Structure-relationships in electrocatalysis: oxygen reduction and hydrogen oxidation reactions on Pt(111) and Pt(100) in solutions containing chloride ions

Kinetics of the oxygen reduction reaction (orr) and the hydrogen evolution–oxidation reactions (her/hor) were studied on the Pt(111) and Pt(100) surfaces in 0.05 M H₂SO₄ containing Cl⁻. The orr is strongly inhibited on the (100) surface modified by adsorbed Cl⁻ (Cl_ad), and it occurs as a 3.5e⁻ reduction via solution phase peroxide formation. In the hydrogen adsorption (H_upd) potential region, the orr is even more inhibited, and corresponds only to a 2 e⁻ reduction at the negative potential limit where the electrode is covered by one monolayer of H_upd and some (unknown) amount of Cl_ad. On the Pt(111)---Cl_ad surface, the orr is inhibited relatively little (in addition to that caused by strong bisulfate anion adsorption on this surface), and the reaction pathway is the same as in Cl⁻ free solution. The kinetics of the hor on Pt(111) are the same in pure solution and in a solution containing Cl⁻, since Cl_ad does not affect platinum sites required for the breaking of the H---H bond. A relatively large inhibition of the hor is observed on the (100) surface, implying that strongly adsorbed Cl_ad is present on the surface even near 0 V.     

Catalytic effects of metal submonolayers formed by faradaic adsorption on the anodic oxidation of ascorbic acid at a platinum electrode

The catalytic effects of metal ions on the anodic oxidation of ascorbic acid on a Pt electrode in 1 M HClO₄ were studied by linear sweep voltammetry. The anodic peak due to a two-electron oxidation of ascorbic acid shifts to the negative potential side on the addition of Bi³⁺. This indicates the accelerating effect of Bi³⁺ on the oxidation of ascorbic acid. The presence of other metal ions, such as Pb²⁺, Hg²⁺, Tl⁺, Ag⁺ and Sb³⁺, also exerts similar effects. These metal ions were adsorbed on a Pt electrode at underpotentials and the adsorbed metals (denoted as M_ad) still remain on the electrode surface until the electrode potential goes up to and beyond the peak potential of the oxidation of ascorbic acid. On the other hand, metal ions forming no adsorbed layer on Pt, such as Co²⁺, Zn²⁺, Fe³⁺ and Ni²⁺, exhibit no catalytic effect. These facts suggest that the presence of a M_ad on Pt is essential for the promotion of the anodic oxidation of ascorbic acid. However, there is a difference in the catalytic action among the M_ad, for example, Cu_ad, Cd_ad, In_ad, Sn_ad and Mo_ad display no catalytic action.The catalytic activity depends on the degree of surface coverage by the M_ad. The maximal effect of the M_ad is attained in the submonolayer region. The effects of metal ions were discussed on the basis that the M_ad plays its major role in the removal of the adsorbed ascorbic acid occupying active sites on the electrode surface, and provides effective sites for the activation of adjacent water molecules. Furthermore, from the ¹³C NMR spectra for the oxidation products, the adsorbed water on the M_ad appears to function by promoting the subsequent hydration steps, following the electron-transfer step of ascorbic acid.     

Synthesis and Photocatalytic Activity of Poly(triazine imide)

Poly(triazine imide) was synthesized with incorporation of Li⁺ and Cl^? ions (PTI/Li⁺Cl^?) to form a carbon nitride derivative. The synthesis of this material by the temperature‐induced condensation of dicyandiamide was examined both in a eutectic mixture of LiCl–KCl and without KCl. On the basis of X‐ray diffraction measurements of the synthesized materials, we suggest that a stoichiometric amount of LiCl is necessary to obtain the PTI/Li⁺Cl^? phase without requiring the presence of KCl at 873 K. PTI/Li⁺Cl^? with modification by either Pt or CoO_x as cocatalyst photocatalytically produced H₂ or O₂, respectively, from water. The production of H₂ or O₂ from water indicates that the valence and conduction bands of PTI/Li⁺Cl^? were properly located to achieve overall water splitting. The treatment of PTI/Li⁺Cl^? with [Pt(NH₃)₄]²⁺ cations enabled the deposition of Pt through ion exchange, demonstrating photocatalytic activity for H₂ evolution, while treatment with [PtCl₆]^2? anions resulted in no Pt deposition. This was most likely because of the preferential exchange between Li⁺ ions and [Pt(NH₃)₄]²⁺ cations.     

