聚合物对多壁碳纳米管的包覆改性研究

探讨了聚合物对碳纳米管的包覆改性.将多壁碳纳米管(MWNTs)通过浓硫酸和浓硝酸的混酸(体积比=3∶1)处理,使其带上羧基.将羧化MWNTs与甲基丙烯酸缩水甘油酯(GMA),苯乙烯双组分接枝聚苯乙烯(PS-g-(GMA-co-St))通过溶液共混方法,使其接在MWNTs上的羧基和GMA所带的环氧基团之间发生酯化反应,实现MWNTs表面接枝上PS-g-(GMA-co-St).扫描电镜观察表明,羧化MWNTs平均管径约为40nm,而接枝上PS-g-(GMA-co-St)的改性MWNTs管径可达约100nm.用四氢呋喃(THF)对表层包覆的PS-g-(GMA-co-St)刻蚀后,其直径降回到约40nm,这和先前观察到的羧化MWNTs的直径基本一致.对刻蚀后的MWNTs样品的FT-IR分析也表明MWNTs表面上存在接枝PS.表面经过PS-g-(GMA-co-St)修饰后,可以形成包覆层,为MWNTs在聚合物基体中分散、制备纳米功能材料提供了途径.     

Synthesis and study of a cyclophane displaying dual fluorescence emission: a novel ratiometric sensor for carboxylic acids in organic medium

The synthesis and fluorescent properties of a novel cyclophane containing two l-valine units and one naphthalene chromophore are described. Synthesis of the macrocycle 1 was accomplished without using high-dilution methods in moderate to high yields. The fluorescence spectrum of 1 in neutral dichloromethane shows a band at 390 nm attributable to emission from an exciplex formed between the naphthalene unit and the neighboring amine groups. Addition of trifluoroacetic acid restores the typical naphthalene emission at 330 nm. Due to the fact that both emissions have similar intensities under the working conditions, the ratio between them can be used to obtain a ratiometric response to carboxylic acids in organic medium.     

Composition dependent frequency upconversion of Er/Yb-codoped lead chloride tellurite glasses

The green and red upconversion luminescence of Er³⁺ in lead chloride tellurite glasses excited at 980 nm is investigated. Three intense emission bands centered at 530, 545, and 658 nm corresponding to the transitions ⁴S_3/2→⁴I_15/2, ²H_11/2→⁴I_15/2 and ⁴F_9/2→⁴I_15/2, respectively, were simultaneously observed at room temperature. With increasing PbCl₂ content, the intensity of green (530 nm) emissions increase slightly, while the green (545 nm) and red (658 nm) emissions increase significantly. The results indicate that PbCl₂ has more influence on the green (545 nm) and red (658 nm) emissions than the green (530 nm) emission. The dependence of upconversion intensities on excitation power and possible upconversion mechanisms are discussed and evaluated.     

Classification of edible and lampante virgin olive oil based on synchronous fluorescence and total luminescence spectroscopy

Total luminescence and synchronous fluorescence spectroscopies were tested as regards their ability to differentiate edible from lampante virgin olive oils. Total luminescence spectra were recorded by measuring the emission spectra in the range 350-720 nm at excitation wavelengths from 320 to 535 nm. The synchronous fluorescence spectra of 41 edible and 32 lampante virgin olive oils were acquired by synchronous scanning the excitation and emission monochromator maintained at an offset value of 80 nm. Classification of virgin olive oils based on their synchronous fluorescence spectra was performed by hierarchical cluster analysis and principal component analysis using the spectral range of 429-545 nm. Principal component analysis provided better discrimination between the two classes, without any classification error, while hierarchical cluster analysis allowed 97.3% correct classification. These results indicate the capability of fluorescence techniques to differentiate virgin olive oils according to their quality.     

Facile synthesis of multifunctional multiwalled carbon nanotubes/Fe3O4 nanoparticles/polyaniline composite nanotubes

With an average diameter of 100-150 nm, composite nanotubes of polyaniline (PANI)/multiwalled carbon nanotubes (MWNTs) containing Fe₃O₄ nanoparticles (NPs) were synthesized by a two-step method. First, we synthesized monodispersed Fe₃O₄ NPs (d=17.6 nm, σ=1.92 nm) on the surface of MWNTs and then decorated the nanocomposites with a PANI layer via a self-assembly method. SEM and TEM images indicated that the obtained samples had the morphologies of nanotubes. The molecular structure and composition of MWNTs/Fe₃O₄ NPs/PANI nanotubes were characterized by Fourier transform infrared spectra (FTIR), energy dispersive X-ray spectrometry (EDX), X-ray photoelectron spectra (XPS), X-ray diffraction (XRD) and Raman spectra. UV-vis spectra confirmed the existence of PANI and its response to acid and alkali. As a multifunctional material, the conductivity and magnetic properties of MWNTs/Fe₃O₄ NPs/PANI composites nanotubes were also investigated.     

