Analysis of pyrolysis products formed from ethylene-tetrafluoroethylene heterosequences of poly(ethylene-co-tetrafluoroethylene)

Poly(ethylene-co-tetrafluoroethylene) (PETFE) was pyrolyzed and the pyrolysis products formed from the ethylene-tetrafluoroethylene heterosequences were analyzed using gas chromatography/mass spectrometry (GC/MS). Major pyrolysis products were 3,3-difluoropropene (DFP), 3,3,4,4-tetrafluoro-1-butene (TFB), 1,1,2,2,3,3-hexafluorocyclopentane (HFCP), 1,1,2,2,3,3-hexafluorocyclohexane (HFCH), 1,1,2,2,3,3,4,4-octafluorocyclohexane (OFCH), and 3-trifluoromethyl-3,4,4,5,5-pentafluorocyclohexene (FMPFCH). Their formation mechanisms were proposed. Peak intensity ratios of HFCP, HFCH, and FMPFCH compared to OFCH increased as the pyrolysis temperature increased, while those of DFP, TFB, HFCP, and HFCH compared to tetrafluoroethylene decreased. Order of the relative abundances of the major pyrolysis products formed from PETFE was OFCH > HFCP > HFCH > TFB > DFP. The order may be due to the difference in bond energies of CH₂-CH₂, CF₂-CH₂, and CF₂-CF₂. Formation of the pyrolysis product through the CH₂-CH₂ bond cleavage was more favorable than those through the CF₂-CH₂ and CF₂-CF₂ ones.     

Polymer reactions—Part VII: Thermal pyrolysis of polypropylene

Polypropylene has been pyrolysed in a carrier stream of helium from 388° to 900°C in both the programmed heating and flash pyrolysis modes. The products were on-line identified and quantitatively analysed by an interfaced GC peak identification system. The first order rate constants for pyrolysis are 3·7 × 10^?4 sec^?1 and 4·0 × 10^?4 sec^?1, respectively, for atactic and isotactic polypropylene at 388°C; the corresponding overall activation energies are 56 ± 6 and 51 ± 5 kcal mole^?1. The main products in decreasing yields are 2,4-dimethyl-1-heptene, 2-pentene, propylene, 2 methyl-1-pentene and 2,4,6-trimethyl-1-nonene. Also isolated, but in much smaller quantities, are: ethane, isobutylene, 4,6-dimethyl-2-nonene, 2,4,6-trimethyl-1-heptene, 3-methyl-3,5-hexadiene and methane. Propylene is the product of an unzipping reaction. Most of the other products can be accounted for by a mechanism involving first, random scission of carbon-carbon bonds to produce methyl, primary and secondary alkyl radicals, followed by intramolecular hydrogen transfer processes. Methane and ethane are formed from the methyl radicals. All the products found in high yields are derived from the secondary alkyl radicals.     

Cationic and free-radical polymerization of optically active 1-olefins

The AlCl₃-initiated cationic polymerization of optically active 1-olefins yields polymers of varying optical rotatory power. Polymers of (+)-3-methyl-1-pentene and (?)-4-methyl-1-hexene prepared between ?78 and ?55°C. in CH₂Cl₂ or n-heptane are almost completely optically inactive. Under identical reaction conditions (+)-5-methyl-1-heptene gives polymers of significant optical rotatory power. Alternating SO₂copolymers of the same olefins, formed in reactions which proceed through free-radical intermediates, yield optically active products with specific rotations similar to those of low molecular weight analogs. These results are consistent with a cationic polymerization mechanism in which the growing chain undergoes intramolecular hydride shift and the asymmetric carbon atoms are converted into carbonium ions. The data also provide evidence for the lack of rearrangement in free-radical polymerization. By comparing the specific rotations of the cationic and free-radical polymers, the extent of rearrangement during cationic polymerization can be estimated. The calculations show that the 1,2-polymer in cationic poly-3-methyl-1-pentene is less than 2%, the sum of 1,2- and 1,3-polymer in cationic poly-4-methyl-1-hexene is less than 4%, and the sum of 1,2-, 1,3-, and 1,4-polymer in cationic poly-5-methyl-1-heptene is 14–20%.     

PVT properties of polyethylene copolymer melts

PVT properties of four polyethylene random copolymers (ethylene-propylene, ethylene-1-butene, ethylene-1-hexene, and ethylene-1-octene) and linear polyethylene were measured at temperatures from 313 to 493 K and pressures up to 200 MPa. Dependence of properties such as specific volume, thermal expansion coefficient, isothermal compressibility, and characteristic parameter of equations of state on the length of the polymer branched chains were examined. It was found that the length of the branched chain did not affect the thermal expansion coefficient and isothermal compressibility. The specific volume of copolymers having longer branched chains were slightly larger than those copolymers with short branched chains.     

