ICP-AES法测定镀铝锌钢板镀层中的铝含量

用50g/L的氢氧化钠溶液溶解镀铝锌钢板镀层,以盐酸溶液(1 4)进行酸化,采用ICP?AES法测定两种镀铝锌钢板镀层中的铝含量,测定结果的相对标准偏差分别为2.3%和1.4%(n=11),回收率为94.8%～98.5%。对两种镀铝锌钢板金属中铝含量测定结果的不确定度进行了评定,分别为0.10%(铝含量为4.82%)、0.9%(铝含量为54.3%)。     

锌镍渣中锌的测定

研究了在NaOH-H2O2介质中,Zn与Ni、Cd、Cu等大部分金属离子分离,以二甲酚橙为指圣剂,在pH 5.0～6.0用Na2EDTA滴定锌的分析方法.研究确定了最佳的试样条件,用于锌镍渣中锌(6.52%～89.68%)的测定,其相对标准偏差为(0.45%～2.20%),加标准回收率锌在(96.67%～99.87%)之间.     

稀土在电沉积锌—镍合金中的作用

锌—镍合金镀层具有耐蚀性高、低氢脆性和与基体的结合力好等特性 ,是良好的防护性镀层。当合金镀层的镍含量在 7～ 1 8% (质量 )时 ,镀层的耐蚀性最高 ,因此它可代替传统的锌镀层、锡镀层和镉镀层而广泛应用于电镀汽车钢板、航空航天及家电等行业[1～ 3] 。稀土元素 ( RE)包括了 1 5个镧系元素和钇元素 ,共 1 6个元素。由于稀土元素具有独特的电子层结构和化学性能 ,使稀土及其化合物在材料科学领域中的应用越来越广泛 ,尤其是稀土在电沉积过程中的研究及应用正日趋深入。文献资料表明 ,在电镀溶液中加入少量的稀土化合物后 ,可以改善镀液…     

ICP—AES法同时快速测定镀铝锌薄板镀层中铝和锌

镀铝锌钢板的防锈能力一般为传统镀锌钢板的四倍以上。生产厂家要求将样品完全溶出其表面镀层铝锌等合金,同时最大限度地不溶出基钢,并测定溶出镀层合金中铝和锌的质量分数。     

化学法测定锌铁合金钢板镀层中铁含量测量结果的不确定度评定

对用化学法测定锌铁合金钢板镀层铁含量测量结果的不确定度进行评定,分析了该方法测定过程的不确定度来源主要是分析锌铁合金钢板镀层中铁质量的不确定度和分析锌铁合金钢板镀层质量的不确定度,建立数学模型并计算了各不确定度分量,经合成得标准不确定度为0.21%,扩展不确定度为0.42%(k=2).     

碱性电镀光亮锌镍合金研究

在总结镀液的电化学特性和锌镍合金镀层的晶体结构与性能等实验结果的基础上,提出碱性电镀光亮锌镍合金的工艺规范和直接把锌酸盐镀锌液转化为碱性电镀光亮锌镍合金镀液的方法。生产实践证明,该工艺稳定,镀层光亮、耐腐性好、硬度较高、无氢脆,镍含量可在９～２０ｗｔ％范围内随意控制。     

三种添加剂对纳米晶锌镀层电沉积行为及结构的影响

运用极化曲线、XRD和SEM研究了三种有机添加剂对酸性硫酸盐溶液中锌电沉积行为以及纳米晶锌镀层结构的影响.结果表明,十六烷基三甲基溴化铵(CTAB)、4-苯基-3-丁烯-2-酮(BA)和聚乙二醇(PEG)三种添加剂之间具有较强的协同作用,采用三者组成的混合添加剂可制备出光亮致密的纳米晶锌镀层.镀层晶粒细化的主要原因在于混合添加剂可有效提高锌的沉积过电位,使锌沉积过程中的晶核形成速率增大.     

