Removal of Cd Ions by Sol-Gel Silica Doped with 1-(2-Pyridylazo)-2-Naphthol

1-(2-Pyridylazo)-2-Naphthol (PAN) doped sol-gel silica has been investigated for removal of metal ions from aqueous media. In the doped sol-gel silica, the large reagent molecules are entrapped inside the pores while small metal ions can diffuse into the pores where they are complexed by the reagent and retained inside the pores. This new solid sorbent was applied for removal of Cd(II) from aqueous solutions. The kinetics, adsorption isotherm, equilibration time and pH effect on the removal were studied to optimize the conditions to be utilized on a large scale. It was observed that a sol gel loaded with 0.09 mmol PAN/g, had a capacity of 0.044 mmol Cd/g. The desorption of metal ions was carried by 1 M HCl and the sol-gel silica sorbent could be regenerated and reused repeatedly.     

Adsorption of Cd(II) by Sol-Gel Silica Doped with N-(dipropylcarbamothioyl)thiophene-2-carboxamide

Sol-gel silica was doped with N,N-(dipropylcarbamothioyl) thiophene-2-carboxamide to investigate the sorption of cadmium (Cd) ions from aqueous media. In doped sol-gel silica, the large reagent molecules entrap into pores, whereas, small metal ions diffuse into pores where they make complex with doped reagent. This complexation can be accomplished by either ion exchange or chelation. Doped sol-gel sorbent was applied for removal of Cd(II) from aqueous solution in our study. Adsorption kinetics, adsorption isotherm, equilibration time, effect of initial concentration of adsorbate, and pH effect on the metal removal were studied to optimize the conditions. The prepared adsorbent shows rapid equilibrium and high stability toward high temperature and applied medium. In addition, desorption of metal ions was carried out by 1 M HCl and, thereafter, sol-gel silica adsorbent was regenerated and reused periodically.     

Silica gel modified with Eriochrome Blue SE as a sorbent in trace analysis for metal ions

The sorption of 14 metal ions on silica gel impregnated with a mixture of Aliquat 336 and Eriochrome Blue SE was investigated. It was found that the sorption behaviour depends upon the species and the pH of the loading solution. Alkali metal ions were not retained under any of the investigated conditions. The retained metal ions can be eluted with dilute solutions of hydrochloric or perchloric acid without significant elution of the chelating reagent from the sorbent. The sorbent was used for the separation of metal ion mixtures by column — extraction chromatography and for additional purification of some salt solutions from trace amounts of Zn, Cd, Pb and Cu. The effectiveness of purification was confirmed by anodic stripping voltammetry.     

A Generic Technique for Coating Doped Sol-Gel Films onto the Inside of Tubes for Use as Colorimetric Sensors

Sol-gel thin films have been doped with bromophenol blue and eriochrome cyanine RC for measuring pH and Cu⁺⁺ in solution respectively. The films were coated inside glass tubes by a novel method. Films doped with bromophenol blue responded to pH changes from pH 3 to 8. They were stable to variations in temperature from 20°C to 40°C. The sensing films have been subjected to leaching studies in different pH buffer solutions. Copper ions in solution have been measured to a minimum concentration of 0.6 ppm by eriochrome immobilised in sol-gel films. The interferences of other metal ions were also studied. Doped sol-gel films coated onto the inside of test tubes offer a simple, none-invasive, reusable and fast optical chemical sensing technique for the measurement of colour by spectroscopy or colorimetry.     

氧化铜/二氧化硅多孔复合材料的制备及其对亚甲基蓝的吸附性能

采用聚乙二醇（PEG）为模板,通过溶胶凝胶法-水热法制备出CuO/SiO2多孔复合材料,使用FTIR、HRTEM、XRD和BET等技术手段对目标产物进行了表征;研究添加CuO质量及反应温度等反应条件对复合材料的孔结构特征的影响。 用目标产物作为吸附材料,研究了其对有机染料亚甲基蓝的吸附性能,结果表明,CuO/SiO2多孔复合材料对亚甲基蓝具有良好的吸附效果,尤其是含CuO质量分数为15%的样品在用量0.015 g、体系pH=9、搅拌时间为2 h的条件下,对10 mL亚甲基蓝（4 mg/L）的去除率最高可达97.17％。 对吸附的过程和机理进行了初步探讨。     

Properties and Application of a Chelating Sorbent Prepared by Modification of LiChroprep-NH<Subscript>2</Subscript> with Calcon

