Improvement of the electrochemical properties of “as-grown” boron-doped polycrystalline diamond electrodes deposited on tungsten wires using ethanol

The electrochemical properties of boron-doped diamond (BDD) polycrystalline films grown on tungsten wire substrates using ethanol as a precursor are described. The results obtained show that the use of ethanol improves the electrochemistry properties of “as-grown” BDD, as it minimizes the graphitic phase upon the surface of BDD, during the growth process. The BDD electrodes were characterized by Raman spectroscopy, scanning electronic microscopy, cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS). The boron-doping levels of the films were estimated to be ∼10²⁰ B/cm³. The electrochemical behavior was evaluated using the and redox couples and dopamine. Apparent heterogeneous electro-transfer rate constants were determined for these redox systems using the CV and EIS techniques. values in the range of 0.01–0.1 cm s⁻¹ were observed for the and redox couples, while in the special case of dopamine, a lower value of 10⁻⁵ cm s⁻¹ was found. The obtained results showed that the use of CH₃CH₂OH (ethanol) as a carbon source constitutes a promising alternative for manufacturing BDD electrodes for electroanalytical applications.     

Palladized aluminum as a novel substrate for electrosynthesis of polyaniline in sulfuric acid solutions

The electropolymerization of aniline on a palladized aluminum electrode (Pd/Al) by potentiodynamic as well as potentiostatic methods is described. The effect of the monomer concentration between 0.01 and 0.4 M on the polyaniline (PANI) formation and its growth on the Pd/Al electrode was investigated and a suitable concentration of 0.2 M is suggested. A similar study was carried out to investigate the effect of sulfuric acid concentration and 0.1 M sulfuric acid was chosen. A study on the influence of electropalladization time on the polymer formation and its growth suggested a convenient time of 40 s. The stability of the PANI film on the Pd/Al electrode was studied as function of the potential imposed on the electrode. For applied electrode potentials of 0.1–0.7 V, the first-order degradation rate constant, k, of PANI film varies between 1×10⁻⁶ and 2×10⁻⁵ s⁻¹, and a relatively low slope (i.e., 2.2) was obtained for the plot of log k versus E. The coatings were characterized by scanning electron microscopy (SEM), and cyclic voltammetric behavior of the PANI-deposited Pd/Al electrode is discussed. The electrocatalytic activity of the PANI-deposited Pd/Al electrode against para-benzoquinone/hydroquinone (Q/H₂Q) and redox systems were investigated and on the basis of of the corresponding cyclic voltammograms and the redox systems were identified as the reversible and quasi-reversible systems, respectively.     

Mechanical properties of mixed conducting La0.5Sr0.5Fe1−x Co x O3−δ (0≤x≤1) materials

Young’s modulus, strain–stress behavior, fracture strength, and fracture toughness of (0≤×≤1) materials have been investigated in the temperature range 20–1,000°C. Young’s moduli of and , measured by resonant ultrasound spectroscopy, were 130±1 and 133±3 GPa, respectively. The nonlinear stress–strain relationship observed by four-point bending at room temperature was inferred as a signature of ferroelastic behavior of the materials. Above the ferroelastic to paraelastic transition temperature, the materials showed elastic behavior, but due to high-temperature creep, a nonelastic respond reappeared above ∼800°C. The room temperature fracture strength measured by four-point bending was in the range 107–128 MPa. The corresponding fracture toughness of , measured by single edge V-notch beam method, was 1.16±0.12 MPa·m^1/2. The measured fracture strength and fracture toughness were observed to increase with increasing temperature. The fracture mode changed from intragranular at low temperature to intergranular at high temperature. Tensile stress gradient at the surface of the materials caused by a frozen-in gradient in the oxygen content during cooling was proposed to explain the low ambient temperature fracture strength and toughness.     