522—Catalytic oxydation of biological components on platinum electrodes modified by adsorbed metals: Anodic oxidation of glucose

The catalytic oxidation of glucose on Pt electrodes modified by adsorbed metals was studied in 1 M HClO₄ by linear sweep voltammetry. The adsorbed metals (denoted as M_ad, such as Bi_ad and Pb_ad) formed on Pt in the potential region more positive than the reversible potential of an M⁼⁺/M^o couple, lead to a marked increase in the anodic c?urrent of glucose by about one order of magnitude. The catalytic activity depends on the surface coverage by the M_ad. The strongly adsorbed species of lactone type, which are responsible for blocking the successive oxidation, are formed on the electrode surface in the anodic processes of glucose on a bare Pt electrode. The formation of such poisonous species is accelerated in the presence of adsorbed hydrogen on Pt. The effects of M_ad were discussed on the basis that M_ad plays its major role on the Pt electrode surface in removal of the adsorbed hydrogen which initiates the formation of the poisonous species.     

Reactivity of the Pt/WO3/GC Electrode Towards Ethylene Glycol Oxidation in 0.1 M H2SO4

WO₃ has been prepared via thermal decomposition of ammonium paratungstate. The obtained oxide has been characterized by X‐ray diffraction (XRD) spectroscopy. The particle size was found to increase with increasing calcination temperature. The modified Pt/WO₃/GC electrode has been prepared and characterized using various analytical and electrochemical techniques. The electrochemical oxidation of ethylene glycol (EG) on the modified electrode was investigated and compared with that of a Pt/GC electrode in acidic solution. The presence of WO₃ enhanced the electrode activity towards EG oxidation. The enhancement factor was found to depend on the ratio of WO₃:Pt as well as on the calcination temperature during WO₃ preparation     

Enhanced Electrocatalytic Activity of Dual Template Based Pt/Cu‐zeolite A/Graphene for Methanol Electrooxidation

A novel Pt/Cu‐zeolite A/graphene based electrocatalyst was successfully prepared by chemical reduction method for methanol electrooxidation. Graphite oxide and Cu functionalized zeolite A were simultaneously reduced by NaBH₄ to prepare Cu‐zeolite A/graphene support which was used to deposit Pt nanoparticles. The nanostructure and composition of as‐prepared Pt/Cu‐zeolite A/graphene composites were characterized by X‐ray diffractometer, X‐ray fluorescence, Fourier transform infrared spectrometer and scanning electron microscopy. The electrocatalytic properties of Pt/Cu‐zeolite A/graphene modified electrode for methanol oxidation were investigated by cyclic voltammetry and chronoamperometry in 0.10 mol/L H₂SO₄ + 0.50 mol/L CH₃OH solution. Compared with Pt/zeolite A/graphene electrode and Pt/graphene electrode, Pt/Cu‐zeolite A/graphene based electrode exhibited obviously enhanced current and higher electrocatalytic activity for methanol electrooxidation. The increased electrocatalytic activity was attributed to the presence of zeolite A and reduced graphene oxide based dual template, which significantly increased the effective electrode surface and facilitated the diffusion of analytes into the electroactive catalyst.     

5,5′‐Hydrazinebistetrazole: An Oxidation‐stable Nitrogen‐rich Compound and Starting Material for the Synthesis of 5,5′‐Azobistetrazolates

All 5,5′‐hydrazinebistetrazoles reported in the literature are sensitive to oxidation and react with atmospheric oxygen to yield the corresponding 5,5′‐azobistetrazolates on time. Herewith, we report on the synthesis of the free acid 5,5′‐hydrazinebistetrazole (HBT) which showed to be stable on air for extended periods of time. The compound was fully characterized by analytical and spectroscopic methods and its X‐ray structure was determined by diffraction techniques. Besides, we determined its explosive properties by BAM methods and calculated its heat of formation (+414 kJ mol^?1), detonation velocity (8523 m s^?1) and detonation pressure (27.7 GPa). HBT proved to be very safe to handle (impact sensitivity: >30 J, friction sensitivity: ～108 N) and was used as a starting material for the synthesis of some already reported 5,5′‐azobistetrazolates: NH₄⁺, NH₂NH₃⁺, Li⁺, Na⁺, K⁺, Rb⁺, Cs⁺, Mg²⁺, Ca²⁺, Sr²⁺ and Ba²⁺.     

