Extremely highly efficient on-line concentration and separation of gold nanoparticles using the reversed electrode polarity stacking mode and surfactant-modified capillary electrophoresis

In this study, gold nanoparticles (Au NPs) were separated using the reversed electrode polarity stacking mode (REPSM) of a capillary electrophoresis (CE) system for on-line enhancement prior to performing surfactant-modified CE separation. Under optimized conditions [running electrolyte buffer, sodium dodecyl sulfate (70 mM) and 3-cyclohexylamino-1-propanesulfonic acid (10 mM) at pH 10.0; applied voltage, 20 kV; operating temperature, 25°C; REPSM strategy for sample on-line concentration; REPSM applied prior to initializing separation], two parameters were varied to further enhance the concentration and separation of the Au NPs: (i) the rate of polarity switching (from -20 to +20 kV) between the REPSM and surfactant-modified CE separation modes and (ii) the length of the capillary column. At a polarity switching rate of 1333 kV min(-1) and a column length of ca. 83.5 cm, the resolution of the separation of a mixture of 5.3- and 40.1-nm Au NPs was greater than 19; in addition, the numbers of theoretical plates for the 5.3- and 40.1-nm-diameter Au NPs were greater than 15,000 and up to 1.15×10(7), respectively-the latter being extremely high. Thus, this CE-based method for separating Au NPs provided high performance in terms of separation resolution and the number of theoretical plates, both of which were improved by greater than fivefold relative to those published previously. Notably, the sensitivity enhancement factors for the 5.3- and 40.1-nm-diameter Au NPs were improved (by ca. 20- and 500-fold, respectively) relative to those obtained using conventional surfactant-modified CE separation.     

Analytical separation of Au/Ag core/shell nanoparticles by capillary electrophoresis

This paper demonstrates that capillary electrophoresis (CE) can be employed for characterizing the sizes of a series of Au/Ag core/shell nanoparticles (NPs). We effected the CE separation of Au/Ag core/shell NPs using a mixed buffer of sodium dodecyl sulphate (SDS) (40 mM) and 3-(cyclohexylamino)propanesulfonic acid (10 mM) at pH 9.7 and an applied voltage of 20 kV. A linear relationship (R(2)>0.99) existed between the electrophoretic mobilities and the sizes of the Au/Ag core/shell NPs within the diameter range from 25 to 90 nm; the relative standard deviations of these electrophoretic mobilities were <0.9%. From the good correlation between the results obtained by CE and those provided by scanning electron microscopy, we confirmed that this CE method is a valid one for characterizing the sizes of Au/Ag core/shell NP samples. In addition, when the Au/Ag core/shell NPs were separated through CE and detected using an on-line photodiode array detector, this approach allowed the chemical characterization of the NP species. This CE approach should allow the rapid and cost-effective characterization of a number of future nanomaterials.     

Using micellar electrokinetic chromatography for the highly efficient preconcentration and separation of gold nanoparticles

In this paper, we report the use of micellar electrokinetic chromatography (MEKC) for the highly efficient preconcentration and separation of gold nanoparticles (Au NPs). We used the reversed electrode polarity stacking mode (REPSM) of the MEKC system for the on-line enhancement and separation of the Au NPs. Several parameters had dramatic effects on the systems’ performance, including the concentration of sodium dodecylsulfate (SDS) surfactant, the presence of salts in the NP solution, the pH of the running electrolyte, and the temperature of the capillary. Under the optimized conditions [buffer: SDS (70 mM) and 3-cyclohexylamino-1-propanesulfonic acid (CAPS; 10 mM) at pH 10.0; applied voltage: 20 kV; operating temperature: 25 °C; additive: sodium dihydrogenphosphate (NaH₂PO₄, 10 mM); REPSM strategy for sample preconcentration], the number of theoretical plates for the 5.3- and 40.1-nm-diameter Au NPs were 3000 and (an ultrahigh) 2.1 × 10⁶, respectively; in addition, the detection sensitivities toward the Au NPs were enhanced ca. 20- and 380-fold, respectively, relative to those obtained using standard MEKC analysis conditions. Furthermore, monitoring the electropherograms using diode-array detection allowed us to identify and characterize the sizes of the separated NPs from their UV–vis spectra. Our findings suggest that MEKC is a highly efficient tool for both the preconcentration and separation of NPs.     

