层层组装法制备核壳SiO_2/Pt粒子及其CO电氧化和原位电化学FTIR光谱

采用层层组装法合成了核壳SiO2/Pt粒子,用电化学循环伏安法(CV)和原位电化学傅里叶变换红外(FTIR)光谱研究了SiO2/Pt粒子对CO分子的氧化和吸附行为.透射电子显微研究表明:包覆SiO2的Pt壳是由团聚的Pt纳米微粒构成,其平均厚度大约为26nm.CO在SiO2/Pt粒子修饰的玻碳(GC)电极上的主氧化峰为0.49V(vsSCE),表现出比本体Pt金属好的催化性能.电化学FTIR光谱研究发现:线性CO在SiO2/Pt粒子上的IR吸收带的方向发生倒反,而且在不同的研究电位下,每个吸收带劈裂为两个间隔约为14cm-1的吸收带,这种劈裂现象在饱和吸附CO的Pt金属表面上是很难观察到的.这些异常的红外吸收现象可能是由SiO2/Pt粒子的结构效应导致的.     

团聚铂纳米粒子电极在甲醇氧化中的电催化特性

用H2还原法并以Nafion作为稳定剂合成团聚的Pt纳米粒子，附载于玻碳表面制备电催化剂.透射电子显微镜（TEM）和扫描电子显微镜（SEM）表征结果指出,团聚Pt纳米粒子的平均尺寸约为400 nm.运用电化学循环伏安法(CV)和原位傅立叶变换红外反射光谱（in situ FTIRS）研究甲醇的氧化过程，发现团聚Pt纳米粒子电极具有较高的电催化活性.原位FTIRS研究结果检测到甲醇在所制备的电催化剂上氧化的中间体为线型吸附态CO物种，其红外吸收给出异常红外效应的光谱特征.     

碱性介质中甘氨酸在纳米金膜电极上的吸附和氧化

运用原位红外反射光谱（in situ FTIRS）和电化学石英晶体微天平（EQCM）在分子水平上研究了碱性介质中甘氨酸在纳米金膜电极上的解离吸附和氧化过程.结果表明,甘氨酸在很低的电位下（－0.8 V, vs SCE）就可发生解离吸附.其解离产物氰基(CN－)与电极表面存在较强的化学吸附作用，形成AuCN－物种(红外吸收谱峰位于2100 cm－1附近).吸附在纳米金膜表面的CN－给出红外吸收显著增强、红外谱峰方向倒反和半峰宽增加的异常红外效应特征.吸附态CN－在低电位抑制H2O和OH－的吸附，当电位高于0.2 V可氧化产生OCN－；进一步升高电位到0.3 V则形成.溶液相物种OCN－和对应的红外吸收峰分别为2169 cm－1和2145 cm－1.实验结果指出，金以的形式溶解是导致电极表面质量显著减少的主要原因.     

SnO2-TiO2薄膜载体对Au-Pt纳米颗粒电化学性能的影响

采用真空镀膜法在玻碳(GC)电极表面修饰SnO2-TiO2薄膜, 在SnO2-TiO2/GC复合电极表面组装Au-Pt双金属纳米颗粒, 制得Au-Pt/SnO2-TiO2/GC复合电极. 通过循环伏安法(CV)研究了SnO2-TiO2薄膜载体对Au-Pt双金属纳米颗粒电化学性能的影响; 采用扫描电镜(SEM)及X射线光电子能谱(XPS)对Au-Pt在SnO2-TiO2薄膜沉积的形貌及结构进行了表征. 研究结果表明, 10 nm的Au-Pt双金属纳米颗粒均匀地组装于SnO2-TiO2薄膜表面; SnO2-TiO2薄膜载体改善了复合电极抗CO中毒能力; Au-Pt双金属合金的形成提高了Pt 对甲醇氧化的电催化能力, SnO2-TiO2薄膜载体又使Pt纳米粒子d空轨道增多, 提高了Au-Pt双金属纳米颗粒的稳定性和催化性能.     