Synthesis and spectral properties of Eu-doped YF3 nanobundles

YF₃:Eu³⁺ nanobundles were synthesized by a facile microemulsion method. Analysis of X-ray diffraction, scanning electron microscope, and transmission electron microscopy reveals that each nanobundle consists of numerous nanowhiskers with a mean length of ∼500 nm and a mean diameter of ∼2 nm. Under 393-nm excitation, the luminescence was dominated by ⁵D₀ → ⁷F₁ transition, indicating the inversion symmetry of Eu³⁺ site. The luminescence intensity increased with increasing Eu³⁺ concentration, up to about 30 mol%, and then decreased abruptly. The peak positions and spectral shapes of emissions were independent of Eu³⁺ concentration. Finally, the critical distance of energy transfer was calculated.     

Studies on interactions of excited cadmium and mercury atoms with secondary and tertiary alkyl- and silylamines in gas phase

The Cd(³P₁)- and Hg(³P₁)-photosensitized emissions of some secondary and tertiary alkyl- and silylamines have been investigated under conditions of steady illumination at 493 and 298 K, respectively. The emission bands were observed at around 440 nm in the cadmium-photosensitized reactions of these amines. In contrast, no appreciable emission bands were observed in the mercury-photosensitized reactions of these amines. However, upon addition of tert-butyl alcohol to the amine-mercury system, an emission band evolved at around 350 nm in the mercury-photosensitization. The peak-wavelengths for secondary and tertiary alkyl- and silylamines are slightly shorter than the values predicted from the correlations between the peak wavelength and the first ionization energy obtained in the cadmium- and mercury-photosensitized luminescence of ammonia and primary amines. The quenching efficiencies of the cadmium and mercury resonance lines by secondary alkyl- and silylamines are higher than those by tertiary alkyl- and silylamines. These observations suggest that the steric hindrance by the alkyl and silyl groups to the approach of the nitrogen atom in the amines to excited cadmium and mercury atoms seems to be an important factor for the stabilization of the exciplexes and the quenching of the resonance lines. The behavior of silylamines is similar to that of alkylamines in cadmium- and mercury-photosensitized reactions.     

Thermal oxidative degradation of additive-free polypropylene pellets investigated by multichannel Fourier-transform chemiluminescence spectroscopy

Thermal oxidative degradation of additive-free polypropylene pellets heated isothermally in dry air at 150 and 180 °C (below and above the melting point of 163 °C) was investigated by multichannel Fourier-transform chemiluminescence spectroscopy. The initial peak wavelength of chemiluminescence emission at 490 nm remained constant during the early stages of thermal degradation, but new emissions developed with time in the red spectral region over an extended oxidation period. The time-dependent luminescence spectra were deconvoluted into three emission bands by least-squares fitting using Gaussian curves. We concluded that at least three groups of luminescent species (luminophores), having different conjugation lengths, were generated by thermal oxidation over extended periods and show luminescence around 490, 660, and 740 nm.     

Effect of nanoscaled SnO2 coating on ZnS:Mn phosphors under electron irradiation

The luminescence properties of SnO₂-coated ZnS:Mn phosphors are investigated. In the case of photoluminescence, emission intensities show little change when SnO₂ is coated on the surface of ZnS:Mn, while in the case of cathodoluminescence (CL), emission intensities vary depending on excitation energies. In order to determine the luminescence behaviors, surface analyses of the phosphors were performed. Auger electron spectroscopy showed that the width of the SnO₂ layer on the ZnS:Mn phosphor was saturated at approximately 120 nm. Also, X-ray photoelectron spectroscopy indicated that the SnO₂ layers are well formed and saturated when the molar ratios of Sn/Zn are larger than 0.005. These results suggest that the changes in the CL emissions can be attributed to a lowering of the junction barrier.     

