新型纳米光催化剂La3+/S/TiO2的制备及其可见光活性研究

采用沉淀-浸渍法合成了一种新型La^3＋和S共掺杂TiO2纳米复合光催化剂。通过紫外．可见（UV-Vis）漫反射、X射线衍射（XRD）和透射电子显微镜（TEM）等手段对其物相组成、晶粒尺寸、结晶形态和吸光性能进行了表征。以活性艳蓝198染料溶液为模拟废水，对La^3＋／S/TiO纳米复合光催化剂的活性进行了评价。相对于单一的TiO2，S掺杂的TiO2和La^3＋掺杂的TiO2光催化剂，La^3＋／S/TiO2纳米复合光催化荆颗粒的粒径更小，光的吸收边发生了更大程度的红移。在波长λ〉400nm的可见光光照下，具有最高的光催化活性。     

Sm掺杂对TiO2薄膜光催化性能的影响

 采用溶胶-凝胶法、浸渍-提拉法制备了不同形式和不同含量Sm掺杂的锐钛矿晶型TiO2的光催化剂薄膜. 采用X射线衍射、UV-Vis光谱及电化学实验对所制得的TiO2光催化剂薄膜进行了表征,并通过甲基橙溶液的光催化降解实验评价了其光催化活性. 结果表明,与未掺杂的TiO2薄膜相比,Sm掺杂的TiO2薄膜的UV-Vis吸收光波长向长波方向移动,并且光照开路电压也相应提高; 适量Sm掺杂可以明显提高TiO2薄膜的光催化活性,最佳Sm掺杂量为x(Sm3+)=0.5%; 在各种掺杂形式中以表层Sm掺杂的Sm-TiO2(S)薄膜的光催化活性最好. 讨论了Sm掺杂提高TiO2薄膜光催化活性的机理.     

掺杂金属离子改性的TiO2薄膜光催化剂的研制

采用溶胶-凝胶法制备TiO2薄膜光催化剂，着重考察了掺杂铈、镧、钨等金属离子改性的TiO2薄膜的光催化活性，研究了其紫外-可见光透过性能，甲基橙水溶液的光催化降解实验表明：掺杂铈、镧、钨三种金属离子后，TiO2薄膜的光催化活性均有不同程度的提高，最佳掺杂浓度分别为3．0％、1．0％、0．5％，其中掺杂铈的TiO2薄膜光催化活性最高。     

钒离子掺杂对TiO2光催化剂薄膜催化活性的影响

采用溶胶凝胶工艺在普通玻璃表面制备了钒离子非均匀掺杂的TiO2薄膜,运用XRD研究了其光催化复合薄膜的表面特征.以光催化降解甲基橙溶液为模型反应,表征薄膜的光催化活性,结果表明,将钒离子富集在TiO2薄膜内部时,最佳掺杂浓度为1.0%(V/Ti原子百分比),最佳降解表观速率常数为7.44×10-3min-1,约是纯TiO2的2.3倍,有效地提高了TiO2半导体的光催化效率.通过XPS与电化学方法进行分析,说明将钒离子富集在TiO2薄膜内部十分有利于电子-空穴的分离,增强了光生电子与空穴的分离效率.     

金属离子掺杂的TiO2薄膜的制备及其光催化降解甲苯的性能

 采用溶胶-凝胶法制备了负载于铝板上掺杂金属离子的TiO2薄膜光催化剂,并通过空气中甲苯光催化降解实验评价了其光催化活性. 结果表明,Pt和Fe的掺杂对TiO2薄膜的光催化活性起促进作用,甲苯降解率分别提高了17%和6%; Ag的掺杂引起催化剂失活; Mn的掺杂未对TiO2薄膜的光催化活性起明显促进作用. XRD结果表明,掺杂金属离子前后TiO2均为锐钛矿相; TEM观察到薄膜催化剂微观结构为球形颗粒,粒径分布均匀,平均粒径为19 nm; 紫外漫反射光谱表明,Pt-TiO2薄膜催化剂的反射率几乎为0,表明其对光的吸收能力很强,因而Pt掺杂的TiO2薄膜光催化降解甲苯的活性最高.     