A new chelating sorbent for metal ions was prepared by modification of chemically modified silica – LiChroprep-NH₂ with Calcon. The molecular mechanism of binding this reagent to the surface of the applied carrier is presented. The properties of this sorbent were compared to analogous sorbents with a plain silica carrier and chemically modified silicas – LiChroprep-RP containing Calcon. The advantages of the new sorbent compared to the silica and LiChroprep-RP chelating sorbents are demonstrated. The sorbent obtained was applied as stationary phase in solid-phase extraction (SPE) for separations of some chosen mixtures of metal ions and for additional purification of aqueous solutions of salts of alkali metals from trace amounts of heavy metals. The multiple use of the sorbent based on LiChroprep-NH₂ in sorption-desorption processes of metal ions without deterioration of its sorption capacity is demonstrated.     

Sorption of Cobalt on Modified Silica Gel Materials

Various silica gel materials were chemically modified with imidazole, diaza-18-crown-6 (DA18C6) and dibenzod-18-crown-6 (DB18C6). The degree of functionalization of the covalently attached molecule was calculated from C, H, N analysis and ranged between 0.270 and 0.552 mmol/g (for sorbents with imidazole) and between 0.043 and 0.062 mmol/g (for sorbents with DA18C6 and DB18C6). The degree of functionalization depends on the reflux time and silica gel matrix used. Experimental sorption capacity ranged between 0.038 and 0.228 mmol/g (for sorbents with imidazole) and between 0.019 and 0.050 mmol/g (for sorbents with DA18C6 and DB18C6). Synthesized hexagonal mesoporous silica matrix MCM-41 with uniform pore diameter <40 Å was used too. Change of pore diameters of silica gel support to larger pores should have a positive influence on access of cobalt ion to sorption centers to increase of sorption capacity of sorbents. The sorption kinetics of cobalt and the influence of cobalt concentration, pH of various kinds of silica gel matrix with immobilized imidazole group in static conditions on sorption were measured. The sorption of cobalt in various conditions (pH, contact time of phases) with constant liquid-solid ratio (V/m = 50 ml/g) was studied. The distribution coefficients ranged between 200 and 50 000 ml/g (for imidazole), 85 and 120 ml/g (for DB18C6) and between 230 and 500 ml/g (for DA18C6) according to silica gel matrix used and according to the method of sorbent preparation. pH plays important role in the sorption of cobalt on prepared sorbents with immobilized crown ethers due to protonization of crown ethers. Protons significantly competes to sorption of cobalt in acidic solutions. The influence of presence of other heavy or toxic metals (Hg(II), Cd(II), Mn(II), Zn(II), Cu(II), Fe(III), Cr(III), Al(III) and the influence of sodium and potassium on sorption Co(II) from aqueous solutions was investigated. Sorption of cobalt decreases in order Hg > Cu > Cd > Zn, Fe > Mn > Al, Cr. The presence of sodium and potassium ions at concentration 0.05 mol/l significantly influences on the sorption of cobalt with sorbent with immobilized DB18C6 functional group.     

Cu掺杂TiO2及其纳米管的制备、表征与光催化性能

通过溶胶-凝胶法和水热法制备了Cu掺杂TiO₂纳米粉末及其纳米管,并通过XRD、TEM、FE-SEM、EDS、UV-Vis/DRS等手段分析了样品的结构。发现以Cu掺杂TiO₂纳米粉末为水热反应原料制备的纳米管中不含Cu,对其原因进行了分析讨论并通过Zn掺杂TiO₂纳米粉末证实：以金属掺杂TiO₂纳米粉末为原料,通过水热法制备TiO₂纳米管中不含有相应金属离子,这是由于金属离子在强碱水热条件下形成金属配离子,使金属离子溶解于水中而不能形成金属掺杂TiO₂纳米管。对所得样品进行了光催化性能测试,发现：Cu掺杂TiO₂粉末的光催化产氢效率为0.75 μmol·(g·h)^-1,高于由其本身及P25通过水热法制备的TiO₂纳米管(分别为：0.42 μmol·(g·h)^-1,0.25 μmol·(g·h)^-1)的光催化产氢效率。     

The preparation of sol-gel materials doped with ionic liquids and trialkyl phosphine oxides for yttrium(III) uptake

A new material (IL923SGs) composed of ionic liquids and trialkyl phosphine oxides (Cyanex 923) for Y(III) uptake was prepared via a sol-gel method. The hydrophobic ionic liquid 1-octyl-3-methylimidazolium hexafluorophosphate (C₈mim⁺PF₆⁻) was used as solvent medium and pore templating material. The extraction of Y(III) by IL923SGs was mainly due to the complexation of metal ions with Cyanex 923 doped in the solid silica. Ionic liquid was stably doped into the silica gel matrix providing a diffusion medium for Cyanex 923, and this will result in higher removal efficiencies and excellent stability for metal ions separation. IL923SGs were also easily regenerated and reused in the subsequent removal of Y(III) in four cycles.     