EDTA滴定法测定再生锌原料中的锌含量

采用氟化铵-盐酸-硝酸-硫酸分解样品,氨水沉淀分离铁、锰、铅等共存元素,滤液中加入掩蔽剂掩蔽少量干扰元素,在pH=5～6的乙酸-乙酸钠缓冲溶液中,以二甲酚橙为指示剂,用EDTA标准滴定溶液滴定。测得结果为锌、镉合量,扣除镉量,即为锌量。方法用于测定再生锌原料中锌,结果的相对标准偏差(RSD,n=11)为0.15%～1.0%。按照实验方法对再生锌原料样品进行加标回收实验,回收率为99.1%～102%。能满足日常对再生锌原料中锌含量的检测要求。     

电感耦合等离子体原子发射光谱(ICP-AES)法测定再生锌原料中铜、铅、铁、铟、镉、砷、钙、铝

采用硝酸、盐酸、氢氟酸(氟化氢铵)、高氯酸分解样品,电感耦合等离子体原子发射光谱法测定了再生锌原料中铜、铅、铁、铟、镉、砷、钙、铝的量。其测定范围:ω(Cu):0.01%～0.60%;ω(Pb):0.10%～5.00%;ω(Fe):0.10%～5.00%;ω(In):0.0100%～0.200%;ω(Cd):0.010%～3.00%;ω(As):0.10%～2.00%;ω(Ca):0.10%～10.00%;ω(Al):0.10%～4.00%。各元素的加标回收率为93%～113%。方法准确、快速、可靠,适用于再生锌原料中铜、铅、铁、铟、镉、砷、钙、铝量的同时测定。     

返滴定法测定含镍锌物料中的锌含量

使用盐酸-硝酸-硫酸将试样溶解,并在氨性条件下过滤,沉淀分离大量共存元素,加入掩蔽剂掩蔽滤液中的干扰元素,在pH=5.5～6.0的缓冲溶液中,选用二甲酚橙作为指示剂,加入过量的EDTA标准滴定溶液,静置使之与溶液中的镍、锌等金属离子充分络合,用氯化锌标准滴定溶液滴定过量的EDTA。测得结果为锌、镉、镍合量,扣除镉、镍量,即为锌量。用来测定含镍锌物料中的锌,其结果的相对标准偏差(RSD,n=11)为0.21%～0.87%,加标回收率为99.0%～102%,满足日常检测需求。     

Optimization of parameters for semiempirical methods. III Extension of PM3 to Be,Mg, Zn,Ga, Ge,As, Se,Cd, In,Sn, Sb,Te, Hg,Tl, Pb,and Bi

Using a recently developed procedure for optimizing parameters for semiempirical methods,¹ PM3 has been extended to a total of 28 elements. Average ΔH_f errors for the newly parameterized elements are Be: 8.6, Mg: 8.4, Zn: 5.8, Ga: 14.9, Ge: 11.4, As: 8.5, Se: 11.1, Cd: 2.6, In: 11.3, Sn: 9.0, Sb: 13.7, Te: 11.3, Hg: 6.8, Tl: 6.5, Pb: 7.4, and Bi: 10.9 kcal/mol. For some elements the paucity of data has resulted in a method, which, while highly accurate, is likely to be only poorly predictive.     

Prediction of the enthalpy of vapourisation for anhydrides,formates, acetates,propionates, butyrates,esters, and ethers

Four analytical correlations based on the use of the corresponding states principle were used to calculate the enthalpy of vapourisation of fluids. Three of these correlations require as inputs the critical temperature and the acentric factor. The fourth requires a molecular Lennard–Jones parameter and the acentric factor. Results for 184 polar and non-polar fluids grouped into 9 families are compared with the values accepted by the Design Institute for Physical Property (DIPPR) project. Recommendations are given for the use of each model and for the choice of the adequate model for each family of fluids.     

ICP-AES法测定铝中铁、硅、铜、镓、镁、锌、锰和钛

用 50g L氢氧化钠溶液溶解铝样品 ,硝酸 (1 1 )酸化 ,以ICP AES测定其中铁、硅、铜、镓、镁、锌、锰和钛等 8种杂质元素。     

ICP-MS测定化妆品中铍、镉、铊、铬、砷、碲、钕、铅

目的：建立化妆品中铍、镉、铊、铬、砷、碲、钕、铅8种有害元素的测定方法。方法：采用电感耦合等离子体质谱法,样品采用微波消解,以钇、锂、铟、铋为内标作定量分析。结果：各元素和内标元素在一定浓度范围内的质量数比值均与浓度呈良好的线性关系,线性方程的相关系数均大于0.9998,平均回收率为95%~104%,相对标准偏差(RSD)均小于3%。结论：该方法灵敏度高,准确,可为化妆品中上述元素的限量检查提供参考。     