吸附态和溶液相CO在Pt(110)电极上氧化过程的CV和in situ FTIRS 研究

应用电化学原位傅里叶变换红外反射光谱(in situ FTIRS)研究了酸性介质中Pt(110)单晶电极上吸附态CO(COad)和溶液相CO(COsol)的氧化过程.循环伏安测试表明,COsol氧化的峰电位比COad氧化的正移了168mV,其峰电流密度为后者的6.7倍.电化学原位红外光谱检测到CO主要生成线型的吸附态物种(COL),均匀分布在Pt(110)表面上.当溶液中不存在CO时,COL仅在电位高于0.15V才发生氧化.而且,该谱峰在其稳定吸附的电位区间内随电位增加蓝移,Stark系数为30cm-1·V-1;在COL发生氧化的电位区间,其谱峰强度随电位增加减小、峰位红移,线性变化率为-56cm-1·V-1.溶液中饱和CO时,原位红外光谱在-0.05V即可检测到CO2的存在,显示COL起始氧化的电位提前了200mV;电位高于-0.05V,该谱峰即发生红移,对应的线性变化率为-26.5cm-1·V-1.     

铂纳米粒子电极上NO吸附和还原的CV及原位FTIR研究

运用电化学循环伏安法(CV)和原位傅里叶变换红外反射光谱(in situ FTIRS)研究了酸性介质中铂纳米粒子电极(nm-Pt/GC)上NO吸附及其电催化还原过程.结果表明,NO分子的吸附是电催化还原的重要步骤.在铂纳米粒子电极上饱和吸附的NO存在两种不同键合强度的吸附态,其中弱吸附的NO(NOW)在0.60 V至-0.05 V电位区间还原生成N2O和NH4+;而强吸附的NO(NOS)则在-0.05 V至-0.15 V区间还原,其产物为NH+.     

酸性溶液中过渡金属及合金纳米薄膜电极的异常红外效应研究

以循环伏安方法在玻碳载体上制备纳米级厚度的过渡金属 (Pt,Pd ,Rh ,Ru)和合金 (PtPd ,PtRu)薄膜电极 ,并运用原位FTIR反射光谱研究了CO的吸附过程 .发现所制备的纳米薄膜电极均具有异常红外效应 ,即与本体金属电极相比较 ,吸附在纳米薄膜电极上的CO分子的红外吸收被显著增强 ,并且红外谱峰方向倒反 .本文的结果进一步证明异常红外效应是一种新的、普遍的现象 ,主要取决于过渡金属或合金膜的结构和厚度 .对异常红外效应的深入认识 ,不仅将推动红外反射光谱及界面电化学理论的发展 ,而且将在表面和界面分析中得到广泛应用 .     

纳米金膜电极上CN~-吸附的电化学和原位红外反射光谱研究

应用循环伏安(CV)和原位红外反射光谱(in situFTIRS)研究碱性介质中氰(CN-)在纳米金膜电极(nm-Au/GC)上的吸附行为.结果显示,当研究电极电位低于0.0 V时,CN-可稳定吸附在nm-Au/GC电极表面,高于0.0 V,则发生氧化脱附.发现nm-Au/GC表面具有异常红外效应(AIREs),即吸附态CN-谱峰呈现出与本体Au电极不同的方向倒反、红外吸收增强(39.2倍)以及半峰宽增加的异常光谱特征.本研究将纳米薄膜材料的这一AIREs从过渡金属拓展到币族金属,进一步证明AIREs是迄今研究的金属及合金纳米材料的普遍特性.     

光催化还原制备Au/Ag核壳结构纳米粒子及其修饰电极的电催化性能

以Keggin结构硅钨杂多酸H4SiW12O40(SiW12)为光催化还原剂,通过光化学还原法制备Au/Ag核壳结构纳米粒子. 透射电子显微镜分析显示,所得纳米粒子粒径为30～40 nm,呈均匀分散的球形颗粒,该制备方法的特点是可以较好的避免单金属纳米粒子的形成. 将Au/Ag核壳纳米粒子修饰到具有PVP膜的玻碳电极表面,得到SiW12-(Au/Ag)-PVP多层膜修饰电极. 该修饰电极在0.5 mol/L H2SO4介质中具有良好的电化学响应,在0～-0.75 V电位范围内,出现了3对归属于SiW12的氧化还原峰,且电极性能稳定,灵敏度高. 对H2O2的电催化还原性能明显优于单金属Ag纳米粒子修饰电极,说明Au核的存在可以很好的改善Ag的电催化性能,Au和Ag之间存在相互协同催化作用.     

