Degradation of organic pollutants by visible light synergistic electro-Fenton oxidation process

Visible light irradiation combined with homogeneous iron and/or hydrogen peroxide to degrade organic dye rhodamine B (RhB) and small molecular compound 2,4-dichlorophenol (2,4-DCP) in a home-made bottle reactor was assessed. The concen-tration of oxidize species, Fe3+ and Fe2+ were determined during the degradation process. The results demonstrated that visible light irradiation combined with electro-Fenton improved the degradation efficiency. Moreover, both RhB and 2,4-DCP were mineralized during visible light synergistic electro-Fenton oxidation process. 95.0% TOC (total organic carbon) removal rate of RhB occurred after 90 min and 96.7% of COD (chemical oxygen demand) removal rate after 65 min of irradiation. 91.3% TOC removal rate of 2,4-DCP occurred after 16 h of irradiation and 99.9% COD removal rate occurred after 12 h of illumination. The degradation and oxidation process was dominated by the hydroxyl radical ( · OH) generated in the system. Both the impressed electricity and dye sensitization by visible light facilitated the conversion between Fe3+ and Fe 2+ , thus, improving Fenton reaction efficiency.     

Interaction of L-3,4-dihydroxyphenylalanin (L-DOPA) as a coordinating ligand with a series of metal ions; reaction of L-DOPA

L-DOPA is an important neurotransmitter that is found in the brain and as a hormone in the circulatory system. We report in this article the similarities and differences in behaviour of this important neurotransmitter as a chelating agent among some divalent and trivalent metal ions using potentiometric titration in aqueous solutions at 25.0?±?1.0°C. The careful and detailed potentiometric titrations of L-DOPA with Al³⁺, Cr³⁺, Fe³⁺, Cu²⁺, and Zn²⁺ are discussed and compared. UV-Vis-spectroscopy is utilized for both the free L-DOPA and for the Fe³⁺/L-DOPA system. The characteristic peak due to the π?→?π* transition of the free L-DOPA at ～280?nm (ε_280?nm?=?1927?±?65?M^?1?cm^?1 between pH values of 2.0 to 3.0) disappeared when the iron solution was added to the L-DOPA sample in the same pH range. For the Fe³⁺/L-DOPA system we have observed a new peak at 470?nm with ε₄₇₀?=?800?±?50?M^?1?cm^?1. These comparison studies of the similarities and differences among these di- and tri-valent metal ions shed light on these systems in aqueous solutions. The appropriate metal simulation and speciation diagrams were constructed using the model that fit the titration data points.     

An electrochemical sensor for p-aminophenol based on the mesoporous silica modified carbon paste electrode

A mesoporous silica was synthesised and used to modify the surface of carbon paste electrode (CPE). The electrochemical behaviours of p-aminophenol were investigated. Compared to the unmodified CPE, the mesoporous silica-modified CPE obviously lowers the oxidation potential of p-aminophenol, and remarkably increases its oxidation peak current. The effects of pH value, amount of mesoporous silica, accumulation potential and time were examined. As a result, a sensitive, rapid and convenient electroanalytical method was developed for p-aminophenol. The linear range is from 0.025?mg?L^?1 to 3?mg?L^?1, and the limit of detection is 0.01?mg?L^?1 after 2-min accumulation. Finally, the method was successfully used to determine p-aminophenol in water samples.     

Simple and efficient treatment of high-strength industrial waste water using commercial zero-valent iron

The zero-valent iron (ZVI)/H₂O₂ Fenton system can be considered as an effective solution for the removal of many of the organic pollutants present in the waste waters generated by the drug manufacturing industry. The hydrogen peroxide concentration and dosage rate were studied in order to improve the efficiency of the oxidant in the TOC reduction and, thereby enhance the overall catalytic performance of the ZVI/H₂O₂ Fenton system. TOC reductions of up to 80 % and BOD₅/COD ratios of up to 0.6 were achieved in the waste water as received without dilution (TOC_O approximately 5 g L^?1) using hydrogen peroxide dose-staggering. This showed that the ZVI/H₂O₂ process led not only to a decrease in TOC removal but also to an increase in the biodegradability of the by-products formed. The hydrogen peroxide was consumed more efficiently and very low concentrations of iron dissolved (7 mg L^?1) were obtained in the final effluents. The final values of COD, BOD₅, the suspended solids’ content and the conductivity of the treated waste water met the limits of the Spanish legal industrial discharge, Decree 57/2005 (Ministry of Environment, Local Government and Planning, Community of Madrid, 2005). In addition, the composite thus formed, consisting of zero-valent iron and iron oxide-oxyhydroxides, can be readily removed from the treated effluent, avoiding any post-treatment step.     