New alpha-amino phenylalanine tetrazole ligand for immobilized metal affinity chromatography of proteins

A new chelating compound has been developed for use in the immobilized metal affinity chromatographic (IMAC) separation of proteins. The bidentate ligand, alpha-amino phenylalanine tetrazole, 4, was synthesized via a five-step synthesis from N-fluorenylmethoxycarbonyl phenylalanine and then immobilized onto silica through the epoxide coupling procedure. The binding behavior of the resulting IMAC sorbent, following chelation with Zn2+ to a density of 183 micromol Zn2+ ions/g silica, was characterized by the retention of proteins in the pH range of 5.0-8.0, and by the adsorption behavior of lysozyme with frontal chromatography at pH 6.0 and 8.0. The prepared column showed the separation ability to four test proteins and the retention time of these proteins increased with an increase in pH. From the derived isotherms, the adsorption capacity, qm, for the binding of lysozyme to immobilized Zn2+-alpha-amino phenylalanine tetrazole-silica was found to be 1.21 micromol/g at pH 6.0 and 1.20 micromol/g sorbent at pH 8.0, respectively, whilst the dissociation constants KD at these pH values were 5.22x10(-6) and 3.49x10(-6) M, respectively, indicating that the lysozyme was retained more stable under alkaline conditions, although the binding capacity in terms of micromole protein per gram sorbent remained essentially unchanged.     

Retention of Some Metal Ions and Their Separation on Silica Gel Modified with Acid Red 88

 Acid Red 88 is strongly extracted by chloroform solutions of Aliquat 336 by an ion exchange mechanism and for its reextraction from the ion pair formed, relatively high concentrations of mineral acids are required. By impregnation of silica with the ion pairs between the cation of Aliquat 336 and the anion of the dye a chelating sorbent for metal ions can be obtained. The sorbent prepared may be successfully used for separation of mixtures of various metal ions by the column extraction chromatography technique, additional purification of sodium and potassium salts from ions of heavy metals and for concentration of trace amounts of ions of various metals from aqueous solutions followed by their quantitative determination. The sorbent can be used repeatedly in the process of sorption and desorption of metal ions (especially those forming less stable complexes with the reagent) after regeneration with solutions of perchloric acid. Received January 28, 1998. Revision March 1, 1999.     

Reactivity of Thioglycolic Acid Physically and Chemically Bound to Silica Gel as New Selective Solid Phase Extractors for Removal of Heavy Metal Ions From Natural Water Samples

A method is presented for the immobilization of thioglycolic acid moiety on the surface of active silica gel via a simple and direct synthetic route and based on one step reaction procedure. Two-product solid phase extractors were successfully synthesized according to physical adsorption and chemical immobilization binding techniques, phases (I) and (II), respectively. The mode of interaction between the silanol group and the thioglycolic moiety was also discussed for both phases based on the infrared analysis studies. The thermal stability properties as well as the effect of buffer solutions on the percentage hydrolysis of the two silica gel phases were examined and revealed the high stability and superiority of silica phase (II) in these respects. The evaluation of the selectivity and metal uptake properties incorporated in these two silica gel phases were also studied and discussed for a series of divalent heavy metal ions under different controlling factors. The mmol/g values were found to be higher in case of phase (I). The selective removal and extraction of some heavy metal ions, viz . Cu(II), Zn(II), and Hg(II) from natural seawater samples was successfully accomplished with the percentage recovery values for the three tested metal ions in the range of 96.5-98.4 - 0.2-0.6%. The presence of higher concentrations of Na(I), K(I), Mg(II) and Ca(II) showed insignificant role or no matrix effect on such selective extraction process due to their 0% values of removal by these silica gel phases (I) and (II).     

Synthesis, characterization of silica gel phases-chemically immobilized-4-aminoantipyrene and applications in the solid phase extraction, preconcentration and potentiometric studies.