Rapidly Characterizing the Growth of Au Nanoparticles by CE

In this paper, we describe a capillary electrophoresis (CE)-based method for the rapid characterization of Au nanoparticles (NPs) prepared through seed-assisted synthesis. We effected the CE separation of these Au NPs using a mixed buffer of sodium dodecyl sulfate (SDS; 70 mM) and 3-(cyclohexylamino)-1-propanesulfonic acid (CAPS; 10 mM) at pH 10.0 under an applied potential of 20 kV. A linear relationship (R ² = 0.985) existed between the electrophoretic mobilities and the sizes of the Au NPs within a range of diameters from 5.3 to 59.9 nm; the relative standard deviations of these electrophoretic mobilities were below 0.9%. When using these conditions to analyze the products of seed-assisted syntheses, we found that the rate of addition of the reducing agent affected the size distribution of the NPs dramatically. CE analysis also revealed that the presence of NaOH in the synthesis medium minimized the sizes of the Au NPs. When using these conditions to analyze the Au NPs produced through seed-assisted synthesis, a good correlation existed between the sizes obtained using CE and transmission electron microscopy (TEM). Based on these findings, CE appears to be an efficient tool for characterizing the sizes of NPs fabricated through seed-assisted synthesis.     

Determination of melamine and related triazine by-products ammeline, ammelide, and cyanuric acid by micellar electrokinetic chromatography

In this study, micellar electrokinetic chromatographic (MEKC) methods were developed for the detection of traces of melamine and its related by-products (ammeline, ammelide, and cyanuric acid). Two on-line sample concentration steps namely reversed electrode polarity stacking mode (REPSM) and cation-selective injection (CSI) were used for improving the detection sensitivity. For REPSM, a borate-NaOH buffer (pH 10, 35 mM) composed of 60 mM SDS and 10% (v/v) methanol, was used as carrier electrolyte, and samples were prepared in an aqueous solution of 10 mM NaOH. In CSI, a phosphate buffer (pH 2, 50 mM) containing 41 mM SDS was used as the carrier electrolyte, and samples were prepared with an aqueous solution of 10 mM NaOH and a phosphate buffer (pH 2.0, 25 mM) in a volume ratio of 1:9. The results indicated that REPSM enhanced all analyte signals except for melamine, which could be concentrated only by the CSI. The detection limit was reduced from 1.7 mg L⁻¹ to 2.8 μg L⁻¹ for melamine by the optimal CSI step, and from 0.23-1.2 mg L⁻¹ to 2.4-5.0 μg L⁻¹ for the other three analytes by the optimal REPSM step. Tableware made of melamine and samples of flour were used as test samples, and the results indicated that the proposed MEKC methods can successfully determine contaminations from melamine. The study also indicated that when the plastic made of melamine was exposed only once to an acidic solution (acetic or phosphoric acid) at 80 °C for 30 min, melamine continuously leached out from the test sample even without any further treatment with an acidic solution.     

Determination of pesticides in wine using micellar electrokinetic chromatography with UV detection and sample stacking

In this work, the analysis of a group of four fungicides (pyrimethanil, nuarimol, procymidone and cyprodinil) and one insecticide (pirimicarb) by micellar electrokinetic chromatography (MEKC) with UV detection using the on-line preconcentration strategy called reversed electrode polarity stacking mode (REPSM) is proposed. After optimisation, an adequate separation electrolyte for the separation and stacking of these pesticides was obtained which consisted of 100 mM borate, 60 mM sodium dodecyl sulphate (SDS), at pH 9.0 and 2% 2-propanol. The use of this running buffer together with the REPSM preconcentration method provided limits of detection (LODs) between 38.3 and 241 microg/L. In order to apply the developed methodology for the analysis of these pesticides in wine samples, several off-line preconcentration strategies (mainly, solid-phase extraction, SPE, and solid-phase microextraction, SPME) were tested. Although the use of a SPE procedure, optimized in this work for water samples, using Oasis HLB cartridges, provided mean recovery values between 79 and 100% for spiked water samples, it could not be applied to the extraction of these pesticides from wine samples due to high interference from the sample matrix. However, the use of a SPME procedure using polydimethylsiloxane/divynilbenzene (PDMS/DVB) fibers allowed the selective extraction of four of the five pesticides which could be perfectly determined. The final combination of the off-line SPME and on-line REPSM preconcentration strategies allowed obtaining LODs between 17.6 and 32.3 microg/L.     