Electrical and electro-chemical characterisation of La0.99Fe1−x Ni x O3−δ perovskites

(LFN, 0<x<0.6) perovskites were synthesised by a solid-state route and were characterised by powder XRD, dilatometry, four-point DC conductivity measurements and electro-chemical impedance spectroscopy (EIS) on cone-shaped electrodes using a Ce_1.9Gd_0.1O_1.95 (CGO10) electrolyte. All the compounds were of single phase, and they belong to either the cubic or the hexagonal crystal system. The thermal expansion coefficient (TEC) was in the range 10.7*10⁻⁶ K⁻¹ to 13.4*10⁻⁶ K⁻¹, which continued to increase with increasing nickel content. The highest electronic conductivity was measured for the composition giving a value of 670 S/cm at 380 °C. The highest electro-chemical performance was measured for the composition giving an area specific resistance as low as 5.5 Ωcm² at 600 °C based on EIS measurements on a cone-shaped electrode. Composite cathodes made from and CGO10 revealed a rather low performance due to an un-optimised micro-structure.

---

Mechanism of the catalyzed by cysteine electroreduction of the insoluble in water cobalt(II) salt as a component of carbon paste electrode

The mechanism of the Co(II) catalytic electroreduction of water insoluble CoR₂ salt in the presence of cysteine was developed. CoR₂ = cobalt(II) cyclohexylbutyrate is the component of a carbon paste electrode. Electrode surface consecutive reactions are: (a) fast (equilibrium) reaction of the complex formation, (b) rate-determining reversible reaction of the promoting process of CoR(Ac⁺) complex formation, (c) rate-determining irreversible reaction of the electroactive complex formation with ligand-induced adsorption, and (d) fast irreversible reaction of the electroreduction. Reactions (a,b) connected with CoR₂ dissolution and reactions (c,d) connected with CoR₂ electroreduction are catalyzed by . Regeneration of (reactions “b,d”) and accumulation of atomic Co(0) (reaction “d”) take place. Experimental data [Sugawara et al., Bioelectrochem Bioenergetics 26:469, 1991]: i _a vs E (i _a is anodic peak, E is cathodic accumulation potential), i _a vs , and i _a vs pH have been quantitatively explained.     

Kinetics of the uninhibited and ethanol-inhibited CoO,Co<Subscript>2</Subscript>O<Subscript>3</Subscript> and Ni<Subscript>2</Subscript>O<Subscript>3</Subscript> catalyzed autoxidation of sulfur(IV) in alkaline medium

For getting an insight into the mechanism of atmospheric autoxidation of sulfur(IV), the kinetics of this autoxidation reaction catalyzed by CoO, Co₂O₃ and Ni₂O₃ in buffered alkaline medium has been studied, and found to be defined by Eqs. I and II for catalysis by cobalt oxides and Ni₂O₃, respectively.

Oxygen stoichiometry,unit cell volume,and thermodynamic quantities of perovskite-type oxides

Perovskite-type oxides with A, A′=La, Ba, Sr; B, B′=Mn, Fe, Co were investigated by means of thermal analysis, solid electrolyte cells, and X-ray diffraction. Partial molar thermodynamic quantities are determined and their relations with O/M stoichiometry, unit cell volume, and phase stability were studied. The absolute values of partial molar enthalpies of perovskite-type oxides increase with increasing O/M stoichiometries and with decreasing unit cell volumes of the cubic perovskite-type structure, corresponding to higher chemical stabilities. The substitution of Ba for La, Ba for Sr, Co for Fe, and Fe for Mn lead to increase in unit cell volumes and decrease in absolute values of ΔH ⁰. The ΔH ⁰ values of the cobaltites/ferrites range from −33.5 kJ/mol for SrCo_0.8Fe_0.2O_3−x to −72.5 kJ/mol for La_0.2Sr_0.8Co_0.6Fe_0.4O_3−x, and of the manganates up to −132 kJ/mol for Ca_0.5Sr_0.5Mn_0.8Fe_0.2O_3−x .     

Mixed-conducting dense ceramic membranes for air separation and natural gas conversion