Two new 4-aminoantipyrene chemically-immobilized silica gel phases: ii (N,N-donor) and iii (N,O-donor), were synthesized and characterized by IR and surface coverage determination. The latter was accomplished by thermal desorption and metal probe methods, giving 0.300 and 0.312 mmol g(-1) for ii and 0.220 and 0.250 mmol g(-1) for iii. Moreover, potentiometric titration provided a surface coverage of 0.323 mmol g(-1) for ii. The metal capacity values in mmol g(-1) of ii, iii and the active silica gel phase i for a series of di- and trivalent metal ions were determined at pH 1.0 - 6.7. Phase i showed the lowest values, while ii and iii reflected higher affinity toward most of the metal ions. The highest values were 0.300 for Hg(II)-ii and 0.220 mmol g(-1) for Cd(II)-iii. Distribution coefficients (log Kd) were in the range of 3.57 - 4.76 for ii and 2.32 - 3.46 for iii, thus confirming certain selectivity characters of the solid extractors. The application of the phases as solid extractors and preconcentrators for some heavy metal ions is presented. Good percentage extraction and removal of 94 - 98 +/- 4 - 6% of the spiked 1.000 microg ml(-1) of Hg(II), Cd(II), Pb(II), Cu(II) and Zn(II) and good percentage recovery of 94 - 99 +/- 3 - 6% of 50 ng ml(-1) of these ions from tap water samples were obtained. Stability constants of H(I) and Cu(II) with ii for the two-phase mixture at 25 degrees C and I = 0.1 (KCI) were determined potentiometrically. The pKa of ii are 5.6 and 8.4, while the log K values for CuHL and CuL (L = ii) are 6.3 and 5.8, respectively, leading to the determination of several analytical data for Cu(II)-ii.     

An ion-imprinted silica-supported organic-inorganic hybrid sorbent prepared by a surface imprinting technique combined with a polysaccharide incorporated sol-gel process for selective separation of cadmium(II) from aqueous solution

Ion-imprinting concept and polysaccharide incorporated sol-gel process were applied to the preparation of a new silica-supported organic-inorganic hybrid sorbent for selective separation of Cd(II) from aqueous solution. In the prepared shell/core composite sorbent, covalently surface coating on the supporting silica gel was achieved by using a Cd(II)-imprinting sol-gel process starting from an inorganic precursor, γ-glycidoxypropyltrimethoxysiloxane (GPTMS), and a functional biopolymer, chitosan (CS). The sorbent was prepared through self-hydrolysis of GPTMS, self-condensation and co-condensation of silanol groups (Si-OH) from siloxane and silica gel surface, in combination with in situ covalent cross-linking of CS with partial amine shielded by Cd(II) complexation. Extraction of the imprinting molecules left a predetermined arrangement of ligands and tailored binding pockets for Cd(II). The prepared sorbent was characterized by using X-ray energy dispersion spectroscopy (EDX), X-ray diffraction (XRD), and scanning electron microscopy (SEM). Batch experiments were conducted to study the sorption performance by removal of Cd(II) when present singly or in binary system, an aqueous Cd(II) and Zn(II) mixture. The ion-imprinted composite sorbent offered a fast kinetics for the sorption of Cd(II) and the maximum capacity was 1.14 mmol g⁻¹. The uptake capacity of the imprinted sorbent and the selectivity coefficient were much higher than that of the non-imprinted sorbent. The imprinted sorbent exhibited high reusability. The prepared functional sorbent was shown to be promising for the preconcentration of cadmium in environmental and biological samples.     

Silica gel-immobilized Eriochrome black-T as a potential solid phase extractor for zinc (II) and magnesium (II) from calcium (II)

The immobilization of silica gel surface with Eriochrome black-T indicator (ERT) for the formation of silica-ERT phase is described. The surface coverage of silica gel, based on carbon and nitrogen analysis of the modified silica gel phase, is 0.38 mmol g(-1). The stability towards hydrolysis of silica-ERT phase in different buffer solutions (pH 1-10) is studied and evaluated. The applicability of silica-ERT as a solid phase extractor for Zn(II), Mg(II) and Ca(II) is studied by the batch equilibrium technique and found to show an order similar to the formation constant values of these three metal ions with the indicator. The selectivity of silica-ERT phase towards the extraction of a certain metal ion from a mixture containing only two metal ions is studied by the batch equilibrium technique and exhibited good discrimination orders for Zn(II) and Mg(II) in presence of Ca(II). The results of the column separation and preconcentration studies are consistent with the selectivity behaviour of silica-ERT phase, thus affording reasonable separation of the three studied metal ions.     