Exploring the Anion–Cation Interaction in m‐Terphenyltetrafluorosilicates by Using Multinuclear NMR Spectroscopy,X‐ray Diffraction,and ICR‐FT‐MS

The synthesis of a series of m‐terphenyl‐substituted tetrafluorosilicates with different cations (Na⁺, K⁺, Rb⁺, Cs⁺, Ag⁺, Tl⁺) is described and the interactions between the anion and cation are investigated in the solid, solution, and gas states by using multinuclear NMR spectroscopy, X‐ray diffraction, and ion cyclotron resonance Fourier‐transform mass spectrometry (ICR‐FT‐MS). In solution, heteronuclear NMR spectroscopy parameters show only limited sensitivity to the nature of the cation, which furthermore can be affected by solvent effects. More pronounced effects are observed in the structural data obtained from X‐ray diffraction studies, which are in good agreement with experimental gas‐phase data from ESIMS. ESIMS also reveals the existence of dimeric species of the type [M(DmpSiF₄)₂]^? (Dmp=2,6‐dimesitylphenyl), the stability of which was determined by normalized collision energy experiments.     

Zundel‐like and Eigen‐like Hydrated Protons on a Platinum Surface

The nature of hydrated protons is an important topic in the fundamental study of electrode processes in acidic environment. For example, it is not yet clear whether hydrated protons are formed in the solution or on the electrode surface in the hydrogen evolution reaction on a Pt electrode. Using mass spectrometry and infrared spectroscopy, we show that hydrogen atoms are converted into hydrated protons directly on a Pt(111) surface coadsorbed with hydrogen and water in ultrahigh vacuum. The hydrated protons are preferentially stabilized as multiply hydrated species (H₅O₂⁺ and H₇O₃⁺) rather than as hydronium (H₃O⁺) ions. These surface‐bound hydrated protons may play an important role in the interconversion between adsorbed hydrogen atoms and solvated protons in solution.     

Nanocomposite of Platinum Particles Embedded into Nanosheets of Polycarbazole for Methanol Oxidation

Nanoparticles of Pt were successfully electrodeposited onto polycarbazole (PCz) film on a stainless steel (SS‐PCz‐Pt) by chronocoulometry (0.2 C). For comparative purposes, Pt particles were deposited into stainless steel (SS‐Pt) under the same condition. Fourier transform infrared spectroscopy (FT‐IR) results confirmed PCz exists in the SS‐PCz‐Pt composite electrode. X‐ray photoelectron spectroscopy (XPS) results indicated that PCz of SS‐PCz can interact easily with Pt particles. The crystalline behavior and morphology of SS‐PCz‐Pt and SS‐Pt were determined by X‐ray diffraction (XRD) analysis, scanning electron microscopy (SEM), and Transmission Electron Microscopy (TEM). The TEM results indicated that Pt particles disperse more uniformly into the nanosheets of polycarbazole than those of SS film. Catalytic activity and stability for the oxidation of methanol were studied by using cyclic voltammetry and chronoamperometry. A high catalytic current for methanol oxidation (8.04 mA cm^?2 mg^?1) was found for the SS‐PCz‐Pt electrode in comparison to SS‐Pt electrode (5.01 mA cm^?2 mg^?1) at about 0.6 V (vs. Ag/AgCl).     

The structure of the electrochemical double layer: Ag(111) in alkaline electrolyte

The structure of the electrochemical double layer at the interface between a Ag(111) electrode and 0.1 M KOH electrolyte has been probed using in-situ surface X-ray scattering (SXS). Detailed modeling of the SXS data at negative potential (E = − 1.0 V versus SCE) is consistent with the presence of an hydrated K⁺ cation layer at a distance of 4.1 ± 0.3 Å from the Ag surface and at positive potential (E = − 0.2 V), indicates that the presence of OH_ad stabilizes the hydrated K⁺ cations through a non-covalent interaction forming a compact double layer structure in which the Ag-K⁺ distance is reduced to 3.6 ± 0.2 Å.     

Stepwise Reduction of Azapentabenzocorannulene

Mono‐ and dianions of 2‐tert‐butyl‐3a²‐azapentabenzo[bc,ef,hi,kl,no]corannulene ( 1 a ) were synthesized by chemical reduction with sodium and cesium metals, and crystallized as the corresponding salts in the presence of 18‐crown‐6 ether. X‐ray diffraction analysis of the sodium salt, [{Na⁺(18‐crown‐6)(THF)₂}₃{Na⁺(18‐crown‐6)(THF)}( 1 a ^2?)₂], revealed the presence of a naked dianion. In contrast, controlled reaction of 1 a with Cs allowed the isolation of singly and doubly reduced forms of 1 a , both forming π‐complexes with cesium ions in the solid state. In [{Cs⁺(18‐crown‐6)}( 1 a ^?)]?THF, asymmetric binding of the Cs⁺ ion to the concave surface of 1 a ^? is observed, whereas in [{Cs⁺(18‐crown‐6)}₂( 1 a ^2?)], two Cs⁺ ions bind to both the concave and convex surfaces of the dianion. The present study provides the first successful isolation and characterization of the reduced products of heteroatom‐containing buckybowl molecules.     