MEKC combined with SPE and sample stacking for multiple analysis of pesticides in water samples at the ng/L level

In this work, a new multiresidue analytical method based on MEKC with UV detection combined with SPE as off-line preconcentration strategy, and reversed-electrode polarity stacking mode (REPSM) as on-line stacking procedure, has been developed for the monitoring of 12 pesticides (carbendazim, pirimicarb, metalaxyl, pyrimethanil, procymidone, nuarimol, azoxystrobin, tebufenozide, fenarimol, benalaxyl, penconazole, and tetradifon) that are currently being used in the Canary Islands (Spain). The optimized MEKC buffer, consisting of 100 mM sodium tetraborate and 30 mM SDS at pH 8.5 with 6% v/v 1-propanol, provided baseline resolution of the 12 pesticides in less than 20 min. The developed method was applied to the analysis of mineral, stagnant, and tap water samples. The proposed SPE-REPSM-MEKC-UV method showed high extraction efficiencies with detection limits (LODs) at the low ng/L level providing LOD values down to 64 ng/L for these real samples.     

Novel approach to the analysis and use of fullerenes in capillary electrophoresis

The analysis and use of fullerenes in capillary electrophoresis (CE) was investigated. Sodium dodecyl sulfate (SDS) was used to solubilize fullerenes C60, C70, and a mixture of C60 and C70 in water. The behavior of the solutions of the C60- and C70-SDS complexes was examined by CE with on-line UV-Vis diode array detection. This study included the use of a C60-SDS complex as a new method of micellar electrokinetic chromatography (MEKC) for the separation of polycyclic aromatic hydrocarbons (PAHs) using CE with uniwavelength detection. Since SDS micelles act as a pseudostationary phase in which the PAH compounds partition with their hydrophobic interior, the addition of C60 within the micelles enhanced separation of the PAHs. The preliminary results using C60-MEKC with SDS were compared to those obtained with MEKC with SDS. The capillary electrophoretic separations were performed in 10 mM borate-phosphate buffer with 100 mM SDS at pH 9.5.     

Efficient chemiluminescence by aptamer – reactant platform combination with activated Ag–Au alloy nanoparticles for cobalt detection

This article deals with the detection of Co(II) in real water sample using aptamer – reactant platform combination with activated Ag–Au alloy nanoparticles (NPs) by chemiluminescence (CL) method. CL is attributed to a catalytically enhanced decomposition of H₂O₂ by aptamer conjugated Ag–Au alloy NPs to produce reactive oxygen species. The Ag–Au alloy NPs were prepared by chemical method using double reducing agent (i.e. trisodium citrate and polyethylenimine) and used for detection of Co(II) from water by CL method. CL experiments were carried out with the variation of different parameters such as pH, concentration of luminol, concentration of H₂O₂ and Ag–Au alloy NPs. We found that Ag–Au alloy NPs have very good efficiency towards Co(II) detection. Analytical parameters and kinetics were studied in detail to know the nature and mechanism of CL in presence of aptamer conjugated Ag–Au alloy NPs. The linear range of the CL sensor of Co(II) is covered concentration from 0.01 to 10 µg/L with detection limit of 0.001 µg/L. The relative standard deviation for determination of Co(II) was 6.65 in 10 replicated measurements. CL method is first time applied to detect the Co(II) in real water samples at very low level using aptamer conjugated Ag–Au NPs as a catalyst.     

Separation and on-column preconcentration of some nonsteroidal anti-inflammatory drugs by microemulsion electrokinetic capillary chromatography using high-speed separations

Various strategies have been investigated for separating a group of nonsteroidal anti-inflammatory drugs (NSAIDs) by microemulsion electrokinetic capillary chromatography (MEEKC) using high-speed separations. The parameters that of affect the separation, such as the nature of the oil droplet and the buffer, and the surfactant concentration have been studied. In addition, several organic solvents were used to decrease the retention of the analytes in the oil droplet phase and to improve the resolution of the NSAIDs. The optimum microemulsion background electrolyte (BGE) solution made of 0.8% w/w ethyl acetate, 6.6% w/w butan-1-ol, 6.0% w/w acetonitrile, 1.0% w/w sodium dodecyl sulfate (SDS), and 85.6% w/w of 10 mM sodium tetraborate at pH 9.2 resolved the drugs within 8 min. The short-end injection procedure is an alternative for reducing the analysis time. When this procedure was used, the microemulsion BGE solution consisted of 0.8% w/w ethyl acetate, 6.6% w/w butan-1-ol, 17.0% w/w methanol, 1.0% w/w SDS, and 74.6% w/w of 10 mM sodium tetraborate, pH 9.2, and the NSAIDs were separated within 3 min. The reversed electrode polarity stacking mode (REPSM) technique was applied to the on-line concentration of the NSAIDs. In this technique, the sample matrix was pumped out of the capillary using a polarity-switching step. When this technique was applied, the sensitivity was enhanced up to 40-fold and the limits of detection (LODs) were in the low microg.L(-1) levels.     