Decoration of carbon nanotubes with iron oxide

A magnetic composite of multiwalls carbon nanotubes (MWNTs) decorated with iron oxide nanoparticles was synthesized successfully by a simple and effective chemistry precipitation method. The composite was characterized by X-ray diffraction analysis (XRD), Mössbauer spectrum (MS), transmission electron microscopy (TEM), and Fourier transform spectroscopy (FTIR) techniques. The patterns of XRD and MS indicated that MWNTs, γ-Fe₂O₃, and Fe₃O₄ coexisted in the composite. The TEM observation indicated that the nanoparticles of iron oxide were attached on the surface of the MWNTs, and the sizes of the particles ranged from 25 to 80 nm. FTIR spectra showed that SO₄⁻ functional groups existed on the surface of MWNTs after modification by sodium dodecylbenzene sulfonic acid (SDBS), which could immobilize Fe³⁺ ions onto the MWNTs. The hysteresis loops of the MWNTs and decorated MWNTs were measured by vibrating sample magnetometer (VSM), and the results showed that the composite was ferromagnetism with the saturated magnetization of 20.07 emu/g, and the coercive of 163.44 Oe.     

Oxobenzo[f]benzopyrans as new fluorescent photolabile protecting groups for the carboxylic function

The properties of three oxobenzo[f]benzopyrans as new fluorogenic photolabile protecting groups for the carboxylic function of amino acids were studied. Fluorescent amino acid conjugates were efficiently prepared and characterised. Photodeprotection of these compounds was carried out by irradiation at 300, 350 and 419 nm, the most suitable wavelength being 350 nm, on account of short irradiation times and good deprotection yields.     

Development of a new fluorescent probe for transition metal cations based upon fluorescence resonance energy transfer

A novel fluorescent probe for metal cations, which has a large Stokes shift, was synthesized from the reaction of N-(3-carboxy-2-naphthyl)-ethylenediamine-N,N′,N′-triacetic acid (CNEDTA) with 4-(N,N-dimethylaminosulfonyl)-7-(2-aminoethylamino)-2,1,3-benzoxadiazole (DBD-ED). The large Stokes shift is due to the FRET phenomenon between a donor (CNEDTA) and an acceptor (DBD-ED) fluorophore. When the fluorescent probe, DBD-ED-CNEDTA, was excited at 240, 340 and 440 nm, an emission maximum was observed only at 560 nm. However, the fluorescence (FL) at 480 nm, based upon the CNEDTA moiety, was not detected with excitation at 340 nm. The FL intensity of DBD-ED-CNEDTA was dependent upon the acidity of the medium and highest at pH 4.1. DBD-ED-CNEDTA reacted with metal cations, i.e., Zn, Cd, Al, Y, and La, in aqueous medium to form chelates. The spectral change of FL excitation and emission was small before and after the addition of the metal ions. However, the FL intensity was dependent upon the concentrations of the metal ions. In the case of Zn²⁺, the molar ratio bound with DBD-ED-CNEDTA was calculated as 1:1. The FL intensities after chelate formation of Zn/DBD-ED-CNEDTA (1:1) were enhanced by 3.8-fold (excitation at 340 nm, emission at 560 nm), 4.2-fold (excitation at 440 nm, emission at 560 nm), and 5.9-fold (excitation at 240 nm, emission at 560 nm), respectively. The FL probe was applied to the determination of Zn in a food supplement.     

Fabrication of polyaniline/carbon nanotube composite modified electrode and its electrocatalytic property to the reduction of nitrite

A polyaniline (PANI)/carbon nanotubes (CNTs) composite modified electrode was fabricated by galvanostatic electropolymerization of aniline on multi-walled carbon nanotubes (MWNTs)-modified gold electrode. The electrode thus prepared exhibits enhanced electrocatalytic behavior to the reduction of nitrite and facilitates the detection of nitrite at an applied potential of 0.0 V. Although the amperometric responses toward nitrite at MWNTs/gold and PANI/gold electrodes have also been observed in the experiments, these responses are far less than that obtained at PANI/MWNTs/gold electrode. The effects of electropolymerization time, MWNTs concentration and pH value of the detection solution on the current response of the composite modified electrode toward sodium nitrite, were investigated and discussed. A linear range from 5.0 × 10⁻⁶ to 1.5 × 10⁻² M for the detection of sodium nitrite has been observed at the PANI/MWNTs modified electrode with a sensitivity of 719.2 mA M⁻¹ cm⁻² and a detection limit of 1.0 μM based on a signal-to-noise ratio of 3.     

