Liquid crystal alignment properties on surface-reformed solution-derived lanthanum-doped zinc oxide films

Liquid crystal (LC) alignment characteristics were investigated using a solution-derived lanthanum-doped zinc oxide (La:ZnO) film that was exposed to various intensities of ion-beam (IB) irradiation. At an IB intensity of 1700 eV, uniform and homogeneous LC alignment was achieved, as revealed by cross-polarized optical microscopy and pre-tilt angle measurement. Field-emission scanning electron microscopy (FE-SEM), atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS) were used to verify that the IB irradiation induced physical and chemical surface reformation of the La:ZnO film that relate to LC alignment. FE-SEM and AFM revealed that the IB irradiation reformed the existing surface structure into a new structure with an altered surface roughness. The XPS results showed that the van der Waals force with anchoring energy increased as the IB intensity increased, and this profoundly affected the state of LC alignment. The capacitance-voltage (C-V) hysteresis curve was measured as a function of IB intensity to characterize the accumulated charge as a residual DC. Nearly zero C-V hysteresis was achieved at an IB intensity of 1700 eV. Therefore, a solution-derived La:ZnO film with an IB intensity of 1700 eV has great potential for high-quality LC applications.     

Photo-induced Janus effect of graphene oxide films

The effect of UV irradiation on the wettability of GO films, as well as the possibility of making a film with different properties of its surface, the Janus film, has been studied. The O/C ratio changes from 0.32 to 0.26 after 6 ​h of UV irradiation. The contact angle of water droplet wetting on an unirradiated surface is θ ​≈ ​35°. The contact angle reaches more than 95° on the irradiated surface, which means that a hydrophobic surface on a film can be obtained. The origin of amphiphilic properties of the GO film are associated with the photochemical reduction of GO.     

Enhanced super-hydrophobic and switching behavior of ZnO nanostructured surfaces prepared by simple solution--immersion successive ionic layer adsorption and reaction process

A simple and cost-effective successive ionic layer adsorption and reaction (SILAR) method was adopted to fabricate hydrophobic ZnO nanostructured surfaces on transparent indium-tin oxide (ITO), glass and polyethylene terephthalate (PET) substrates. ZnO films deposited on different substrates show hierarchical structures like spindle, flower and spherical shape with diameters ranging from 30 to 300 nm. The photo-induced switching behaviors of ZnO film surfaces between hydrophobic and hydrophilic states were examined by water contact angle and X-ray photoelectron spectroscopy (XPS) analysis. ZnO nanostructured films had contact angles of ~140° and 160°±2 on glass and PET substrates, respectively, exhibiting hydrophobic behavior without any surface modification or treatment. Upon exposure to ultraviolet (UV) illumination, the films showed hydrophilic behavior (contact angle: 15°±2), which upon low thermal stimuli revert back to its original hydrophobic nature. Such reversible and repeatable switching behaviors were observed upon cyclical exposure to ultraviolet radiation. These biomimetic ZnO surfaces exhibit good anti-reflective properties with lower reflectance of 9% for PET substrates. Thus, the present work is significant in terms of its potential application in switching devices, solar coatings and self-cleaning smart windows.     

Preparation of superhydrophobic composite paper mulching film

To study the influence of different concentrations of zinc oxide (ZnO)/silicon dioxide (SiO₂) composite coating on hydrophobic property and mechanical stability of paper mulch film, three kinds of ZnO/SiO₂ composite coating paper mulch films (2%, 4%, 6%) with different coating substance contents were prepared by brush coating method. Through particle size analysis, contact angle, rolling angle and mechanical stability test, combined with scanning electron microscope, three-dimensional morphology and roughness measuring instrument, the optimal concentration of ZnO/SiO₂ composite coated paper mulch film was screened out. Through acid-base salt corrosion test, silver mirror reaction and surface self-cleaning, the optimal concentration of composite coated paper mulch film was compared with the original paper mulch film to prove its excellent chemical stability and hydrophobicity. The results show that the paper mulch film with 4% coating material has excellent hydrophobicity and mechanical stability, can effectively reduce the surface roughness of paper mulch film, and has remarkable effects in resisting acid, alkali and salt and self-cleaning.     