Multiple pesticide analysis in wine by MEKC combined with solid-phase microextraction and sample stacking

In this work, a new method for the determination in white wines of 12 pesticides widely used in vine cultivars (namely, carbendazim, pirimicarb, metalaxyl, pyrimethanil, procymidone, nuarimol, azoxystrobin, tebufenozide, fenarimol, benalaxyl, penconazole, and tetradifon) using solid-phase microextraction (SPME) and MEKC with diode-array detection (DAD) was developed. The MEKC buffer consisted of 100 mM sodium tetraborate and 30 mM SDS at pH 8.5 with 6% v/v 1-propanol. Reversed-electrode polarity stacking mode (REPSM) was applied as on-line preconcentration strategy. In order to carry out an effective and sensitive determination of these pesticides in wine samples, an off-line SPME procedure was optimized by means of an experimental design. After studying the extraction performance of different SPME coatings, PDMS/divinylbenzene (PDMS/DVB) fibers were found the most appropriate for the extraction of most of these pesticides. Carbendazim and metalaxyl could not be extracted from wine samples. Calibration curves for extracted standards and fortified white wines were studied in order to determine the presence of a matrix effect. The combination of both preconcentration procedures (SPME and REPSM) allowed the determination of ten of these pesticides in white wines at concentrations between 0.054 and 0.113 mg/L. (i.e., levels well below the maximum residue limits (MRLs) allowed for these compounds in wine grapes). Ten homemade wines were they analyzed with the optimized method demonstrating the usefulness of the proposed procedure.     

CE‐MS analysis of heroin and its basic impurities using a charged polymer‐protected gold nanoparticle‐coated capillary

The first application of charged polymer‐protected gold nanoparticles (Au NPs) as semi‐permanent capillary coating in CE‐MS was presented. Poly(diallyldimethylammonium chloride) (PDDA) was the only reducing and stabilizing agent for Au NPs preparation. Stable and repeatable coating with good tolerance to 0.1 M HCl, methanol, and ACN was obtained via a simple rinsing procedure. Au NPs enhanced the coating stability toward flushing by methanol, improved the run‐to‐run and capillary‐to‐capillary repeatabilities, and improved the separation efficiency of heroin and its basic impurities for tracing geographical origins of illicit samples. Baseline resolution of eight heroin‐related alkaloids was achieved on the PDDA‐protected Au NPs‐coated capillary under the optimum conditions: 120 mM ammonium acetate (pH 5.2) with addition of 13% methanol, separation temperature 20°C, applied voltage ?20 kV, and capillary effective length 60.0 cm. CE‐MS analysis with run‐to‐run RSDs (n=5) of migration time in the range of 0.43–0.62% and RSDs (n=5) of peak area in the range of 1.49–4.68% was obtained. The established CE‐MS method would offer sensitive detection and confident identification of heroin and related compounds and provide an alternative to LC‐MS and GC‐MS for illicit drug control.     

Simultaneous separation of eight beta-adrenergic drugs using titanium dioxide nanoparticles as additive in capillary electrophoresis

The analysis is described for separating seven beta-adrenergic blocking agents (atenolol, celiprolol, clorprenaline, fenoterol, metoprolol, propranolol, terbutaline) and clenbuterol (sympathomimetic beta-2 receptor stimulating agonist, decongestant and bronchodilator, illicit anabolic used in athletics) by CE with UV detection. In order to simultaneously separate all analytes, Tris-H3PO4 solution was applied containing titanium dioxide nanoparticles (TiO2 NPs) as BGEs. The effects of important factors, such as concentration of TiO2 NPs, optimum pH, run buffer concentration, and separation voltage, were investigated so as to achieve best CE separation. The eight analytes could be well separated applying a separation voltage of 15 kV in 75 mM Tris-H3PO4 buffer at a pH of 2.40, containing 6.0 x 10(-6) g/mL TiO2 NPs. Under these optimal conditions, the RSDs for peak areas and for migration times were less than 2.7 and 2.3%, respectively. The detection limits were 0.1 microg/mL for celiprolol, 0.1 microg/mL for propranolol, 0.2 microg/mL for fenoterol, 1.0 microg/mL for atenolol, 1.0 microg/mL for clenbuterol, 1.0 microg/mL for clorprenaline, 1.0 microg/mL for metoprolol, and 1.0 microg/mL for terbutaline. The proposed method was successfully applied for the rapid CE determination of the frequently applied antihypertensive beta-blocking compounds atenolol, metoprolol, terbutaline, and propranolol in pharmaceutical tablets.     