Novel dye-attached macroporous films for cadmium, zinc and lead sorption: Alkali Blue 6B-attached macroporous poly(2-hydroxyethyl methacrylate)

Alkali Blue 6B-attached poly(2-hydroxyethyl methacrylate) (poly(HEMA)) microporous films were investigated as chelate forming sorbents for heavy metal removal. Poly(HEMA) microporous films were prepared by UV-initiated photo-polymerization of HEMA in the presence of an initiator (azobisisobutyronitrile (AIBN)). Alkali Blue 6B was attached covalently. These films with a swelling ratio of 58%, and carrying 14.8 mmol Alkali Blue 6B m(-2) which were then used in the removal of Cd(II), Zn(II) and Pb(II) from aqueous media. Adsorption rates were very high, equilibrium was achieved in about 30 min. The maximum adsorption of heavy metal ions onto the Alkali Blue 6B-attached films were 41.4 mmol m(-2) for Cd(II), 52.4 mmol m(-2) for Zn(II), and 64.5 mmol m(-2) for Pb(II). When the heavy metal ions competed during the adsorption from a mixture the adsorption values for Cd(II), Zn(II) and Pb(II) were quite close. Heavy metal ions were desorbed by using 0.1 M HNO(3). A significant amount of the adsorbed heavy metal ions (up to 95%) could be desorbed in 30 min. Repeated adsorption/desorption cycles showed the feasibility of these novel dye-attached microporous films for heavy metal removal.     

Solid-phase extraction of trace Cu(II) Fe(III) and Zn(II) with silica gel modified with curcumin from biological and natural water samples by ICP-OES

Silica gel was firstly functionalized with aminopropyltrimethoxysilane obtaining the aminopropylsilica gel (APSG). The APSG was reacted subsequently with curcumin yielding curcumin-bonded silica gel (curcumin-APSG). This new bonded silica gel was used for separation, pre-concentration and determination of Cu(II), Fe(III), Zn(II) in biological and natural water samples by inductively coupled plasma optical emission spectrometry (ICP-OES). Experimental conditions for effective adsorption of trace levels of metal ions were optimized with respect to different experimental parameters using batch and column procedures in detail. The optimum pH value for the separation of metal ions simultaneously on the newly sorbent was 4.0. Complete elution of the adsorbed metal ions from the sorbent surface was carried out using 2.0 mL of 0.1 mol L^− 1 of HCl. Common coexisting ions did not interfere with the separation and determination at pH 4.0. The maximum static adsorption capacity of the sorbent at optimum conditions was found to be 0.63, 0.46 and 0.37 mmol g^− 1 for Cu(II), Fe(III) and Zn(II) respectively. The time for 95% sorption for Cu(II) Fe(III) and Zn(II) was less than 2 min. The detection limits of the method defined by IUPAC was found to be 0.12, 0.15 and 0.40 ng mL^− 1 for Cu(II), Fe(III) and Zn(II), respectively. The relative standard deviation (RSD) of the method under optimum conditions was lower 3.0% (n = 5). The procedure was validated by analyzing the certified reference river sediment material (GBW 08301, China), the results obtained were in good agreement with standard values. This sorbent was successfully employed in the separation and pre-concentration of trace Cu(II), Fe(III) and Zn(II) from the biological and natural water samples yielding 75-fold concentration factor.     

Modification of silica nanoparticles with 1-hydroxy-2-acetonaphthone as a novel composite for the efficient removal of Ni(II), Cu(II), Zn(II), and Hg(II) ions from aqueous media

In this paper, a novel composite based on the formation of Schiff base on silica nanoparticles was facilely synthesized. Firstly, silica nanoparticles, which contain silanol groups (Si-OH), were modified with (3-aminopropyl)trimethoxysilane. Then, the modified silica reacted with 1-hydroxy-2-acetonaphthone to form a novel Schiff base/silica composite. The synthesized composite was characterized using several tools such as XRD, FT-IR, FE-SEM, N₂ adsorption/desorption analyzer, and CHN analyzer. The considerable reduction at 2θ = 21.9° in the intensity of the XRD peak of the composite is owing to the formation of the Schiff base. Also, the observed FT-IR bands in the composite at 3440 and 1604 cm^?1 are owing to the stretching and bending vibrations of OH and/or CN, respectively. The FE-SEM images confirmed that the silica includes irregular shapes whereas the composite possesses a flaky surface owing to the formation of the Schiff base. Elemental analysis of the composite demonstrated that the % C, % H, and % N are 15.26, 3.24, and 1.65 %, respectively. The BET surface area and total pore volume of the composite were reduced because the formed Schiff base blocks the pores of silica. The synthesized composite was employed for the efficient removal of Ni(II), Cu(II), Zn(II), and Hg(II) ions from aqueous media. The maximum uptake capacity of the composite toward Cu(II), Hg(II), Zn(II), and Ni(II) ions is 68.630, 50.942, 45.126, and 40.420 mg/g, respectively. The adsorption processes of the studied metal ions were spontaneous, chemical, and well described using the pseudo-second-order kinetic model and Langmuir equilibrium isotherm. The synthesized composite can be successfully regenerated and utilized various times in the removal of studied metal ions from aqueous media.     