嵌入花生酸镉单层中的卟啉-紫精分子聚集行为的研究

本文制备了卟啉-紫精与花生酸镉混合LB膜, 用紫外可见光谱研究了膜中卟啉基团的聚集及取向, X射线衍射说明混合LB膜具有层状有序的周期结构。扫描电镜结果表明: 通过调节膜的表面压可使聚集成"微畴"的卟啉-紫精均匀分布在花生酸镉单分子层中, 随膜表面压的增大, 小的"微畴"相互连接形成更大的"微畴"。电子衍射说明混合膜中两组份分相存在, 且都为六角对称的有序结构。     

Bio-inspired fabrication of well-oriented ZnO nanorod arrays film and its superhydrophobicity and superhydrophilicity

A highly oriented ZnO nanorod array film was fabricated on glass substrate by combinations of Sol–Gel and hydrothermal. The film exhibits perfect superhydrophobicity with a contact angle of 155° and a glide angle of 4° after being surface modified by fluoroalkylsilane, which is similar with wings’ property and structures of large yellow spots mosquitoes. Interestingly, the ZnO nanorods film were converted from superhydrophobicity into superhydrophilicity under ultraviolet light for 2 h due to the decomposition of fluoroalkyl chain of fluoroalkylsilane and the photosensitivity of ZnO surface. The transition mechanisms of wettability are discussed on the basis of correlated theories.     

微结构与表面修饰对二氧化硅多孔薄膜疏水性能的影响

通过引入聚乙二醇(PEG)改性传统二氧化硅(SiO2)溶胶,得到了粒径分布较宽且粒径可控的溶胶。比较了六甲基二硅氮烷(HMDS)溶胶内修饰和薄膜表面修饰以及溶胶粒径对SiO2薄膜疏水性能的影响。采用动态光散射粒度仪定量测试了二氧化硅溶胶老化过程中粒度的变化,用原子力显微镜、接触角测试仪、红外光谱仪、紫外-可见-近红外分光光度计分别对薄膜的表面形貌、表观静态接触角、薄膜成分及透光率等进行了测量。结果表明:PEG的添加可有效增大溶胶粒度从而增大薄膜的粗糙度,提高薄膜的疏水性。表面修饰效果受修饰方式和SiO2粒径影响,粒径较小时有利于溶胶内修饰,粒径较大时有利于对薄膜修饰。经过表面修饰剂(HMDS)的气氛处理得到了接触角为152°的超疏水薄膜,而且相比溶胶内修饰可以减小薄膜透光率的损失。     

Physicochemical analysis of ion beam-induced surface modifications on polyethylene glycol films for liquid crystal alignment

ABSTRACT

We investigated the surface modification induced by the ion-beam (IB) irradiation of a polyethylene glycol (PEG) film and its liquid crystal (LC) alignment characteristics. The X-ray photoelectron spectroscopy analysis revealed the chemical modification; as the IB incidence angle increased, the number of surface C–O bonds decreased, inducing an anisotropic dipole moment on the PEG film surface. In addition, the physical modification was demonstrated via atomic force microscopy analysis using three-dimensional images as a function of the IB incidence angle. The surface roughness was analyzed; the modification with the smoothest surface was observed for an IB incidence angle of 45°. This modification affected the LC alignment state of the PEG film, as demonstrated by the polarized optical microscopy analysis with pre-tilt angle measurements. Furthermore, for the same IB incidence angle, the residual DC measured using the capacitance–voltage curves was extremely low. Hence, a PEG film irradiated with an IB incidence angle of 45° could be a suitable LC alignment layer.     

Surface-interface investigations of an ultrathin pulsed laser deposited NiO/ZnO bilayer structure

We hereby report detailed structural and morphological studies for an ultrathin NiO/ZnO bilayer structure grown on sapphire (001) substrate using pulsed laser deposition technique. The combined X-ray reflectivity (XRR) and grazing incidence X-ray fluorescence (GIXRF) studies revealed formation of a low-density defective ZnO interfacial layer of thickness ~32 Å at the ZnO/sapphire interface prior to growth of main ZnO layer. Our results further indicate that the variation of electron density across the NiO/ZnO bilayer structure is smooth and we do not observe presence of any interface layer between them. X-ray diffraction measurements show that deposited ZnO layer is epitaxial in nature whereas NiO is highly oriented along (100) direction. The angle dependent X-ray absorption near edge fine structure (XANES) measurements at Ni–K edge has been utilized to determine depth-resolved oxidation state of Ni and the results have been correlated with the depth-resolved electron density of NiO layer. The method described here offers nondestructive determination of the microstructural parameters as well as depth-resolved mapping of oxidation state of a thin film-based heterojunction device. It extends several advantages over destructive methods which are abundantly reported in literature.     

