Coalescence in crude oil emulsions investigated by a light transmission method

Using a strong light source and a sensitive detector the light transmission of crude oil emulsions can be measured. A semi-empirical theory describes how the measured optical density results from the interaction of absorption and scattering. Changes in the scattering can be used to investigate the coalescence effects caused by demulsifiers. The method is of use in testing demulsifier effectiveness.     

An experimental technique for characterizing dispersion in compounds of particulates in thermoplastics using small-angle light scattering

An experimental technique based on small-angle light scattering for characterizing dispersion of particles and presence of agglomerates in compounds of minerals in thermoplastics is described. The technique is critically discussed in terms of the Mie and Rayleigh-Gans theories of scattering. An experimental study of dispersion in compounds of polypropylene and polystyrene with calcium carbonate by mixing variously on two roll mills, an internal mixer, and a modular intermeshing co-rotating twin screw extruder.     

The spinnability of viscoelastic solutions of tetradecyl- and hexadecyl-trimethylammonium salicylates

The spinnability was measured for aqueous viscoelastic solutions of tetradecyl- and hexadecyltrimethylammonium salicylates (C₁₄TASal, C₁₆TASal) in the absence and presence of sodium salicylate (NaSal) and sodium bromide (NaBr). The spinnability is classified into two types, D and C. While the intrinsic drawing length in type D is proportional to the drawing velocity, the drawing intrinsic length in type C decreases with the drawing velocity or is independent of it. The spinnability changes from type D to C, as the drawing velocity and the surfactant concentration increase, and the temperature lowers. The effect of salt is different between NaSal and NaBr. It can be assumed that a pseudo-network structure composed of rod-like micelles is formed in viscoelastic and spinnable surfactant solutions. Then, the spinnability depends on the balance between the elasticity and the viscosity in which the structure results.     

Thermodynamic consideration on the interface formation of water and ethylene glycol isobutyl ether mixture

The interfacial tension of the binary two-phase mixture of water and ethylene glycol isobutyl ether (EIB) was measured as a function of temperature in the vicinity of the lower critical solution temperatureT _c under atmospheric pressure. The interfacial tension decreased with decreasing temperature and approached zero atT _c . The thermodynamic quantities of interface formation were evaluated by applying equations developed previously to the interfacial tension vs temperature curves. The results were compared with those of the water and diethylene glycol diethyl ether system examined previously, and the effect of the molecular structure of the ether molecule on its interfacial behavior was discussed. It was suggested that the hydration of the ethylene oxide groups of ether molecules was an important factor in the interface formation as well as in the mixing of component molecules of the systems investigated here.     

Optical determination of the thickness of single planar thin lipid films using the symmetrical three-layer model

The total thickness of thin lipid films can be determined by the method of absolute or relative reflectance measurements. The film is described by the symmetrical three-layer model. By assuming equal refractive indices for the hydrocarbon layer and for the organic solution, the thickness and refractive index of the head group layer can be estimated.     

The thermorheological complexity of photoelastic behaviour of 2-hydroxyethyl methacrylate — dodecyl methacrylate copolymers

The viscoelastic photoelastic behaviour of networks of 2-hydroxyethyl methacrylate — dodecyl methacrylate (DMA) copolymers in the main transition and rubberlike region was investigated. With increasing DMA content, photoelastic functions are quickly shifted to lower temperatures or shorter times; a detailed course of the functions suggests heterogeneity of the copolymers. Due to the existence of long side chains, optical function of all samples change the sign from positive to negative with increasing temperature. While the temperature dependences of the moduli of copolymers can be described by the two-phase Takayanagi model, the temperature dependences of optical functions cannot be described by using this model. It has been found, however, that the tempeature and time dependences of photoelastic functions can be described semiquantitatively by a three-phase model with a hypothetical statistical copolymer as the third component. The high values of the volume fraction of the hypothetical statistical copolymer found for the individual samples, suggest a considerable miscibility and a strong influence of the interphase boundary on the photoelastic behaviour of the copolymers.     

Thermomechanical degradation of macromolecules

Extensional flow techniques are used to investigate thermomechanical scission of polymer solutions from ambient temperatures up to 150°C. We report precise central scission of chains beyond a critical fracture strain-rate. These results can be well accounted for by a Thermally Activated Barrier to Scission (TABS) model. We speculate upon the origin of degradation in simple shear flows and report novel results on degradation in porous media and ultrasonic sound fields, which contain dominant extensional components. Finally, we show how the nature and degree of degradation is affected by concentration and polydispersity. In semi-dilute entangled solutions, the degradation rates increase, are much higher for polydisperse solutions and the scission becomes progressively more random along the chain.Dedicated to Professor H. H. Kausch on the occasion of his 60th birthday     

Effect of coexistent hydrocarbon phase on the volume behavior of adsorbed film and micelle of dodecyltrimethylammonium chloride