Non-perovskite SrFeCo_0.5O _x (SFC2) was found to have high electronic and ionic conductivities as well as structural stability. At 800°C in air, total and ionic conductivities of 17 and 7 S·cm⁻¹ were measured, respectively; the ionic transference number was calculated to be ≈0.4. This material is unique because of its high electronic conductivity and comparable electronic and ionic transference numbers. X-ray diffraction analysis showed that air-sintered SFC2 consists of three phase components, ≈75 wt% , ≈20 wt% perovskite , and ≈5 wt% rock salt CoO. Argon-annealed SFC2 contains brownmillerite Sr₂(Fe_1−x Co _x )₂O₅ and rock salt CoO. Dense SFC2 membranes were able to withstand large pO₂ gradients and retain mechanical strength. A 2.9-mm-thick disk membrane was tested in a gas-tight electrochemical cell at 900°C; an oxygen permeation flux rate ≈2.5 cm³(STP)·cm⁻²·min⁻¹ was measured. A dense thin-wall tubular membrane of 0.75-mm thickness was tested in a methane conversion reactor for over 1,000 h. At 950°C, the oxygen permeation flux rate was ≈10 cm³(STP)·cm⁻²·min⁻¹ when the SFC2 thin-wall membrane was exposed with one side to air and the other side to 80% methane balanced with inert gas. Results from these two independent experiments agreed well. The SFC2 material is a good candidate as dense ceramic membranes for oxygen separation from air or for use in methane conversion reactors.     

Electrochemical study of the thermodynamics and kinetics of hydrophilic ion transfers across water | <Emphasis Type="Italic">n</Emphasis>-octanol interface

Thermodynamics and kinetics of hydrophilic ion transfers across water|n-octanol (W|OCT) interface have been electrochemically studied by means of novel three-phase and thin-film electrodes. Three-phase electrodes used for thermodynamics measurements comprise edge plane pyrolytic graphite, the surface of which was partly modified with an ultrathin film of OCT, containing hydrophobic lutetium bis(tetra-tert-butylphthalocyaninato) (Lu[tBu₄Pc]₂) as a redox probe. The transfers of anions and cations from W to OCT were electrochemically driven by reversible redox transformations of Lu[tBu₄Pc]₂ to chemically stable lipophilic monovalent cation and anion , respectively. Upon reduction of Lu[tBu₄Pc]₂, the transfers of alkali metal cations from W to OCT have been studied for the first time, enabling estimation of their Gibbs transfer energies. For kinetic measurements, a thin-film electrode configuration has been used, consisting of the same electrode covered completely with a thin layer of OCT that contained the redox probe and a suitable electrolyte. Combining the fast and sensitive square-wave voltammetry with thin-film electrodes, the kinetics of , , and Cl⁻ transfers have been estimated. Dedicated to Professor Dr. Yakov I. Tur’yan on the occasion of his 85th birthday.     

Oxygen transport and thermomechanical properties of SrFe(Al)O3-δ –SrAl2O4 composites: microstructural effects

Measurements of oxygen permeation through dense composite membranes showed a considerable influence of processing conditions on the surface exchange kinetics, while the bulk ambipolar conductivity is almost unaffected by microstructural factors. Compared to the materials prepared via the glycine–nitrate process (GNP), the surface limitations to oxygen transport are significantly higher for dual-phase made of a commercial powder synthesized by spray pyrolysis. This difference in behavior may be related to compositional inhomogeneities in the grains of A-site deficient perovskite phase and an enhanced surface concentration of grain boundaries in the case of GNP-synthesized composite, which has also smaller grain size, slightly higher thermal expansion and lower total conductivity. No essential effects on Vickers hardness, varying in the range 6.3–6.5 GPa, were found. The deposition of porous catalyst layers onto the composite surface exposed to reducing environment leads to membrane decomposition. For the fabrication of tubular membranes, the cold isostatic pressing technique was, hence, combined with mechanical treatment to increase the specific surface area without incorporation of catalytically active components.     

Nonlinear magneto-optical effects and photomagnetism of electrochemically synthesized molecule-based magnets

This article describes novel optical functionalities such as photomagnetic effects and magnetization-induced second harmonic generation (MSHG) in several cyano-bridged metal assemblies. Single crystal- and film-types of a cyano-bridged Cu–Mo bimetallic assembly, , were electrochemically prepared. When this compound was irradiated with light, spontaneous magnetization with a Curie temperature (T _C) of 23 K was observed. Electrochemically prepared Fe^II[Cr^III(CN)₆]_2/3·5H₂O thin film, which was a ferromagnet with T _C=21 K, showed photoreduced magnetization. This photomagnetism is due to the change of ferromagnetic coupling between Fe^II and Cr^III. MSHG was observed in Cs^ICo^II[Cr^III(CN)₆]·0.5H₂O. This -type Prussian blue analog-based magnet is proven to be a piezoelectric ferromagnet, i.e., condensed matter with both piezoelectric and ferromagnetism. This MSHG is due to the coupling between a piezoelectric structure of and ferromagnetism with a T _C of 46 K.