Influence of carbon shell structure on electrochemical performance of multi-walled carbon nanotube electrodes

Core/shell nanostructures have received considerable attention due to the synergistic effect of their combination of materials. In this work, core/shell carbon/multi walled carbon nanotubes (MWNTs) (C-MWNTs) composed of core MWNTs and carbon shells were prepared to obtain a new type of carbon electrode materials. Carbon shells containing nitrogen groups were prepared by coating polyaniline (PANI) onto the MWNTs by in situ polymerization and subsequent carbonization at 850 °C. After carbonization, the C-MWNTs contained 5.84% nitrogen and showed a hollow structure and crystallinity like that of pristine MWNTs. In addition, the C-MWNTs exhibited electrochemical performance superior to that of pristine MWNTs, and the highest specific capacitance (231 F g⁻¹) of the C-MWNTs was obtained at a scan rate of 0.1 A g⁻¹, as compared to 152 F g⁻¹ for pristine MWNTs. This superior performance is attributed to the maintenance of high electrical conductivity by the π–π interaction between the carbon layer and the MWNTs, increased specific surface area of C-MWNTs, and the presence of nitrogen groups formed on the carbon electrode after the carbonization of the shell PANI.     

Photophysical properties of praseodymium complexes with aromatic carboxylic acids: double light conversion both in ultraviolet and visible region

A series of luminescent praseodymium complexes with different aromatic carboxylic acids have been synthesized and characterized. The photophysical properties of these complexes have been studied with ultraviolet spectra, phosphorescence spectra and fluorescence spectra. Ultraviolet absorption spectra show that the praseodymium complexes systems with aromatic carboxylate form the more extensive conjugated systems to be suitable for the distribution of electron in the whole coordination environment, resulting in the energy decrease and red-shifts of ultraviolet spectral bands. Phosphorescence spectra suggest that excited triplet state of aromatic carboxylic acids, which can indicate the energy match and intermolecular energy transfer process between the excited triplet state of ligands and the resonant emissive energy level of Pr ions. The emission spectra of all praseodymium complexes show two emission peaks under the excitation band of 245 nm at about 395 and 595 nm, respectively, while one peak at about 595 nm under 415 nm excitation, which attributed to be 1S0-->1I6 (395 nm) transition and the characteristic emission 1D2-->3H4 (595 nm) transition of Pr3+ ion. The 1S0-->1I6 transition can be speculated to belong to the transition of charge transfer state, and the 1D2-->3H4 can be further proved that there exists an antenna effect in the luminescence of praseodymium with aromatic carboxylic acids. In conclusion, the praseodymium complexes systems can realize the double proton light conversion both in the ultraviolet and visible region, which can be further studied to have potential application.     

Luminescence emission of natural NaCl

The luminescence properties of synthetic alkali halides in general and different doped synthetic sodium chloride (NaCl) in particular have been widely studied. However, the spectral emission of natural NaCl has been scarcely reported. Accordingly, this work reports on the thermoluminescence (TL), infrared stimulated luminescence (IRSL) and radioluminescence (RL) response of the well-characterized natural NaCl (by means of X-ray fluorescence and differential thermal and thermogravimetric techniques) in the range of 200-800 nm. As observed in the 3D-TL plots, the main emission of the irradiated samples appears in the UV-blue region and can be deconvoluted into four groups of components (at 70, 180, 220 and 315 °C) assuming first order kinetics. The non-irradiated samples exhibited a negligible luminescence signal. The RL response reveals the appearance of five bands peaked at 290, 370, 430, 500 and 620 nm. The IRSL spectral emission shows a low intensity broad band with non-well defined peaks.     