Applications of CE SDS gel in development of biopharmaceutical antibody-based products

CE SDS gel technique offers many advantages over the traditional labor-intensive SDS PAGE slab gel technology. The CE-based method has increasingly been applied to many protein analysis applications. Specific examples are provided for monoclonal antibody (mAb), though the technique can be adapted to many other therapeutic protein products. Applications of CE SDS gel method using Beckman PA800 with UV detection are presented and discussed with respect to mAb analysis, such as purity, quantitation of non-glycosylated heavy chain (NGHC) peak, identity, and stability. The stability of mAb is evaluated with respect to formulation buffer, accelerated temperature stress, UV light-exposure, and high pH conditions. Both reducing and non-reducing CE SDS gel conditions were applied and optimized to characterize mAb products. The data presented provides a "taste" of what CE SDS gel method can do to support the development of mAb products from early clone screening for product quality to the final product characterization. Since the CE SDS gel method is automatable, quantitative, robust, and allows for relatively high throughput, it provides both great analytical capacity and product coverage for a wide spectrum of protein product development in biopharmaceutical industry.     

Sample stacking for the analysis of eight penicillin antibiotics by micellar electrokinetic capillary chromatography

We studied the use of micellar electrokinetic capillary chromatography for separating eight penicillins. The method consists of (i) an electrophoretic separation based on micellar electrokinetic capillary chromatography, which uses sodium dodecyl sulfate (SDS) as surfactant; (ii) a sample stacking technique called reverse electrode polarity stacking mode (REPSM); and (iii) direct UV detection. The background electrolyte that gave complete separation contained 20 mM sodium borate buffer and 60 mM SDS. The sensitivity of the method was improved by an enrichment step that used on-column stacking. The limits of detection were at the microg.L(-1) level for the penicillins and did not detract from the peak resolution.     

Synthesis and characterization of Au core-Au-Ag shell nanoparticles from gold seeds: impacts of glycine concentration and pH

This paper describes the preparation of Au core-Au-Ag shell nanoparticles (NPs) in different morphologies by controlling both the pH and the glycine concentration. Using a seed-growth method, we prepared high-quality Au core-Au-Ag shell NPs from a glycine solution under alkaline conditions (pH>8.5). By controlling both the pH and the glycine concentration, we prepared dumbbell-shaped and peanut-shaped Au core-Au-Ag shell NPs readily by depositing gold and silver, reduced by ascorbate, onto the gold nanorods. We have found that the glycine concentration that is optimal for preparing high-quality Au core-Au-Ag shell NPs differs at the various values of pH. At pH<8.5, the glycine concentration is not important, but, when preparing dumbbell- and peanut-shaped Au core-Au-Ag shell NPs, it should be greater than 50 mM and greater than 20 mM at pH 9.5 and 10.5, respectively. Glycine plays a number of roles during the synthesis of the Au core-Au-Ag shell NPs by controlling the solution pH, altering the reduction potentials of gold and silver ions through forming complexes with metal ions (Au(+) and Ag(+)), minimizing the formation of Ag(2)O, AgCl, and AgBr precipitates, and stabilizing the thus-prepared NPs. At pH 9.7, we observed the changes in the morphologies of the Au core-Au-Ag shell NPs-from regular (rectangular) to peanut- and dumbbell-shaped, and finally to jewel-, diamond-, and/or sphere-shaped-that occurred during the course of a 60-min reaction. In addition, we were able to affect the shapes and sizes of the Au core-Au-Ag shell NPs by controlling the reaction time.     