Electrochemical investigation of a glassy carbon electrode modified with carbon nanotubes decorated with (poly)crystalline gold

Multiwalled carbon nanotubes with nanosized sputtered gold were used to modify a glassy carbon electrode (GCE). The substrate was characterized by scanning electron microscopy (SEM), X-ray diffraction, cyclic voltammetry and amperometry. SEM micrographs indicated an uniform coverage of the carbon nanotubes with nanosized (poly)crystalline gold. Cyclic voltammetry reveals that peak separation of the unmodified GCE in the presence of 1?mM ferricyanide is 131?mV, but 60?mV only for the modified GCE. In addition, the oxidation of NADH (1?mmol?L^?1 solution) begins at negative potentials (around ?100?mV vs. Ag/AgCl), and the anodic peak potential (corresponding to the irreversible oxidation of NADH) is found at +94?mV. The effect of pH on the electrocatalytic activity was studied in the range from 5.4 to 8.0. The relationship between the anodic peak potential and the pH indicated a variation of ?33.5?mV/pH which is in agreement with a two-electron and one-proton reaction mechanism. Amperometry, performed at either ?50 or +50?mV vs. an Ag/AgCl reference electrode, indicates that the modified electrode is a viable amperometric sensor for NADH. At a working potential of +50?mV, the response to NADH is linear in the concentration range from 1 to 100???mol?L^?1, with an RSD of 6% (n?=?4).

Electroanalytical Determination of Morpholine as a Corrosion Inhibitor at a Cathodically Pretreated Boron-Doped Diamond Electrode

An electroanalytical method for the determination of morpholine, a corrosion inhibitor, was developed at a cathodically pretreated boron-doped diamond electrode (BDDE). The voltammetric response of morpholine at the BDDE in 0.1?mol L^?1 KCl (pH 10) shows an irreversible oxidation process at approximately 1.3?V vs. Ag/AgCl in 3.0?mol L^?1 KCl. Using cyclic voltammetry, the number of electrons involved in the morpholine electroxidation mechanism was found to be 1. The application of chronoamperometry showed that the apparent diffusion coefficient (D₀) was 2.99?×?10^?6 cm² s^?1. Using square wave voltammetry under the optimized conditions (frequency of 30.0?Hz, pulse amplitude of 100?mV and step potential of 20?mV at pH 10.0), the developed method provided limits of detection and quantification of 2.1 and 6.9?mg L^?1, respectively, with a linear range from 5.0 to 100.0?mg L^?1 (r?=?0.991). Intraday (n?=?10) and interday (two consecutive day) precision values assessed as the relative standard deviation for solutions containing 30.0, 60.0, and 90.0?mg L^?1 of morpholine were from 0.41 to 5.86% and 0.92 to 3.19%, respectively. The feasibility of the method for the interference-free determination of morpholine was verified by the analysis of synthetic boiler water samples containing CaCO₃, Na₂SO₃, Na₃PO_4, FeCl₃, and humic acid as organic matter. In addition, hydrazine was added as a possible interfering compound because of its widespread use in corrosion inhibition. Recovery values from 90.9 to 109.4% were obtained in the synthetic boiler water, thereby attesting to the accuracy of the method.     

Application of Photo-Fenton,Electro-Fenton,and Photo-Electro-Fenton processes for the treatment of DMSO and DMAC wastewaters

Biological treatment, due to the formation of hazardous chemicals to remove organic compounds such as dimethyl sulfoxide (DMSO) and N, N-dimethylacetamide (DMAC), has limited potential. Advanced oxidation processes (AOPs) are regarded as a viable alternative for treating molecules containing carbon-hydrogen bonds that cannot be broken down by traditional physico-chemical methods. In this investigation, various AOPs such as Photo-Fenton, Electro-Fenton, and Photo-Electro-Fenton processes were studied to treat wastewaters containing DMSO and DMAC. The effects of the operating parameters, including various initial concentrations of DMSO and DMAC, initial pH, reaction time, different concentrations of Fenton’s reagent, power of UV lamp, different concentrations of electrolytes, the distance between electrodes and current intensity, were investigated. The findings of the experiments revealed that a pH of 3 and a reaction time of 120 min were optimal. At 2000 mg L^?1 of DMSO, maximum degradation and the final concentration of TOC were 98.64 % and 256.8 mg L^?1, respectively, by the Electro-Fenton process under the optimal conditions. The Electro-Fenton process was successful in determining the maximum degradation of DMAC (96.31 %) and the final TOC concentration (10.03 mg L^?1) at 250 mg L^?1 of DMAC under optimal conditions. Finally, it can be concluded that the Electro-Fenton process was the best process for the efficient removal of DMSO and DMAC. The second step of the kinetic model follows a pseudo-first-order reaction for 250 and 500 mg L^?1 of pollutants and obeyed a pseudo-second-order kinetic model for concentrations of 1000, 2000 mg L^?1.     