Quantum mechanical description of electrode reactions: Part II. Treatment of compact layer structure at platinum electrodes by means of the extended Hückel molecular orbital method. Pt(111) surfaces

The Iteraltive Extended Hückel Molecular Orbital method has been adapted to calculation of the properties of an electrode and compact layer. Predictions of the stablest orientations, on the Pt(111) surface of species such as H₂O, Pt, OH^?, H, and the halides, F^?, Cl^?, Br^? and I^?, based upon calculation of the total energy corresponding to various internuclear distances, are reported. The calculations correctly predict self-adsorption of Pt on the Pt(111) surface at the face-centered cubic closest-packing position. The H₂O molecule is predicted to locate itself above three adjoining Pt atoms, with the O atom closest to the surface and the H atoms opposite the O. Similar results were obtained for OH^? and the halides. Atomic H, however, is predicted to drop into the plane of centers of the Pt surface atoms, where it would lie between, three adjacent Pt atoms. Application of the method to electrode studies requires only modest amounts of computer time but produces surprisingly reliable qualitative predictions. Compulation of electrochemical quantities such as charge, differential capacitance, surface tension and potential energy as a function of electrode potential will be described in future work.     

Influence of F‐ doping on the microstructure,surface morphology and electrochemical properties of the lead dioxide electrode

The lead dioxide electrode (PbO₂) with Ti substrate and SnO₂‐Sb₂O₅ intermediate layer was doped by F^‐ ion through the potentiostatic anode co‐deposition method. The content of F in the coating can be controlled by adjusting deposition potential. The effect of F^‐ doping on the composition, surface morphology and electrochemical properties of the PbO₂ electrode was characterized by X‐ray diffraction, scanning electron microscope, X‐ray photoelectron spectroscopy and electrochemical measurement methods. The results have confirmed that the content of β‐PbO₂ increases with increasing that of F, and the doping can make the β‐PbO₂ grains become fine and the electrode surface become smooth; the specific surface areas and conductivity increase, and the initial potential of oxygen evolution shifts toward positive direction compared with the free‐doped PbO₂ electrode; the oxygen evolution potential increases with the increasing of the F^‐content in the PbO₂ film electrode. The bulk electrolysis result demonstrated that the performances of the F‐PbO₂ electrode for anodic oxidation aniline have been improved to some extent. Copyright © 2012 John Wiley & Sons, Ltd.     

Pt/C电极表面活化处理对乙醇电催化氧化的影响

0引言直接甲醇燃料电池(DMFC)由于其燃料来源丰富、价格低廉、甲醇携带和储存安全方便等独特的优越性而越来越受到重视[1]。但DMFC中常用的阳极Pt催化剂对甲醇氧化的低的电催化活性及易于被甲醇氧化的中间体,吸附态的CO(COad)毒化的问题一直是制约DMFC走向实用化的关键问题[2,3]。由于甲醇分子小,在质子交换膜上有较大的透过作用,并且甲醇具有较高的毒性,所以寻求甲醇的替代燃料也是一直以来被广泛关注的问题[4,5]。乙醇是最简单的链醇分子,相对于甲醇来说,乙醇有很多优点,乙醇基本上没有毒性,来源丰富,价格可与甲醇竞争,能量密度高…     

Effect of Pt,Pd, and Cs<Superscript>+</Superscript> Additives on the Surface State and Catalytic Activity of WO<Subscript>3</Subscript> in Oxidation of Hydrogen

We have shown that additions of Pt(Pd) and Cs⁺ to WO₃ significantly increase its specific surface area and catalytic activity in H₂ oxidation. After reduction, the promoted specimens contain the phases WO₃, WO_2.9, H_xWO₃; and in the case of Cs⁺ additions, Cs_xWO₃. According to X-ray photoelectron spectroscopy (XPS), the Pt and Pd have an oxidation state close to 0, while tungsten has a +5 oxidation state. The W:O ratio indicates the content of oxygen vacancies in the surface layer. The data are explained taking into account hydrogen spillover from Pt(Pd) to the support.__________Translated from Teoreticheskaya i Eksperimental’naya Khimiya, Vol. 41, No. 2, pp. 126–129, March– April, 2005.     