Radiolysis of liquid propylene: Ion-molecule condensation

Radiolysis of propylene gives mainly hydrogen, and dimeric, trimeric, and other low molecular weight polymeric hydrocarbons.

Detailed analysis of the dimer shows the products to be, in order of concentration, 4-methyl-1-pentene, 1,5-hexadiene, 1-hexene, 2-methylpentane, 2,3-dimethylbutane, 4-methyl-2-pentene, 2-methyl-1-pentene, 2-hexene, and n-hexane.

The relative product concentrations, and the isotope species distribution in the products obtained from radiolysis of a 50:50 mixture of propylene and propylene-d₆, demonstrate that the alkanes, the diene, and much of the olefinic products are formed by combinations of n-propyl, isopropyl, and allyl radicals.

Isotopic species distributions in 4-methyl-1-pentene, 1-hexene, and 2-hexene demonstrate that appreciable fractions of each of these products are formed by a direct condensation of two propylene molecules with intramolecular hydrogen rearrangement. The previously postulated direct dimerization is thus verified, and the idea of its being an ion-molecule condensation receives further support.     

Microstructural analysis of poly(vinylidene fluoride) using benzene derivative pyrolysis products

Poly(vinylidene fluoride) (PVDF) was pyrolyzed, and the pyrolysis products were analyzed using gas chromatography/mass spectrometry (GC/MS) to develop a method for identification of the microstructures of head-to-tail (H-T), tail-to-tail (T-T), and head-to-head-to-tail-to-tail (H-H-T-T) sequences. Key pyrolysis products to determine the relative degrees of the microstructures were benzene derivatives. 1,4-Difluorobenzene, 1,2,4-trifluorobenzene, and 1,3,5-trifluorobenzene were major pyrolysis products as benzene derivatives. 1,3,5-Trifluorobenzene and 1,2,4-trifluorobenzene were formed from two HF-eliminated PVDF by 1,6-HF elimination and 1,6-rearrangement, while 1,4-difluorobenzene was generated from two HF-eliminated PVDF by 1,6-H₂ elimination and 1,6-rearrangement. 1,3,5-Trifluorobenzene was generated from the H-T sequence, whereas 1,4-difluorobenzene was formed from the T-T one. 1,2,4-Trifluorobenzene can be formed from the H-H-T-T sequence. Relative component ratios of the H-T, T-T, and H-H-T-T sequences of PVDFs can be estimated by comparing relative abundances of the benzene derivative pyrolysis products.     

Aromaticity in azlactone anions and its significance for the Erlenmeyer synthesis

Azlactone anions—the key intermediates in the classical Erlenmeyer synthesis of amino acids—apparently possess aromatic stabilization, as indicated by the relative rate of base catalyzed deuterium exchange in the following analogs: 1-methyl-2-phenyl-5(4H)-imidazolone > 2-phenyl-5(4H)-oxazolone (azlactone) > 3,3-dimethyl-2-phenyl-4(3H)-pyrrolone. This is paralleled by the relative rate of condensation of these compounds with hexadeuteroacetone. Reported pK_a data also suggest that the azlactone products of the Erlenmeyer synthesis are analogs of the fulvenes.     

Isomerization of alkenes in the presence of Pd(acac)2-BF3OEt2 catalytic system

Positional isomerization of alkenes was studied in the presence of Pd(acac)₂ + 20BF₃OEt₂ catalytic system. The reactivity of alkenes decreases in the following order: 1-hexene > 1-heptene > 2-methyl-1-pentene > 4-methyl-2-pentene (cis + trans).     

Selection of entrainers in the 1-hexene/n-hexane system with a limited solubility