Interfacial tension () between aqueous dodecyltrimethylammonium chloride (DTAC) solution and benzene was measured as a function of pressure (p) and concentration. The/p was observed to change discontinuously at the critical micelle concentration; this indicates that the micelle formation of DTAC in the aqueous solution coexisting with benzene can be treated like the appearance of a macroscopic phase. It was shown by drawing the vs.A curves that hydrocarbon, such as benzene, cyclohexane, and hexane, make the adsorbed film of DTAC expand. The volume behavior of the micelle with benzene molecules solubilized was found to bear a strong resemblance to that of the adsorbed film at the water/benzene interface. The difference in the molar volume value of adsorbed DTAC among the coexistent hydrocarbon phases was attributed to the difference in the contribution of the hydrocarbon molecules to the interfacial excess volume; the number of the solubilized hydrocarbon molecules was evaluated to be one or two a micelle.     

Thermo-optical analysis as a complementary method in the study of phase transitions of thermotropic liquid crystalline polymer and its blends with polycarbonate

Differential scanning calorimetry (DSC) and thermo-optical analysis (TOA) were applied to study the phase transitions phenomena of thermotropic liquid crystalline polymer and its blends with polycarbonate. It was found that both methods are complementary. Glass transition temperatures of the blends of polycarbonate with liquid crystalline polymer were measured and discussed.     

Swelling of sodium acrylate gels

The swelling process of sodium acrylate gel is experimentally investigated. It is found that sodium acrylate gels weakly crosslinked with N,N-methylene-bis-acrylamide may undergo volume phase transition and that different kinds of mechanical instabilities occur in sequence at the transition. Peculiar wrinkle patterns appear on the free surface of an unstable gel and are changed in geometry as swelling proceeds. Cellular patterns seen at various instances in the late period of swelling are ascertained to be geometrically similar to each other and different only in size. The radii of spherical acrylate gels allowed to swell in water are measured as functions of time. The results are discussed and compared with the kinetic theories of swelling. As a result, these theories are proved to be unsatisfactory to fully describe the experimental facts.     

Photochemically induced phase transitions in the system cetyltrimethyl-ammonium bromide-water containing N-methyl-N,N-diphenylamine

Phase transition temperatures from lyotropic liquid crystals to the isotropic micellar solution of the system cetyltrimethylammonium bromide-water (CTAB-H₂O) were measured in the presence of 0.1-0.9 weight % of N-methyl-N,N-diphenylamine (MPA). They were determined by optical and viscometric methods and were found to increase as a function of MPA concentration in solutions containing 21 and 23 weight % of CTAB. This effect was reversed when MPA was in situ photochemically converted to N-methylcarbazole, allowing photochemically induced phase transitions.     

The viscoelasticity of spinnable solutions of alkyltrimethylammonium salicylates

The viscoelasticity has been measured for aqueous solutions of tetradecyl-and hexadecyltrimethylammonium salicylates (C₁₄TASal, C₁₆TASal). The aqueous solutions of C₁₄TASal without salt displayed the gel-like behavior at 10.0×10^–2 g cm^–3, but those more dilute than 3.2×10^–2 g cm^–3 presented the viscoelasticity similar to that of a Maxwell liquid. The Maxwell-like behavior was converted to the polymer-like one on the addition of (0.1–0.2) M NaBr or (0.02–0.2) M NaSal. The gel-like viscoelasticity can be connected with the spinnability of cohesive fracture failure, and the Maxwell-like and polymer-like viscoelasticities are concerned with the spinnability of ductile failure. The gel-like and Maxwell-like viscoelasticities originate in the pseudo-network formed by the pseudo-linkages between rodlike micelles, while the polymer-like viscoelasticity is caused by the entanglement of long rodlike micelles in semidilute and concentrated solutions. The aqueous solutions of C₁₆TASal behaved very similar to those of C₁₄TASal.     

Thermal and electrical studies of some polychelates

Polychelates of Mn(II), Fe(II), Co(II), Ni(II), and Cu(II) with 4,4′-dihydroxy-3,3′-diacetylbiphenyl-dithioxamide (DDBDO) have been prepared. Their structures were determined by visible reflectance spectroscopy and magnetic measurements in conjunction with thermogravimetric and IR measurements. Elemental analysis indicates a 1∶1 metal-ligand stoichiometry and the association of water molecules with the central metal. The decomposition temperature of the chelates is in the order Ni(II)>Fe(II)>Co(II)>Mn(II)>Cu(II). Thermal activation energies (E _a ), calculated with the help of Freeman-Carroll and Sharp-Wentworth methods, are in agreement with each other. The polychelates were found to be semiconductive, and the activation energy obtained from semiconducting behavior follows the order Co(II)>Ni(II)>Fe(II)>Cu(II)>Mn(II). The probable structure, such as six coordinated octahedral for Mn(II) and Fe(II) polychelates and four coordinated square planar for Co(II), Ni(II), and Cu(II) polychelates, have been suggested.     