Spontaneous Bi-modification of polycrystalline Pt electrode: fabrication, characterization, and performance in formic acid electrooxidation

Spontaneous modification of polycrystalline Pt by irreversibly adsorbed bismuth was performed in BiCl₃ solution in concentrated hydrochloric acid under open-circuit conditions. After spontaneous modification, followed by extensive rinsing with water and drying, the surface was characterized using X-ray photoelectron spectroscopy and electrochemistry. Bi-oxy(chloride), oxide species, and metallic Bi were found at a submonolayer coverage on the Pt surface after spontaneous modification. The electrochemical response of Bi-modified polycrystalline Pt electrode in sulfuric acid solution exhibits a complex multi-peak feature, which is resulting in about constant redox charge (Bi species coverage) in the potential region from 0 to 0.9 V (vs. a standard hydrogen electrode). The spontaneously Bi-modified Pt catalyst in model studies exhibits a superior activity towards formic acid oxidation at fuel cell anode relevant potentials. The catalytic effect of bismuth oxy-species is explained in terms of both inhibition of CO_ad formation and oxidation of CO_ad in reaction with Bi-oxy-species.     

One‐Electron Oxidation of [M(PtBu3)2] (M=Pd,Pt): Isolation of Monomeric [Pd(PtBu3)2]+ and Redox‐Promoted C−H Bond Cyclometalation

Oxidation of zero‐valent phosphine complexes [M(P^tBu₃)₂] (M=Pd, Pt) has been investigated in 1,2‐difluorobenzene solution using cyclic voltammetry and subsequently using the ferrocenium cation as a chemical redox agent. In the case of palladium, a mononuclear paramagnetic Pd^I derivative was readily isolated from solution and fully characterized (EPR, X‐ray crystallography). While in situ electrochemical measurements are consistent with initial one‐electron oxidation, the heavier congener undergoes C−H bond cyclometalation and ultimately affords the 14 valence‐electron Pt^II complex [Pt(κ²_PC‐P^tBu₂CMe₂CH₂)(P^tBu₃)]⁺ with concomitant formation of [Pt(P^tBu₃)₂H]⁺.     

Pt‐Pd Bimetallic Nanoparticles Decorated Nanoporous Graphene as a Catalytic Amplification Platform for Electrochemical Detection of Xanthine

The nanoporous graphene papers (NGPs) was prepared by the hard‐template method. The Pt−Pd modified NGPs hybrid was prepared by the self‐assembly method. Then a glassy carbon electrode (GCE) modified with Pt−Pd bimetallic nanoparticles‐functionalized nanoporous graphene composite has been prepared for the electrochemical determination of Xanthine (XA). The Pt−Pd/NGPs hybrid was characterized by transmission electron microscopy, scanning electron microscope and X‐ray diffraction. The electrochemical behavior of XA on Pt−Pd/NGPs/GCE was investigated by cyclic voltammetry and amperometric i‐t. The Pt−Pd/NGPs modified electrode exhibited remarkably electrocatalytic activity towards the oxidation reaction of XA in phosphate buffer solution (pH=5.5). Under the optimal conditions, the determination of XA was accomplished by using amperometric i‐t, the linear response range from 1.0×10⁻⁵∼1.2×10⁻⁴ M. The detection limit was 3.0×10⁻⁶ M (S/N=3). The proposed modified electrode showed good sensitivity, selectivity, and stability with applied to determine XA in human urine.     

Synthesis,crystal structure,and electronic structure of Li2PbSiS4: a quaternary thiosilicate with a compressed chalcopyrite‐like structure

The new quaternary thiosilicate, Li₂PbSiS₄ (dilithium lead silicon tetrasulfide), was prepared in an evacuated fused‐silica tube via high‐temperature, solid‐state synthesis at 800 °C, followed by slow cooling. The crystal structure was solved and refined using single‐crystal X‐ray diffraction data. By strict definition, the title compound crystallizes in the stannite structure type; however, this type of structure can also be described as a compressed chalcopyrite‐like structure. The Li⁺ cation lies on a crystallographic fourfold rotoinversion axis, while the Pb²⁺ and Si⁴⁺ cations reside at the intersection of the fourfold rotoinversion axis with a twofold axis and a mirror plane. The Li⁺ and Si⁴⁺ cations in this structure are tetrahedrally coordinated, while the larger Pb²⁺ cation adopts a distorted eight‐coordinate dodecahedral coordination. These units join together via corner‐ and edge‐sharing to create a dense, three‐dimensional structure. Powder X‐ray diffraction indicates that the title compound is the major phase of the reaction product. Electronic structure calculations, performed using the full potential linearized augmented plane wave method within density functional theory (DFT), indicate that Li₂PbSiS₄ is a semiconductor with an indirect bandgap of 2.22 eV, which compares well with the measured optical bandgap of 2.51 eV. The noncentrosymmetric crystal structure and relatively wide bandgap designate this compound to be of interest for IR nonlinear optics.