High-sensitivity capillary electrophoresis for speciation of organomercury in biological samples using hollow fiber-based liquid-liquid-liquid microextraction combined with on-line preconcentration by large-volume sample stacking

A hollow fiber-based liquid-liquid-liquid microextraction (HF-LLLME) combined with on-line large-volume sample stacking (LVSS) has been developed for the speciation of organomercury in biological samples by CE with UV detection. Separation was achieved in less than 11 min with an electrolyte consisting of 35 mM sodium tetraborate at pH 9.1. In LVSS, a reverse electrode polarity-stacking mode (REPSM) was applied as on-line preconcentration strategy. In HF-LLLME, the analytes were extracted from 12 mL volume of sample solution (pH adjusted to 3.0) into bromobenzene impregnated in the pores of the hollow fiber, and into an acceptor solution of L-cysteine (15 microL, 0.02% w/v) inside the hollow fiber. Under the optimized conditions, concentration factors of 2610-4580 were achieved and LODs in the range of 0.03-0.14 microg/L were feasible. The linearity was found to be over two orders of magnitude with correlation coefficient of 0.9991-0.9996. The developed method has been validated using a certified reference material (DORM-2, dogfish muscle), and the determined values coincided very well with the certified values. The method was also applied to the speciation of organomercury in three kinds of fish samples and human hair samples.     

On-line microheterogeneity analysis and rapid phenotyping of haptoglobin by capillary electrophoresis using sodium dodecyl sulfate as additive

To improve the detection sensitivity and determine phenotypes of haptoglobin (Hp), a prefilling technique was developed and tested in capillary electrophoresis (CE) with UV–vis absorbance detection. Adding 0.01% sodium dodecyl sulfate (SDS) to the protein sample and 0.1% SDS to the prefilling buffer solution, on-line stacking and microheterogeneity separation of Hp were achieved. In addition, the influences of pH, buffer concentration, sample and prefilling buffer SDS concentration upon resolution were examined. Under optimized conditions, Hp-microheterogeneity was well resolved and two phenotypes of Hp (Hp 1-1 and Hp 2-2) were differentiated. This method was applied to the analysis of sera from normal individuals and β-Thalassemia patients. After the depletion of albumin (HSA) and immunoglobulin G (IgG), this method allowed to determine two phenotypes in different individuals and to detect the decrease of Hp in β-Thalassemia patients. Featuring high efficiency, speed and simplicity, the proposed method shows great potential for use in clinical diagnosis and proteome research.     

Determination of triazine compounds in ground water samples by micellar electrokinetic capillary chromatography

In this work, a capillary electrophoresis (CE) method for the determination of a group of eleven triazine compounds by micellar electrokinetic capillary chromatography (MEKC) with diode array detection was developed. The eleven herbicides studied were: desethylatrazin-2-hydroxy (DEA), simazine, prometon, atrazine, simetryn, ametryn, propazine, prometryn, trietazine, terbutylazine, and terbutryn The separation of these compounds was optimised as a function of buffer concentration and pH, concentration of sodium dodecyl sulphate (SDS) and voltage applied. To increase the selectivity of the separation and the resolution of the solutes, different organic solvents were tested as buffer additives, obtaining the best results when 1-propanol was used. The optimised buffer (24 mM of sodium borate, 18 mM of disodium hydrogen phosphate, 25 mM of SDS, pH 9.5, and 5% of 1-propanol) provides the best separation in terms of resolution and migration time. This method allowed the determination of these compounds at concentrations of 0.05 μg l⁻¹ in ground water samples pretreated using solid-phase extraction (SPE).     

SEC Characterization of Au Nanoparticles Prepared through Seed-Assisted Synthesis

In this paper we report the use of size-exclusion chromatography (SEC) for rapid determination of the sizes and size distributions of Au nanoparticles (NPs) prepared by seed-assisted synthesis. Analytical separation of Au NPs was performed in a polymer-based column of pore size 400 nm. We characterized the sizes and size distributions of the Au NPs by using 10 mM sodium dodecyl sulfate (SDS) as mobile phase and obtained a linear relationship (R ² = 0.986) between retention time and size of Au NPs within the range 9.8–79.1 nm; the relative standard deviations of these retention times were less than 0.3%. These separation conditions were used to characterize the sizes and size distributions of Au NPs prepared by seed-assisted synthesis. In addition to observing the elution times of the Au NPs we also simultaneously characterized their size-dependent optical properties by spectral measurement of the eluting peaks by use of an on-line diode-array detector (DAD), i.e., monitoring of the stability of the Au NP products. By using this approach we found the presence of SDS was beneficial in stabilizing the synthesized Au NPs. We also found that the volume of Au metal ions used affected the sizes of the final products. SEC seems an efficient tool for characterizing the sizes of NPs fabricated by seed-assisted synthesis.