A mesoporous 3D hybrid material with dual functionality for Hg2+ detection and adsorption

Dual-function hybrid material U1 was designed for simultaneous chromofluorogenic detection and removal of Hg(2+) in an aqueous environment. Mesoporous material UVM-7 (MCM41 type) with homogeneously distributed pores of about 2-3 nm in size, a large specific surface area exceeding 1000 m(2) g(-1), and nanoscale particles was used as an inorganic support. The mesoporous solid is decorated with thiol groups that were treated with squaraine dye III to give a 2,4-bis(4-dialkylaminophenyl)-3-hydroxy-4-alkylsulfanylcyclobut-2-enone (APC) derivative that is covalently anchored to the inorganic silica matrix. The solid was characterised by various techniques including X-ray diffraction, transmission electron microscopy, Raman spectroscopy, and nitrogen adsorption. This hybrid solid is the chemodosimeter for Hg(2+) detection. Hg(2+) reacts with the APC fragment in U1 with release of the squaraine dye into the solution, which turns deep blue and fluoresces strongly. Naked-eye Hg(2+) detection is thus accomplished in an easy-to-use procedure. In contrast, U1 remains silent in the presence of other thiophilic transition metal ions, alkali and alkaline earth metal ions, or anions ubiquitously present in water such as chloride, carbonate, sulfate, and phosphate. Material U1 acts not only as chemodosimeter that signals the presence of Hg(2+) down to parts-per-billion concentrations, but at the same time is also an excellent adsorbent for the removal of mercury cations from aqueous solutions. The amount of adsorbed mercury ranges from 0.7 to 1.7 mmol g(-1), depending on the degree of functionalisation. In addition, hybrid material U1 can be regenerated for both sensing and removal purposes. As far as we know, U1 is the first example of a promising new class of polyfunctional hybrid supports that can be used as both remediation and alarm systems by selective signalling and removal of target species of environmental importance. Model compounds based on silica gel (G1), fumed silica (F1), and micrometre-sized MCM-41 scaffolds (M1) were also prepared and studied for comparative purposes.     

Preparation of silica-supported porous sorbent for heavy metal ions removal in wastewater treatment by organic-inorganic hybridization combined with sucrose and polyethylene glycol imprinting

A new porous sorbent for wastewater treatment of metal ions was synthesized by covalent grafting of molecularly imprinted organic-inorganic hybrid on silica gel. With sucrose and polyethylene glycol 4000 (PEG 4000) being synergic imprinting molecules, covalent surface coating on silica gel was achieved by using polysaccharide-incorporated sol-gel process starting from the functional biopolymer, chitosan and an inorganic epoxy-precursor, gamma-glycidoxypropyltrimethoxysiloxane (GPTMS) at room temperature. The prepared porous sorbent was characterized by using simultaneous thermogravimetry and differential scanning calorimeter (TG/DSC), scanning electron microscopy (SEM), nitrogen adsorption porosimetry measurement and X-ray diffraction (XRD). Copper ion, Cu²⁺, was chosen as the model metal ion to evaluate the effectiveness of the new biosorbent in wastewater treatment. The influence of epoxy-siloxane dose, buffer pH and co-existed ions on Cu²⁺ adsorption was assessed through batch experiments. The imprinted composite sorbent offered a fast kinetics for the adsorption of Cu²⁺. The uptake capacity of the sorbent imprinted by two pore-building components was higher than those imprinted with only a single component. The dynamic adsorption in column underwent a good elimination of Cu²⁺ in treating electric plating wastewater. The prepared composite sorbent exhibited high reusability. Easy preparation of the described porous composite sorbent, absence of organic solvents, cost-effectiveness and high stability make this approach attractive in biosorption.