Vapor-liquid equilibria (VLE) have been measured for five 1-hexene/n-hexane/ionic liquid systems and 1-hexene/n-hexane/NMP (N-methyl-2-pyrrolidone) system with a headspace-gas chromatography (HSGC) apparatus at 333.15 K. The ionic liquids investigated were 1,3-dimethylimidazolium tetrafluoroborate [C₂MIM]⁺[BF₄]⁻, 1-butyl-3-methylimidazolium tetrafluoroborate [C₄MIM]⁺[BF₄]⁻, 1-methyl-3-octylimidazolium tetrafluoroborate [C₈MIM]⁺[BF₄]⁻, 1,3-dimethylimidazolium dicyanamide [C₂MIM]⁺[N(CN)₂]⁻ and 1-octylquinolinium bis(trifluoromethylsulfonyl)amide [C₈Chin]⁺[BTA]⁻. It was found that at low feeding concentration of 1-hexene and n-hexane, the separation ability of ionic liquids is in the order of [C₂MIM]⁺[BF₄]⁻ > [C₄MIM]⁺[BF₄]⁻ ≈ [C₂MIM]⁺[N(CN)₂]⁻ > [C₈MIM]⁺[BF₄]⁻ > [C₈Chin]⁺[BTA]⁻, which is consistent with the priori prediction of the COSMO-RS (conductor-like screening model for real solvents) model. But at high feeding concentration, the separation ability of ionic liquids is in the order of [C₂MIM]⁺[BF₄]⁻ < [C₄MIM]⁺[BF₄]⁻ ≈ [C₂MIM]⁺[N(CN)₂]⁻ < [C₈MIM]⁺[BF₄]⁻ < [C₈Chin]⁺[BTA]⁻. The liquid demixing effect should be taken into account. The activity coefficients of 1-hexene and n-hexane at infinite dilution calculated with the COSMO-RS model were correlated using the NRTL, Wilson and UNIQUAC model. In this work the predictive results from the COSMO-RS model and UNIFAC model for the 1-hexene/n-hexane and 1-hexene/n-hexane/NMP systems were compared. The UNIFAC model is one of the most important academic contributions by Prof. Jürgen Gmehling.     

Reaction of oxochloroalkenes with phosphorous acid esters

Conclusions 2-Qxo-3-methyl-5-chloro-3-hexene and trans-2-oxo-5-chloro-3-heptene, adequate low-molecular-weight models of labile carbonylallyl groups in poly(vinyl chloride) macromolecules, were synthesized. Tributyl phosphite reacts with the model compounds at the oxovinylene fragment via a step of formation of intermediate phosphorane structures, which are converted to stable ketophosphonates during heating.Translated from Izvestiya Akademii Nauk SSSR, Seriya Khimicheskaya, No. 5, pp. 1106–1108, May, 1985.     

Thermal decomposition products of copoly(arylene ether sulfone)s characterized by direct pyrolysis mass spectrometry

Pyrolysis products with mass of up to 850 Da were detected by direct pyrolysis mass spectrometric (DPMS) analysis of a series of copoly(arylene ether sulfone)s (PES-PPO) synthesized by nucleophilic condensation of either 4,4′-dichlorodiphenylsulfone (CDPS) or 4,4′-bis-(4-chlorophenyl sulfonyl) biphenyl (long chain dichloride, LCDC) with different molar ratios of hydroquinone (HQ) or dihydroxydiphenylsulfone (HDPS). Pyrolysis products retaining the repeating units of the initial copolymers were formed at temperatures ranging from 420 °C to 470 °C (near the initial decomposition temperature). At temperatures higher than 450 °C were observed products containing biphenyl units, formed by the elimination process of SO₂ from diphenyl sulfone bridges. Products having biphenyl and dibenzofuran moieties were detected in the mass spectra recorded at temperatures above 550 °C. These units were formed by loss of hydrogen atom from diphenyl ether bridges. Although the EI (18 eV) mass spectra of the pyrolysis products of the samples investigated were very similar, it was found that the relative intensity of some ions reflects the molar composition of the copolymers analysed. Cyclic and linear oligomers with very low molecular mass, present in the crude copolymers, were also detected by DPMS. Thermogravimetric analysis also showed their excellent thermal stability below 400 °C. It indicates that the copolymers yield a char residue of 40-45% at 800 °C, which increases with the PPO mole fraction in the samples.     

Mass spectrometric study of the pyrolysis of perfluorinated compounds of composition C6F12-C9F20, containing perfluoroisopropyl groups

The primary and final products arising from the pyrolysis of perfluoro-2,4-dimethyl-3-ethylpentane, perfluoro-3-isopropyl-4-methyl-2-pentene, perfluoro-2-methyl-3-isopropyl-2-pentene, perfluoro-2,4-dimethyl-3-heptene, and perfluoro-4-methyl-2-pentene have been studied using low-energy mass spectrometry and chromatography-mass spectrometry. Thermal decomposition of hexafluoropropene oligomers, containing perfluoroisopropyl groups attached to a double bond, occurs via loss of a radical pair to form perfluorodienes, as well as via abstraction of a hexafluoropropene molecule from the iso-C₃F₇ group. A correlation between the principal fragmentation pathway observed under electron impact and the primary process in the main thermolysis pathway was detected only in the case of perfluoro-4-methyl-2-pentene and perfluoro-2,4-dimethyl-3-heptene, which are capable of cleavage of^.CF₃ and^.C₂F₅ radicals, respectively, to give a single possible allyl radical structure.Translated from Izvestiya Akademii Nauk SSSR, Seriya Khimicheskaya, No. 5, pp. 1037–1041, May, 1990.     

