm. The overall stability constant of Mn(PAN)₂ in 0.4% Triton X-100 medium is 10^16.8.     

Preconcentration and Determination of Trace Nickel Using 1-(2-Pyridylazo)-2-Naphtol (PAN) Immobilized on Surfactant-Coated Alumina

A microcolumn of alumina modified with sodium dodecyl sulfate (SDS) and 1-(2-pyridylazo)-2-naphthol (PAN) was prepared for the preconcentration of trace nickel from water samples for a flame atomic absorption spectrometry (FAAS) determination. Under optimized conditions (pH = 4.0; flow rate, 5 mL min^–1) nickel (II) was retained on the column. The nickel collected on the column was eluted with 5 mL of 0.5 M nitric acid. Recovery was greater than 96.7%. A concentration factor of 300 can be achieved by passing 1500 mL of sample through the microcolumn. The relative standard deviation (ten replicate analyses) at the 40 ng mL^–1 level for nickel was 2.4%, and the corresponding limit of detection (based on 3) was 0.06 ng mL^–1. The method was applied to the determination of Ni in waste and mineral waters.     

Evaluation of 1-(2-thiazolylazo)-2-hydroxy-3-naphthoic acid as a metallochromic indicator

The acid dissociation constants of 1-(2-thiazolylazo)-2-hydroxy-3-naphthoic acid (TAHN) and the formation constants of Cu(II), Ni(II) and Zn(II) chelates of this dye have been determined spectrophotometrically at 25 degrees in a 5% v/v mixture of dioxan and water. The formation constants of the 1:2 chelates are smaller than those of other o-hydroxythiazolylazo compound chelates. TAHN is a satisfactory indicator for the titrations of Cu(II) and Ni(II) with EDTA.