Properties of aqueous solution of sodium glycocholate and a nonionic surfactant,and their mixtures

The micellar properties of aqueous binary mixed solutions of sodium glycocholate, NaGC, and octa-oxyethylene glycol mono-n-decyl ether, C₁₀E₈, have been studied on the basis of surface tensions, the mean aggregation number and the polarity of the interior of the micelles. The mean aggregation number, measured by steady state quenching method, decreased with the increase of the mole fraction of NaGC in the mixed system. The polarity of the interior, estimated by the ratio of first and third vibronic peak in a monomeric pyrene fluorescence emission spectrum, suggested that the hydrophobicity of intramicelles increased with the increase of the mole fraction of NaGC in the mixed system. These are considered to be caused by the differences in the chemical structure and the hydrophobic nature between NaGC and C₁₀E₈. The mean aggregation number and the polarity of the interior for each micelle near the CMC in lower total concentration of surfactants showed the tendency approaching those of pure micelle of the nonionic surfactant. This suggests that the ratio of NaGC in the initial micelles in the range of lower total concentration near the CMC is lower than that of the corresponding prepared mole fraction in the mixed system. This lower value was confirmed also from theoretical calculation of the ratio of NaGC at the CMC in the mixed micelle by regular solution treatment of Rubingh in the solution.     

Craze fibril extension ratio measurements in glassy block copolymers

The extension ratios of crazes in triblock copolymer films of poly(2-vinylpyridine)-polystyrene-poly(2-vinylpyridine) [PVP-PS-PVP] which had lamellar microphase domain structure were measured by transmission electron microscopy. The extension ratio when the lamellae were oriented parallel to the craze fibril direction was always greater than that when the lamellae were oriented perpendicular to this direction, reflecting the stretching of the chains of the block copolymer in a direction normal to the interfaces of the lamellar domains.     

Synthesis and physical behavior of polyamide 6,10-poly(butadiene-co-acrylonitrile) segmented block copolymers

Segmented copolymers, characterized by polyamide 6,10 and poly(butadieneco-acrylonitrile) random blocks, were studied. Samples of such copolymers, having different relative content of the two components, were synthesized. Films were prepared by pressure molding and studied using differential scanning calorimetry and dynamicmechanical analysis. Results indicate that a phase segregation occurs and the system can be described by a matrix model. The matrix can be polyamidic or polybutadienic, depending on sample composition, while, in the matrix, the other component is organized in segregated domains.     

Azeotropic transformation in mixed monolayers of octadecylurea and hexadecylurea

The surface pressure of mixed monolayers of octadecylurea and hexadecylurea has been measured as a function of mean area per molecule at various temperatures and compositions. The surface pressure of the phase transition obtained was observed to decrease both with an increase in temperature and with an addition of another component. With the aid of the thermodynamic method developed previously, the apparent molar entropy and energy changes associated with the phase transition were found to be positive. These positive values were explained by the rupture of the intermolecular hydrogen bonding. Furthermore, the activity coefficients of film-forming components with reference to their respective pure components were considered in connection with the mutual interaction between octadecylurea and hexadecylurea molecules. It was concluded that the system exhibits the negative azeotropy as a result of the difficulty in forming the hydrogen bonding in the mixed monolayer.     

Miscibility of dodecyltrimethylammonium bromide and dodecyltrimethylammonium chloride in surface-adsorbed film and micelle

Surface tension of aqueous solutions of mixtures of dodecyltrimethylammonium bromide (DTAB) and dodecyltrimethylammonium chloride (DTAC) has been measured and analyzed by using thermodynamic relations. The adsorbed film has been found to contain more DTAB molecules than the solution. The shape formed by the curves of the total molality at constant surface tension against the solution and surface compositions indicates the ideal mixing of the DTAB and DTAC molecules in the adsorbed film. Micellar composition has been estimated at the critical micelle concentration (CMC). The micelles have been found to be richer in DTAB than the solution, but poorer in DTAB than the adsorbed film at the CMC. The DTAB and DTAC molecules have been shown to mix ideally in the micelles. From the comparison with the results on the system of decylammonium bromide and decylammonium chloride, it has been concluded that, on the mixing of surfactants differing only in counter ions, the adsorbed film is influenced more significantly by the ionic head group of the surfactant than the micelle.     

Crystallization of microphase-separated block copolymers with two crystallizing blocks

Statistical poly block copolymers of polyamide with polyethyleneoxide are investigated. The regularities governing the formation of their phase structure depending on the composition, temperature, and prehistory of the system are established. The character of crystallization of both blocks is shown to be due to their mutual solubility in the melt. Some peculiarities of microphase crystallization in PA/PEO block copolymers are revealed. It is found that, depending on the character of phase separation in the system, a PEO block may be crystallized either unimodally or in two well-separated temperature ranges.Dedicated to Prof. W. Pechhold on the occasion of his 60th birthday.