Co-oligomerization of ethylene and higher linear alpha olefins. I. Co-oligomerization with the sulfonated nickel ylide-based catalytic system

Co-oligomers of ethylene and a series of linear α-olefins (propylene, 1-butene, 1-hexene, 1-heptene, 1-octene, and 1-decene) were synthesized with a homogeneous catalyst consisting of sulfonated nickel ylide and diethylaluminum ethoxide at 90°C. GC analysis of the co-oligomerization products allowed complete structural identification of all reaction products, α-olefins with linear and branched chains, vinylidene olefins, and linear olefins with internal double bonds. The article describes the reaction scheme of ethylene–olefin co-oligomerization. The scheme includes chain initiation reactions (insertion of ethylene or an olefin into the Ni? H bond), chain propagation reactions, and chain termination reactions via β-hydride elimination. Primary and secondary inertions of α-olefins into the Ni? H bond in the initiation stage proceed with nearly equal probabilities. Higher olefins participate in the chain growth reactions (insertion into the Ni? C bond) also both in primary and secondary insertion modes. The primary insertion of an α-olefin molecule into the Ni? C bond produces the β-branched Ni? CH₂? CR₁R₂ group. This group is susceptible to β-hydride elimination with the formation of vinylidene olefins. However, the Ni? CH₂? CR₁R₂ groups can participate in further ethylene insertion reactions and thus form vinyl oligomerization products with branched alkyl groups. On the other hand, the secondary insertion of an α-olefin molecule into the Ni? C bond produces the α-branched Ni? CR₁R₂ bond which does not participate in further chain growth reactions and undergoes the β-hydride elimination reaction with the formation of linear reaction products with internal double bonds. Most co-oligomer molecules contain only one α-olefin fragment. However, the analysis of ethylene-propylene and ethylene-1-heptene co-oligomers allowed identification of products with two olefinic fragments which are also formed in the copolymerization reactions with small yields.     

Determination of the adsorption model of alkenes and alcohols on sulfonic copolymer by inverse gas chromatography

The determination of a number of adsorption sites on sulfonated styrene-divinylbenzene copolymer for alkenes (propene, 1-butene, 1-pentene, 1-hexene, 1-heptene, isobutene, 2-methyl-1-butene, 2-methyl-2-butene, 2-methyl-1-pentene, 2-methyl-2-pentene and 2-methyl-2-hexene) and alcohols (methanol, ethanol and n-propanol, n-butanol, 2-butanol and tert-butanol) was performed by the saturation copolymer with vapors of adsorbate, by removing the excess of adsorbate from copolymer by blowing the inert gas through copolymer bed and by the desorption of adsorbed alcohol in the programmed increase of temperature. The adsorption measurements were performed on sulfonated ion-exchange resin (Amberlyst 15) with different concentrations of the acid group, which means with a varying number of adsorption sites. The following adsorption models for alkenes were suggested: the first in which one molecule of alkene is adsorbed by two sulfonic groups, for linear alcohols, the second in which one sulfonic group can adsorb one molecule of alcohol and for non-linear alcohols the third where one molecule of alcohol is adsorbed by two or more sulfonic groups.     

Ternary liquid–liquid equilibria for mixtures of 1-hexyl-3-methylimidozolium (tetrafluoroborate or hexafluorophosphate) + ethanol + an alkene at T=298.2 K

Liquid–liquid equilibrium data are presented for mixtures of {1-hexyl-3-methylimidozolium(tetrafluoroborate or hexafluorophospate) + ethanol + (1-hexene or 1-heptene)} at T=298.2 K. The data presented provides valuable insight into how variation of the anion of the environmentally friendly ionic liquid solvent can have a marked effect upon the separation power of ionic liquids. The sloping of the tie lines towards the ethanol vertex is observed for mixtures of {1-hexyl-3-methylimadozolium tetrafluoroborate + ethanol + (1-hexene or 1-heptene)}, whilst the reverse, i.e. sloping of the tie lines towards the ionic liquid vertex is observed for mixtures of {1-hexyl-3-methylimadozolium hexafluorophospate + ethanol + (1-hexene or 1-heptene)}. The tie line data have been correlated through the use of the NTRL model for statistical consistency. Selectivity values, derived from the tie line data, indicate that these two ionic liquids are suitable solvents for the liquid–liquid extraction of ethanol from olefins.     