猪胰脏中铁钙镁铜铅锌镉锰钴镍的测定

采用硝酸－过氧化氢在自动回流消化仪中消化猪胰脏,火焰原子吸收光度法测定铁、钙、镁、铜、锌、铅、镉、锰、钴、镍的含量。,方法简便,快速,结果令人满意,并对猪胰脏食用价值进行了评价。     

Thin-layer chromatographic separation of aldrin,dieldrin, γ-hexachlorocyclohexane,malathion, ethyl-parathion,pentachlorophenol, and of chlordane,dieldrin, γ-hexachlorocyclohexane,malathion, ethyl-parathion,and pentachlorophenol from each other

A thin-layer chromatographic method is reported for the separation of aldrin (or chlordane), dieldrin, γ-hexachlorocyclohexane, malathion, ethyl-parathion, and pentachlorophenol from each other. The procedure, however, does not separate aldrin and chlordane from each other although it does separate either pesticide from the other components. The method employs alumina plates with n-hexane:xylene:benzene:toluene:cyclohexane:methyl cyclohexane (50:50:50:50:50:50:) as developing solvent.     

Enthalpies of dilution of aqueous solutions of formamide,acetamide, propionamide,andN,N-dimethylformamide

The enthalpies of dilution of aqueous solutions of formamide, acetamide, propionamide,N,N-dimethylformamide, and sucrose have been measured from about 0.15 to 2.0 moles-kg ^–1 at 25.0°C. The results of the enthalpy measurements were used to calculate the pairwise enthalpies of interaction for each compound with itself. The equation of Savage and Wood together with their interaction parameters are used to predict the experimental results. All of the predictions are within the standard deviation of the original correlation of Savage and Wood (±220 J-kg-mole ^–2 ). Detailed examination of the results shows that specific effects are present but they are less than 220 J-kg-mole ^–2 . Results on urea and substituted ureas are used to determine interaction coefficients for a urea group with itself and with another CH ₂ group. The result,H _U,U =–280 andH _{U,CH 2} =29 J-kg-mole ^–2 , is an improvement on the previous arbitrary assignment of parameters for urea interactions.     

Theoretical Study of Molecular Structure,Reactivity, Lipophilicity,and Solubility of N-Hydroxyurea,N-Hydroxythiourea,and N-Hydroxysilaurea

Ab initio molecular orbital methods at the CBS-QB3 level of theory have been used to study the structure and gas-phase stability of various tautomers and rotamers of N-hydroxyurea, N-hydroxythiourea, and N-hydroxysilaurea, their anions and protonated forms. The geometries of N-hydroxyurea, N-hydroxythiourea, and N-hydroxysilaurea, their anions and cations were optimized at the Becke3LYP/CBSB7 level of theory. For all compounds studied, the amidic form is computed to be substantially more stable than the iminolic tautomer. N-Hydroxyurea and its thio and sila derivatives are computed to behave as Nacids in the gas phase. These compounds are in gas-phase weak acids with a calculated acidity of about 1425 to 1355 kJ-mol^–1. Basicities increase in the order: N-hydroxyurea < N-hydroxythiourea < N-hydroxysilaurea. The most stable protonated structures are represented by several isomers with almost equal stability. Thus, in the N-hydroxyurea, N-hydroxythiourea, and N-hydroxysilaurea, both protonation at the double bonded (C=O, C=S and Si=O) oxygen and sulfur atoms, as well as the protonation at the N(H)OH nitrogen basic center is equally probable. The experimental pK _a value (10.6) of N-hydroxyurea and the computed value (9.7) for its monohydrated complex with the specifically hydrogen-bonded water molecule to the ionizable OH group are in a good agreement. The experimental partition coefficient of N-hydroxyurea is best reproduced by the Alog P_s method. The formation of nitroxide radical in the reaction of N-hydroxyurea and its sulfur and silicon substituted derivatives with the phenol radical is an exothermic process. Thus, the \bondN(H)OH moiety of these compounds may quench the structurally related tyrosyl radicals in the active site of ribonucleotide reductase.