掺Ce^3＋纳米TiO2的制备及光催化性能

用溶胶-凝胶法技术制备了掺杂Ce^3＋的纳米TiO2复合粒子，并对其进行了XRD，TEM和DRS表征及光催化活性检验。水中苯酚的Ce^3＋／TiO2光催化降解效果和矿化率分别采用降解率和COD表征。结果表明，未经掺杂的TiO2与掺杂Ce^3＋的TiO2均为锐钛和金红石的混合晶型；掺杂抑制了TiO2晶粒的生长，使得TiO2粒径明显变小，其颗粒大小为10mm左右。用DRS表征微粒的光吸收能力和光吸收带边移动情况，发现掺杂导致了TiO2光吸收能力增强及吸收带边红移。通过对苯酚的光催化氧化降解研究，发现铈的掺杂量有一适宜值，当Ce^3＋在0．08％-0．4％之间时，随着掺杂量的增加光催化活性提高；当Ce^3＋在0．5％～3．0％之间时，随着掺杂量的增加光催化活性降低；Ce^3＋=0．4％时，TiO2光催化活性最高。     

控制胶体合成法制备掺铁TiO_2粉末及光催化降解甲基橙

分别采用控制胶体合成法和溶胶-凝胶法制备了2种不同掺铁方式的TiO2粉末,并用XRD、TEM、BET、UV-Vis、FS等技术对样品进行了表征。在紫外光照射下,以甲基橙溶液的光催化降解反应为探针,研究了掺Fe离子浓度、包覆的次数、不同掺杂方式对样品光催化活性的影响。结果表明,以均匀掺铁TiO2(铁含量大于0.02mol%)干凝胶粉末为载体,采用控制胶体合成法制备了具有P-N结型结构的非均匀掺铁TiO2粉末,其光催化活性较均匀掺杂TiO2粉末明显提高,并且随着包覆次数(≤3次)的增加而增强,以0.04mol%掺铁TiO2粉末包覆3次后制备的样品具有最佳光催化活性,其表观速率常数是未掺杂的TiO2粉末的5.32倍,是具有相同Fe含量的均匀掺杂TiO2粉末的4.58倍。     

Fe3+离子对二氧化钛光电化学催化性能的影响

应用电化学阳极氧化法制备Ti上多孔状纳米晶TiO2薄膜，以及不同Fe^3 离子掺杂量的二氧化钛薄膜．研究了Fe^3 离子掺杂对二氧化钛薄膜吸收光谱和光催化活性的影响，发现Fe^3 的掺杂使薄膜的吸收带边发生红移，在可见光照射下其光催化活性也有一定的提高．     

稀土元素掺杂对TiO2薄膜光催化性能的影响

采用Sol-Gel法、浸渍-提拉法制备了RE(Sm, Dy, Lu) 掺杂TiO2的锐钛矿晶型薄膜. 用X射线衍射分析、 UV-Vis透射光谱及电化学实验对其进行了表征, 通过对紫外光照射下甲基橙溶液的光催化降解评价了其光催化性能. 结果表明, RE掺杂的TiO2薄膜的吸收光向长波方向移动; 掺杂浓度是影响光催化活性的重要因素; 适量RE掺杂可以明显提高TiO2薄膜的光催化性能; 最佳掺杂浓度是0.5%. 其中掺杂Sm样品的光催化活性最好. 分别讨论了RE不同浓度及不同元素掺杂对TiO2光催化性能的影响机制.     

锰离子控制掺杂二氧化钛薄膜光催化活性增强的机理探讨

采用溶胶-凝胶法通过工艺控制制备了锰离子以不同形式掺杂TiO2的光催化剂薄膜,并通过XPS和SEM对薄膜的结构进行表征.通过UV-Vis分光光度计及电化学工作站表征了薄膜的光吸收性能和光电化学性能,通过甲基橙溶液的光催化降解脱色率来表征催化剂薄膜的光催化活性.结果表明,以锰离子MT掺杂方式制备的TiO2薄膜可明显增强TiO2的光催化活性,而以MM掺杂方式制备的TiO2薄膜反而降低了TiO2的光催化活性;锰离子MT掺杂方式的最佳掺杂质量分数为0.8%.催化剂薄膜的电化学行为显示,薄膜具有p-n结的电容-电压特性,锰离子MT掺杂TiO2薄膜的开路电位和瞬时光电流信号较强,说明其光生载流子易于生成并且分离效果较好.依据半导体的p-n结原理探讨了锰离子控制掺杂TiO2的光催化活性机理.     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.     