Properties and performance of BaxSr1−xCo0.8Fe0.2O3−δ materials for oxygen transport membranes

The present paper discusses the oxygen transport properties, oxygen stoichiometry, phase stability, and chemical and mechanical stability of the perovskites (BSCF) and (SCF) for air separation applications. The low oxygen conductive brownmillerite phase in SCF is characterized using in-situ neutron diffraction, thermographic analysis and temperature programmed desorption but this phase is not present for BSCF under the conditions studied. Although both materials show oxygen fluxes well above 10 ml/cm²·min at T=1,273 K and pO₂=1 bar for self-supporting, 200 μm-thick membranes, BSCF is preferred as a membrane material due to its phase stability. However, BSCF’s long-term stable performance remains to be confirmed. The deviation from ideal oxygen stoichiometry for both materials is high: δ>0.6. The thermal expansion coefficients of BSCF and SCF are 24×10⁻⁶ and 30×10⁻⁶ K⁻¹, respectively, as determined from neutron diffraction data. The phenomenon of kinetic demixing has been observed at pO₂<10⁻⁵ bar, resulting in roughening of the surface and enrichment with alkaline earth metals. Stress–strain curves were determined and indicated creep behavior that induces undesired ductility at T=1,073 K for SCF. Remedies for mechanical and chemical instabilities are discussed.     

Effect of the mediator in feedback mode-based SECM interrogation of indium tin-oxide and boron-doped diamond electrodes

Indium tin-oxide (ITO) and polycrystalline boron-doped diamond (BDD) have been examined in detail using the scanning electrochemical microscopy technique in feedback mode. For the interrogation of electrodes made from these materials, the choice of mediator has been varied. Using ferrocene methanol (FcMeOH), and approach curve experiments have been performed, and for purposes of comparison, calculations of the apparent heterogeneous electron transfer rates (k _app) have been made using these data. In general, it would appear that values of k _app are affected mainly by the position of the mediator reversible potential relative to the relevant semiconductor band edge (associated with majority carriers). For both the ITO (n type) and BDD (p type) electrodes, charge transfer is impeded and values are very low when using FcMeOH and as mediators, and the use of results in the largest value of k _app. With ITO, the surface is chemically homogeneous and no variation is observed for any given mediator. Data is also presented where the potential of the ITO electrode is fixed using a ratio of the mediators and In stark contrast, the BDD electrode is quite the opposite and a range of k _app values are observed for all mediators depending on the position on the surface. Both electrode surfaces are very flat and very smooth, and hence, for BDD, variations in feedback current imply a variation in the electrochemical activity. A comparison of the feedback current where the substrate is biased and unbiased shows a surprising degree of proportionality.Dedicated to Alan, a good friend and colleague on his 60th birthday.     

Photoelectrode characteristics of an organic bilayer in water phase containing a redox molecule

We have recently reported that the organic bilayer of 3,4,9,10-perylenetetracarboxyl-bisbenzimidazole (PTCBI, n-type semiconductor) and 29H,31H-phthalocyanine (H₂Pc, p-type semiconductor), which is a part of a photovoltaic cell, acts as a photoanode in the water phase (Abe et al., ChemPhysChem 5:716, [2004]); in that case, the generation of the photocurrent involving an irreversible thiol oxidation at the H₂Pc/water interface took place to be coupled with hole conduction through the H₂Pc layer, based on the photophysical character of the bilayer. In the present work, the photoelectrode characteristics of the bilayer were investigated in the water phase containing a redox molecule , where the photo-induced oxidation and reduction for the couple were found to take place at the bilayer. The photoanodic current involving the oxidation efficiently occurred at the interface of H₂Pc/water, similar to the previous example. In the view of the voltammograms obtained, it was noted that there are pin-holes in the H₂Pc layer of the bilayer, leading to a cathodic reaction with at the PTCBI surface especially in the dark; that is, the band bending at the PTCBI/water interface can essentially be reduced by applying a negative potential [e.g., < ∼ 0 V (vs Ag/AgCl)] to the PTCBI, when the cathodic reaction may take place through the conduction band of the PTCBI. Moreover, under that applied potential condition of irradiation, the photogenerated electron carrier part can move to the PTCBI surface, thus enhancing the reduction of .     