Patterning of cells on a PVC film surface functionalized by ion irradiation

Micropatterns of cells on a poly(vinyl chloride) (PVC) film surface were created by using ion irradiation. A PVC film was irradiated with H⁺ ions through a pattern mask in order to create patterns of the hydrophilic/hydrophobic regions on the PVC surface. The effect of ion irradiation on the surface properties of the PVC film was characterized by using Fourier transform‐infrared spectroscopy (FT‐IR), water contact angle measurement, and X‐ray photoelectron spectroscopy (XPS). The results revealed that the chemical environment of the PVC film surface was effectively changed by ion irradiation due to dehydrochlorination and oxidation. The in vitro cell culture on the patterned PVC film surface showed selective adhesion and proliferation of the cells on the ion‐irradiated regions. Well‐defined 50 µm patterns of the cells were obtained on the PVC film surface irradiated to 1 × 10¹⁵ ions/cm². Copyright © 2009 John Wiley & Sons, Ltd.     

An investigation of Zn/ZnO:Al/p-Si/Al heterojunction diode by sol–gel spin coating technique

Present study shows the structural, morphological, optical characterization of sol–gel spin coated ZnO:Al film and investigation of device efficiency of Zn/ZnO:Al/p-Si/Al heterojunction diode structure. X-ray diffraction study indicates that film has hexagonal polycrystalline structure with (002) preferential direction. Atomic force microscope and scanning electron microscope images exhibit that surface of ZnO:Al/p-Si consists of homogenously scattered nanoparticles. The surface roughness of ZnO:Al film is found to be 15.24 nm. The band gap value of ZnO:Al film deposited on glass substrate is calculated to be 3.34 eV. The electrical characterization of Zn/ZnO:Al/p-Si/Al heterojunction structure is made by current–voltage (I–V) and capacitance–voltage (C–V) measurements. From these measurements, the heterojunction structure shows a rectifying behavior under a dark condition. The ideality factor and barrier height of Zn/n-ZnO:Al/p-Si/Al structure are calculated as 3.23 and 0.68 eV. The heterojunction structure have diode characteristic with rectification ratio at 64.4 at +2.0 V in the dark. The results suggest that Zn/ZnO:Al/p-Si/Al heterojunction diode can be successfully used in many optoelectronic applications.     

含氟硅丙烯酸酯乳液超疏水膜中疏水基团的梯度分布与表面微观结构研究

利用含氟疏水基团的梯度分布,结合草莓形纳米SiO2粒子提供的双重粗糙表面,制备了具有类"荷叶效应"的超疏水涂膜,水接触角达(174.2±2)°,滞后角几乎接近0°.通过原子力显微镜、扫描电镜和水接触角的测试对膜表面形貌及疏水性能进行了表征;探讨了其表面微观结构与表面疏水性能的关系.草莓形复合粒子在膜表面的无规则排列赋予涂膜表面不同等级的粗糙度,使水滴与涂膜表面接触时能够形成高的空气捕捉率,这种微观结构与疏水基团的梯度分布相结合,赋予了含氟硅丙烯酸酯乳液涂膜表面超疏水性能.     

Biaxially Oriented Polypropylene (BOPP) Surface Modification by Nitrogen Atmospheric Pressure Glow Discharge (APGD) and by Air Corona

We compare two surface treatments of biaxially-oriented polypropylene (BOPP), which are carried out in the same dielectric barrier discharge (DBD) apparatus, namely air corona, and N₂ atmospheric pressure glow discharge (APGD). Changes in the surface energy and chemistry are investigated by contact angle measurements, by X-ray photoelectron spectroscopy (XPS) and by attenuated total reflectance infrared spectroscopy (ATR-FTIR). It is shown that N₂ APGD treatment leads to a higher surface energy than air corona treatment, and to the formation of mostly amine, amide, and hydroxyl functional groups at the polypropylene surface. Finally, hydrophobic recovery of the treated film is studied; for both treatment types, the increased surface energy is found to decay in a similar manner with increasing storage time after treatment.     

Piezoelectricity of ZnO Films Prepared by Sol-Gel Method

"ZnO piezoelectric thin films were prepared on crystal substrate Si(111) by sol-gel technology, then characterized by scanning electron microscopy, X-ray diffraction and atomic force microscopy (AFM). The ZnO films characterized by X-ray diffraction are highly oriented in (002) direction with the growing of the film thickness. The morphologies, roughness and grain size of ZnO film investigated by AFM show that roughness and grain size of ZnO piezoelectric films decrease with the increase of the film thickness. The roughness dimension is 2.188-0.914 nm. The piezoelectric coeocient d33 was investigated with a piezo-response force microscope (PFM). The results show that the piezoelectric coeocient increases with the increase of thickness and (002) orientation. When the force reference is close to surface roughness of the films, the piezoelectric coefficient measured is inaccurate and fluctuates in a large range, but when the force reference is big, the piezoelectric coeocient d33 changes little and ultimately keeps constant at a low frequency."     