Synthesis of N-substituted carbazolones from α-iodo enaminones via Pd(0)-catalyzed intramolecular coupling under microwave irradiation

A variety of N-aryl and N-alkyl carbazolones were conveniently achieved in good to high yields via Pd₂(dba)₃-mediated intramolecular coupling of N-substituted α-iodo enaminones under microwave irradiation. The Pd(0)-catalyzed cyclization was found to proceed favorably with the more electron-deficient phenyl ring during the reactions involving unsymmetrical N,N-diaryl α-iodo enaminones. This unique property enables the construction of carbazolone skeleton containing nitro substituted benzenoid ring.     

Synthesis of substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles by intramolecular nitrilimine cycloaddition

Both substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles have been synthesized by the 3+2 intramolecular dipolar cycloaddition of nitrilimines to alkynes. This cyclization has been extended to more versatile 3-bromo derivatives by the use of alkynylbromides as dipolarophiles.     

Catalyst free,visible-light promoted photoaddition reactions between C60 and N-trimethylsilylmethyl-substituted tertiary amines for synthesis of aminomethyl-1,2-dihydrofullerenes

An efficient and benign method for the preparation of aminomethyl-substituted fullerenes has been developed. The process, involving catalyst free, visible-light irradiation of 10% EtOH-toluene solutions containing fullerene C₆₀ and N-trimethylsilylmethyl-substituted amines by using a 20 W compact fluorescent lamp, leads to formation of aminomethyl-substituted fullerene adducts in a highly efficient manner. The photoaddition reaction takes place via a pathway initiated by visible light absorption by C₆₀, followed by SET from the amine to the triplet excited state of C₆₀. Ethanol-promoted desilylation of the resulting a minimum radical then generates the corresponding α-amino radical which couples with the C₆₀ radical anion to form the anion precursor of the fullerene adducts. The new approach using visible-light takes place under mild conditions and it does not require the use of photocatalysts. Thus, the method developed in this effort could broadens the range of functionalized fullerene derivatives that can be readily prepared.     

Highly efficient and stereoselective cycloaddition of nitrones to indolyl- and pyrrolylacrylates

The reactions of various nitrones with indolyl- and pyrrolylacrylates proceeds regioselectively with high diastereoselectivity in the case of aldonitrones, and represents an effective method for obtaining new indolyl- and pyrrolyl-substituted isoxazolidine carboxylates stabilized by weak (CH?O) and moderate (NH?N) strength intramolecular hydrogen bonding. The resulting cycloadducts exhibit promising in vitro anti-influenza activities.     

Transition metal-free direct amination of benzoxazoles using formamides as nitrogen sources

A transition metal-free method for the direct amination of benzoxazoles using formamides as nitrogen sources is reported, which was mediated by an inexpensive and environmentally friendly tetrabutylammonium iodide/tert-butyl hydroperoxide system and gave the 2-aminobenzoxazole derivatives with moderate to good yields.     

l-Proline-catalyzed five-component domino reaction leading to multifunctionalized 1,2,3,4-tetrahydropyridines

Multifunctionalized 1,2,3,4-tetrahydropyridines are concisely synthesized in good yields via l-proline-catalyzed or l-proline/FeCl₃-cocatalyzed one-pot multicomponent reactions (MCRs). The MCRs involve a domino hydroamination/prins reaction/Mannich-type reaction/intramolecular dehydration-cyclization process. The molecular structure of 5baa, one of multifunctionalized 1,2,3,4-tetrahydropyridines, was confirmed by single-crystal X-ray diffraction.     

Exploring the scope of the Gewald reaction: Expansion to a four-component process

An efficient four-component reaction was developed to take advantage of the reactivity of the 2-aminothiophene-3-carbonitrile functionality, which is obtained during the classical three-component Gewald reaction. Various α-methylene bearing ketones were reacted with malononitrile, elemental sulfur, and aryl/heteroarylnitrile derivatives in t-BuOH/NaOH to afford 2-arylthieno[2,3-d]pyrimidin-4-amines in high yields. Preliminary studies revealed the photophysical properties of the products and their potential for use as metal sensors.