MnO2 nanozyme induced the chromogenic reactions of ABTS and TMB to visual detection of Fe2+ and Pb2+ ions in water

In this study, we used a simple and rapid colourimetric reaction for visual sensing of Fe²⁺ and Pb²⁺ ions in water by employing nano-MnO₂ as a natural oxidase mimic to respectively catalyse ABTS and TMB in citrate-phosphate buffer solution (C-PBS) at 25°C and pH 3.8. It was found that nano-MnO₂ possessed highly oxidase-mimicking activity with the K_m values of 0.030 and 0.027 toward ABTS and TMB, respectively, indicating TMB had a stronger affinity on nano-MnO₂ than ABTS. Interestingly, the presence of 0.01 mmol·L^?1 Fe²⁺/Pb²⁺ ion was able to significantly down-regulate the activity of MnO₂ nanozyme in nano-MnO₂-mediated ABTS reaction processes (P < 0.01), which mainly due to the strong adsorption of metal ion toward nano-MnO₂ surface via the electrostatic attractions, thus leading to the passivation and inactivation of MnO₂ nanozyme catalytic activity. Thereinto, Fe²⁺ reacted with multivalent manganese by oxidation-reduction, while Pb²⁺ was specifically adsorbed onto the surface of MnO₂ nanozyme and formed complexes. Notably, only Fe²⁺ ion inhibited the activity of MnO₂ nanozyme-TMB with a detection limit as low as 1.0 μmol·L^?1. In MnO₂ nanozyme-ABTS sensing systems, Fe²⁺ and Pb²⁺ ions detection limit of 0.5 and 2.0 μmol·L^?1 were, respectively, achieved with a linear response range of 0–0.02 and 0–0.8 mmol·L^?1, implying the developed MnO₂ nanozyme-ABTS sensor was potentially applicable for the visual determination of Fe²⁺ and Pb²⁺ ions in water. In the real water samples, MnO₂ nanozyme-ABTS achieved high accuracy (relative errors: 3.4?10.5%) and recovery (96?110%) for respective detection of Fe²⁺ and Pb²⁺ ions. The simple and rapid MnO₂ nanozyme-ABTS sensing systems might provide a practical assay for visual detection of Fe²⁺ and Pb²⁺ ions in the environmental water samples.     

Simultaneous spectrophotometric determination of iron species using orthogonal signal correction–generalized partial least squares calibration method after vortex-assisted dispersive liquid–liquid microextraction

A vortex-assisted dispersive liquid–liquid microextraction method in combination with UV–Vis spectrophotometry was developed for the simultaneous extraction and determination of iron species. In this method, Fe²⁺ and Fe³⁺ were complexed with pyridine-2-amidoxime, neutralized through ion pair formation with sodium dodecyl sulfate, and extracted into the fine droplets of chloroform. After centrifugation, the absorbance of the extracted complexes was recorded in the wavelength range of 360–700 nm. The parameters affecting the extraction efficiency such as the pH, the type and volume of the extraction solvent, ligand concentration, and sample volume were optimized. The individual iron species was then determined by means of the orthogonal signal correction–generalized partial least squares method. Under the optimized conditions, the calibration curves were linear over the range of 2.0–100 and 3.0–200 µg L^?1 with detection limits of 0.4 µg L^?1 for Fe²⁺ and 0.8 µg L^?1 for Fe³⁺, respectively. The relative standard deviations for intra- and inter-day assays (n = 5) were 2.3 and 4.0 for Fe²⁺ at 50 µg L^?1 and 2.7 and 4.3 for Fe³⁺ at 30 µg L^?1, respectively. The enhancement factors of 77 and 69 were achieved for Fe²⁺ and Fe³⁺, respectively. The proposed method was successfully applied to the determination of iron species in water samples.     