Liquid crystal aligning capabilities on surface-reformed indium-doped zinc oxide films via ion-beam exposure

We investigated the characteristics of a solution-processed indium-doped zinc oxide (In:ZnO) film formed via ion-beam (IB) irradiation as a liquid crystal (LC) alignment layer. The In:ZnO film was deposited using solution processing and cured at various temperatures. Uniform LC alignment was observed at all curing temperatures in cross-polarised optical microscopy images. A regular pre-tilt angle supported these results and showed homogeneous LC alignment. Several surface analyses were conducted to evaluate the effect of IB irradiation on the In:ZnO film surface. X-ray diffraction analysis showed an amorphous structure both before and after IB irradiation, and physical surface reformation was observed using atomic force microscopy. Root mean square surface roughness was reduced and a smooth surface was achieved after IB irradiation. X-ray photoelectron spectroscopy was used to detect chemical surface reformation. It was found that the IB irradiation broke the metal-oxide bonds and increased the occurrence of oxygen vacancies, which affected the van der Waals forces between the LC molecules and the In:ZnO film surface. Electrical performance was observed to identify the possibility of using the In:ZnO film in LC applications. Enhanced electro-optical performance was measured and zero residual DC voltage which was verified using a capacitance-voltage curve was achieved.     

Silver Nanoparticle Thin Films with Nanocavities for Surface‐Enhanced Raman Scattering

The formation of nanometer‐sized gaps between silver nanoparticles is critically important for optimal enhancement in surface‐enhanced Raman scattering (SERS). A simple approach is developed to generate nanometer‐sized cavities in a silver nanoparticle thin film for use as a SERS substrate with extremely high enhancement. In this method, a submicroliter volume of concentrated silver colloidal suspension stabilized with cetyltrimethylammonium bromide (CTAB) is spotted on hydrophobic glass surfaces prepared by the exposure of the glass to dichloromethysilane vapors. The use of a hydrophobic surface helps the formation of a more uniform silver nanoparticle thin film, and CTAB acts as a molecular spacer to keep the silver nanoparticles at a distance. A series of CTAB concentrations is investigated to optimize the interparticle distance and aggregation status. The silver nanoparticle thin films prepared on regular and hydrophobic surfaces are compared. Rhodamine 6G is used as a probe to characterize the thin films as SERS substrates. SERS enhancement without the contribution of the resonance of the thin film prepared on the hydrophobic surface is calculated as 2×10⁷ for rhodamine 6G, which is about one order of magnitude greater than that of the silver nanoparticle aggregates prepared with CTAB on regular glass surfaces and two orders of magnitude greater than that of the silver nanoparticle aggregates prepared without CTAB on regular glass surfaces. A hydrophobic surface and the presence of CTAB have an increased effect on the charge‐transfer component of the SERS enhancement mechanism. The limit of detection for rhodamine 6G is estimated as 1.0×10^?8 M . Scanning electron microscopy and atomic force microscopy are used for the characterization of the prepared substrate.     

Preparation and characterization of nanocomposite ZnO–Ag thin film containing nano-sized Ag particles: influence of preheating,annealing temperature and silver content on characteristics

Nanocomposite ZnO–Ag thin film containing nano-sized Ag particles have been grown on glass substrate by spin-coating technique using zinc acetate dihydrate as starting precursor in 2-propanol as solvent and monoethanolamine as stabilizer. Silver nanoparticles were added in the ZnO sol using silver nitrate dissolved in ethanol-acetonitrile. Their structural, electrical, crystalline size and optical properties were investigated as a function of preheating, annealing temperature and silver content. The results indicated that the crystalline phase was increased with increase of annealing temperature up to 550 °C at optimum preheating temperature of 275 °C. Thermal gravimetric differential thermal analysis results indicated that the decomposition of pure ZnO and nanocomposite ZnO–Ag precursors occurred at 225 and 234 °C, respectively with formation of ZnO wurtzite crystals. The scanning electron microscopy and atomic force microscopy revealed that the surface structure (the porosity and grain size) of the ZnO–Ag thin film (the film thickness is about 379 nm) was changed compared to pure ZnO thin film. The result of transmission electron microscopy showed that Ag particles were about 5 nm and ZnO particles 58 nm with uniform silver nanoclusters. Optical absorption results indicated that optical absorption of ZnO–Ag thin films decreased with increase of annealing temperature. Nanocomposite ZnO–Ag thin films with [Ag] = 0.068 M and [Ag] = 0.110 M showed an intense absorption band, whose maximum signals appear at 430 nm which is not present in pure ZnO thin films. The result of X-ray photoelectron spectroscopy revealed that the binding energy of Ag 3d_5/2 for ZnO–Ag shifts remarkably to the lower binding energy compared to the pure metallic Ag due to the interaction between Ag and ZnO.     