Thermal hydrosilylation of olefin with hydrosilane. Preparative and mechanistic aspects

The reaction of trichlorosilane (1a) at 250 °C with cycloalkenes, such as cyclopentene (2a), cyclohexene (2b), cycloheptene (2c), and cyclooctene (2d), gave cycloalkyltrichlorosilanes [C_nH_2n−1SiCl₃: n = 5 (3a), 6 (3b), 7 (3c), 8 (3d)] within 6 h in excellent yields (97-98%), but the similar reactions using methyldichlorosilane (1b) instead of 1a required a longer reaction time of 40 h and afforded cycloalkyl(methyl)dichlorosilanes [C_nH_2n−1SiMeCl₂: n = 5 (3e), 6 (3f), 7 (3g), 8 (3h)] in 88-92% yields with 4-8% recovery of reactant 2. In large (2, 0.29 mol)-scale preparations, the reactions of 2a and 2b with 1a (0.58 mol) under the same condition gave 3a and 3b in 95% and 94% isolated yields, respectively. The relative reactivity of four hydrosilanes [HSiCl_3−mMe_m: m = 0-3] in the reaction with 2a indicates that as the number of chlorine-substituent(s) on the silicon increases the rate of the reaction decreases in the following order: n = 3 > 2 > 1 ? 0. In the reaction with 1a, the relative reactivity of four cycloalkenes (ring size = 5-8) decreases in the following order: 2d > 2a > 2c > 2b. Meanwhile linear alkenes like 1-hexene undergo two reactions of self-isomerization and hydrosilylation with hydrosilane to give a mixture of the three isomers (1-, 2-, and 3-silylated hexanes). In this reaction, the reactivity of the terminal 1-hexene is higher than the internal 2- and 3-hexene. The redistribution of hydrosilane 1 and the polymerization of olefin 2 occurred rarely under the thermal reaction condition.     

The first example of tungsten-based carbene generation from WCl6 and atomic carbon and its use in olefin metathesis

We describe a new route for the synthesis of tungsten-based carbenes generated by the reaction of WCl₆ with atomic carbon in a carbon arc reactor. The active species formed under these conditions, [W] = CCl₂, was found to catalyze olefin metathesis reactions of 1-octene, 2-octene and 1-heptene. We also evaluated the mechanism of formation of [W] = CCl₂ within the WCl₆/C system at the DFT level.     

Catalytic isomerization of 1-hexene on hy zeolite

The isomerization of 1-hexene on 70/80 mesh HY zeolite was studied at 200°C. The observed reaction products are formed via a variety of processes including double bond shift, cis–trans isomerization, skeletal rearrangement, cracking, hydrogen transfer, polymerization, cyclization, and coke formation. By applying the time-on-stream theory, the products have been classified as primary, secondary, or both, according to their OPE curves on product selectivity plots. 2-Ethyl-1-butene, which is present as an impurity in the feed, is found to react about 30 times faster than 1-hexene. Both 2-hexenes and 3 hexenes are formed primarily from 1-hexene, while 3 methyl 2 pentenes and 3-methyl-1-pentene formed from 2-ethyl-1-butene. The ratio of the initial rate of deprotonation to that of hydrogen shift in these reactions is ～15 and ～100, respectively. All products of skeletal rearrangement are observed to be secondary. Cracking products are produced mainly from precoke, which is also the source of hydrogen in the formation of paraffins. A detailed reaction network along with its associated mechanisms are presented and discussed.     

Synthesis of multi-walled carbon nanotubes catalyzed by substituted ferrocenes

A range of substituted ferrocenes were used as catalysts for the synthesis of multi-walled carbon nanotubes (MWCNTs) and carbon fibers (CFs). These products were obtained in the temperature range 800-1000 °C, in a reducing atmosphere of 5% H₂ by pyrolysis of (CpR)(CpR′)Fe (R and R′ = H, Me, Et and COMe) in toluene solution. The effect of pyrolysis temperature (800-1000 °C), catalyst concentration (5 and 10 wt.% in toluene) and solution injection rate (0.2 and 0.8 ml/min) on the type and yield of carbonaceous product synthesized was investigated. Carbonaceous products formed include graphite film (mostly at high temperature; 900-1000 °C), carbon nanotubes and carbon fibers. The carbonaceous materials were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM) and Raman spectroscopy. The ferrocene ring substituents influenced both the CNT diameter and the carbon product formed.