Optimization and Degradation Mechanism of Photocatalytic Removal of Bisphenol A Using Zn0.9Fe0.1S Synthesized by Microwave‐assisted Method

The sulfide photocatalyst of Zn_0.9Fe_0.1S was successfully synthesized by a facile microwave‐assisted method, and Zn_0.9Fe_0.1S photocatalysts were characterized using SEM, EDX, XRD and BET. The specific surface area of synthesized Zn_0.9Fe_0.1S is 78.1 m² g^?1, and total pore volume is 0.4 cm³ g^?1. With bisphenol A (BPA) as a target pollutant, photocatalytic system of UV + Zn_0.9Fe_0.1S + H₂O₂ was set up. Some influencing parameters, including H₂O₂ dosage, initial pH value, initial concentration of BPA and Zn_0.9Fe_0.1S dosage, were investigated, and the stability of the Zn_0.9Fe_0.1S was also studied during the photocatalysis. The optimum values of operating parameters were found at an initial pH value of 5.0, a H₂O₂ dosage of 0.15 mmol L^?1 and a Zn_0.9Fe_0.1S dosage of 0.08 g when the initial concentration of BPA was 10 mg L^?1. Under the optimal conditions, the highest removal rate of BPA achieved 95%. After seven consecutive reaction cycles, the degradation efficiency of BPA could still reach 85% and there was only a little dissolution of Zn²⁺ and Fe²⁺. Compared with the traditional photo‐Fenton system, the UV + Zn_0.9Fe_0.1S + H₂O₂ system can not only improve the degradation efficiency of BPA, but also reduce the dosage of H₂O₂ and thus reduce the processing cost.     

Removal of Lead(II), Cadmium(II), and Arsenic(III) from Aqueous Solution Using Magnetite Nanoparticles Prepared by Green Synthesis with Box–Behnken Design

Two types of magnetite (Fe₃O₄) nanoparticles were investigated as adsorbents for the simultaneous removal of Pb(II), Cd(II), and As(III) metal ions from aqueous solution. Magnetite nanoparticles were prepared by two synthesis procedures, both using water as solvent, and are referred to as conventional Fe₃O₄ nanoparticles and green Fe₃O₄ nanoparticles. The latter used Citrus limon (lemon) aqueous peel extract as the surfactant. Box–Behnken experimental design was used to investigate the effects of parameters such as initial concentration (20–150?mg?L^?1), pH (2–9), and biomass dosage (1–5?g?L^?1) on the removal of Pb(II), Cd(II), and As(III) ions. The optimum parameters for removal of the studied metal ions from aqueous solutions, including the initial ion concentration (20?mg?L^?1), pH (5.5) and adsorbent dose (5?g?L^?1), were determined. The pseudosecond-order model exhibited the best fit for the kinetic studies, while adsorption equilibrium isotherms were best described by Langmuir and Freundlich models. The optimum conditions were applied for the treatment wastewater. The removal efficiencies of Pb(II), Cd(II), and As(III) using the conventional and green synthesized Fe₃O₄ nanoparticles were 59.4?±?4.3, 18.7?±?1.9 and 17.5?±?1.6, and 98.8?±?5.6, 46.0?±?1.3, and 48.2?±?2.6%, respectively. These results demonstrate the potential of magnetite nanoparticles synthesized using C. limon peel extract as highly efficient adsorbents for the removal of Pb(II), Cd(II), and As(III) ions from aqueous solution.     

Novel sensor based on carbon paste/Nafion? modified with gold nanoparticles for the determination of glutathione

Several problems for the direct electrochemical oxidation of reduced glutathione (GSH) challenge the usage of electroanalytical techniques for its determination. In this work, the electrochemical oxidation of GSH catalyzed by gold nanoparticles electrodeposited on Nafion modified carbon paste electrode in 0.04?mol?L^?1 universal buffer solution (pH?7.4) is proved successful. The effect of various experimental parameters including pH, scan rate and stability on the voltammetric response of GSH was investigated. At the optimum conditions, the concentration of GSH was determined using differential pulse voltammetry (DPV) in two concentration ranges: 0.1?×?10^?7 to 1.6?×?10^?5?mol?L^?1 and 2.0?×?10^?5 to 2.0?×?10^?4?mol?L^?1 with correlation coefficients 0.9988, 0.9949 and the limit of detections (LOD) are 3.9?×?10^?9?mol?L^?1 and 8.2?×?10^?8?mol?L^?1, respectively, which confirmed the sensitivity of the electrode. The high sensitivity, wide linear range, good stability and reproducibility, and the minimal surface fouling make this modified electrode useful for the determination of spiked GSH in urine samples and in tablet with excellent recovery results obtained.     