Study of hydrophilicity and stability of chemically modified PDMS surface using piranha and KOH solution

Successful realization of various BioMEMS devices demands effective surface modification techniques of PDMS elastomer. This paper presents a detailed report on a simple and cost effective approach for surface modification of PDMS films involving wet chemical treatment in two‐step processes: primarily involving piranha solution followed by KOH dip to improve hydrophilicity and stability of PDMS surface. Chemical composition of the solution and surface treatment condition have been varied and optimized to significantly increase the surface energy. The effect of surface modification of the elastomer after wet chemical treatment is analyzed using contact angle measurement and FTIR‐ATR study. PDMS surface treated in piranha solution with H₂O₂ and H₂SO₄ in the ratio of 2:3 followed by a dip in KOH solution for 15 min duration each, demonstrated a maximum reduction of contact angle to ～27° as compared to untreated sample having a contact angle of ～110°. The removal of hydrophobic methyl group from elastomer surface and subsequent hydrophilization of surface by wet chemical process was confirmed from FTIR‐ATR spectra. This result is also supported by improved adhesion and electrical continuity of deposited aluminum metal film over the modified PDMS surface. Copyright © 2011 John Wiley & Sons, Ltd.     

The effects of oxygen concentration on ultraviolet luminescence of ZnO films by sol–gel technology and annealing

ZnO thin films were successfully deposited on SiO₂/Si substrate using the sol–gel technique and annealed in various annealing atmospheres at 900 °C by rapid thermal annealing (RTA). X-ray diffraction revealed the (002) texture of ZnO thin films. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) showed that the grains of the ZnO thin film were enlarged and its surface was smoothed upon annealing in oxygen. PL measurement revealed two ultraviolet (UV) luminescence bands at 375 and 380 nm. The intensity of the emission peak at 380 nm became stronger as the concentration of oxygen in the annealing atmosphere increased. The X-ray photoelectron spectrum (XPS) demonstrated that a more stoichiometric ZnO thin film was obtained upon annealing in oxygen and more excitons were generated from the radiative recombination carriers consistently. Additionally, the UV intensity increased with the thickness of ZnO thin film.     

Fabrication of Large‐Scale Hierarchical ZnO Hollow Spheroids for Hydrophobicity and Photocatalysis

We report here the preparation of a crystalline, pure hexagonal phase of ZnO as hollow 500–800 nm spheroids in the presence of organic bases, such as pyridine, using zinc acetate as the precursor salt. The spheroids exhibit unique 3D hierarchical architectures, like cocoons, and demonstrate improved superhydrophobic (water contact angle, 150°) character due to the inherited air‐trapped capillarity within the cocoon structure. The simple synthetic strategy used in this process is modified hydrothermolysis (MHT), which represents a general approach and may contribute to the formation mechanism of the hollow nanostructures with highly improved porosity. Depending on the concentration of the precursor salt, it has been possible to cover glass plates or the inner wall of a reaction vessel with ZnO nanocrystals. A low salt concentration (<0.01 M ) allows the easy preparation of a superhydrophobic glass surface, whereas a high salt concentration (>0.01 M ) results in the precipitation of cocoons at the bottom of the reaction vessel as a solid mass together with a deposited thin film of ZnO nanocrystals covering the inner wall of the glass vessel. The thickness of the film successively grows through repetitive hydrothermolysis processes for which a low salt concentration (<0.01 M ) was employed. Because of the hollow cocoonlike morphology, the surface area of the film is greatly increased, which makes it accessible for functionalization by incoming substrates from both sides (internally and externally) and helps to drive a competent photocatalytic dye degradation pathway. The heterocyclic base pyridine exclusively develops cocoons. Thus, the mechanism of self‐aggregation of ZnO nanocrystals under MHT reaction conditions has been studied and the characterization of the compounds has been supported with physical measurements.