水溶性的CdSe/ZnS纳米微粒的合成及表征

用L-半胱氨酸(Cys)作为稳定剂，合成了水溶性的CdSe/ZnS核壳结构的半导体纳米微粒。吸收光谱和荧光光谱表明，CdSe/ZnS纳米微粒比单一的CdSe纳米粒子具有更优异的发光特性。透射电子显微镜（TEM）、ED和XPS表征了CdSe/ZnS纳米微粒的结构、分散性及形貌。红外光谱证实半胱氨酸分子中的硫原子和氧原子参加了与纳米粒子表面的金属离子的配位作用。     

纳米结构钴薄膜电极的制备及其异常红外性能研究

用循环伏安电沉积法在玻碳基底上制备纳米结构钴薄膜, 扫描电子显微镜研究结果表明, 纳米结构钴薄膜主要由平均粒径为150 nm的钴粒子组成, 同时还有为数不多的粒径在400~500 nm的钴粒子. 以CO为探针分子, 结合原位傅里叶变换红外反射光谱研究结果, 发现所制备的纳米结构钴薄膜具有异常红外效应. 吸附态CO发生异常红外吸收, 谱峰增强了26.2倍, 测得线型吸附态COL的Stark系数为77.5 cm-1·V-1.     

镍基催化剂上CO和H2O的吸附与反应的红外光谱研究

本文运用红外光谱研究了CO和H_2O在Ni基催化剂上的吸附和反应规律。证实了H_2O在催化剂上是解离吸附, 以OH的形式吸附在催化剂上, 在OH之间可能有氢键形成。CO有两种吸附态: 线式和桥式。预吸附H_2O使CO线式吸附态几乎消失, 桥式吸附峰红移了约30 cm~(-1)。在不同温度时, 对比了CO或表面碳与H_2O的反应, 发现表面碳更容易同水反应生成甲烷。     

Preparation of carbon-supported core-shell Au-Pt nanoparticles for methanol oxidation reaction: The promotional effect of the Au core

Core-shell Au-Pt nanoparticles with intimate contact of Pt and Au were prepared by a displacement reaction without formation of monometallic Au nanoparticles. The Au-Pt nanoparticles were dispersed on carbon (Au@Pt/C) and were used to catalyze methanol electrooxidation in acidic solutions at room temperature. The core-shell nanostructure was confirmed by transmission electron microscopy and X-ray photoelectron spectroscopy, and specific catalytic activities were evaluated by CO anodic stripping voltammetry in 0.5 M H(2)SO(4) and by cyclic voltammetry in 1 M CH(3)OH + 0.5 M H(2)SO(4). The Au@Pt/C catalyst demonstrated enhanced specific activity in methanol electrooxidation and showed multiple CO stripping peaks which were all negatively shifted with respect to a similarly prepared Ag@Pt/C catalyst. The activity enhancement is attributed to the presence of Au underneath a very thin Pt shell where electron exchange between Au and Pt had promoted the formation of active oxygen species on Pt, which facilitated the removal of inhibiting CO-like reaction intermediates.     

The effect of the particle size on the kinetics of CO electrooxidation on high surface area Pt catalysts

Using high-resolution transmission electron microscopy (TEM), infrared reflection-absorption spectroscopy (IRAS), and electrochemical (EC) measurements, platinum nanoparticles ranging in size from 1 to 30 nm are characterized and their catalytic activity for CO electrooxidation is evaluated. TEM analysis reveals that Pt crystallites are not perfect cubooctahedrons, and that large particles have "rougher" surfaces than small particles, which have some fairly smooth (111) facets. The importance of "defect" sites for the catalytic properties of nanoparticles is probed in IRAS experiments by monitoring how the vibrational frequencies of atop CO (nu(CO)) as well as the concomitant development of dissolved CO(2) are affected by the number of defects on the Pt nanoparticles. It is found that defects play a significant role in CO "clustering"on nanoparticles, causing CO to decrease/increase in local coverage, which yields to anomalous redshift/blueshift nu(CO) frequency deviations from the normal Stark-tuning behavior. The observed deviations are accompanied by CO(2) production, which increases by increasing the number of defects on the nanoparticles, that is, 1 < or = 2 < 5 < 30 nm. We suggest that the catalytic activity for CO adlayer oxidation is predominantly influenced by the ability of the surface to dissociate water and to form OH(ad) on defect sites rather than by CO energetics. These results are complemented by chronoamperometric and rotating disk electrode (RDE) data. In contrast to CO stripping experiments, we found that in the backsweep of CO bulk oxidation, the activity increases with decreasing particle size, that is, with increasing oxophilicity of the particles.     