Oxygen transport in La0.5Sr0.5Fe1−yTiyO3−δ (y=0.0, 0.2) membranes

The influence of partial substitution of Fe with Ti on the oxygen transport properties of La_1−x Sr _x FeO₃ membranes was investigated in view of their application for oxygen separation. Samples of composition (y=0, 0.2) were prepared and their oxygen transport properties characterised by potential step relaxation and by oxygen permeation measurement in an air/argon gradient. With the first technique, chemical diffusion and surface exchange (k _S) coefficients were obtained by fitting of the current relaxation data to a single expression valid over the complete time range. The Ti-substituted composition gave slightly larger values of and k _S. The trend was opposite for the measured oxygen permeation flux. In the latter experience, ordering of oxygen vacancies was observed at lower temperature, reducing significantly the performance of the material.     

On the charge storage mechanism at RuO<Subscript>2</Subscript>/0.5 M H<Subscript>2</Subscript>SO<Subscript>4</Subscript> interface

Comparative study of capacitative properties of RuO₂/0.5 M H₂SO₄ and Ru/0.5 M H₂SO₄ interfaces has been performed with a view to find out the nature of electrochemical processes involved in the charge storage mechanism of ruthenium (IV) oxide. The methods of cyclic voltammetry and scanning electron microscopy (SEM) were employed for the investigation of electrochemical behavior and surface morphology of RuO₂ electrodes. It has been suggested that supercapacitor behavior of RuO₂ phase in the potential E range between 0.4 and 1.4 V vs reference hydrogen electrode (RHE) should be attributed to double-layer-type capacitance, related to non-faradaic highly reversible process of ionic pair formation and annihilation at RuO₂/electrolyte interface as described by following summary equation:

Recent developments in Ruddlesden–Popper nickelate systems for solid oxide fuel cell cathodes

Motivated by recent work on the Ruddlesden–Popper material, which was shown to be a superior oxide-ion conductor than conventional solid-oxide fuel cell cathode perovskite materials, we undertook A- and B-site doping studies of the Ruddlesden–Popper nickelate series in an attempt to identify other candidates for cathode application. In this paper, we summarize our most significant results for the and systems and more recently, the higher-order Ruddlesden–Popper phases La _n+1Ni _n O_3n+1 (n=2 and 3), which show greater promise as cathode materials than the n=1 compositions.     

Kinetics of osmium(VIII) catalysis of periodate oxidation of DMF in aqueous alkaline medium

The osmium(VIII) catalysed IO₄ ⁻ oxidation of DMF in aqueous alkaline medium follows the rate law:

Precision of Raman depolarization and optical attenuation measurements of sound tooth enamel

The demineralization of enamel that is associated with early caries formation affects the optical properties of the enamel. Polarized Raman spectroscopy and optical coherence tomography have been used to detect these changes and potentially offer a means to detect and monitor early caries development. The total optical attenuation coefficient as measured by optical coherence tomography and the polarization anisotropy of the Raman peak arising from the symmetric ν₁ vibration of at approximately 959 cm⁻¹ have been demonstrated as being sensitive markers of early caries. This ex vivo study on extracted human teeth demonstrates that these measurements can be made with reasonable precision with concomitantly good repeatability and reproducibility in sound enamel. Such reliability is crucial for these techniques to have a practical clinical value.     

Oxygen permeation and stability of Zr0.8Y0.2O0.9‒La0.8Sr0.2CrO3-δ dual-phase composite

A tubular membrane made of Zr_0.8Y_0.2O_1.9 (60 vol%) and was prepared by a standard ceramic process. Oxygen permeation through the membrane tube was examined by exposing its outer shell to air and sweeping its inner wall with pure helium or CO balanced with helium. An oxygen flux of 9.2×10⁻⁹ mol cm⁻² s⁻¹ was measured at 950°C under air/He gradient, and a larger flux of 3.2×10⁻⁸ mol cm⁻² s⁻¹ at 930°C under air/CO gradient. The membrane tube was found to exhibit excellent stability under highly reducing atmosphere and elevated temperatures. The oxygen permeation rate is likely to be increased through the modification of the surface and reduction of the membrane thickness.