Effect of nitrogen-containing groups on enhanced capacitive behaviors of multi-walled carbon nanotubes

In this work, electrochemical properties of surface treated multi-walled carbon nanotubes (MWNTs) are studied in supercapacitors. Nitrogen and oxygen functional groups containing MWNTs are prepared by urea and acidic treatments, respectively. The surface properties of the MWNTs are confirmed by X-ray photoelectron spectroscopy (XPS) and zeta-potential measurements. The textural properties are characterized by N₂ adsorption/desorption isotherm at 77 K using the BET eqaution, BJH method, and HK method. The electrochemical properties of the MWNTs are accumulated by cyclic voltammetry, impedance spectra, and charge-discharge cycling performance in 1 M H₂SO₄ at room temperature. As a result, the functionalized MWNTs lead to an increase in capacitance as compared with pristine MWNTs. It suggests that the pyridinic and pyridinic-N-oxides nitrogen species have effects on the specific capacitance due to the positive charge, and thus an improved electron transfer at high current loads results, the most important functional groups affecting capacitive behaviors.     

Novel Eu-doped lead telluroborate glasses for red laser source applications

We report the absorption, luminescence and decay analysis of Eu³⁺-doped lead telluroborate (PTBEu) glasses for different Eu³⁺ concentrations ranging from 0.1 to 2.0 mol%. Judd-Ofelt intensity parameters obtained from ⁵D₀→⁷F_J=0-6 emission transitions of Eu³⁺ were used to calculate the radiative transition probabilities, luminescence branching ratios and radiative decay times. The luminescence spectra and decay times were measured at 464 nm excitation. The optical band gap energies are also determined. The luminescence intensity ratio, color purity and emission cross-section values support that the PTBEu20 glass is a suitable candidate for red laser source applications.     

Novel photoluminescent lanthanidomesogens forming bilayer smectic phase derived from blue light emitting liquid crystalline, one ring O-donor Schiff-base ligands

A series of new mononuclear lanthanide(III)-salicylaldimine complexes of the type [Ln(LH)₃(NO₃)₃] (Ln = La, Pr, Sm and Gd; LH = N-(2-hydroxyethyl)-4n-alkoxysalicylaldimine, n = 14, 18) have been synthesized and characterized by FT-IR, ¹H NMR, ¹³C NMR, UV-Vis, FAB-mass and magnetic susceptibility measurements. The ligand (LH) coordinate to lanthanide ions in zwitterionic form via the phenolic-oxygen with the proton shifted to the imine-nitrogen. The nitrato groups occurring in chelated bidentate fashion complete a nine-coordinate geometry. Polarized optical microscopy (POM) and differential scanning calorimetry (DSC) show that the ligands are monotropic and their complexes exhibit enantiotropic highly viscous smectic A (SmA) mesophase in the temperature range 60-185 °C. A bilayer self organized assembly of the molecules in the mesophase are proposed on the basis of the small angle XRD study. The ligands are blue light emitters with a broad emission maxima at ∼447 nm while the lanthanide complexes show intense emission in the visible range (∼465-679 nm) at 350 nm excitation. The samarium(III) complex, [Sm(LH)₃(NO₃)₃] is distinct from the rest in emitting bright orange light (∼660 nm, Φ = 48%). The S_o-S₁ excitation band being stronger than the direct f-f excitation in the samarium complex clearly suggests that the Schiff-base ligands efficiently sensitize the luminescence of Sm³⁺. DFT calculations have been performed using DMol3 program at BLYP/DNP level to obtain the stable electronic structure of the ligand and complex.     

Electrochemical characteristics of the immobilization of calf thymus DNA molecules on multi-walled carbon nanotubes

Immobilization of DNA on carbon nanotubes plays an important role in the development of new types of miniature DNA biosensors. Electrochemical characteristics of the immobilization of calf thymus DNA molecules on the surfaces of multi-walled carbon nanotubes (MWNTs) have been investigated by cyclic voltammetry and electrochemical impedance analysis. The peak currents for Fe(CN)(6)(3-)/Fe(CN)(6)(4-) redox couple observed in the cyclic voltammograms decrease and the electron-transfer resistance (R(et)) obtained from the Nyquist plots increase due to the immobilization of DNA molecules (dsDNA or ssDNA) on the surfaces of MWNTs. Most of calf thymus DNA are covalently immobilized on MWNTs via diimide-activated amidation between the carboxylic acid groups on the carbon nanotubes and the amino groups on DNA bases, though the direct adsorption of the DNA molecules on MWNTs can be observed. Additionally, the interaction between DNA molecules immobilized on MWNTs and small biomolecules (ethidium bromide) can be observed obviously by cyclic voltammetry and electrochemical impedance analysis. This implies that the DNA molecules immobilized at the surface of MWNTs, with little structure change, still has the ability to interact with small biomolecules.