Restructuring-induced activity of SiO(2)-supported large au nanoparticles in low-temperature CO oxidation

Large Au nanoparticles with an average size of approximately 10 nm supported on inert SiO(2) become active in low-temperature CO oxidation after the addition of NaNO(3). The catalyst structures have been characterized in detail by X-ray diffraction, X-ray photoelectron spectroscopy, transmission electron microscopy, and X-ray absorption spectroscopy. The NaNO(3) additive in Au/SiO(2) catalysts does not lead to the formation of fine Au nanoparticles, which are generally considered to be inevitable in low-temperature CO oxidation catalyzed by gold, nor does it alter the electronic structure of Au. The NaNO(3)-induced restructuring of large Au nanoparticles was proposed to create low-coordinated Au sites on the surface capable of catalyzing low-temperature CO oxidation. These results experimentally prove that the activity of supported Au nanoparticles in low-temperature CO oxidation could solely arise from their geometric structure, which greatly deepens the fundamental understandings of Au nanocatalysis.     

Aucore Ptshell纳米粒子对甲醇氧化的电催化性能研究

应用两步化学还原法制备不同厚度的AucorePtshell纳米粒子,经紫外可见光谱(UV-V is)、透射电子显微镜(TEM)表征.该金纳米颗粒经化学还原包裹铂后平均粒径明显增大,调节金与铂的含量可获得不同包裹厚度的AucorePtshell纳米粒子.循环伏安法研究表明,粒径为70~80 nm的AucorePtshell纳米粒子对甲醇的氧化具有较好的电催化活性,并且其电催化性能随着电位循环扫描次数的增加而增强.     

AucorePtshell础纳米粒子对甲醇氧化的电催化性能研究

应用两步化学还原法制备不同厚度的AucorePtshell纳米粒子，经紫外可见光谱（UV-Vis）、透射电子显微镜（TEM）表征．该金纳米颗粒经化学还原包裹铂后平均粒径明显增大，调节金与铂的含量可获得不同包裹厚度的AucorePtshell纳米粒子．循环伏安法研究表明，粒径为70-80nm的AucorePtshell纳米粒子对甲醇的氧化具有较好的电催化活性，并且其电催化性能随着电位循环扫描次数的增加而增强．     

不同尺度和分散状态的钯纳米粒子红外光学性能研究

运用CO分子探针红外光谱研究不同尺度和分散状态的钯纳米粒子的红外光学性能.结果表明,粒子尺度为6.6nm分散的球型钯纳米粒子(Pdn)和粒子尺度为100～150nm分散的立方体型钯纳米粒子(Pdncube)均给出两个不同吸附方式的桥式CO红外谱峰,其吸收峰位置约在1970cm-1和1910cm-1.将Pdn引入到电极表面后,通过界面电化学诱导使之形成团聚体(Pdnag),其红外光学性能发生显著变化,表现为随着界面电化学诱导时间的增加,其1970cm-1处的谱峰方向从正常转为异常.本研究进一步证明红外谱峰方向的倒反是由于粒子间的相互作用引起的.     

Au-Pt双金属纳米颗粒在玻碳电极上的自组装

利用硼氢化钠还原HAuCl4和H2PtCl4的混合溶液, 制备了Au- Pt双金属纳米颗粒. UV- Vis、TEM、ED、XRD、XPS等研究结果表明双金属纳米颗粒为Au- Pt合金. 在玻碳电极上通过有机偶联层半胱氨酸进行了Au- Pt双金属纳米颗粒的自组装, 得到Au- Pt/半胱氨酸/玻碳电极, 并通过SEM对其表面结构进行了表征, 粒子的平均粒径为12.6 nm. 用循环伏安法对Au- Pt/半胱氨酸/玻碳电极的电化学性能进行了测试. 结果表明Au- Pt/半胱氨酸/玻碳电极具有良好的电催化甲醇氧化性能.     

Preparation and UV-light Absorption Property of Oleic Acid Surface Modified ZnO Nanoparticles

Syntheses of zince oxide(ZnO) nanoparticles by direct precipitation and surface modification with oleic acid were reported. ZnO nanoparticles were characterized via X-ray diffractometry(XRD), transmission electron microscopy(TEM), infrared spectroscopy(IR) and UV-Vis spectroscopy. The prepared ZnO nanoparticles were nearly spherical and highly crystalline with an average size of 29 nm. In addition, high UV-light absorption properties of oleic acid surface modified ZnO nanoparticles were successfully obtaine...