Determination of cadmium, chromium and copper in high salt samples by LA-ICP-OES after electrodeposition—preliminary study

A novel method is presented for determination of heavy metal ions in a high-saline matrix. It is based on the electrodeposition of the ions and subsequent laser ablation coupled to inductively coupled plasma optical emission spectrometry (LA-ICP-OES). Three arrangements for electrodeposition were worked out, two of them with stationary working electrodes. Materials for use in the working electrodes, and conditions for electrodeposition of Cd, Cr and Cu (pH, deposition current, time of electrolysis) were studied. Nickel was found to be the best electrode material. The metals accumulate on the surface of electrode and were then evaporated/ablated with a Nd:YAG laser focused into the ICP-OES spectrometer. The detection limits are 0.13 mg?L^?1 for Cd, 0.15 mg?L^?1 for Cu, and 1.9 mg?L^?1 for Cr in case of a stationary bottom working electrode, and 0.25 mg?L^?1 for Cd, 0.05 mg?L^?1 for Cu, 0.8 mg?L^?1 for Cr when using a rotating electrode. The relative standard deviation is in range from 3.8 to 10.3%. Waste water was analyzed in this way by the standard addition method.     

Electrochemical determination of paraquat using a DNA-modified carbon ionic liquid electrode

Deoxyribonucleic acid (DNA) was electrochemically deposited on a carbon ionic liquid electrode to give a biosensor with excellent redox activity towards paraquat as shown by cyclic voltammetry and differential pulse voltammetry. Experimental conditions were optimized with respect to sensing paraquat by varying the electrochemical parameters, solution pH, and accumulation time of DNA. Under the optimized conditions, a linear relation exists between the reduction peak current and the concentration of paraquat in the range from 5?×?10^?8 mol L^?1 to 7?×?10^?5 mol L^?1, with a detection limit of 3.6?×?10^?9 mol L^?1. The utility of the method is illustrated by successful analysis of paraquat in spiked real water samples.

Determination of Nitrite in Aqueous Solutions using the Linear Sweep Voltammetry Technique

ABSTRACT

An electrochemical method using linear sweep voltammetry techniques was developed to determine nitrite ion in aqueous solution in the presence of nitrate. Nitrite solutions exhibited a well-defined oxidation wave at +1.0V vs SCE at vitreous carbon, while no oxidation process was observed for nitrate solutions. The pH of the nitrite solutions varied from 2.37 to 5.60 and no change was observed in the Ep values, except for the pH 5.60 solution, where little change was verified. The potential also did not vary with change in the nitrite concentration in the 5.0 x 10^?5 to 7.0 x 10^?4 mol L^?1 range. Very good straight lines for plots of current versus nitrite concentration in the 7.0 x 10^?5 to 7.0 x 10^?4 mol L^?1 range were obtained; the correlation coefficient was never worse than 0.990. The nitrite determination was also performed in the presence of 1.0 x 10^?3 mol L^?1 of NO₃ ^? ions. The addition of NO₃ ^? did not change significantly the current values even when it was added in one hundred times molar excess.     

Electrocatalysis Oxidation of GMP Based on Layered Double Hydroxide Functionalized with Anionic Surfactant and Room Temperature Ionic Liquid Modified Glassy Carbon Electrode

The electrocatalysis oxidation of guanosine‐5′‐monophosphate (GMP) was investigated on Mg‐Al layered double hydroxide (LDH) functionalized with sodium dodecyl sulfate (SDS) and room temperature ionic liquid (RTIL) modified glass carbon electrode (GCE). The cyclic voltammogram of GMP on the modified electrode (RTIL/ LDH‐SDS/GCE) exhibited a well defined anodic peak at 1.091 V in 0.2 mol·L^?1 pH 4.4 acetate buffer solution. The GMP oxidation was enhanced in the presence of anionic surfactant in the ?lms. The results suggest that the surfactant molecules intercalate the LDH layers to preconcentrate GMP molecules and the RTIL showed good ionic conductivity. The experimental parameters were optimized, the kinetic parameters were investigated and the probable oxidation mechanism was proposed. Under the optimized conditions, the oxidation peak current was proportional to GMP concentration in the range from 5.0×10^?7 to 1.0×10^?4 mol·L^?1 with the correlation coefficient of 0.9987 and the detection limit was 1.0×10^?7 mol·L^?1. The RTIL/LDH‐SDS/GCE showed a good electrochemical response to the oxidation of GMP and would be developed into a new biosensor.     

Voltammetric detection of guanosine and adenosine using a carbon paste electrode modified with 1-ethyl-3-methylimidazolium ethylsulfate

A novel kind of carbon paste electrode (CPE) was prepared by mixing graphite powder, liquid paraffin and the ionic liquid 1-ethyl-3-methylimidazolium ethylsulfate. The resulting electrode was used for the simultaneous determination of guanosine and adenosine by differential pulse voltammetry. Compared to a conventional CPE, the oxidation peak currents are largely increased, and the oxidation peak potentials are negatively shifted. The electrochemical responses to guanosine and adenosine were investigated. Under optimized conditions, the calibration curves are linear in the concentration range from 1.0?×?10^-6?mol?L^-1 to 1.6?×?10^-4?mol?L^-1 for guanosine, and from 1.0?×?10^-6?mol?L^-1 to 2.7?×?10^-4?mol?L^-1 for adenosine at pH 3.5. Substances potentially interfering in the biological matrix do no interfere. The method was successfully applied to detect adenosine and guanosine in human urine without sample treatments.

Resveratrol and arctigenin production from polydatin and arctiin respectively by a thermostable β-glucosidase from Thermotoga maritima

Abstract

For preparation of resveratrol and arctigenin from peanut hulls and arctium lappa fruits, respectively, a recombinant β-glucosidase (TmBglA) from hyperthermophile Thermotoga maritima was purified and characterized. The hydrolytic activity was the highest at 90?°C and pH 6.2 for arctiin with K_m of 1.61?mM and k_cat of 197.4?s^?1, and 90?°C and 5.8 for polydatin with K_m of 0.38?mM and k_cat of 47.6?s^?1. The enzyme produced 215.4?mg L^?1 resveratrol and 355.7?mg L^?1 arctigenin from 400?mg L^?1 polydatin and 540?mg L^?1 arctiin after 60?min of incubation at 80?°C, with capable of hydrolyzing up to 92.1 and 94.9% of polydatin and arctiin, respectively. The enzymatic hydrolysis of peanut hulls and fructus arctii displayed a conversion yield of 3.8 and 0.33?mg resveratrol and arctigenin per gram of substrate material flour, respectively. Of the reported β-glucosidase, TmBglA exhibited the highest thermostability, k_cat, k_cat/K_m, and conversion productivity for hydrolyzing polydatin and arctiin, and has great potential applications in functional food and medicine production.     

Heterogeneous Fenton Degradation of Organic Pollutants in Water Enhanced by Combining Iron-type Layered Double Hydroxide and Sulfate

Water pollution derived from organic pollutants is one of the global environmental problems. The Fenton reaction using Fe²⁺ as a homogeneous catalyst has been known as one of clean methods for oxidative degradation of organic pollutants. Here, a layered double hydroxide (Fe²⁺Al³⁺-LDH) containing Fe²⁺ and Al³⁺ in the structure was used to develop a “heterogeneous” Fenton catalyst capable of mineralizing organic pollutants. We found that sulfate ion (SO₄²⁻) immobilized on the Fe²⁺Al³⁺-LDH significantly facilitated oxidative degradation (mineralization) of phenol as a model compound of water pollutants to carbon dioxide (CO₂) in a heterogeneous Fenton process. The phenol conversion and mineralization efficiency to CO₂ reached >99% and ca. 50%, respectively, even with a reaction time of only 60 min.     

Determination of Tetracycline in Water and Honey by Iron(II,III)/Aptamer-Based Magnetic Solid-Phase Extraction with High-Performance Liquid Chromatography Analysis

A novel aptamer-based adsorbent was prepared for the magnetic solid-phase extraction of tetracycline. The Fe₃O₄/aptamer adsorbent was fabricated by immobilizing an aptamer on the surface of Fe₃O₄ magnetic nanoparticles by the reaction between avidin and biotin. The parameters affecting the isolation efficiency such as the pH, extraction time, extraction temperature, eluent, and elution time were investigated in detail. Under the optimal conditions, a linear relationship between the peak area and the concentration of tetracycline was observed in the range from 10.0 to 3000.0?µg L^?1 with a correlation coefficient of 0.9985 and a limit of detection of 2.5?µg L^?1. The developed method was successfully employed for the determination of tetracycline in honey and water samples with recovery values from 82.9 to 107.3% and relative standard deviations less than 7.6%. Compared with previously reported methods for the determination of tetracycline, the proposed protocol provides improvements in the limit of detection and specificity with reduced consumption of adsorbent and organic solvents.